SONY ZV-1 (04) PDF Document

The number in parentheses indicates the number of pieces.

Camera (1)

Rechargeable battery pack NP-BX1 (1)

Micro USB cable (1)

Wind screen (1) (attached to the wind screen adaptor)

Wind screen adaptor (1)

Shoe cap (1) (attached to the camera)

Startup Guide (1)

Reference Guide (1)

1. Open the battery/memory card cover.

2. Insert the battery pack. Make sure that the battery pack is facing in the correct direction, and insert it while pressing the battery lock lever.

3. Insert the memory card. Ensure the notched corner faces correctly as illustrated.

4. Close the cover.

This camera is compatible with SD memory cards or Memory Stick media.

When you use a memory card with this camera for the first time, format the card using the camera in order to stabilize the performance of the memory card.

Note: Formatting erases all data, including protected images and registered settings (M1 to M4). Once erased, this data cannot be restored. Save valuable data to a computer, etc. before formatting.

1. Turn the power off. If the camera is turned on, the battery pack will not be charged.

2. With the battery pack inserted, connect the camera to the computer using the supplied micro USB cable.

3. The charge lamp will light up when charging starts. When the charge lamp turns off, charging is completed.

1. Press the ON/OFF (Power) button to turn on the camera.

2. Select the desired language using the control wheel, and then press the center of the control wheel.

3. Make sure that [Enter] is selected on the screen and then press the center button.

4. Select the desired geographic location and then press the center button.

5. Set [Daylight Savings], [Date/Time], and [Date Format], and then select [Enter] and press the center button.

If you want to reconfigure the date/time or the area setting at a later point, press the MENU button and select (Setup) then [Date/Time Setup] or [Area Setting].

1. Select the desired shooting mode by pressing the MODE (Mode) button and using the control wheel, and then press the center.

2. Press the shutter button halfway down to focus.

3. Press the shutter button all the way down.

1. Press the MOVIE (Movie) button to start recording. Movie recording can be started from any shooting mode in the default setting.

2. Press the MOVIE button again to stop recording.

Use the MODE (Mode) button to change shooting modes. Press the MODE button and use the control wheel to select the desired mode, and then press the center.

Use the wind screen to reduce wind noise picked up by the internal microphone when recording a movie. Remove the shoe cap from the camera, and then attach the wind screen to the Multi Interface Shoe.

1. Press the Playback button to switch to the playback mode.

2. Select an image with the control wheel. You can move to the previous image/next image by pressing the left/right side of the control wheel.

To start playing back a movie, press the center button on the control wheel.

You can transfer images to a smartphone by connecting the camera and a smartphone via Wi-Fi.

1. Install Imaging Edge Mobile on your smartphone. If already installed, ensure it is updated to the latest version.

2. Connect the camera and your smartphone using the QR Code.

On the camera: MENU -> Network -> [Send to Smartphone Func.] -> [Send to Smartphone] -> [Select on This Device] -> select images to transfer. If you want to select images on the smartphone, select [Select on Smartphone].

On the smartphone: Launch Imaging Edge Mobile and select [Scan QR Code of the Camera]. Scan the QR Code displayed on the camera using your smartphone.

3. The selected images will be transferred.

Note: If you are using Android, you can transfer images after the first time simply by launching Imaging Edge Mobile with the steps above. If image transfer does not start, select the camera to connect on the screen of your smartphone.

PlayMemories Home: This software allows you to import still images and movies to your computer and view or use them. You need to install PlayMemories Home to import XAVC S movies or AVCHD movies to your computer.

Imaging Edge: This is a software suite that includes functions such as remote shooting from a computer, and adjusting or developing RAW images recorded with the camera.

The camera is neither dust-proof, nor splash-proof, nor water-proof.

Do not leave the lens exposed to a strong light source such as sunlight. Doing so may cause smoke, fire, or a malfunction inside the camera body or the lens.

When you shoot with backlighting, keep the sun sufficiently far away from the angle of view. Otherwise, the sunlight may enter the focus inside the camera and cause smoke or fire.

Do not directly expose the lens to beams such as laser beams. That may damage the image sensor and cause the camera to malfunction.

Do not leave the camera, the supplied accessories, or memory cards within the reach of infants.

This camera (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this camera close to persons who use such medical devices. Consult your doctor before using this camera if you use any such medical device.

This camera is equipped with a magnetic sensor. If the camera is placed too close to a magnet or a device with an internal magnet, the lens may activate. Take care not to place the camera near any magnetic devices.

The monitor is manufactured using extremely high-precision technology, and over 99.99% of the pixels are operational for effective use. However, there may be some small black dots and/or bright dots (white, red, blue or green in color) that constantly appear on the monitor. These are imperfections due to the manufacturing process and do not affect the recorded images in any way.

If the monitor is damaged, stop using the camera immediately. The damaged parts may harm your hands, face, etc.

During continuous shooting, the monitor may flash between the shooting screen and a black screen. If you keep watching the screen in this situation, you may experience uncomfortable symptoms such as feeling of unwellness. If you experience uncomfortable symptoms, stop using the camera, and consult your doctor as necessary.

Depending on the camera and battery temperature, the camera may become unable to record movies or the power may turn off automatically to protect the camera. A message will be displayed on the screen before the power turns off or you can no longer record movies. In this case, leave the power off and wait until the camera and battery temperature goes down. If you turn on the power without letting the camera and battery cool sufficiently, the power may turn off again, or you may still be unable to record movies.

The camera body and battery may become warm with use; this is normal.

If the same part of your skin touches the camera for a long period of time while using the camera, even if the camera does not feel hot to you, it may cause symptoms of a low-temperature burn such as redness or blistering. Pay special attention in the following situations and use a tripod, etc.:

When using the camera in a high temperature environment.

When someone with poor circulation or impaired skin sensation uses the camera.

When using the camera with [Auto Power OFF Temp.] set to [High].

Use a tripod with a screw less than 5.5 mm (7/32 inches) long. Otherwise, you cannot firmly secure the camera, and damage to the camera may occur.

If you upload and share an image tagged with a location, you may accidentally reveal the information to a third party. To prevent third parties from obtaining your location information, set [Location Info. Link Set.] to [Off] before shooting images.

Before discarding or transferring this product to others, be sure to perform the following operation to protect private information: Select [Setting Reset] -> [Initialize].

Regarding memory cards: Executing [Format] or [Delete] on the camera or a computer may not completely delete the data on the memory card. Before transferring a memory card to others, we recommend that you delete the data completely using data deletion software. When discarding a memory card, we recommend that you physically destroy it.

When you board an airplane, etc., you can turn off all wireless network functions temporarily using [Airplane Mode].

Camera Type: Digital Camera

Image Sensor: 13.2 mm x 8.8 mm (1.0 type), CMOS image sensor

Effective pixel number of camera: Approx. 20 100 000 pixels

Total pixel number of camera: Approx. 21 000 000 pixels

Monitor: 7.5 cm (3.0 type) TFT drive, touch panel

General Rated input: 3.6 V, 2.1 W

Operating temperature: 0 to 40 degrees Celsius (32 to 104 degrees Fahrenheit)

Storage temperature: -20 to 55 degrees Celsius (-4 to 131 degrees Fahrenheit)

Dimensions (W/H/D) (Approx.): 105.5 x 60.0 x 43.5 mm (4 1/4 x 2 3/8 x 1 3/4 in.)

Mass (Approx.): 294 g (10.4 oz) (including battery pack, SD Card)

Wireless LAN Supported format: IEEE 802.11 b/g/n

Wireless LAN Frequency band: 2.4 GHz

Wireless LAN Security: WEP/WPA-PSK/WPA2-PSK

Wireless LAN Connection method: Wi-Fi Protected Setup (WPS)/Manual

Wireless LAN Access method: Infrastructure mode

Rechargeable battery pack NP-BX1 Rated voltage: 3.6 V