SPECO TECHNOLOGIES O4P30X (02) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD SPECO TECHNOLOGIES O4P30X (02) PDF MANUAL


PDF Content Summary: Quick Start Guide 4MP 30X PTZ IP Camera O4P30X Version 1.0.1 Table of Contents 1 DEVICE CHECK AND INSTALLATION ............................................................................ 1 1.1 Installation Requirements ......................................................................................... 1 1.2 Check Accessories ..................................................................................................... 1 1.3 Open the Device ....................................................................................................... 1 1.4 SD Card Installation ................................................................................................... 2 1.5 Reset ........................................................................................................................ 2 1.6 Speed Dome Installation ........................................................................................... 3 1.6.1 Quick Installation port ........................................................................................... 3 1.6.2 Cable Connection ................................................................................................... 3 1.6.3 Install the speed dome .......................................................................................... 4 2 BRACKET DIMENSIONS .............................................................................................. 6 2.1 Wall Mount Bracket .................................................................................................. 6 3 WALL MOUNT INSTALLATION .................................................................................... 7 3.1 Component Installation ............................................................................................. 7 3.2 Installation................................................................................................................ 7 3.2.1 Installation Requirements ...................................................................................... 7 3.2.2 Installation Steps ................................................................................................... 7 4 IP SCANNER .............................................................................................................. 9 4.1 Overview .................................................................................................................. 9 4.2 Operation ................................................................................................................. 9 5 WEB OPERATION .................................................................................................... 10 5.1 Login and Main Interface ......................................................................................... 10 6 APPENDIX IIII SURGE PROTECTION ............................................................................. 11 7 APPENDIX III 24V AC CABLE DIAMETER AND TRANSMISSION DISTANCE RELATIONSHIP ................................................................................................................ 12 i 8 APPENDIX IV WIRE GAUGE REFERENCE .................................................................... 13 ii Welcome Thank you for purchasing this Network camera! This manual is designed to be a reference tool for your system. Please read this manual carefully before operating the unit and retain it for future reference. Should you require any technical assistance, please contact Speco Technologies Technical Support. iii Important Safeguards and Warnings 1.Electrical safety All installation and operation here should conform to local electrical safety codes. Use a certified/listed 12VDC Class 2 power supply only. Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage! The product must be grounded to reduce the risk of electric shock. Improper handling and/or installation could run the risk of fire or electrical shock. 2.Environment Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation. This product should be installed in a cool, dry place away from direct sunlight and heat sources. Do not install the product in extreme temperature conditions. Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure. Do not block any ventilation openings. Do not allow water and liquid intrusion into the camera. 3. Operation and Daily Maintenance Please shut down the device and then unplug the power cable before you begin any maintenance work. Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean the device. Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection. The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera. Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use, please refer to the following methods if dirt is found: Stained with dirt Use oil-free soft brush or hair dryer to remove it gently. Stained with grease or fingerprint Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens iv center outward. Change the cloth and wipe several times if it is not clean enough. Warning This camera should be installed by qualified personnel only. All the examination and repair work should be done by qualified personnel. Any unauthorized changes or modifications could void the warranty. Statement This guide is for reference only. Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these without notice and without incurring any obligation. Speco Technologies is not liable for any loss caused by improper operation. Note: Before installation, check the package and make sure that all components are included. Keep the package material in case the camera needs to be sent back for service or repair. Contact your rep or Speco customer service department immediately if something is broken or missing in the package. v 1 Device Check and Installation 1.1 Installation Requirements Basic Requirement ● All installation and operation here should conform to your local electrical safety codes. ● Before installation, please open the package and make sure all components are included. Please make sure the speed dome installation environment can meet your requirement. If there is special requirement, please contact your local dealer for more information. ● We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. 1.2 Check Accessories Before installation, check the package and make sure that all components are included. Contact your rep or Speco customer service department immediately if something is broken or missing in the package. Accessory Name Amount Network Camera Unit 1 Quick Start Guide 1 Wall Mounting Bracket 1 Installation Accessories Bag 1 CD 1 1.3 Open the Device Please open the box and then take out the speed dome. Remove the bracket component, take out the EPE foam around the module, Figure 1-1. 1 Figure 1-1 1.4 SD Card Installation Remove the bracket component; open the cover and locate the micro-SD card slot on the module ISP board (see Figure 1-2). Figure 1-2 1.5 Reset Locate the reset button on the PTZ mainboard after you remove the bracket component. See Figure 1-3. Reset button is used to reset the camera back to factory default. 2 Figure 1-3 1.6 Speed Dome Installation 1.6.1 Quick Installation port Now you can install the quick installation port. Please twist Teflon tape around the screw thread of the quick installation port and turn it into the screw thread of the wall mount bracket. Use M4 stainless screws to secure firmly. See Figure 1-4. Figure 1-4 1.6.2 Cable Connection ● Connect the safety hook of the intelligent speed dome cover to the hook of the quick installation port. 3 ● Connect the necessary cables. 1.6.3 Install the speed dome Step 1 Pull the cable to the wall mount bracket slowly. Step 2 Line up the straight edge of the flange of the speed dome to the straight edge of the quick installation port, and then push the speed dome to the bottom of the port slowly. Step 3 Use your hands to turn the quick installation port M6*14 stainless screw (with spring washer) to the Ф6.5 hole of the straight edge of the speed dome. Turn other two M6*14 stainless screws to groove of speed dome flange. Use the inner hex tool to fix these three stainless screws. Now you have completed the installation. See Figure 1-5. Figure 1-5 Step 4 Please make sure: ● The three stainless screws of the quick installation port are firmly secured. ● The speed dome is fixed. ● The speed dome is straight. ● The safety hook connection is firm. After your installation, the interface is shown as in Figure 1-6. 4 Figure 1-6 5 2 Bracket Dimensions 2.1 Wall Mount Bracket The wall mount bracket dimensions are shown as below. See Figure 2-1. Figure 2-1 6 3 Wall Mount Installation 3.1 Component Installation Wall mount bracket is shown as below. See Figure 3-1. Figure 3-1 3.2 Installation 3.2.1 Installation Requirements The wall mount speed dome can be installed on a hard surface wall. Before the installation, please make sure: ● The wall is thick enough to install the expansion bolt. ● The wall can at least sustain the 8x weight of the speed dome, bracket and the accessories. 3.2.2 Installation Steps Step 1 See Figure 3-2. Please draw four holes position in the wall according to the hole of the bottom of the wall mount bracket. Use four hex bolts and flat washer to fix the bracket in the expansion bolts. 7 Figure 3-2 Step 2 Install the speed dome on the bracket. See Figure 3-3. Please refer to section 1.6 Speed Dome Installation for more details. Figure 3-3 8 4 IP Scanner 4.1 Overview IP Scanner can search for the device on the lo Please note that only devices that are on the 4.2 Operation Open up IP Scanner. Figure 4-1 In the device list, you can view the IP address device. Select the applicable device and doub h for the device on the local network. y devices that are on the same subnet can be discovered. u can view the IP address, model number, and MAC address of each plicable device and double click to open up the web viewer. Figure 4-1 IP Scanner 9 AC address of each web viewer. 5 Web Operation This device supports viewing and manageme 5.1 Login and Main Interface Open the browser and input network camera device in IP Scanner. See Figure 5 The login interface is shown as below. See Please input your user name and password Default user name is admin and password is Note: For security purposes, please change viewing and management via a web browser on a PC. d Main Interface nd input network camera address in the address bar or double click the Figure 5-1. Figure 5-1 IP address s shown as below. See Figure 5-2. ser name and password. and password is 1234. urposes, please change the password after initial login. Figure 5-2 Web login 10 s bar or double click the initial login. Input your IP address here 6 APPENDIX I Surge Protection This device uses TVS lighting protection technology. It can effectively prevent damages from various pulse signals below 2000W, such as sudden lighting and surge. While maintaining your local electrical safety code, you still need to take necessary precaution measures when installing the speed dome in an outdoor environment. ● The distance between the signal transmission cable and high-voltage device (or high- voltage cable) shall be at least 50 meters (164 ft). ● Outdoor cable layout shall go under the penthouse if possible. ● For vast land, please use sealing steel tube under the land to implement cable layout and connect one point to the earth. Open floor cable layout should not be used. ● In areas prone to strong thunderstorms or near high sensitive voltage (such as near high-voltage transformer substation), you need to install additional high-power lightning protection device or lightning rod. ● The lightning protection and earth of the outdoor device and cable shall be considered under the lightning protection of the whole building and conform to your local national or industry standard. ● System shall adopt equal-potential wiring. The earth device shall meet anti-jamming and at the same time conform to your local electrical safety code. The earth device shall not short circuit to N (neutral) line of high voltage power grid or mixed with other wires. When connecting the system to earth alone, the earth resistance shall not be more than 4Ω and earth cable cross-sectional area shall be below 25 mm^2. See Figure 6-1. Figure 6-1 11 7 APPENDIX III 24V AC Cable Diameter and Transmission Distance Relationship It is the recommended transmission distance when the cable diameter is fixed and the 24V AC power consumption is below 10%. For the AC device, the max permission voltage power consumption is 10%. For example, when a device of rated power 20W installed from the transformer 141 inches (42m), then the min cable diameter is 0.8000mm. mm Feet(m) w 0.8000 1.000 1.250 2.000 5 488.52 (148.90) 763.31 (232.66) 1192.67 (363.53) 3053.25 (930.63) 10 244.26 (74.45) 381.66 (116.33) 596.34 (181.76) 1526.62 (465.31) 15 162.84 (49.63) 254.44 (77.55) 397.56 (121.18) 1017.75 (310.21) 20 122.13 (37.23) 190.83 (58.16) 298.17 (90.88) 763.31 (232.66) 25 97.70(29.78) 152.66 (46.53) 238.53 (72.71) 610.65 (186.13) 30 81.42(24.82) 127.22 (38.78) 198.78 (60.59) 508.87 (155.10) 35 69.79(21.27) 109.04 (33.24) 170.38 (51.93) 436.18 (132.95) 40 61.06(18.61) 95.41(29.08) 149.08 (45.44) 381.66 (116.33) 45 54.28(16.54) 84.81(25.85) 132.52 (40.39) 339.25 (103.40) 50 48.85(14.89) 76.33(23.27) 119.27 (36.35) 305.32(93.06) 55 44.41(13.54) 69.39(21.15) 108.42 (33.05) 277.57(84.60) 60 40.71(12.41) 63.61(19.39) 99.39(30.29) 254.44(77.55) 65 37.58(11.45) 58.72(17.90) 91.74(27.96) 234.87(71.59) 70 34.89(10.64) 54.52(16.62) 85.19(25.97) 218.09(66.47) 75 32.57(9.93) 50.89(15.51) 79.51(24.24) 203.55(62.04) 80 30.53(9.31) 47.71(14.54) 74.54(22.72) 190.83(58.16) 85 28.74(8.76) 44.90(13.69) 70.16(21.38) 179.60(54.74) 90 27.14(8.27) 42.41(12.93) 66.26(20.20) 169.62(51.70) 95 25.71(7.84) 40.17(12.25) 62.77(19.13) 160.70(48.98) 100 24.43(7.45) 38.17(11.63) 59.63(18.18) 152.66(46.53) 12 8 APPENDIX IV Wire Gauge Reference

Metric bare wire diameter (mm) AWG SWG Bare wire cross section (mm2)

0.050 43 47 0.00196 0.060 42 46 0.00283 0.070 41 45 0.00385 0.080 40 44 0.00503 0.090 39 43 0.00636 0.100 38 42 0.00785 0.110 37 41 0.00950 0.130 36 39 0.01327 0.140 35 0.01539 0.160 34 37 0.02011 0.180 33 0.02545 0.200 32 35 0.03142 0.230 31 0.04115 0.250 30 33 0.04909 0.290 29 31 0.06605 0.330 28 30 0.08553 0.350 27 29 0.09621 0.400 26 28 0.1257 0.450 25 0.1602 0.560 24 24 0.2463 0.600 23 23 0.2827 0.710 22 22 0.3958 0.750 21 0.4417 0.800 20 21 0.5027 0.900 19 20 0.6362 1.000 18 19 0.7854 1.250 16 18 1.2266 1.500 15 1.7663 2.000 12 14 3.1420 2.500 4.9080 3.000 7.0683 13


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply