SUMMIT APPLIANCE FFRF106PL (01) PDF Document

Before connecting the SUMMIT APPLIANCE FFRF106PL to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

Clean the interior surface of the SUMMIT APPLIANCE FFRF106PL with lukewarm water using a soft cloth.

Install the handle on the door of the SUMMIT APPLIANCE FFRF106PL, if it is not already attached.

The SUMMIT APPLIANCE FFRF106PL is designed for free standing installation for indoor use.

Keep 4″ of space between the back and the sides of the SUMMIT APPLIANCE FFRF106PL unit and 11” at the top to allow proper air circulation to cool the compressor and condenser.

The SUMMIT APPLIANCE FFRF106PL requires a standard 115/120 Volt AC ~60Hz three-prong grounded electrical outlet. The size of the fuse (or circuit breaker) should be 15 amperes.

Adjust the left and right front leveling feet to ensure your refrigerator-freezer is on a horizontal level.

Turn the front leveling feet clockwise to increase the height of your refrigerator-freezer.

Turn the front leveling feet counterclockwise to lower the height of your refrigerator-freezer.

The tools needed for reversing the door swing on the SUMMIT APPLIANCE FFRF106PL are:

• Phillips head screwdriver
• 5/16″ socket and rachet
• Flat-head screwdriver
• Masking tape
• Putty knife

The steps for reversing the door swing are:

1. Unplug the appliance, and remove all items from the door shelves and the interior.
2. Remove the hinge hole cover from the top left side of the appliance.
3. Remove the upper hinge cover from the top right side of the appliance. Then, remove the hinge screws and upper hinge.
4. Lift the upper door off of the cabinet.
5. Place the upper door on a soft surface to ensure the door is not scratched or damaged.
6. Unscrew the middle hinge screws, and remove the middle hinge.
7. Remove the two hinge hold plugs, the screw, and screw cap from the middle beam on the opposite side of the appliance.
8. Remove the refrigerator door from the cabinet.
9. Carefully tip the unit back, and remove the adjusting feet, lower hinge screws, and the lower hinge assembly.
10. Install the lower hinge assembly on the other side of the cabinet, and install the adjusting feet again.
11. Dismantle the limit blocks and screws on the lower cover of the refrigerator and freezer door. Install them on the opposite side of both doors. Then, install the sleeve pipe on the upper cover of the refrigerator door on the other side.
12. Set the refrigerator door onto the lower hinge, and then install the middle hinge and hinge hole caps.
13. Set the freezer door onto the middle hinge, and then install the upper hinge to secure the freezer door, making sure to secure the hinge cover and hinge hole cover.

The control panel of the SUMMIT APPLIANCE FFRF106PL features a SET key and five temperature settings. The settings cycle from 1 (coldest) to 5 (least cold) each time the SET key is pressed.

When an error occurs on the SUMMIT APPLIANCE FFRF106PL, the corresponding LED light combination corresponds to the specific error as follows:

To clean the exterior surface of the SUMMIT APPLIANCE FFRF106PL, wipe it with a soft cloth dampened with soapy water or diluted detergent, and then wipe dry.

Check the door gasket regularly to make sure there is no accumulated debris. Clean the door gasket with a soft cloth dampened with soapy water or diluted detergent.

The interior of the SUMMIT APPLIANCE FFRF106PL should be cleaned regularly to avoid any odor buildup.

Do not use soap, detergent, scrub powder, spray cleaner, etc., as these may cause odors in the interior of the refrigerator.

Use a soft cloth or sponge to clean the inside of the unit, using a solution of two tablespoons of baking soda and a quart of warm water. Then rinse with clean water, and then wipe clean with a soft towel. After cleaning, open the door and let the unit dry naturally before turning the power back on.

For areas that are difficult to clean in (such as narrow gaps or corners), it is recommended to wipe them regularly with a soft rag or brush, or when necessary, an auxiliary tool (such as a thin stick) to ensure no contaminant or bacterial accumulation in these areas.

To clean the glass shelves of the SUMMIT APPLIANCE FFRF106PL:

1. Lift up the front of the glass shelf, and then pull the shelf out.
2. Clean as needed.
3. Reinstall the shelf by placing the rear of the shelf into position first. Then, carefully lower the front of the shelf into place.

The SUMMIT APPLIANCE FFRF106PL uses an automatic defrosting function. Frost formed due to the change of season or temperature may also be manually removed by disconnecting the appliance from the power supply or by wiping with a dry towel.

In case of a power failure in the SUMMIT APPLIANCE FFRF106PL, even in warmer weather, foods inside the appliance can be kept for several hours; during the power failure, limit the times the door is opened, and do not add more fresh food into the appliance.

Before the SUMMIT APPLIANCE FFRF106PL unit is moved:

• Remove all of the items stored inside, fix the glass shelves, drawers, freezing chamber drawers, etc. with tape, and tighten the leveling feet.
• Then, close the doors and fix them with tape.

During moving, the SUMMIT APPLIANCE FFRF106PL shall not be laid upside down or horizontally, or be vibrated; the inclination during movement shall be no more than 45°.

For short vacations, leave the SUMMIT APPLIANCE FFRF106PL operating during vacations of less than three weeks.

For long vacations, if the SUMMIT APPLIANCE FFRF106PL will not be used for several months, remove all items and turn the unit off. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly, blocking it open if necessary.

If the unit stops working on the SUMMIT APPLIANCE FFRF106PL, check the following:

• Check whether the appliance is connected to power or whether the plug is in well contact.
• Check whether the voltage is too low.
• Check whether there is a power failure or partial circuits have tripped.

If there is an odor inside the SUMMIT APPLIANCE FFRF106PL:

• Tightly wrap food to prevent possible odor.
• Check whether there is any rotten food.
• Clean the inside of the appliance.

The compressor on the SUMMIT APPLIANCE FFRF106PL might run too long for several reasons:

• Long operation of the compressor is normal in summer when the ambient temperature is high.
• It is not recommended to load a large amount of food in the appliance at one time. Cool food to room temperature before loading into the appliance.
• The doors are opened too frequently.

If the light fails to turn on in the SUMMIT APPLIANCE FFRF106PL, check whether the appliance is connected to power supply and whether the illuminating light is damaged.

The doors on the SUMMIT APPLIANCE FFRF106PL cannot be properly closed if the door is blocked by food packages or if the appliance is not level.

To troubleshoot loud noise from the SUMMIT APPLIANCE FFRF106PL, check whether the floor is level and whether the appliance is placed stably. Check whether accessories are placed at proper locations.

If the door seal fails to be tight on the SUMMIT APPLIANCE FFRF106PL:

• Remove foreign matters on the door seal.
• Heat the door seal and then cool it for restoration (e.g. blow it with an electrical drier or use a hot towel for heating).

Water pan overflows in the SUMMIT APPLIANCE FFRF106PL can be caused by:

• There is too much food in the chamber or the food stored contains too much water, resulting in heavy defrosting.
• The doors are not closed properly, resulting in frosting due to the entry of air and increased water due to defrosting.

Heat dissipation of the built-in condenser via the housing of the SUMMIT APPLIANCE FFRF106PL is normal. When the housing becomes hot due to high ambient temperatures and the storage of too much food, it is recommended to provide sound ventilation to facilitate heat dissipation.

Condensation on the exterior surface and door seals of the SUMMIT APPLIANCE FFRF106PL is normal when the ambient humidity is too high. Just wipe the condensate with a clean towel.

Abnormal noises considered normal for the SUMMIT APPLIANCE FFRF106PL include:

• Buzz: The compressor may produce a buzzing noise during operation, and the buzzes are loud particularly upon start or stop. This is normal.
• Creak: Refrigerant flowing inside of the appliance may produce a creaking sound, which is normal.