T3 SMOOTH ID 76535 (01) PDF MANUAL

T3 SMOOTH ID 76535 (01) PDF SUMMARY:

How do you turn the T3 Smooth ID on?

Connect the styling iron to a power source. The Power Button will light up. To turn on, press and hold the lit Power Button until the tool vibrates, and lights start to cascade up. The styling iron will automatically start in HeatID mode. The screen will be unlocked and the HeatID icons will light up and blink for you to input your hair profile.

---

What should you avoid when turning the iron ON or OFF?

Do not touch the area above the power button when turning the iron ON or OFF.

---

How do you switch between HeatID and Manual Mode?

If you prefer to manually select your temperature, you can switch to Manual Mode.

---

How do you lock/unlock the screen?

Double tap the Power Button to lock and unlock the screen. You will hear a locking sound to indicate lock and unlock.

---

What does it mean if the screen is locked?

When the screen is locked, the screen is inactive, thus you cannot change settings if locked.

---

What does it mean if the screen is unlocked?

When the screen is unlocked, the screen is active, thus you can change settings if unlocked.

---

How do you turn the T3 Smooth ID off?

To turn off, first unlock the tool by quickly double tapping the Power Button. Then press and hold the Power Button until the iron vibrates and the lights start to cascade down. The Power Button will remain on until unplugged.

---

How do you adjust settings on second time use?

On second time use, the iron will immediately begin heat up to your previous heat setting. To adjust settings follow instructions.

---

How does HeatID mode work?

Enter your hair texture, length, and color treatment inputs, and T3 Smooth ID will automatically tailor your heat setting to help protect against heat damage and deliver one-pass results.

---

How do you identify your hair texture?

Run one hair strand between your fingers.

• Can you barely feel and see the strand? Select Fine hair texture.
• Can you feel the strand, but it does not feel very thick and textured? Select Medium hair texture.
• Does the strand feel and look thick and textured? Select Coarse hair texture.

Note: If still unsure about your hair texture, select the Medium hair texture. You may need to manually adjust heat as necessary.

---

How do you identify your hair length?

• Is your hair length above the chin? Select Short hair length.
• Is your hair neck to shoulder-length? Select Medium hair length.
• Is your hair below the shoulder? Select Long hair length.

---

How do you identify if you need to select the color treatment option?

If you answer yes to any of these questions, select the Color Treatment option:

• Is your hair 3 or 4 shades lighter or darker than your natural color?
• Is your hair fragile?
• Is your hair damaged?
• Is your hair bleached?

---

How do you select your HeatID profile?

The HeatID icons will be blinking on first time use. Tap through each icon to select desired hair profile input. Icons will stop blinking upon first tap and your selection will become brighter as you continue to tap.

---

How do you lock your HeatID profile?

Double tap the Power Button to lock in your HeatID profile. The temperature lights will cascade up to your personalized heat setting and the iron will begin to heat up.

---

How do you know when the T3 Smooth ID is ready to use in HeatID mode?

Once the styling iron beeps and the lights turn solid, it has reached your HeatID setting and is ready to use.

---

What do you do if you experience accidental activation during styling?

Keep your hand away from the Power Button to avoid unintended interface activation during styling.

---

What do you do if the interface is not responsive?

• Ensure you are only touching a single area of the interface at a time. If contact is made with more than one area at the same time, the tool may not respond.
• Ensure the screen is unlocked. To unlock screen, quickly double tap the Power Button.
• If tool is still unresponsive, unplug, wait 15 seconds, and plug in again.

---

What do you do if the power button is not visible?

• Ensure the tool is plugged in.
• If tool is plugged in, unplug, wait 15 seconds, and plug in again.

---

What do you do if your tool won’t turn on?

• Ensure you are holding the Power Button for a full 3 seconds.
• Avoid touching surface area above Power Button while turning on the tool.
• If tool still will not turn on, unplug, wait 15 seconds, and plug in again.

---

What should you do during first use?

Use iron with caution, and select settings with caution. There are individual variations in how hair responds to heat. The optimal selection of settings may vary from person to person. In the first use, it is best to test at a low heat and for a short duration. If there are any adverse or unexpected effects, stop use of the iron immediately.

---

How do you switch to manual mode if it is the first time use?

Tap the Power Button once after turning on the tool. You will hear a beep. The HeatID icons will go away and the Temperature Panel will appear.

---

How do you switch to manual mode if it is the second time use?

1. First unlock the styling iron by quickly double tapping the Power Button. You will hear an unlock sound.
2. Tap the Power Button one more time to switch from HeatID to Manual Mode. You will hear a beep. The HeatID icons will go away and the Temperature Panel will appear.

---

How do you select a heat setting in Manual Mode?

To increase heat: Tap the top of the Temperature Panel. To decrease the heat: Tap the bottom of the Temperature Panel.

---

How do you lock your heat setting in Manual Mode?

Double tap the Power Button to lock the screen and T3 Smooth ID will begin to heat up. Note: Iron will auto lock after 10 seconds of inactivity.

---

How do you know when the T3 Smooth ID is ready to use in Manual Mode?

Once the styling iron beeps and the lights turn solid, the iron has reached your heat selection and is ready to use.

---

What is the temperature guide for Manual Mode?

For optimal results, select the right heat setting for your hair type. It is suggested to start at a lower setting and building your way up as needed.

• Fine: #1-4
• Medium: #5-6
• Coarse: #7-9
  • 9 – 410ºF / 210ºC
  • 8 – 400ºF / 205ºC
  • 7 – 390ºF / 199ºC
  • 6 – 370ºF / 188ºC
  • 5 – 350ºF / 177ºC
  • 4 – 325ºF / 163ºC
  • 3 – 300ºF / 149ºC
  • 2 – 280ºF / 138ºC
  • 1 – 260ºF / 127ºC

If your hair is color-treated or damaged, reduce temperature by 1-2 heat settings.

---

How do you enter Refresh Mode?

1. Unlock Screen: Double tap the Power Button to unlock the screen.
2. Enter Refresh Mode: Tap the Refresh Mode Button. You will hear a beep and the temperature panel will turn blue. Lights will cascade heating up to your Refresh temperature.

---

How do you know when the T3 Smooth ID is ready to use in Refresh Mode?

When you hear a beep and lights turn solid, begin styling.

---

How do you exit Refresh Mode?

Double tap the Power Button to unlock the screen. Tap the Refresh Mode Button to return to your previous heat setting. You will hear a beep and the HeatID or Temperature panel lights will go back to white. Note: The styling iron will automatically exit Refresh Mode when turned off.

---

What is Refresh Mode?

Refresh Mode is for retouching your second-day styles with less heat. Refresh Mode automatically reduces your previously saved heat setting to help protect your hair, boost shine, and reduce frizz on second-day retouches.

---

How do you reset the iron to original factory settings?

To reset the iron to original factory settings, unlock screen, then press and hold the Power and Refresh Mode Buttons simultaneously until the styling iron turns off. Follow the instructions to set your new settings.

---

How do you use the T3 Smooth ID?

1. Start with dry, detangled hair. Twist the top part of your hair out of the way and secure it with a sectioning clip. Gather the rest of your hair into another clip, leaving a 1-2" section out to begin styling.
2. To avoid kinks, style your hair using thin, horizontal sections so the iron can be positioned close to the roots.
3. Glide iron through in the direction of hair growth at a speed slower than when brushing hair. Continue working with thin sections, repeating steps 2 and 3 until hair is fully styled.

---

What is the expert tip for the glide speed of the iron?

Slow down for perfect results in a single glide:

• Fine hair: Glide iron at 2-3 inches per second
• Medium Hair: Glide iron at 2 inches per second
• Coarse Hair: Glide iron at 1 inch per second

---

What are the maintenance instructions for the T3 Smooth ID?

1. Your appliance is virtually maintenance free. It contains no user serviceable parts, and no lubrication is needed.
2. Keep heated surfaces clean and free of dust, dirt & hairspray.
3. If cleaning becomes necessary, disconnect the appliance from the power source and let it cool. Wipe the exterior with a damp cloth.
4. If any malfunction occurs, unplug the appliance, allow it to cool and return it to a service center to repair.
5. Never wrap the cord around the appliance since this will cause the cord to wear prematurely and break. If the cord becomes twisted, untwist it prior to use.
6. Handle the cord carefully for longer life and do not put any stress on the cord where it enters the handle. Avoid jerking, twisting or straining especially at the plug connections. It could cause the cord to fray and possibly break.
7. Do not attempt to repair the appliance yourself.

---

How should the T3 Smooth ID be stored?

When not in use, your styling iron should be disconnected and stored in a safe, dry location, out of reach of children. Do not wrap the cord around the styling iron. Allow the cord to hang or lie loose and straight at the point of connection.

---

What does the limited warranty cover?

T3 Micro will repair or replace (at our option) T3 products for twenty-four (24) months from the date of purchase if they are defective in workmanship or materials. This limited warranty does not cover (1) damage due to misuse or abuse, such as incorrect voltage supply, dropping, or failure to follow enclosed instructions or (2) tampering, such as repair or attempt to repair.

---

How do you obtain service under the warranty?

To obtain service under this warranty, please visit http://www.T3Micro.com/warranty-info to submit a warranty claim, or call at (866) 376-8880 to receive detailed instructions. You will be required to provide proof of purchase.

---

What are the conditions for the limited warranty to be valid?

THIS LIMITED WARRANTY IS ONLY VALID IF THE PRODUCT IS PURCHASED FROM AN AUTHORIZED SELLER OF T3 GOODS AND IF THE ORIGINAL SERIAL NUMBER ON THE PRODUCT HAS NOT BEEN REMOVED OR OTHERWISE TAMPERED WITH.

---

Where can you complete the warranty registration?

Visit http://www.T3Micro.com/customer-service to complete your warranty registration.