STIHL SHE 81 (01) PDF MANUAL

STIHL SHE 81 (01) PDF SUMMARY:

What should I do before performing any work on the machine?

Disconnect the plug from the wall outlet before performing any work on the machine, e.g., cleaning, maintenance, replacing parts.

---

What should I do before each use of the power tool?

Before each use, check that your power tool is in good condition. Pay special attention to the power cord, mains plug, and safety devices. Do not operate your power tool if any of its components are damaged.

---

What should I do before starting work with the power tool?

Inspect the power tool. The trigger switch/switch lever must move easily to STOP or 0. The trigger/switch lever must be on STOP or 0. The blower tubes must be properly assembled. Handles must be clean and dry, free from oil and dirt, for safe control. Check the condition of the blower wheel and blower housing.

---

What should I check regarding the electrical connection?

The voltage and frequency of the power tool and the power supply must be the same. Check the connecting cord, plug, and extension cord for damage. Always connect the power tool to a properly installed wall outlet. Check that the insulation of the power cord, extension cord, plug, and coupling is in good condition. Never touch the mains plug, connecting cord, extension cord, or electrical connections with wet hands.

---

How should I position the connecting and extension cords?

Check the minimum cross-section of wires. Position and mark the connecting cord so that it cannot be damaged or endanger others. Use only extension cords approved for outdoor use. The plug and coupling of the extension cord must be waterproof. Do not chafe on edges, pointed or sharp objects. Do not squeeze through gaps in doors or windows. If cords are twisted, unplug the power tool and straighten them out. Always unwind the extension cord completely from the cable drum to reduce the risk of fire from overheating.

---

How do I hold and control the power tool?

The blower is designed for one-handed operation, and it can be carried by the control handle in either the right or left hand. Always hold the power tool firmly in your hand. Operate the unit only with a properly mounted blower tube. Always switch off the motor and disconnect the plug from the power supply before removing the intake screen, suction tube, blower tube or elbow. Wait for the blower wheel to come to a complete standstill. The vacuum shredder is designed for two-handed operation. Hold and operate the power tool with your right hand on the control handle and your left hand on the assist handle. Wear the catcher bag shoulder strap over your right shoulder. Operate the power tool only with a properly mounted suction tube and closed catcher bag.

---

What should I do if the blower wheel or elbow is blocked?

Switch off the motor and disconnect the plug from the power supply. Remove the elbow and suction tube. Clean the elbow and blower housing.

---

What should I do with the power supply cord during operation?

Avoid damage to the power supply cord. Do not drive over it, pinch, or tug it. Never jerk the connecting cord to disconnect it from the wall outlet. To unplug, grasp the plug, not the cord.

---

What should I do in case of imminent danger or in an emergency?

Move the switch lever/trigger switch to STOP or 0.

---

What should I do before leaving the power tool unattended?

Switch it off and disconnect the plug from the power supply.

---

What should I do after finishing work?

Disconnect the plug from the wall outlet. Never jerk the connecting cord to disconnect it from the wall outlet. To unplug, grasp the plug, not the cord. Always clean dust and dirt off the power tool.

---

What are the steps for mounting the blower tube for the BGE 71 and BGE 81 models?

Line up the recesses. The arrow must be on the top of the blower tube. Push the blower tube into the blower housing stub as far as the stop. Push the union nut over the blower housing stub and turn it in the direction of the arrow until the tab engages the opening in the union nut. You will hear the safety switch being activated.

---

How do I mount the nozzle?

Push the nozzle onto the blower tube as far as lug, position (a) (long) or position (b) (short), and rotate the nozzle in the direction of the arrow to it lock in position.

---

How do I remove the blower tube?

Switch off the motor. Press down the lock button by inserting a suitable tool through the opening in the union nut. Rotate the union nut in the direction of arrow as far as the stop. Remove the blower tube.

---

How do I mount the elbow for the vacuum shredder?

Make sure the zipper on the catcher bag is closed. Push the elbow into the catcher bag as far as the mark. Tighten strap on catcher bag and press down the buckle tab. Line up the recesses. Push the elbow into the blower housing stub as far as the stop. Push the union nut over the blower housing stub and turn it in the direction of the arrow as far as the stop. You will hear the safety switch being activated.

---

How do I assemble the suction tube?

Line up the arrows on the suction tube and extension tube. Push together and lock in position.

---

How do I mount the suction tube?

Switch off the motor. Press down the lock button by inserting a suitable tool through the opening. Push lug against blower housing and hold it there. Rotate the intake screen in the direction of arrow as far as the stop and lift it away. Line up the arrows. Push the suction tube into the intake opening as far as the stop. Push the handle over the intake opening. Line up the arrows. Rotate the handle in the direction of the arrow until the lever engages audibly on the blower housing. The lock button must engage in position.

---

How do I remove the elbow?

Shut off the engine. Press down the lock button by inserting a suitable tool through the opening. Rotate the union nut in the direction of the arrow as far as the stop. Remove the elbow.

---

How do I remove the suction tube?

Shut off the engine. Press down the lock button by inserting a suitable tool through the opening. Depress lever and rotate handle in the direction of the arrow as far as the stop. Remove the handle together with the suction tube. Position the intake screen on the intake opening. Line up the arrows. Rotate the intake screen in the direction of the arrow until the lug engages audibly on the blower housing. Lock button must engage in position.

---

What is the minimum fuse protection for the power connection?

The minimum fuse protection of the power connection must comply with the specifications.

---

What type of circuit breaker is required?

The machine must be connected to the power supply via an earth-leakage circuit breaker to disconnect the power supply if the differential current to earth exceeds 30 mA.

---

What are the minimum cross-sections for extension cord wires?

• 220 V – 240 V: Up to 20 m – 1.5 mm2, 20 m to 50 m – 2.5 mm2
• 100 V – 127 V: Up to 10 m – AWG 14 / 2.0 mm2, 10 m to 30 m – AWG 12 / 3.5 mm2

---

How do I use the strain relief for the cord?

Insert the plug into the extension cord coupling. Make a loop in the extension cord. Pass the loop through the opening. Slip the loop over the hook and pull it tight.

---

How do I connect to a wall outlet?

Make sure the machine is switched off before you connect it to the power supply. Connect the extension cord plug to a properly installed wall outlet. Make sure you have a secure and balanced footing. Hold the unit in the normal working position.

---

How do I switch on the BGE 61, BGE 71, and SHE 71 models?

Move the switch to I or II (position II depends on the model). For units with a single switch setting (I): I = full power. For units with two switch settings (I and II): I = half power, II = full power.

---

How do I switch on the BGE 81 and SHE 81 models?

Squeeze the trigger switch on the control handle. Blowing and suction power are infinitely variable. Press in the lock button to lock the trigger switch in the maximum power position in the blower and vacuum modes.

---

How do I switch off the BGE 61, BGE 71, and SHE 71 models?

Move the switch to 0.

---

How do I switch off the BGE 81 and SHE 81 models?

Release the trigger switch on the control handle. If the lock button is engaged, squeeze the trigger switch briefly and let it go.

---

Where should I store the machine?

Store the machine in a dry, high or locked location, out of the reach of children and other unauthorized persons.

---

What is the maintenance schedule for the power tool?

	before starting work	after finishing work or daily	weekly	monthly	yearly	if problem	if damaged	if required
Complete machine (visual inspection)	x					x	x
Clean		x		x
Control handle (check operation)	x					x
Cooling inlets (clean)			x
Safety labels (replace)					x		x

---

What are the parts subject to wear and tear?

• Fanwheel
• Catcher bag