ST SPC58XXADPT176S (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD ST SPC58XXADPT176S (01) PDF MANUAL


PDF Content Summary: UM2723 User manual UM2723 - Rev 1 - June 2020 For further information contact your local STMicroelectronics sales office. st.com

SPC58XXADPT176S Rev.B evaluation board Introduction The SPC58XXADPT176S Rev.B evaluation board supports STMicroelectronics SPC58EE84E7, SPC58NE84E7, SPC58XN8XE7 and SP58xG8xE7 microcontroller in LQFP 176 24x24x1.4 package with exposed pad down. Figure 1. SPC58XXADPT176S Rev. B UM2723 Overview 1 Overview The SPC58XXADPT176S Rev. B mini module is an evaluation board supporting STMicroelectronics SPC58EE84L7, SPC58NE84E7, SPC58XN8XE7 and SP58xG8xE7 microcontrollers in LQFP 176 24x24x1.4 package with exposed pad down. This mini module is designed to be connected onto the SPC58XXMB motherboard, offering a mechanism for easy customer evaluation of the supported devices, and to facilitate hardware and software development. The mini module may be used as a stand-alone unit allowing access to the CPU, but not to access to the I/O pins nor any motherboard peripherals. By default, the mini module is configured for SPC58EE84E7/SPC58NE84E7, easily supports SPC58XN8XE7 and SPC58xG8xE7 simply changing the following through hole jumpers: J44, J45, J46 and J47. 1.1 Package contents An SPC58XXADPT176S Rev. B adapter package includes the following item: • SPC58XXADPT176S Rev. B mini module 1.2 Supported devices The SPC58XXADPT176S Rev. B mini module supports the following STMicroelectronics family of microcontrollers in LQFP 176 24x24x1.4 package with exposed pad down: • SPC58EE84E7/SPC58NE84E7 • SPC58XN8XE7 • SPC58xG8E7 UM2723 - Rev 1 page 2/28 UM2723 License agreement 2 License agreement The packaging of this evaluation board was sealed with a seal stating, “by breaking this seal, you agree to the terms and conditions of the evaluation board license agreement, the terms and conditions of which are available at st.com/ebla”. Upon breaking the seal, you and STMicroelectronics entered into the evaluation board license agreement, a copy of which is also enclosed with the evaluation board for convenience. Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use with other products and is not suitable for any safety or other commercial or consumer application. This evaluation board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or implied, including the implied warranties of merchantability and fitness for a particular purpose. UM2723 - Rev 1 page 3/28 UM2723 Handling precautions 3 Handling precautions Please take care to handle the package contents in a manner such as to prevent electrostatic discharge. Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage. UM2723 - Rev 1 page 4/28 UM2723 Hardware description 4 Hardware description 4.1 Hardware features The SPC58XXADPT176S Rev. B mini module board has the following features: • Connector for external power supplies input (5 V, 3.3 V, 1.25 V) used in stand-alone mode • Reset button with driver and led indicator • Socket for device in LQFP 176 24x24x1.4 package with exposed pad down • Debug interfaces: – 14-pin header connector for JTAG interface – 10-pin header connector for JTAG/LFAST LVDS interface – 10-pin header connector for SIPI interface • 40 MHz crystal main oscillator with jumpers to optionally disconnect it • 8 MHz oscillator with jumpers to optionally disconnect it • Clock input through SMA connector to optionally disconnect it • Predisposed for SMPS regulator module • 2 X Samtec QSH series, 240 way connector to connect mini module to Motherboard UM2723 - Rev 1 page 5/28 UM2723 Hardware dimension 4.2 Hardware dimension The mini module has the following dimensions: • PCB area: 127 mm x 114.3 mm • Top components height: 19 mm max • Bottom components height: 3.5 mm max • PCB thickness: 1.6 mmFigure 2. SPC58XXADPT176S Rev. B top component view UM2723 - Rev 1 page 6/28 UM2723 Power and system configuration 5 Power and system configuration 5.1 Power supplies The mini module can be powered by providing the three voltages (5 V, 3.3 V and 1.25 V) or supplied externally by the 4 pins connector (J5) or supplied by the motherboard. When the mini module is plugged onto the motherboard, power is supplied directly by the motherboard. In this setup, the external power supply input available on the mini module should NOT be used. When the SPC58XXADPT176S Rev. B mini module is used as a stand-alone board, external power supplies must be used (5 V, 3.3 V, 1.25 V). The following jumpers are used to configure the power supply (common for all supported devices): Table 1. Power configuration jumpers Jumper Description Default VDD_HV_ADR voltage configuration: J1 • 1-2 5.0V_LR • 2-3 3.3V_SR UM2723 - Rev 1 page 7/28 1-2 (5.0V_LR) J2 VDD_HV_ADV voltage configuration: • 1-2 5.0V_LR • 2-3 3.3V_SR 1-2 (5.0V_LR) J3 VDD_HV_IO_JTAG voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) J6 VDD_HV_IO_MAIN voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) J7 VDD_HV_IO_FLEX voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) J38 Device pin 153 EXTREG_SEL function configuration: • 2-1 Reserved for STMicroelectronics • 2-3 ENABLED BALLAST • 2-4 DISABLE BALLAST 2-4 (DISABLE BALLAST) J39 Supply for BALLAST circuit configuration • 1-2 VDD_HV_IO_MAIN • 2-3 5.0V_SR 1-2 (VDD_HV_IO_MAIN) J40 VDD_LV voltage configuration: • 2-1 (BALLAST circuit) • 2-3 (1.25V_SR) • 2-4 (SMPS regulator module) Do not use this configuration for SP58xG8xE7 2-3 (1.25V_SR) J43 Device pin 155 VDD_HV_FLA voltage configuration: • OPEN – disconnect VDD_HV_FLA from VDD_HV_IO_MAIN • CLOSED - connect VDD_HV_FLA from VDD_HV_IO_MAIN Closed (connect pin 155 VDD_HV_FLA to VDD_HV_IO_MAIN) UM2723 JTAG/LFAST LVDS interface configuration 5.2 JTAG/LFAST LVDS interface configuration The following jumpers need to configure the JTAG/LFAST LVDS: Table 2. LFAST configuration jumpers Jumper Description Default JTAG/LFAST LVDS pin 9 configuration J41 • 1-2: EVTO • 2-3: ESR0 UM2723 - Rev 1 page 8/28 1-2 (EVTO) J42 JTAG/LFAST LVDS pin 10 configuration • 1-2: PORST • 2-3: ESR0 1-2 (PORST) 5.3 System clock configuration The mini module supports the usage of crystal clock sources as well as external clock source: Table 3. Clock configuration jumpers Jumper Description Default J21 EXTAL configuration • 1-2 pin 2 of 40 MHz crystal (Y1) • 2-3 EVB-EXTAL 1-2 (XT1 pin2) J23 XTAL configuration • 1-2 pin 1 of 40 MHz crystal (Y1) • 2-3 GND 1-2 (XT1 pin1) J22 Enable 8 MHz oscillator power supply • Open – power off • Closed – power on Open (power off) J24 External 8 MHz clock source • 1-2 OSC-MOD (from oscillator) • 2-3 EXTAL-SMA (from SMA connector) 1-2 (8 MHz from oscillator) UM2723 Reset circuit 5.4 Reset circuit The mini module supports different ways to reset the microcontroller. To use and perform the reset driving there are different jumpers and switches: Table 4. Reset configuration jumpers Jumper Description Default SW1 Reset push button Open J27 Connect the external reset to the reset driver for ESR0 and PORST pins Close J25 Connect the external reset to ESR0 pin Close J26 Connect the external reset to PORST pin Close 5.5 Other jumpers Table 5. Other jumpers Jumper Description Default VDD_HV_PMC voltage configuration: J4 • 1-2 5.0V_SR • 2-3 3.3V_SR UM2723 - Rev 1 page 9/28 1-2 (5.0V_SR) J30 TESTMODE settings Close (10 KΩ down) 5.6 Configuration for SPC58EE84E7/SPC58NE84E7 (default configuration) To configure the board for SPC58EE84E7/SPC58NE84E7 set the jumpers described in the table below. Table 6. SPC58EE84E7/SPC58NE84E7 configuration jumpers (default configuration) Jumper Description Default J44 Device pin 10 port configuration • 1-2 PL8 • 2-3 VDD_LV_BD 1-2 (PL 8) J45 Device pin 154 function configuration • OPEN – disconnect BCTRL with ballast circuit • CLOSED – connect BCTRL with ballast circuit Closed (connect BCTRL with BALLAST circuit) J46 Device pin 79 configuration • 1-2 PB10 (GPIO) • 2-3 VDD_LV_BD (1.25V) 1-2 (PB10) J47 Device pin 59 configuration • 1-2 PE15 (GPIO) • 2-3 VDD_HV_IO_MAIN 1-2 (PE15) UM2723 Configuration for SPC58EE84E7/SPC58NE84E7 5.7 Configuration for SPC58EE84E7/SPC58NE84E7 To configure the board for SPC58EE84E7/SPC58NE84E7 set the jumpers described in the table below. Table 7. SPC58EE84E7/SPC58NE84E7 configuration jumpers Jumper Description Default

Device pin 10 port configuration 1-2 J44 1-2 PL8 2-3 VDD_LV_BD 1-2 1-2 (PL 8) (PL 8)

UM2723 - Rev 1 page 10/28

J45 Device pin 154 function configuration • OPEN – disconnect BCTRL with ballast circuit • CLOSED – connect BCTRL with ballast circuit Closed Closed (connect BCTRL with BALLAST circuit) (connect BCTRL with BALLAST circuit) J46 Device pin 79 configuration • 1-2 PB10 (GPIO) 1-2 (PB10) 1-2 (PB10) • 2-3 VDD_LV_BD (1.25V) J47 • 1-2 PE15 (GPIO) 2-3 (VDD_HV_IO_BD) 2-3 (VDD_HV_IO_BD)

Device pin 59 configuration • 2-3 VDD_HV_IO_MAIN 5.8 Configuration for SPC58XN8XE7 To configure the board for SPC58XN8XE7 set the jumpers described in the table below. Table 8. SPC58XN8XE7 configuration jumpers Jumper Description Configuration

J44 Device pin 10 port configuration 1-2 PL8 2-3 VDD_LV_BD 1-2 1-2 (PL 8) (PL 8) J45 Device pin 154 function configuration • OPEN – disconnect BCTRL with ballast circuit • CLOSED – connect BCTRL with ballast circuit Open Open (device pin 154 not connected) (device pin 154 not connected) J46 Device pin 79 configuration • 1-2 PB10 (GPIO) 1-2 (PB10) 1-2 (PB10) • 2-3 VDD_LV_BD (1.25V) J47 • 1-2 PE15 (GPIO) 1-2 (PE15) 1-2 (PE15)

Device pin 59 configuration • 2-3 VDD_HV_IO_MAIN UM2723 Configuration for SPC58XN8XE7 ED 5.9 Configuration for SPC58XN8XE7 ED To configure the board for SPC58XN8XE7 set the jumpers described in the table below. Table 9. SPC58XN8XE7 ED configuration jumpers Jumper Description Configuration

Device pin 10 port configuration 2-3 J44 1-2 PL8 2-3 VDD_LV_BD 2-3 2-3 (VDD_LV_BD) (VDD_LV_BD)

UM2723 - Rev 1 page 11/28

J45 Device pin 154 function configuration • OPEN – disconnect BCTRL with ballast circuit • CLOSED – connect BCTRL with ballast circuit Open Open (device pin 154 not connected) (device pin 154 not connected) J46 Device pin 79 configuration • 1-2 PB10 (GPIO) 2-3 (VDD_LV_BD) 2-3 (VDD_LV_BD) • 2-3 VDD_LV_BD (1.25V) J47 • 1-2 PE15 (GPIO) 2-3 (VDD_HV_IO_BD) 2-3 (VDD_HV_IO_BD)

Device pin 59 configuration • 2-3 VDD_HV_IO_MAIN 5.10 Configuration for SP58xG8xE7 To configure the board for SP58xG8xE7 set the jumpers described in the table below. Table 10. SP58xG8xE7 configuration jumpers Jumper Description Configuration

J44 Device pin 10 port configuration • 1-2 PL8 • 2-3 VDD_LV_BD 1-2 1-2 (connect pin 10 to PL 8) (connect pin 10 to PL 8) J45 Device pin 154 function configuration • OPEN – disconnect BCTRL with ballast circuit • CLOSED – connect BCTRL with ballast circuit Closed Closed (connect BCTRL with BALLAST circuit) (connect BCTRL with BALLAST circuit) J46 Device pin 79 configuration • 1-2 PB10 (GPIO) 1-2 (PB10) 1-2 (PB10) • 2-3 VDD_LV_BD (1.25V) J47 • 1-2 PE15 (GPIO) 1-2 (PE15) 1-2 (PE15)

Device pin 59 configuration • 2-3 VDD_HV_IO_MAIN UM2723 Hardware description 6 Hardware description 6.1 Jumpers The following table describes all the jumpers of the mini module, their default configuration and their position on PCB. Table 11. Jumpers Jumper Description Default Position J1 UM2723 - Rev 1 page 12/28 VDD_HV_ADR voltage configuration: • 1-2 5.0V_LR • 2-3 3.3V_SR 1-2 (5.0V_LR) Figure 1. SPC58XXADPT176S Rev. B - C2 J2 VDD_HV_ADV voltage configuration: • 1-2 5.0V_LR • 2-3 3.3V_SR 1-2 (5.0V_LR) Figure 1. SPC58XXADPT176S Rev. B - C2 J3 VDD_HV_IO_JTAG voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) Figure 1. SPC58XXADPT176S Rev. B - B2 J4 Reserved for STMicroelectronics VDD_HV_PMC voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) Figure 1. SPC58XXADPT176S Rev. B - B2 J6 VDD_HV_IO_MAIN voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) Figure 1. SPC58XXADPT176S Rev. B - B2 J7 VDD_HV_IO_FLEX voltage configuration: • 1-2 5.0V_SR • 2-3 3.3V_SR 1-2 (5.0V_SR) Figure 1. SPC58XXADPT176S Rev. B - B2 J13 PF[15]/EVTI connection to QSH motherboard connectors Not mounted Figure 1. SPC58XXADPT176S Rev. B - A2 J21 EXTAL configuration • 1-2 pin 2 of 40 MHz crystal (Y1) • 2-3 EVB-EXTAL (XT1 1-2 pin2) Figure 1. SPC58XXADPT176S Rev. B - C3 J22 Enable 8 MHz oscillator power supply • open – power off • closed – power on Open (power off) Figure 1. SPC58XXADPT176S Rev. B - D3 J23 XTAL configuration • 1-2 pin 1 of 40 MHz crystal (Y1) • 2-3 GND (XT1 1-2 pin1) Figure 1. SPC58XXADPT176S Rev. B - C3 J24 External 8 MHz clock source • 1-2 OSC-MOD (from oscillator) • 2-3 EXTAL-SMA (from SMA connector) 1-2 (8 MHz from oscillator) Figure 1. SPC58XXADPT176S Rev. B - D3 J25 Connect the external reset to ESR0 pin Close Figure 1. SPC58XXADPT176S Rev. B - D2 J26 Connect the external reset to PORST pin Close Figure 1. SPC58XXADPT176S Rev. B - D2 J27 Connect the external reset to the reset driver for ESR0 and PORST pins Close Figure 1. SPC58XXADPT176S Rev. B - D1 J30 Testmode settings Close (10 KΩ down) Figure 1. SPC58XXADPT176S Rev. B - B2 UM2723 Jumpers Jumper Description Default Position J31 PH[11]/EVTO connection to QSH motherboard connectors Not mounted Figure 1. SPC58XXADPT176S Rev. B - A2 J38 UM2723 - Rev 1 page 13/28 Device pin 153 EXTREG_SEL function configuration: • 2-1 Reserved for ST • 2-3 ENABLED BALLAST • 2-4 DISABLE BALLAST (DISABLE 2-4 BALLAST) Figure 1. SPC58XXADPT176S Rev. B - B2 J39 Supply for BALLAST circuit configuration • 1-2 VDD_HV_IO_MAIN • 2-3 5.0V_SR 1-2 (VDD_HV_IO_MAIN) Figure 1. SPC58XXADPT176S Rev. B - A2 J40 VDD_LV voltage configuration: • 2-1 (BALLAST circuit) • 2-3 (1.25V_SR) • 2-4 (SMPS regulator module) 2-3 (1.25V_SR) Figure 1. SPC58XXADPT176S Rev. B - A3 J41 JTAG/LFAST LVDS pin 9 configuration • 1-2: EVTO • 2-3: ESR0 1-2 (EVTO) Figure 1. SPC58XXADPT176S Rev. B - A3 J42 JTAG/LFAST LVDS pin 10 configuration • 1-2: PORST • 2-3: ESR0 1-2 (PORST) Figure 1. SPC58XXADPT176S Rev. B - A3 J43 Device pin 155 VDD_HV_FLA voltage configuration: • OPEN - disconnect VDD_HV_FLA from VDD_HV_IO_MAIN • CLOSED - connect VDD_HV_FLA from VDD_HV_IO_MAIN Closed (connect pin 155 VDD_HV_FLA to VDD_HV_IO_MAIN) Figure 1. SPC58XXADPT176S Rev. B - B2 J44 Device pin 10 port configuration / function configuration • 1-2 PL8 • 2-3 VDD_LV_BD 1-2 (connect pin 10 to PL 8) Figure 1. SPC58XXADPT176S Rev. B - B4 J45 Device pin 154 function configuration • OPEN - disconnect BCTRL with ballast circuit • CLOSED - connect BCTRL with ballast circuit Closed (connect BCTRL with BALLAST circuit) Figure 1. SPC58XXADPT176S Rev. B - A3 J46 Device pin 79 configuration (SUPPLY/GPIO) • 1-2 pin 79 configured as GPIO (PB10) • 2-3 VDD_LV_BD (1.25V_SR) 1-2 (PB10) Figure 1. SPC58XXADPT176S Rev. B - C2 J47 Device pin 59 configuration (SUPPLY/GPIO) • 1-2 pin 59 configured as GPIO (PE15) • 2-3 pin 59 configured as supply (VDD_HV_IO_MAIN) 1-2 (PE15) Figure 1. SPC58XXADPT176S Rev. B - C4 SW1 Reset push button Open Figure 1. SPC58XXADPT176S Rev. B - D1 UM2723 Test points 6.2 Test points The mini module has several test points, described in the table below. Table 12. Test points Test point Description Position GT1, GT2, GT3, GT4, GT5 GND test point TP1 VSS_OSC test point Figure 1. SPC58XXADPT176S Rev. B - D3 TP2 AGND test point Figure 1. SPC58XXADPT176S Rev. B - D3 TP3 JCOMP_RxDATA_N test point Figure 1. SPC58XXADPT176S Rev. B - A3 TP4 TCK test point Figure 1. SPC58XXADPT176S Rev. B - A2 TP5 TMS_TxDATA_P test point Figure 1. SPC58XXADPT176S Rev. B - A3 TP6 TDI_TxDATA_N test point Figure 1. SPC58XXADPT176S Rev. B - A3 TP7 TDO_RxDATA_P test point Figure 1. SPC58XXADPT176S Rev. B- A3 TP9 SIPI_RXN test point Figure 1. SPC58XXADPT176S Rev. B - C2 TP11 SIPI_TXN test point Figure 1. SPC58XXADPT176S Rev. B - C2 TP13 SIPI_RXP test point Figure 1. SPC58XXADPT176S Rev. B - C2 TP15 SIPI_TXP test point Figure 1. SPC58XXADPT176S Rev. B - C2 TP22 J16A, QSH connector, pin10 (PA5) test point Figure 1. SPC58XXADPT176S Rev. B - A4 TP23 J16A, QSH connector, pin14 (PA9) test point Figure 1. SPC58XXADPT176S Rev. B - B4 TP24 J16A, QSH connector, pin19 (PA14) test point Figure 1. SPC58XXADPT176S Rev. B - A4 TP25 J16A, QSH connector, pin12 (PA7) test point Figure 1. SPC58XXADPT176S Rev. B - B4 TP26 J16A, QSH connector, pin13 (PA8) test point Figure 1. SPC58XXADPT176S Rev. B - A4 TP27 J17B, QSH connector, pin209 (PD7) test point Figure 1. SPC58XXADPT176S Rev. B - D1 TP28 J16A, QSH connector, pin11 (PA6) test point Figure 1. SPC58XXADPT176S Rev. B - A4 TP29 J17B, QSH connector, pin210 (PD6) test point Figure 1. SPC58XXADPT176S Rev. B - D1 TP30 J17B, QSH connector, pin183 (PF13) test point Figure 1. SPC58XXADPT176S Rev. B - C1 UM2723 - Rev 1 page 14/28 UM2723 Connectors 6.3 Connectors The mini module has the following connectors:Table 13. Connectors Connectors Description J18 14-pin header connector for JTAG interface CN1 10-pin header connector for JTAG/LFAST LVDS interface J20 10-pin header connector for SIPI interface J36, J37 SMPS regulator module J16, 17 2 X Samtec QSH series, 240 way connector to connect mini module to Motherboard J5 External power supplies input (5 V, 3.3 V, 1.25 V) P1 SMA connector for external clock Input Figure 3. Overview of SPC58XXADPT176S Rev. B mini module - top UM2723 - Rev 1 page 15/28 UM2723 Connectors UM2723 - Rev 1 page 16/28 Figure 4. Overview of SPC58XXADPT176S Rev. B mini module - bottom UM2723 BOM 7 BOM Table 14. BOM Qty Ref. designator Value Description Manufacturer Manufcode 1 CN1 Samtec TFM-105-02-L-D-WT UM2723 - Rev 1 page 17/28 Conn TFM 10 pin, with weld Tabs Samtec TFM-105-02-L-D-WT 13 C1, C3, C5, C7, C10, C16, C18, C20, C22, C24, C58, C103, C122 100 nF Mult. cer. cap. 16 C2, C4, C6, C8, C11, C17, C19, C21, C23, C25, C33, C39, C42, C45, C48, C104 10 nF Mult. cer. cap. 1 C9 DNM Mult. cer. cap. 5 C14, C15, C100, C101, C102 4.7 uF Mult. cer. cap. 1 C28 1 uF Mult. cer. cap. 1 C29 DNM Mult. cer.cap. 5 C32, C38, C41, C44, C47 47 nF Mult. cer. cap. 5 C34, C40, C43, C46, C49 2.2 uF Mult. cer.cap. 4 C56, C57, C132, C133 DNM Mult. cer. cap. 3 C121, C125, C127 2.2 uF Mult. cer. cap. 4 C123, C124, C126, C128 DNM Mult. cer. cap. 1 C134 27 pF Mult. cer. cap. 1 D1 Yellow Led diode yellow Agilent HSMY-C150 1 D4 Red Led diode red Agilent HSMS-C150 7 TP1, GT1, TP2, GT2, GT3, GT4, GT5 TEST1-SMD SMD PCB test point 3 J1, J2, J3, J4, J6, J7, J21, J23, J24, J39, J41, J44, J46, J47, J42 Strip male 20 pin, 1 row , STRIP3-2MM 180° Harwin M22-2512005 see match parts 1 J5 METZ 31072104 CONN Metz Connect 4 poli 16A 31072104 Metz Connect 31072104 Yamaichi UM2723 BOM Qty Ref. designator Value Description Manufacturer Manufcode 2 J13, J31 DNM Strip male 2 pin, 1 row , 180° Harwin M22-2512005 2 J16, J17 Samtec QSH-120-01-L- D-A IC357-1764-168P-2 1 U2 8 MHz Clock oscillator ECS ECS-3953M-080-BN- TRUM2723 - Rev 1 page 18/28 Samtec 0.5 mm pitch high speed socket Samtec SAM-QSH12001LDA 1 J18 N2514-6002RB Conn flat male 14 pin, 180° 3M N2514-6002RB 1 J20 ERF8-005-05.0-L-DV-L- TR Conn rugged female 10 pin, high speed Samtec ERF8-005-05.0-L- DV-L-TR 1 J25, J26, J27, Strip J30, J43, J45, male 20 pin, 1 row , STRIP2-2MM 180° Harwin M22-2512005 J22 see match parts 2 J36, J37 STRIP6 Male strip 36 pins pitch 2.54 180° Preci-dip 1 J38, J40 STRIP3+1PMD-2MM Strip mamle 20 pin, 1 row , 180° see match parts Harwin M22-2512005 1 P1 SMA-FEM-180 Coax conn female 5 pin, 180° Samtec SMA-J-P-H-ST-TH1 1 Q1 NJD2873T4G Trans. NPN plastic pow er ON Semiconductor NJD2873T4G 8 R1, R2, R7, R15, R18, R19, R21, R22 0R Resistor 2 R3, R26 DNM Resistor 3 R4, R9, R27 10K Resistor 8 R5, R6, R17, R20, R23, R24, R25, R28 DNM Resistor 1 R8 100R Resistor 2 R10, R12 560R Resistor 3 R11, R13, R14 4K7 Resistor 1 R16 DNM Resistor 1 SW1 Pushbutton NO B6110-0 Pushbutton NO B6110-0 low profile for pcb Delta Elettronica B6110-0 18 TP3, TP4, TP5, TP6, TP7, TP9, TP11, TP13, TP15, TP22, TP23, TP24, TP25, TP26, TP27, TP28, TP29, TP30 Test point Testpoint SMD - ignore 1 U1 Socket QFP Socket 176 QFP OPEN TOP Yamaichi IC357-1764-168P-2 UM2723 BOM Qty Ref. designator Value Description Manufacturer Manufcode 1 U3 74LVC125AMTR HCMOS buffer STMicroelectronics 74LVC125AMTR 1 U4 74V1G08STR CMOS AND gate STMicroelectronics 74V1G08STR 1 Y1 40 MHz Quartz NDK NX5032GA SPC58xxADPT176S EVB for 1 PCB SPC58EE84E7/ SPC58NE84E7 eTQFP176(A0A4) 24 UM2723 - Rev 1 page 19/28 J1, J2, J3, J4, J6, J7, J21, J23, J24, J39, J41, J44, J22, J25, J26, J27, J30, J43, J45, J46, J38, J40, J42, J47 Bridge 2 pins female 2 mm pitch Harwin H3161-05 8 Schematic Figure 5. Microcontroller pins TP3 TP4 TP5 TP6 TP7 U1B (pg6) PA[0..15] Socket QFP PB[0..15] (pg6) PA0 PA1 137 134 133 PA[0] PA[1] PA[2] PB[0] PB[1] PB0 PB1 PB[2] PB[3] JCOMP_RxDATA_N PB[4] PB[5] PB5 TMS_TxDATA_P PB[6] PB[7] PB[8] PB[9] PB[10] PB[11] PB[12] PB[13] PB[14] PB[15] PD[0..15] (pg6) 13 12 11 9 8 7 6 5 4 3 PC[0] PC[1] PC[2] PC[3] PC[4] PC[5] PC[6] PC[7] PC[8] PC[9] PF[0..15] (pg5,6) 14 15 16 19 20 67 66 PA2 65 64 61 36 46 45 81 80 79 78 PA12 135 136 PA[12] PA[13] 35 34 33 32 (pg6) PC[0..15] PC2 PE[0] PE[1] PE[2] PE[3] PE[4] EVTI (pg4) 62 60 59 PE[13] PE[14] PE[15] PH[0..15] (pg6) PH[0] PH[1] 140 141 37 38 39 40 41 42 47 48 22 23 73 72 71 70 105 106 PI[0] PI[1] PI[2] PI[3] PI[4] PI[5] PI[6] PI[7] PI[8] PI[9] PI[10] PI[11] PI[12] PI[13] PI[14] PI[15] PB2 PA3 PA4 82 PA[3] PA[4] PB3 120 (pg4) JCOMP_RxDATA_N (pg4) TCK TCK 114 115 PA[5] PA[6] PB9 PF[6] PF[7] 84 85 PJ[0] PJ[1] 86 87 PORST ESR0 122 121 PB4 STRIP3PMD-2MM(pg4) (pg4) (pg4) TMS_TxDATA_P TDI_TxDATA_N TDO_RxDATA_P TDI_TxDATA_N TDO_RxDATA_P 112 111 113 PA[7] PA[8] PA[9] SIPI_TXP PF[14] 116 PG1 PH[11] 117 TESTMODE 118 PB6 PB7 PB8 1 PB10 PB[0..15] (pg6) PA10 PA11 142 143 PA[10] PA[11] 2 PB11 PB12 3 SIPI TPs & off page PA13 PA15 110 88 PA[14] PA[15] PB13 PB14 PB15 J46 VDD_LV connector TP11 PC0 PC1 PC7 (pg6)PE[0..15] PD[0] PD[1] PD[2] PD[3] PD[4] PD[5] PD[6] PD[7] PD[8] PD[9] PD[10] PD[11] PD[12] PD[13] PD[14] PD[15] 159 158 157 156 129 130 109 108 83 76 77 63 17 18 1 2 PD5 SPC58xxADPT176S LQFP 176 24x24x1.4 SIPI_TXNPD0 PD1 TP15 SIPI_TXPPD12 TP13 SIGNALS (pg6)PG[0..15] PH[2] 144 EVTO (pg4) EVTO PH11 PH11 (pg6) (pg6) PI[0..15] PJ[2] 89 R27 10K SIPI_TXN(pg4) 21 28 29 30 31 43 44 49 50 55 56 57 58 124 125 138 PG[0] PG[1] PG[2] PG[3] PG[4] PG[5] PG[6] PG[7] PG[8] PG[9] PG[10] PG[11] PG[12] PG[13] PG[14] PG[15] PJ[0..4] (pg6) PORST(pg4,5) ESR0 (pg4,5) EXTAL(pg5) XTAL(pg5) GND POS-PIN-1 PD2 PC3 PC4 PC13 PD3 PD4 PC5 PC6 SIPI_TXN SIPI_TXP(pg4) PC8 SIPI_RXP PD8 TP9 PC9 PD9 PC10 PC11 167 166 165 PC[10] PC12 163 162 161 PC[11] PC[12] PC[13] PC[14] PC[15] PD10 PD11 SIPI_RXNSIPI_RXN (pg4) PD13 PC14 PD14 PC15 PD15 PF1 PE2 PE7 PF7 PF15 PH[15] 168 EXTAL XTAL SIPI_RXP PE0 PE1 SIPI_RXP PF[0] PF[1] 75 PF0 (pg4) 74 PF[2] PF[3] 174 173 PH[12] PH[13] 176 175 PF2 PE3 PF3 PE4 PF[4] PF[5] PF12 PE13 169 PF4 PE5 PE6 126 127 128 131 132 PE[5] PE[6] PE[7] PE[8] PE[9] 170 PF5 PF6 PE8 PF[8] 90 PE14 PH[14] 172 PJ[3] PJ[4] 91 92 PF8 PE9 PF[9] PF[10] PF[11] PF[12] PF[13] 95 96 97 98 107 PF9 STRIP3PMD-2MM PE10 145 146 PE[10] PE[11] PF10 1 PE11 PE12 160 PE[12] PH[3] PH3 PH[4] 147 148 PH[7] PH[8] PH[9] PH[10] 152 151 150 149 PF11 PE15 SIPI_RXN 2 PF[15] 119 PF14 EVTI 2 J13 1 3 DNM PH0 PH8 J31 DNM PH15 EXTAL XTAL 103 102 PF15 (pg6) VDD_HV_IO_MAIN PG0 J47 PG2 PH1 PH2 PG3 PG4 PH4 PG5 PG6 PG7 PH[5] PH[6] 93 94 PH5 PH6 PH7 PG8 PG9 PH9 PG10 PH10 PG11 EVTO 2 1 PG12 PH12 PG13 PH13 PG14 PH14 PG15 PI0 PI3 Port pins and reset signal are routed to motherboard. High speed signals are not J30 routed to mother board, but have test points to connect to test STRIP2PMD-2MM on mother board connector EVT signal are connected to optional jumper to be routed to mother board. PJ0 PI1 PJ1 PI2 PJ4 PI6 PJ2 PJ3 5.0V_SR PI4 PI5 PI7 PI11 PI15 PORST R26 PI8 ESR0 DNM PI9 PI10 DNP 2 1 PI12 PI13 PI14 178 Figure 6. JTAG, JTAG/LFAST LVDS interface, SIPI I/F and SMPS interface CONN JTAG interface JTAG/LFAST LVDS INTERFACE R25 DNM GND J37 STRIP 10 Pin Version C56 DNM Place CAPS as close to VDD_HV_IO_JTAG VDD_HV_IO_JTAG connector pins as possible but do NOT fit caps at board assembly. C57 DNM R20 DNM R3DNM DNP JCOMP VDD_HV_IO_JTAG R410K J41 JCOMP VDD_HV_IO_JTAG EVTI VDD_HV_IO_JTAG DRCLK JCOMP TMS TDI TDO N2514-6002RB J18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 C132 0603 DNM GND JTAG Connector C133 0603 DNM TDO PF14 (pg3,6) R17 DNM TDI TDI TDO R18 R19 0R 0R GND GND R21 R22 0R 0R (pg3,5) PORST (VSS) (VSS) (pg3) TCK (pg3) EVTI TCK EVTI_0/EVTO_0 (VSS) R28 STRIP3PMD-2MM 1 (VSS) GNDTMS (pg3)SIPI_TXP (pg3) SIPI_TXN (pg3)SIPI_RXN (pg3)SIPI_RXP CN1 2 GND 3 4 DNM (pg3) EVTO EVTO SAMTEC TFM-105-02-L-D-WT C134 27pF 0603 PORST_ESR0 TMS STRIP3PMD-2MM PORST_ESR0 TMS 1 5 6 TCK (pg3) 1 7 8 2 9 10 2 3 3 R23 DNM J42 TDI, TDO, TCK, TMS & JCOMP are not connected to daughter card. GND PORST, ESR0, EVTI and EVTO are connected to daughtercard JCOMP R24 DNM DNP SMPS_REGULATOR_OUT PG15 PIN 141 (smps_nmos1) (pg3) JCOMP_RxDATA_N (pg3) EVTO (pg3) TMS_TxDATA_P TDO_RxDATA_P (pg3) TDI_TxDATA_N (pg3) PORST (pg3,5) (pg3) EVTI (pg3,5) ESR0 ESR0 (pg3,5) GND PORST SIPI interface ERF8-005-05.0-L-DV-L-TR J20 SIPI_TXP 1 2 SIPI_TXN 3 4 5 6 PF14 SIPI_RXN 7 8 SIPI_RXP 9 10 11 12 GND Previson SPC58EE84E7/SPC58NE84E7 DC-DC Regulator VDD_HV_IO_MAIN 1J36 23456 STRIP (pg3,6) PH[0..15] (pg3,6) PG[0..15] 12PIN 140 3(smps_vlx) PH0 4PIN (smps_pmos0) 138 5PH1 6 GND Figure 7. Clock and reset circuitry External Oscillator External Clock Input J21 EVB-EXTAL 3 EVB-EXTAL R52 EXTAL (MCU Crystal Input) EXTAL(pg3) 1 J22 3.3V_SRSTRIP2PMD-2MM-O STRIP3PMD-2MM XTAL(pg3) GND J24 STRIP3PMD-2MM Connect XTAL jumper to GND when driving EXTAL from Oscilaltor Mode) Module or External Source (PLL Bypass PORST(pg3,5) RST-SW (pg6) C58 100nF 2 1 DNM R6DNM Loop Controlled Pierce Oscillator Circuit REMOVE Oscillator Module XTAL jumper or External when Source driving EXTAL (PLL Enabled) from R8 100R Reset Circuit R9 10K GND GND GND Note - External 3.3V regulator enabled when MUST using be oscillator module SMA Connector style U2 Y1J23 40MHz 1 8MHz EN +Vs 4 2 GND OUT 3 R7 0R STRIP3PMD-2MM SW1 Pushbutton NO B6110-03 Note - Internal 2 XTAL Pull-Up on Pin 1 GND (MCU Crystal Output) 1 VSS_OSC OSC-MOD 1 2 3 GND EVB-EXTAL EVB-EXTAL EXTAL-SMA P1SMA-FEM-1801 2VDD_HV_IO_MAIN VDD_HV_IO_MAIN R13 U3B 4K7 5 Vcc 6 1 J25 2 ESR0 ESR0(pg3,5) GNDSTRIP2PMD-2MM VDD_HV_IO_MAIN USR RESET LED VDD_HV_IO_MAIN 74LVC125AMTR R10 560R GND R11 4K7 VDD_HV_IO_MAIN GND Vcc J26 GNDSTRIP2PMD-2MM VDD_HV_IO_MAIN MCU RESET LED R12 560R D1 Yellow D4Red J27 RST-MCU STRIP2PMD-2MM GND GND RST-SW R14 4K7 GND U4174V1G08STR 2 VCC 4 U3A Vcc 2 3 1 2 GND74LVC125AMTR Reset-In Disable U3C 9 8 1 2 PORST 74LVC125AMTR Figure 8. Daughter card to motherboard connector PortA PortB PortC PortD PortE PortF PortG PortH PortI PortJ PA[0..15] (pg4) PB[0..15] PB[0..15] (pg4) PC[0..15] PC[0..15] (pg4) PD[0..15] PD[0..15] (pg4) PE[0..15] PE[0..15] (pg4,6) PF[0..15] PF[0..15] (pg4) PG[0..15] PG[0..15] (pg4) PH[0..15] PH[0..15] (pg4) PI[0..15] PI[0..15] (pg4) PJ[0..4] PJ[0..4] PA0 PB0 PC0 PD0 PE0 PF0 PG0 PH0 PI0 PJ0 PA1 PB1 PC1 PD1 PE1 PF1 PG1 PH1 PI1 PJ1 PA2 PB2 PC2 PD2 PE2 PF2 PG2 PH2 PI2 PJ2 PA3 PB3 PC3 PD3 PE3 PF3 PG3 PH3 PI3 PJ3 PA4 PB4 PC4 PD4 PE4 PF4 PG4 PH4 PI4 PJ4 PB5 PC5 PD5 PE5 PF5 PG5 PH5 PI5 PB6 PC6 PE6 PF6 PG6 PH6 PI6 PB7 PC7 PE7 PF7 PG7 PH7 PI7 PB8 PC8 PD8 PE8 PF8 PG8 PH8 PI8 PB9 PC9 PD9 PE9 PF9 PG9 PH9 PI9 PA10 PB10 PC10 PD10 PE10 PF10 PG10 PH10 PI10 PA11 PB11 PC11 PD11 PE11 PF11 PG11 PH11 PI11 PA12 PB12 PC12 PD12 PE12 PF12 PG12 PH12 PI12 PA13 PB13 PC13 PD13 PE13 PG13 PH13 PI13 PB14 PC14 PD14 PE14 PF14 PG14 PH14 PI14 PA15 PB15 PC15 PD15 PE15 PF15 PG15 PH15 PI15 J16A J16B VDD_HV_IO_FLEX PH11 SAMTEC QSH-120-01-L-D-A (pg2) PL8 SAMTEC QSH-120-01-L-D-A J17B1 3 1 5.0V_LR 121 123 125 127 129 121 123 125 127 122 122 5.0V_LR 124 126 128 124 126 128 130 131 133 135 137 139 141 129 131 133 135 137 139 130 132 134 136 138 140 132 134 136 138 140 142 143 145 147 149 151 153 141 142 143 144 145 146 147 148 149 150 151 152 144 146 148 150 152 154 155 157 159 161 163 165 153 155 157 159 161 163 154 156 158 160 162 164 156 158 160 162 164 166 167 169 171 173 175 177 165 167 169 171 173 175 166 168 170 172 174 176 168 170 172 174 176 178 179 181 183 185 187 189 177 179 181 183 185 187 178 180 182 184 186 188 180 182 184 186 188 190 191 193 195 197 199 189 190 191 192 193 194 195 196 197 198 3.3V_SR 201 199 200 3.3V_SR 203 205 207 209 211 213 192 194 196 198 200 202 201 202 203 204 205 206 207 208 209 210 211 212 204 206 208 210 212 214 215 217 219 221 223 225 213 215 217 219 221 223 214 216 218 220 222 224 216 218 220 222 224 226 226 228 230 232 234 236 SAMTEC QSH-120-01-L-D-A 228 230 232 234 236 238 238 240 240 VDD_HV_IO_MAIN 227 229 231 233 235 237 225 227 229 231 233 235 239 237 239 SH10 SH11 SH10 SH11 SH12 SH12 SH13 SH14 SH15 SH16 SH13 SH14 SH15 SH16 J17ASH16 5 7 SAMTEC QSH-120-01-L-D-A SH16 SH15 SH14 SH13 SH15 SH14 SH12 SH11 SH10 SH13 SH12 SH11 SH10 SH1 240 238 236 234 232 230 228 240 238 236 234 232 230 226 224 222 220 218 216 228 226 224 222 220 218 PB15 214 212 210 208 206 204 216 214 212 210 208 206 202 200 198 196 194 192 204 202 200 198 196 194 190 188 186 184 182 180 192 190 188 186 184 182 178 176 174 172 170 168 180 178 176 174 172 170 166 164 162 160 158 156 168 166 164 162 160 158 154 152 150 148 146 144 156 154 152 150 148 146 142 140 138 136 134 132 144 142 140 138 136 134 130 128 126 124 122 132 130 128 126 124 122 SH8 SH7 SH6 SH8 3 5 SH7 SH6 SH5 9 11 13 15 17 SH9 SH9 19 7 9 11 13 15 17 SH5 SH4 SH3 SH2 SH4 SH3 SH2 SH1 239 21 23 25 27 29 31 19 21 23 25 27 29 239 237 235 233 231 229 237 235 233 231 229 227 33 35 37 39 41 43 31 33 35 37 39 41 227 225 223 221 219 217 225 223 221 219 217 215 45 47 49 51 53 55 43 215 45 213 47 211 49 209 51 207 53 205 213 211 209 207 205 203 57 59 61 63 65 67 55 57 59 61 63 65 203 201 199 197 195 193 201 199 197 195 193 191 69 71 73 75 77 79 67 69 71 73 75 77 191 189 187 185 183 181 189 187 185 183 181 179 81 83 85 87 89 91 79 81 83 85 87 89 179 177 175 173 171 169 177 175 173 171 169 167 93 95 97 99 101 103 2 4 6 91 167 93 165 95 163 97 161 99 159 101 157 165 163 161 159 157 155 105 107 109 111 113 115 103 105 107 109 111 113 155 153 151 149 147 145 153 151 149 147 145 143 117 119 115 117 119 2 4 6 8 8 10 12 14 16 18 10 12 14 16 18 20 20 22 24 26 28 30 22 24 26 28 30 32 32 34 36 38 40 42 34 36 38 40 42 44 44 46 48 50 52 54 46 48 50 52 54 56 56 58 60 62 64 66 143 141 139 137 135 133 58 60 62 64 66 68 68 70 72 74 76 78 141 139 137 135 133 131 131 129 127 125 123 121 70 72 74 76 78 80 80 82 84 86 88 90 129 127 125 123 121 82 84 86 88 90 92 92 94 96 98 100 102 94 96 98 100 102 104 104 106 108 110 112 114 106 108 110 112 114 116 116 118 120 118 120 1.25V_SR 5.0V_LR 5.0V_LR 1.25V_SR PA1 PA3 5.0V_LR TP22 5.0V_LR TP25 TP23 PA11 PA13 PA15 RST-SW VDD_HV_IO_FLEX 5.0V_SR VDD_HV_IO_FLEX 5.0V_SR 5.0V_SR 1 GND 120 118 116 114 112 110 108 120 118 116 114 112 110 119 119 117 115 113 111 109 117 115 113 111 109 107 5.0V_LR 5.0V_LR 106 104 102 100 98 96 108 106 104 102 100 98 107 105 103 101 99 97 105 103 101 99 97 95 94 92 90 88 86 84 96 94 92 90 88 86 95 93 91 89 87 85 93 91 89 87 85 83 1.25V_SR 1.25V_SR PB0 PB2 PB4 PB6 PB8 PB10 PB12 PB14 5.0V_SR 1.25V_SR 1.25V_SR PB1 PB3 PB5 PB7 PB9 PB11 PB13 5.0V_SR 1.25V_SR 82 80 78 76 74 72 84 82 80 78 76 74 83 81 79 77 75 73 81 79 77 75 73 71 1.25V_SR 70 68 66 64 62 60 72 70 68 66 64 62 71 69 67 65 63 61 69 67 65 63 61 59 3.3V_SR PI1 PI5 PI7 PI11 PI13 PI15 VDD_HV_IO_MAIN 58 56 54 52 50 48 60 58 56 54 52 50 59 57 55 53 51 49 57 55 53 51 49 47 46 44 42 40 38 36 48 46 44 42 40 38 47 45 43 41 39 37 45 43 41 39 37 35 1.25V_SR VDD_HV_IO_MAIN 34 32 30 28 26 24 36 34 32 30 28 26 VDD_HV_IO_MAIN 1.25V_SR 1.25V_SR PA0 PA2 PA4 TP28 TP26 PA10 PA12 (pg7) RST-SW TP24 5.0V_SR 5.0V_SR PC0 PC2 PC4 PC6 PC8 PC10 PC12 PC14 3.3V_SR 3.3V_SR 1.25V_SR 5.0V_SR PI2 PI4 PI6 35 33 31 29 27 25 22 20 18 16 14 12 24 22 20 18 16 14 33 31 29 27 25 23 3.3V_SR 3.3V_SR 23 21 19 17 15 13 21 19 17 15 13 11 VDD_HV_IO_MAIN PJ0 PJ2 PJ1 PJ3 10 8 6 4 2 12 10 8 6 4 2 (pg4) PA[0..15] PC1 PC3 GND PC5 PC7 PC9 PC11 PC13 PC15 1.25V_SR 1.25V_SR 3.3V_SR 1.25V_SR 1.25V_SR 5.0V_SR 5.0V_SR 3.3V_SR PD0 PD1 PE0 PE1 PD2 PD3 PE2 PE3 1.25V_SR 1.25V_SR PD4 PD5 PE4 PE5 PE6 PE7 PD8 PD9 PE8 PE9 PD10 PD11 PE10 PE11 PD12 PD13 PE12 PE13 PD14 PD15 PE14 PE15 3.3V_SR 1.25V_SR 1.25V_SR 5.0V_SR 5.0V_SR 11 9 7 5 3 9 7 5 3 1 VDD_HV_IO_FLEX VDD_HV_IO_FLEX TP29 TP27 5.0V_SR 5.0V_SR 5.0V_SR 5.0V_SR 3.3V_SR 3.3V_SR 1.25V_SR PF0 PF1 PG0 PG1 PF2 PF3 PG2 PG3 5.0V_SR 5.0V_SR PF4 PF5 PG4 PG5 PF6 PF7 PG6 PG7 PF8 PF9 PG8 PG9 PF10 PF11 PG10 PG11 PF12 PG12 PG13 PF14 PF15 PG14 PG15 5.0V_SR 5.0V_SR 1.25V_SR PH3 PH5 3.3V_SR 3.3V_SR PH7 PJ4 TP30 3.3V_SR 1.25V_SR 3.3V_SR 1.25V_SR PH0 PH1 PI0 PH2 PI3 3.3V_SR 3.3V_SR PH4 PH6 PH8 PH9 PI8 PI9 PH10 PI10 PH12 PH13 PI12 PH14 PH15 PI14 3.3V_SR VDD_HV_IO_MAIN 3.3V_SR VDD_HV_IO_MAIN VDD_HV_IO_MAIN SH1 SH2 SH9 SH3 SH4 SH1 SH2 SH3 SH9 SH5 SH6 SH7 SH8 SH4 SH5 SH6 SH7 SH8 1.25V_SR 3.3V_SR 5.0V_SR 5.0V_LR VDD_HV_IO_MAIN 1.25V_SR 3.3V_SR 5.0V_SR 5.0V_LR VDD_HV_IO_MAIN GND UM2723 Revision history Table 15. Document revision history Date Version Changes 16-Jun-2020 1 Initial release. UM2723 - Rev 1 page 24/28 UM2723 Contents Contents 1 Overview . . .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .2 1.1 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 License agreement .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. ..3 3 Handling precautions. .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. ..4 4 Hardware description. .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .. ..5 4.1 Hardware features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4.2 Hardware dimension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Power and system configuration.. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . ..7 5.1 Power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.2 JTAG/LFAST LVDS/ SIPI interface configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.3 System clock configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.4 Reset circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.5 Other jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.6 Configuration for SPC58EE84E7/SPC58NE84E7 (default configuration) . . . . . . . . . . . . . . . . 9 5.7 Configuration for SPC58EE84E7/SPC58NE84E7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 5.8 Configuration for SPC58XN8XE7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 5.9 Configuration for SPC58XN8XE7 ED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.10 Configuration for SP58xG8xE7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6 Hardware description. .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .12 6.1 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 6.2 Test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 6.3 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 7 BOM. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. .17 8 Schematic. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .20 Revision history .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .. . .. . .. . .. .. . .. . .. .. . .. . .. .24 UM2723 - Rev 1 page 25/28 UM2723 List of tables List of tables Table 1. Power configuration jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 2. LFAST configuration jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 3. Clock configuration jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 4. Reset configuration jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 5. Other jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 6. SPC58EE84E7/SPC58NE84E7 configuration jumpers (default configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 7. SPC58EE84E7/SPC58NE84E7 configuration jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 8. SPC58XN8XE7 configuration jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 9. SPC58XN8XE7 ED configuration jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 10. SP58xG8xE7 configuration jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 11. Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 12. Test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 13. Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 14. BOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 15. Document revision history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 UM2723 - Rev 1 page 26/28 UM2723 List of figures List of figures Figure 1. SPC58XXADPT176S Rev. B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. SPC58XXADPT176S Rev. B top component view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 3. Overview of SPC58XXADPT176S Rev. B mini module - top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 4. Overview of SPC58XXADPT176S Rev. B mini module - bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 5. Microcontroller pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 6. JTAG, JTAG/LFAST LVDS interface, SIPI I/F and SMPS interface CONN. . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 7. Clock and reset circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 8. Daughter card to motherboard connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 UM2723 - Rev 1 page 27/28 UM2723 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2020 STMicroelectronics – All rights reserved UM2723 - Rev 1 page 28/28


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply