STAIRVILLE TINYBRIGHT IP A10 (01) PDF Document

This device is intended for use as a moving light effect with RGB+UV mixing. The device is designed for professional use in event technology, e.g. on stages, in theatres, discos, clubs, etc. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.

This device is intended for professional use only. The STAIRVILLE TINYBRIGHT IP A10 is not suitable for household use. Installation and commissioning should only be carried out by qualified personnel. Read the safety instructions carefully before operating the device.

DANGER! Danger for children: Ensure that plastic bags, packaging, etc. are properly disposed of and not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children unattended use electrical devices.

DANGER! Danger to life due to electric shock: Do not operate the device if it has visible damage. Do not switch on the device immediately after it has been exposed to temperature fluctuations (for example, after transport). Protect the STAIRVILLE TINYBRIGHT IP A10 from rain or moisture. Only plug the device into a properly wired mains socket. Do not attempt to bypass the fuse or replace it with a different type. Never touch the power cable with wet hands. Unplug the device from the mains socket immediately if you notice any signs of malfunction. Disconnect the device from the mains when cleaning it or when it is not in use. Always pull the plug from the mains cable, not the cable itself. Never modify the STAIRVILLE TINYBRIGHT IP A10.

CAUTION! Danger of burns: The surfaces of the STAIRVILLE TINYBRIGHT IP A10 can become hot during operation. Allow the device to cool down sufficiently before handling it.

CAUTION! High volume levels: Continuous exposure to high volume levels can lead to hearing damage. Take breaks regularly and wear appropriate hearing protection when exposed to high volume levels.

NOTICE! Fire hazard: Do not block the STAIRVILLE TINYBRIGHT IP A10’s ventilation openings. Do not place the device near any direct heat source. Keep the STAIRVILLE TINYBRIGHT IP A10 away from open flames.

NOTICE! Operating conditions: The STAIRVILLE TINYBRIGHT IP A10 has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specified in the ‘Technical specifications’ chapter. Avoid heavy jolts and shocks to the device.

NOTICE! Power supply: Before connecting the STAIRVILLE TINYBRIGHT IP A10, ensure that the input voltage (AC 100-240 V ~ 50/60 Hz) matches the mains voltage. Do not unplug the STAIRVILLE TINYBRIGHT IP A10 from the mains during operation. Otherwise, parts of the device may be damaged. When the device is not used for a longer period of time, disconnect it from the mains to prevent damage from overvoltage. Ensure that the power supply cable is not trapped in any way. Never route the power cable over sharp edges or hot parts.

NOTICE! Possible staining: The plasticizer contained in the rubber feet of this product may react with the coating of your parquet, linoleum, laminate, or PVC floor and cause permanent dark stains in some cases. If necessary, put suitable felt pads under the rubber feet or place the device on a carpet or non-staining base.

NOTICE! Risk of property damage: When disconnecting the mains plug, always pull on the plug and not on the cable. In order to prevent damages to the STAIRVILLE TINYBRIGHT IP A10 during transport and storage, the device should always be transported in the original box or in a suitable transport case.

Connect the STAIRVILLE TINYBRIGHT IP A10 to the mains using the supplied power cable. You can control the STAIRVILLE TINYBRIGHT IP A10 via DMX or operate it in Master/Slave mode. If you do not use DMX, set the first STAIRVILLE TINYBRIGHT IP A10 to Master mode and connect its DMX output to the DMX input of the next STAIRVILLE TINYBRIGHT IP A10. This STAIRVILLE TINYBRIGHT IP A10 is then the first slave. When all STAIRVILLE TINYBRIGHT IP A10s are connected, set all subsequent STAIRVILLE TINYBRIGHT IP A10s to Slave mode.

The STAIRVILLE TINYBRIGHT IP A10 can be controlled via DMX or operated in Master/Slave mode. The device can be operated in various modes: DMX mode, Master/Slave mode, Auto mode, and Sound mode.

The STAIRVILLE TINYBRIGHT IP A10 is operated via four buttons and an LCD screen. The display functions are:

The STAIRVILLE TINYBRIGHT IP A10 has the following menu options:

1. Press [MENU] to enter the main menu.

2. Select ‘DMX Address’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to select a DMX start address (001 – 512).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘DMX Channel mode’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to select the DMX channel mode (4CH/6CH/8CH).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Slave mode’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to select the slave mode (SLA1/SLA2).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Sound mode’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to switch the Sound mode on or off.

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Auto mode’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to select an automatic mode program (AUTO1 – AUTO8).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Fade mode’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to select an automatic fade program (Fade1 – Fade8).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Strobe Speed’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to set the strobe speed (0 = no strobe, 9 = maximum strobe).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Dimmer mode’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to set the dimming curve (0 – 10).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Display Reverse’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to reverse the display orientation.

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Display Backlight’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to set the brightness of the display backlight (0 – 100).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘LED Display Off Time’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Use [UP] and [DOWN] to set the time in seconds after which the display backlight turns off (0 – 60).

5. Confirm your selection with [ENTER].

1. Press [MENU] to enter the main menu.

2. Select ‘Software Version’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER]. The current software version will be shown.

1. Press [MENU] to enter the main menu.

2. Select ‘Reset’ with [UP] and [DOWN].

3. Confirm your selection with [ENTER].

4. Select ‘RSET’ with [UP] and [DOWN].

5. Confirm your selection with [ENTER]. The device will restart with factory settings.

Clean the STAIRVILLE TINYBRIGHT IP A10 regularly to remove dirt and dust from the inside and outside. Use a soft, damp cloth for the exterior. Only use neutral cleaning agents. Clean the device and especially the light exit openings from dust and dirt at regular intervals. Dust in the interior can be removed with a vacuum cleaner or an air compressor. For cleaning the optical lenses, use a soft, dry cloth. Always disconnect the device from the mains before cleaning.

If the STAIRVILLE TINYBRIGHT IP A10 is not working, first check the mains connection. If the device is connected to the mains, but no light effect is produced, try setting the device to a different operating mode (e.g. Master/Slave or Auto mode). If the device still does not work, disconnect it from the mains and consult a qualified technician.