SONY M-100MC (01) PDF DOCUMENT

1. Insert a cassette with the side to start playing facing the lid.

2. Set TAPE SPEED to the same speed as that used for recording.

3. Press the ► (play) button.

4. Adjust the volume.

Slide the FAST PB switch in the direction of the arrow. The playback speed will be increased.

To return to the original speed, slide the FAST PB switch to the original position.

In the recording or playback mode, the tape stops at the end of the tape and the locked buttons will be released automatically (Automatic shut-off mechanism).

After fast forward or rewind, be sure to set the CUE/REVIEW switch back to the center position.

Connect another tape recorder using the RK-G64 connecting cord (not supplied).

Set the SONY M-100MC to the playback mode and the other tape recorder to the recording mode.

Operate the SONY M-100MC only on 3 V DC.

For AC operation, use the AC adaptor recommended for the unit. Do not use any other type.

For battery operation, use two R6 (size AA) batteries.

Use only the MICROCASSETTE™ (standard microcassettes) with this unit. Non-standard cassettes cannot be used because their “L” dimension is different.

Standard microcassettes have a small indention of side A and an “L” dimension of approximately 5 mm. Non-standard cassettes have a dimension of approximately 2.5 mm.

• Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.

• Should any solid object or liquid fall into the unit, remove the batteries or disconnect the AC power adaptor, and have the unit checked by qualified personnel before operating it any further.

• Keep personal credit cards using magnetic coding or spring-wound watches etc. away from the unit to prevent possible damage from the magnet used for the speaker.

• When you do not use the unit for long, remove the batteries to avoid damage caused by battery leakage and subsequent corrosion.

• If the unit has not been used for long, set it in the playback mode and warm it up for a few minutes before inserting a cassette.

Choose one of the following power sources:

Dry Batteries:

1. Make sure that nothing is connected to the DC IN 3V jack.

2. Open the battery compartment lid.

3. Insert two R6 (size AA) batteries with correct polarity and close the lid.

House current:

Connect the AC power adaptor (not supplied) to the DC IN 3V jack and to a wall outlet. Use the AC-E30HG AC power adaptor (not supplied). Do not use any other AC power adaptor.

This is a measured value by the standard of JEITA (Japan Electronics and Information Technology Industries Association) using a Sony Microcassette MC-60. The battery life may shorten depending on the operation of the unit.

Replace the batteries with new ones when the BATT indicators go off and the indicator flashes. The BATT indicators change as follows:

When batteries are new: The BATT indicator lights up.

When batteries become weak: The BATT indicator goes off and the separate indicator light comes on.

Replace batteries: The BATT indicator is off and the separate indicator flashes.

Notes:

• The unit will play back normally for a while, even after the indicator flashes. However, replace the batteries as soon as you can. If not, the playback cannot be made with normal sound, noise may be recorded and the recorded sound will not be loud enough.

• The indicator flashes to indicate battery replacement during playback, recording and pause (during pause by VOR function also).

• In the following cases you do not need to replace the batteries:

– if the BATT indicators flash with the playback sound when you turn up the volume.

– if the indicator lights momentarily when the tape starts running or at the end of the tape.

– if the indicator flashes during fast forward/CUE or rewind/REVIEW.

If the battery compartment lid is accidentally detached, attach it as illustrated in the user manual.

You can position the SONY M-100MC to record the sound more clearly using the stands. You can choose from the two types of stands depending on the recording situation:

• Pull down the built-in stand.

• Insert the rubber stand attached to the handstrap into the slot on the bottom of the unit.

1. Press the reset button of the TAPE COUNTER.

2. Press ■/스 (stop) and insert a standard microcassette with the side to start recording facing the lid.

3. Select the desired tape speed.

• 2.4cm for optimum sound (recommended for normal use): A 30-minute recording can be made using both sides of the MC-30 microcassette.

• 1.2cm for longer recording time: A 60-minute recording can be made using both sides of the MC-30 microcassette.

4. Set MIC MODE to select the sensitivity of the microphone.

5. Set VOR to ON or OFF. If you set VOR to ON, the unit automatically starts recording the sound and pauses when there is no sound.

6. Press ● (record). Recording starts. While the tape runs, the REC indicator lights and flashes depending on the strength of the sound.

Set the MIC MODE selector to the desired position on the SONY M-100MC depending on the recording situation:

Lecture: to record the sounds from where the unit is aiming (uni-directional). It is useful to record during a lecture.

Meeting: to record at meetings or in a quiet or spacious place (omni-directional).

Dictation: to record for dictation or in a noisy place (omni-directional).

The VOR system depends on the environmental conditions. If you cannot get the desired results, set VOR to OFF.

When you use VOR in a noisy place, the SONY M-100MC will stay in the recording mode. If the sound is too soft, on the contrary, the unit will not start recording.

While recording, you can record a special signal on the tape to mark a specific position.

At the desired position, push CUE MARKER to record a signal. The REC indicator goes off for a while and a signal will be recorded on the tape. If you want to record a signal longer than that, push CUE MARKER as long as you want.

During cue and review, you will hear the beep sound at the signal position. During playback, you will hear the signal with low frequency.

Notes:

• It is recommended to record cue marks when there is a break in the sound.

• During cue and review, the beep sounds differently.

• The beep may sound differently depending on the marked position on the tape because the winding speed varies from the beginning to the end of the tape.

Connect the earphone to the EAR jack. The monitor volume cannot be adjusted by the VOL control.

Break out and remove the cassette tabs. To reuse the cassette for recording, cover the tab hole with adhesive tape.

→ The cassette is being inserted in the wrong way. The cassette should be inserted in the lid with the tape side facing upward.

→ The ■/스 (stop) button has been already pressed.

→ There is no cassette in the cassette compartment.

→ The cassette tab has been removed.

→ The tape has reached the end.

→ After the automatic shut-off, the PAUSE switch is slid in the direction of the arrow.

→ The batteries have been inserted with incorrect polarity.

→ The batteries are weak. Replace both batteries with new ones.

→ The PAUSE switch is slid in the direction of the arrow.

→ The AC power adaptor or car battery cord is connected to the unit only and you are trying to use the unit on batteries.

→ The earphone is plugged in.

→ The volume is turned down completely.

→ The volume is turned down completely.

→ The batteries are weak. Replace both batteries with new ones.

→ The head is contaminated. See “Maintenance”.

→ The batteries are weak. Replace both batteries with new ones.

→ There is an improper setting of the TAPE SPEED switch. Set it to the same speed as that used for recording.

→ The FAST PB switch is slid in the direction of the arrow.

→ The batteries are weak. Replace both batteries with new ones.

→ The head is contaminated.

→ The VOR switch is set to ON. When you do not use VOR, set it to OFF.

→ Set the MIC MODE selector firmly at the correct position.

→ The VOR switch is set to ON. When you do not use VOR, set it to OFF.

→ The head is contaminated.

Press the ■/스 (stop) button and wipe the head, capstan and the pinch roller with a cotton swab, moistened with alcohol every 10 hours of use.

Use a soft cloth slightly moistened in water. Do not use alcohol, benzine or thinner.