SONY SNC-EB632R (01) PDF MANUAL

SONY SNC-EB632R (01) PDF SUMMARY:

How do you reset the camera to the factory default settings?

To reset the camera to the factory default settings, hold down the reset switch with a point and supply the power to the camera.

How do you switch the video output?

You can switch the video output using the VIDEO (NTSC/PAL) switch (Initial setting: NTSC). After setting the switch, reboot the camera unit.

How do you adjust the lens’ zoom and focus?

Use the ZOOM/FOCUS switch to adjust lens’ zoom and focus. Slide the switch lever to select the desired function.

• [W] WIDE: Zoom out
• [T] TELE: Zoom in
• [N] NEAR: Focus on a nearby subject
• [F] FAR: Focus on a distant subject

Hold down the center of the ZOOM/FOCUS switch for a moment to focus automatically.

How do you install the camera?

1. Pass the LAN cable and the ground wire through the hole for connecting cables made at the installing surface.
2. Fix the wire rope to the wall or ceiling.
3. Install the camera on the wall or ceiling. The remaining cable can be incorporated in the space between the base stand and the mounting surface.
4. Insert the four screws in the screw holes on the camera stand, and then tighten the screws to attach the camera. When installing the camera on the wall, be sure the TOP mark on the camera stand is at the top. Refer to “Mounting screws” for screw to be used.

What are the notes on waterproofing of the cable connection area?

Despite the fact that this unit is rated IP66, the cables and/or the connectors join to the outside are not waterproof. To prevent water ingress from the cables and/or the connectors, waterproof them with the supplied waterproof tape as follows. Otherwise, there may be a risk of water entering through the cables and/or the connectors and shorting the unit or the connectors.

1. Connect the LAN cable and the ground wire.
2. To obtain optimal waterproofing, tear off the liner before wrapping, then stretch the tape to twice its original length. If it is not fully stretched, the waterproofing function of the tape can not be achieved.
3. Overlap the tape at least half of its width when wrapping.
4. After wrapping, squeeze the tape with your fingers at the overlapping parts so that layers are airtight and fully adhered.

How do you adjust the direction and coverage of the camera?

1. Loosen the sun shield nut manually and adjust the sun shield to the desired position horizontally. Do not loosen the sun shield nut too much, to prevent it from sliding to the back hole of the sun shield slide slot. Tighten the sun shield nut manually to secure the sun shield to the end when the nut is located at the back hole of sun shield slide slot, and take off the sun shield.
2. Loosen the four front cover screws with the supplied wrench, and take off the front cover.
3. First loosen the two base screws with the supplied wrench, then loosen the arm screw. To fine adjust, only loosen the arm screw.
4. Adjust the camera to turn the lens in the desired direction.
5. First tighten the two base screws with the supplied wrench, then tighten the arm screw (tightening torque: 2.0 N·m).
6. Adjust the zoom by the ZOOM/FOCUS switch (W/T).
7. Hold down the center of the ZOOM/FOCUS switch for a moment to focus automatically.
8. Repeat steps 3 to 7 until the coverage and the focus are determined.

How do you attach the front cover and the sun shield?

1. Check if the waterproof rubber gasket is contaminated, detached or damaged.
2. Align the four front cover screw holes with the bosses on the camera. Make sure the TOP mark on the front cover is at the top, then tighten the four screws with the supplied wrench to secure the front cover. (tightening torque: 0.4 N·m)
3. Align the back hole of the sun shield slide slot with the sun shield nut to install the sun shield, adjust the sun shield to the desired position, then tighten the sun shield nut manually.

What are the important precautions when installing the camera?

Despite the fact that this unit is rated IP66, this section includes important precautions to prevent any malfunction caused by condensation and/or water ingress. Read the precautions below thoroughly before installing the unit.

• Make sure that the cables and/or connectors of the unit that join to the ones of the installation surface are waterproofed, before you install the unit. Otherwise, there may be a risk of water entering the unit through these cables.
• Make sure to waterproof the cables and/or connectors with the supplied waterproof tape as stipulated in this manual. Otherwise, there may be a risk of water entering and shorting the unit. For details, see “Notes on waterproofing of cable connection areas”
• Install the camera stand on an even ceiling, wall, etc.

What are the important precautions to take when installing the unit in an inverted position (on a ceiling, for example)?

• Install the unit in a waterproof box or on a waterproof ceiling to prevent water entering the unit along the cables. Alternatively, seal the hole which is made for the connecting cables at the installing surface.
• Cover all around the joint part of the installing surface and the camera stand with sealant to prevent water ingress.

What are the important precautions to take when installing the unit in a vertical position (on a wall, for example)?

• Make sure the TOP mark on the camera stand is at the top.
• Cover all around the joint part of the installing surface and the camera stand (except the water drain) with sealant to prevent water ingress.

What are some notes on assembly?

• Make sure the cable and the wire rope do not get caught between the base stand and the mounting surface.
• Before attaching the front cover to the camera unit, make sure the waterproof rubber gasket is clean and fits in the groove properly.

How do you connect to the network?

Connect the LAN port of the camera to a router or hub in the network using a commercially available network cable (not supplied).

How do you connect the power source?

Power supply equipment pursuant to IEEE802.3af (PoE* system) *PoE means Power over Ethernet.

How do you connect to the power supply equipment pursuant to IEEE802.3af?

The power supply equipment pursuant to IEEE802.3af supplies the power through a commercially available network cable. For details, refer to the Instruction Manual of the equipment.

What are the recommendations for periodic inspections?

In case using this device over an extended period of time, please have it inspected periodically for safe use. It may appear flawless, but the components may have deteriorated over time, which may cause a malfunction or accident. For details, please consult the store of purchase or an authorized Sony dealer.