Free English SONY IT-M804 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.


CLICK HERE TO DOWNLOAD SONY IT-M804 (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.


How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.


What items are supplied in the package with the SONY IT-M804?

The package of the SONY IT-M804 includes the following items:

Phone unit

Handset

Handset cord

AC power adaptor (AC-T71)

Three telephone line cords

Four pads

Wall bracket/stand for phone

Quick sheet

Assignment of using line sticker


What installation precautions should be observed for the SONY IT-M804?

Install the SONY IT-M804 unit:

On a level surface.

Away from heat sources, such as radiators, airducts, and direct sunlight.

Away from excessive moisture, extremely low temperatures, dust, mechanical vibration, or shock.


How many units can be connected together to use intercom features on the SONY IT-M804?

You can connect a maximum of 16 SONY IT-M804 phones to use your phone as an intercom phone, in addition to using it as a 4-line telephone.

To use the intercom features, you must connect all SONY IT-M804 phones to the LINE 1 jack correctly within a maximum distance of 300 feet.

If you set the dialing mode, area codes, and date and time on one phone after connecting other phones, these settings will be set automatically to every connected phone. Moreover, Caller ID data can be viewed on every connected phone.


How do you connect the handset to the SONY IT-M804?

Connect one end of the supplied handset cord to the handset and the other end to the HANDSET jack located on the side of the SONY IT-M804.


How do you connect the SONY IT-M804 to two telephone outlets having two lines each?

To connect the SONY IT-M804 to two outlets having two lines:

Step 1. Connect the telephone line cords to the “LINE 1/LINE 1+2” and “LINE 3/LINE 3+4” jacks on the phone and to the respective telephone wall outlets.

Step 2. Connect the supplied AC power adaptor to the DC IN 12V jack on the phone and hook the cord, then plug it into an AC outlet.


How do you connect the SONY IT-M804 to four separate telephone outlets?

If you have single-line outlets, you need two Two-Line adaptors (not supplied) to connect the SONY IT-M804:

Step 1. Connect the Two-Line adaptors to the Line 1 and Line 3 outlets.

Step 2. Connect the telephone line cords to the “LINE 1/LINE 1+2” and “LINE 3/LINE 3+4” jacks on the phone and to the Two-Line adaptors.

Step 3. Connect telephone line cords between the Two-Line adaptors and the Line 2 and Line 4 outlets.

Step 4. Connect the AC power adaptor to the DC IN 12V jack and plug it into an AC outlet.

Note: A Duplex Jack adaptor cannot be used in place of a Two-Line adaptor.


How do you connect a computer or FAX machine to the SONY IT-M804?

You can connect a computer or FAX machine to the DATA jack of the SONY IT-M804.

Select the line to be used for data communication (L2, L3, or L4) using the DATA LINE SELECT switch.

Note: Connection to ADSL devices is not possible. If a call comes in on the line selected with call waiting while data is being transmitted, data may be affected. It is recommended to dedicate the selected line strictly for data communication if used frequently.


How do you tilt the SONY IT-M804 using the wall bracket?

To tilt the SONY IT-M804 on a flat surface:

Step 1. Put the four supplied rubber pads into the hollows of the wall bracket.

Step 2. Attach the wall bracket to the bottom of the telephone.

Step 3. Connect the telephone line cords and the AC power adaptor.


How do you assign a station number on the SONY IT-M804?

To assign a station number on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “STATION #” appears on the display.

Step 3. Press the Jog Button (or PROGRAM).

Step 4. Enter the two-digit station number (01 to 16) by pressing the dialing keys.

Step 5. Press the Jog Button (or PROGRAM). You will hear a long confirmation beep.

Note: If a number already used by another phone or a number outside 01 to 16 is entered, “INVALID NUMBER” is displayed.


How do you choose the dialing mode on the SONY IT-M804?

To select tone or pulse dialing on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “DIAL MODE” appears on the display.

Step 3. Press the Jog Button.

Step 4. Turn the Jog Dial to choose “TONE” or “PULSE”, then press the Jog Button. You will hear a long confirmation beep.

Note: When other SONY IT-M804 phones are connected to LINE 1 jack, the dialing mode setting is automatically sent to all connected phones.


How do you test which dialing mode to use if you are unsure on the SONY IT-M804?

Make a trial call with the dialing mode set to “TONE”. If the call connects, leave the setting as is; otherwise, set the dialing mode to “PULSE”.


How do you enable or disable unused telephone lines on the SONY IT-M804?

If you are not using all four lines, disable the unused lines as follows:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “DISABLE LINE” appears on the display.

Step 3. Press the Jog Button.

Step 4. Turn the Jog Dial to choose the line you want to change, and press the Jog Button.

Step 5. Turn the Jog Dial to choose “ENABLE” or “DISABLE”, and press the Jog Button. A long confirmation beep will sound, and the line next to the selected line will flash.

Repeat steps 4 and 5 for other lines if necessary. Press ERASE/CLEAR to exit.

Note: Line 1 cannot be disabled.


How do you enter the home area code on the SONY IT-M804?

To enter the home area code on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “AREA CODE” appears on the display.

Step 3. Press the Jog Button.

Step 4. Press the Jog Button again when “HOME” is flashing.

Step 5. Enter the three digits of your home area code using the dialing keys. (If 10-digit dialing is required for all local calls in your area, enter “000”).

Step 6. Press the Jog Button. You will hear a long confirmation beep.


How do you change the home area code on the SONY IT-M804?

To change the home area code on the SONY IT-M804:

Step 1. Access the area code display by pressing PROGRAM, turning Jog Dial up to “AREA CODE”, and pressing the Jog Button twice so the current code is displayed.

Step 2. Enter a new home area code by pressing the dialing keys. Alternatively, turn the Jog Dial until the digit to be corrected flashes, and enter the correct digit.

Step 3. Press the Jog Button. You will hear a long confirmation beep.


How do you enter local area codes for 10-digit dialing on the SONY IT-M804?

You can register up to five local area codes on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “AREA CODE” appears on the display.

Step 3. Press the Jog Button.

Step 4. Turn the Jog Dial up to make “LOCAL” flash, then press the Jog Button.

Step 5. Select a memory slot (#1 to #5) by turning the Jog Dial, then press the Jog Button.

Step 6. Enter the three digits of the local area code by pressing the dialing keys.

Step 7. Press the Jog Button. The next number slot will flash. Repeat steps 5 to 7 to enter additional local area codes, or press ERASE/CLEAR to exit.


How do you erase a local area code from the SONY IT-M804?

To erase a local area code on the SONY IT-M804:

Step 1. Display the local area code you want to erase (#1 to #5).

Step 2. Press ERASE/CLEAR.

Step 3. Turn the Jog Dial to choose “YES”, and press the Jog Button. A long confirmation beep will sound and the code is erased.


How do you set the day and time on the SONY IT-M804?

To manually set the date and time on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “DATE TIME” appears on the display.

Step 3. Press the Jog Button.

Step 4. Enter the two digits for the month (01 to 12) using the dialing keys, then press the Jog Button.

Step 5. Enter the two digits for the day (01 to 31) using the dialing keys, then press the Jog Button.

Step 6. Enter the two digits for the hour (01 to 12) using the dialing keys, then press the Jog Button.

Step 7. Enter the two digits for the minute (00 to 59) using the dialing keys, then press the Jog Button.

Step 8. Turn the Jog Dial to choose “AM” or “PM”, then press the Jog Button. You will hear a long confirmation beep.


How do you change the display language on the SONY IT-M804?

To change the display language on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “LANGUAGE” (or “IDIOMA”) appears on the display.

Step 3. Press the Jog Button.

Step 4. Turn the Jog Dial to select the desired display language, then press the Jog Button. You will hear a long confirmation beep.


What do the various lamp indications signify on the SONY IT-M804?

The status lamps on the SONY IT-M804 indicate the following conditions:

Lamp / Button Lighting Pattern Status
INTERCOM Lights up Calling extension from your phone or conversation available.
INTERCOM Flashes quickly Receiving an intercom call.
INTERCOM Flashes slowly Other phone using extension.
CONF Lights up Conference function is activated.
NEW CALL Flashes There is new data in the Caller ID list.
MESSAGES Flashes There are voice mail messages.
LOWER Lights up Selecting the second memory of the one-touch dial button.
LINE 1 to 4 Lights up You are using this line.
LINE 1 to 4 Flashes quickly Receiving a call.
LINE 1 to 4 Flashes evenly Call being held on your phone line or transferred call being made.
LINE 1 to 4 Flashes slowly Call being held on other phone line.
LINE 1 to 4 Flashes intermittently Receiving a transferred call.
LINE 1 to 4 Flashes slow pulse Line is used by other phone.
BUSY REDIAL Lights up Busy redial function is activated.
MUTING Lights up Mute function is activated.
DO NOT DISTURB Lights up Do Not Disturb function is activated.
SPEAKERPHONE (HEADSET) Lights up Talking through the speakerphone or headset, paging, or busy redialing.

How do you make an outside call using the SONY IT-M804?

To make a call using the SONY IT-M804:

Step 1. Pick up the handset or press SPEAKERPHONE. “=== TALK ===” appears on the display, followed by the duration timer. The connected line button lights up. To select a specific line beforehand, press LINE 1, LINE 2, LINE 3, or LINE 4.

Step 2. Dial the phone number using the dialing keys.

Step 3. When finished talking, replace the handset in the cradle or press SPEAKERPHONE. The line button goes off.

Note: If a line is on hold, you must press an unused line button first before dialing.


How do you make calls when a headset is connected to the SONY IT-M804?

When an optional headset is connected to the HEADSET jack of the SONY IT-M804:

Step 1. Press SPEAKERPHONE (HEADSET). The SPEAKERPHONE lamp lights up.

Step 2. Dial the phone number.

Step 3. When finished talking, press SPEAKERPHONE (HEADSET). The lamp goes off.


How do you adjust the handset, headset, or speaker volume on the SONY IT-M804?

To adjust the handset or headset volume: During a conversation, press VOLUME (+) or (-). Each press switches the volume between “HIGH”, “MID”, and “LOW”.

To adjust the speakerphone volume: During a speakerphone conversation, press VOLUME (+) or (-). Each press adjusts the speaker volume across 16 different levels.


How do you put a call on hold and resume it on the SONY IT-M804?

To put a call on hold on the SONY IT-M804, press HOLD. The corresponding line button will flash.

To resume the conversation, press the flashing LINE 1, LINE 2, LINE 3, or LINE 4 button. The call can be resumed from any connected phone.

Note: If a call is left on hold for more than about three minutes, an alarm will sound.


How do you mute your voice during a conversation on the SONY IT-M804?

To disable the microphone during a call on the SONY IT-M804, press MUTING. The MUTING lamp lights up.

To resume conversation, press MUTING again.


How do you temporarily switch to tone dialing on the SONY IT-M804?

While using pulse dialing, press the TONE (*) button after you are connected. The line will remain in tone dialing until the call is disconnected.


How do you redial the last number dialed on the SONY IT-M804?

To redial the last number called on the SONY IT-M804:

Step 1. Pick up the handset or press SPEAKERPHONE. Press a line button to select a line if necessary.

Step 2. Press REDIAL/PAUSE. The last number dialed appears on the display and is automatically dialed.


How do you check or erase the last phone number dialed on the SONY IT-M804?

To check the number: While the phone is not in use, press REDIAL/PAUSE. The number appears on the display for 20 seconds. Pick up the handset or press SPEAKERPHONE to dial it.

To erase the number: While the phone is not in use, press REDIAL/PAUSE twice within 20 seconds. The number is erased from memory.


How does the busy redial feature work on the SONY IT-M804?

When the number called is busy, press BUSY REDIAL while the phone is not making a call.

The SONY IT-M804 will automatically redial the last number up to 10 times every 30 seconds until the call connects.

During busy redialing, the BUSY REDIAL, MUTING, SPEAKERPHONE, and selected line lamps light up. The operation is canceled if you press BUSY REDIAL or make/receive another call.


How do you make another call while already talking on the SONY IT-M804?

To make a second call while engaged on a line (for example, on Line 1):

Step 1. Press HOLD while talking. Line 1 is put on hold and its line button flashes slowly.

Step 2. Press an unused line button (such as LINE 2).

Step 3. Dial the phone number for the second party.

To disconnect the second line and return to the first party, press LINE 1.


How do you answer an incoming call on the SONY IT-M804?

When the SONY IT-M804 rings, you can answer by:

Picking up the handset from the cradle, or pressing SPEAKERPHONE.

Alternatively, press the flashing LINE button (LINE 1, LINE 2, LINE 3, or LINE 4) to speak through the speakerphone.

When finished, replace the handset in the cradle or press SPEAKERPHONE.


How do you adjust the ringer volume on the SONY IT-M804?

To adjust the ringer volume on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “RING VOLUME” appears on the display, then press the Jog Button.

Step 3. Turn the Jog Dial to choose “HIGH”, “MID”, “LOW”, or “OFF”, and press the Jog Button.

While the phone is ringing, you can also adjust the ringer volume directly by pressing VOLUME (+) or (-), although it cannot be set to “OFF” this way.


How do you activate and deactivate Do Not Disturb on the SONY IT-M804?

While the phone is idle or ringing, press DO NOT DISTURB. The DO NOT DISTURB lamp lights up, muting outside and intercom ringers as well as voice paging.

To deactivate, press DO NOT DISTURB again. The lamp turns off.

Note: When a call arrives while Do Not Disturb is active, “** RINGING **” is still displayed, and outside calls cannot be transferred to the phone.


How do you answer a second call arriving on another line while talking on the SONY IT-M804?

When another call arrives while you are talking, the corresponding line button flashes and two beeps sound from the speaker:

Step 1. Press HOLD to put the current call on hold.

Step 2. Press the flashing LINE button for the incoming call to speak with the new caller.

To disconnect the new caller and return to the first caller, press the first LINE button.


How do you store phone numbers and names into one-touch dialing on the SONY IT-M804?

The SONY IT-M804 can store up to 16 one-touch numbers (two per button):

Step 1. Press PROGRAM. “DIRECTORY” appears on the display.

Step 2. Select the first memory (ensure LOWER is not lit) or the second memory (press LOWER so it lights up).

Step 3. Press the desired one-touch dial button. “ENTER NAME” appears.

Step 4. Enter the name (up to 15 characters) using the dialing keys. Turn the Jog Dial up to move the cursor right for consecutive letters on the same key or for spaces.

Step 5. Press the Jog Button. “ENTER NUMBER” appears.

Step 6. Enter the telephone number (up to 20 digits, including tone and pause).

Step 7. Press the Jog Button. A long confirmation beep sounds and the entry is stored.


What characters can be entered using the dialing keys on the SONY IT-M804?

Characters can be entered using the keypad on the SONY IT-M804 as follows:

Key Available Characters
1 1
2 A, B, C, 2
3 D, E, F, 3
4 G, H, I, 4
5 J, K, L, 5
6 M, N, O, 6
7 P, Q, R, S, 7
8 T, U, V, 8
9 W, X, Y, Z, 9
0 0
* *
# &, ‘, ,, -, ., #, (space)

How do you change a stored one-touch dial name or number on the SONY IT-M804?

To edit a one-touch entry on the SONY IT-M804:

Step 1. Press the one-touch dial button (or LOWER then the button) to display the entry.

Step 2. Press PROGRAM. The cursor flashes at the first character.

Step 3. Turn the Jog Dial up until the character to change flashes, then enter the new character.

Step 4. Press the Jog Button to display the phone number.

Step 5. Enter the new phone number using the dialing keys if needed.

Step 6. Press the Jog Button. A long confirmation beep confirms the changes.


How do you erase a one-touch dial number on the SONY IT-M804?

To erase a one-touch dial memory on the SONY IT-M804:

Step 1. Display the stored name and number by pressing the one-touch dial button.

Step 2. Press ERASE/CLEAR.

Step 3. Turn the Jog Dial to choose “YES”, then press the Jog Button. A long confirmation beep will sound.


How do you place a call using one-touch dialing on the SONY IT-M804?

To dial using one-touch buttons on the SONY IT-M804:

Step 1. Pick up the handset or press SPEAKERPHONE. (If accessing the second memory, press LOWER).

Step 2. Press the desired one-touch dial button. The stored number will be dialed automatically.


How do you store names and numbers in the Phone Directory on the SONY IT-M804?

To store an entry in the Phone Directory of the SONY IT-M804 (up to 100 entries):

Step 1. Press PROGRAM. “DIRECTORY” appears on the display.

Step 2. Press the Jog Button. “ENTER NAME” appears.

Step 3. Enter the name (up to 15 characters) using the dialing keys. Turn the Jog Dial up to move the cursor right when needed.

Step 4. Press the Jog Button. “ENTER NUMBER” appears.

Step 5. Enter the telephone number (up to 20 digits).

Step 6. Press the Jog Button. A long confirmation beep sounds and the entry is saved.

Note: A combined total of 200 names and numbers can be stored in the Caller ID list and Phone Directory combined.


How do you make a call from the Phone Directory on the SONY IT-M804?

To call from the Phone Directory on the SONY IT-M804:

Step 1. Press the Jog Button. “DIRECTORY 1” appears on the display.

Step 2. Search for the desired entry by turning the Jog Dial up or down, or by pressing the dialing key of the initial letter and turning the Jog Dial.

Step 3. Pick up the handset, press SPEAKERPHONE, or press the Jog Button. The displayed phone number will be dialed.


How do you enable and set the Phone Directory security code on the SONY IT-M804?

To secure the Phone Directory on the SONY IT-M804:

Step 1. Press PROGRAM.

Step 2. Turn the Jog Dial up until “SECURITY MODE” appears on the display.

Step 3. Press the Jog Button. “NUMBER=????” appears.

Step 4. Enter a four-digit security code (0000 to 9999) using the dialing keys.

Step 5. Press the Jog Button.

Step 6. Turn the Jog Dial to choose “ON”, then press the Jog Button. A long confirmation beep will sound.


How do you change the Phone Directory security code on the SONY IT-M804?

To change an existing security code on the SONY IT-M804:

Step 1. Press PROGRAM, scroll to “SECURITY MODE”, and press the Jog Button.

Step 2. Enter the current four-digit security code. “CHANGE? YES NO” appears.

Step 3. Turn the Jog Dial to choose “YES”, and press the Jog Button.

Step 4. Enter a new four-digit security code using the dialing keys.

Step 5. Press the Jog Button.

Step 6. Turn the Jog Dial to choose “ON” or “OFF”, then press the Jog Button.


How do you initiate a three-way conference call on the SONY IT-M804?

To initiate a three-way conference call while talking on one line with the SONY IT-M804:

Step 1. Press HOLD while talking on the first line. The line is placed on hold.

Step 2. Press another unused LINE button (LINE 1, 2, 3, or 4).

Step 3. Dial the phone number for the second party.

Step 4. Press CONF once connected to the second party. The CONF lamp lights up, allowing all three parties to converse.

To return to a standard two-party call, press the line button of the party you wish to keep speaking with.


How do you add an incoming call to create a three-way conference call on the SONY IT-M804?

If another call arrives while you are on a call with the SONY IT-M804:

Step 1. Press HOLD. The line in use is put on hold.

Step 2. Press the flashing LINE button where the incoming call is arriving.

Step 3. Press CONF. All three parties are connected in conference.


How do you manage calls on hold or disconnect lines during a conference call on the SONY IT-M804?

To disconnect both lines simultaneously: Replace the handset in the cradle, or press SPEAKERPHONE (HEADSET).

To disconnect one line and keep the other: Press the LINE button of the call you want to continue.

To put both lines on hold: Press HOLD. Press CONF to resume talking with both parties, or press a single LINE button to resume only that line.


What does the memory match function do on the SONY IT-M804?

If you receive an incoming call from a number that matches an entry stored in one-touch dialing or the Phone Directory of the SONY IT-M804, the ringer changes to a higher pitch tone starting from the second ring.


How do you view entries in the Caller ID list on the SONY IT-M804?

To review Caller ID records on the SONY IT-M804:

Step 1. Turn the Jog Dial while the phone is idle. Data for the newest call appears for 20 seconds.

Step 2. Turn the Jog Dial up to view older records, or turn it down to view newer records.

When all data has been reviewed, “END OF LIST” appears. The NEW CALL lamp flashes when new unviewed calls exist.


What do the “REPEAT” and “SAVE” indicators mean in the Caller ID list of the SONY IT-M804?

“REPEAT” appears when more than one call has been received from the same caller. Older data is replaced by newer data, counted as one new call until viewed.

“SAVE” indicates that the call record has been locked and saved so that it is protected from automatic overwriting when the 200-call memory is filled.


How do you save a number in the Caller ID list on the SONY IT-M804?

You can protect up to 50 phone numbers from being automatically erased when new calls arrive:

Step 1. Display the desired Caller ID entry by turning the Jog Dial.

Step 2. Press PROGRAM while the number is displayed.

Step 3. Turn the Jog Dial to choose “SAVE”, then press the Jog Button. A long confirmation beep sounds and “SAVE” appears on the display.


How do you erase entries from the Caller ID list on the SONY IT-M804?

To erase entries one by one: Display the number with the Jog Dial, press ERASE/CLEAR, turn the Jog Dial to choose “YES”, and press the Jog Button.

To erase the entire list at once: Turn the Jog Dial until “END OF LIST” appears, press ERASE/CLEAR (“ERASE ALL?” displays), turn the Jog Dial to choose “YES”, and press the Jog Button.

Note: The entire list cannot be erased if new unviewed calls remain. “Saved” records are protected and must be deleted individually.


How do you call back a number directly from the Caller ID list on the SONY IT-M804?

To call back a number using Caller ID on the SONY IT-M804:

Step 1. Display the phone number you want to call by turning the Jog Dial.

Step 2. Press the Jog Button, pick up the handset, or press SPEAKERPHONE while the number is displayed. The phone dials the displayed number automatically.


How do you change the number of digits of a phone number in the Caller ID list on the SONY IT-M804?

While the phone number from the Caller ID list is displayed on the SONY IT-M804, press the # button repeatedly until the number displays with the desired format (such as 7 digits, 10 digits with area code, or 11 digits with 1 + area code).

Once adjusted, you can dial or store the number directly.


How do you store a Caller ID number into a one-touch dial button on the SONY IT-M804?

To store a Caller ID record into a one-touch button on the SONY IT-M804:

Step 1. Display the number by turning the Jog Dial.

Step 2. Press PROGRAM while the number is displayed.

Step 3. Press the Jog Button. (Press LOWER if saving to the secondary memory).

Step 4. Press the desired one-touch dial button. A long confirmation beep will sound.


How do you copy a Caller ID number into the Phone Directory on the SONY IT-M804?

To copy a Caller ID entry to the Phone Directory on the SONY IT-M804:

Step 1. Display the number by turning the Jog Dial.

Step 2. Press PROGRAM while the number is displayed.

Step 3. Press the Jog Button.

Step 4. Press the Jog Button again. A long confirmation beep will sound confirming the entry is stored.


How do you use Caller ID with call waiting on the SONY IT-M804?

When you subscribe to combined “Caller ID with call waiting” service, the incoming caller’s information appears on the display for approximately 20 seconds while you are talking.

To switch to the new caller, press CALL WAITING/FLASH.

To switch back to the original caller, press CALL WAITING/FLASH again.


How does the visual message waiting service work on the SONY IT-M804?

When you have voice mail messages waiting on a line, “LINE X” and “MESSAGES” appear on the display of all phones connected to LINE 1, and the MESSAGES lamp flashes.

The indicator clears when messages are retrieved. If it remains flashing after retrieving messages on another device, press ERASE/CLEAR to turn it off manually.


How do you place an intercom call to another phone on the SONY IT-M804?

To call another internal extension using the SONY IT-M804:

Step 1. Pick up the handset (or press SPEAKERPHONE).

Step 2. Press INTERCOM. “INTERCOM ??” appears on the display.

Step 3. Enter the two-digit station number (01 to 16) using the dialing keys. The phone calls immediately and the receiving phone rings.

Step 4. When the other party answers, converse normally. Replace the handset in the cradle when finished.


How do you voice page a specific phone on the SONY IT-M804?

Voice paging turns on the speakerphone of the paged phone automatically without the recipient pressing any buttons:

Step 1. Pick up the handset.

Step 2. Press PAGE. “PAGE ??” appears on the display.

Step 3. Enter the two-digit station number (01 to 16) using the dialing keys. The called phone rings once and its speakerphone turns on automatically.

Step 4. Speak your message. Replace the handset when finished.


How do you page all connected phones simultaneously on the SONY IT-M804?

To broadcast an announcement to all connected phones:

Step 1. Pick up the handset.

Step 2. Press ALL PAGE. “ALL PAGE” appears on your display. All available phones ring once and turn on their speakerphones.

Step 3. Speak your announcement. Replace the handset in the cradle when finished.

Note: Phones that are on an outside call or in Do Not Disturb mode will not be paged.


How do you conduct an intercom conference call on the SONY IT-M804?

To bring an internal intercom party into an ongoing outside call:

Step 1. While talking with an outside caller, press INTERCOM. The outside line is placed on hold.

Step 2. Enter the two-digit station number (01 to 16) of the internal party.

Step 3. When the internal party answers, press CONF. The CONF lamp lights up, connecting all three parties.


How do you transfer an outside call to another extension on the SONY IT-M804?

To transfer an active call using the SONY IT-M804:

Step 1. While conversing with an outside caller, press TRANSFER. The outside call is put on hold and “TRANSFER ??” appears.

Step 2. Enter the two-digit station number (01 to 16) of the receiving phone. You can replace the handset immediately or wait.

Step 3. When the receiving extension picks up the handset or presses the flashing LINE button, the outside call is transferred.

Note: If the transferred call is not answered within approximately one minute, an alert alarm will sound at the transferring phone.


How do you mount the SONY IT-M804 on a wall?

To mount the SONY IT-M804 to a wall plate:

Step 1. Remove the handset hang-up tab from the cradle and replace it upside down so the tab holds the handset in place.

Step 2. Attach the wall bracket to the phone by inserting the upper tabs first, then pressing the phone into the lower tabs until secured.

Step 3. Attach the AC power adaptor cord and telephone line cords into the brackets routing grooves.

Step 4. Plug the cords into the jacks on the phone.

Step 5. Hook the wall bracket onto the wall plate studs and connect the line cords to the wall telephone outlets.


How does the SONY IT-M804 function during a power failure, and which backup battery is required?

The SONY IT-M804 requires an optional 6F22/6LR61 9V battery for power failure backup:

With the battery installed, you can make and receive calls for approximately 30 minutes continuously during a power outage.

The speakerphone does not work during a power outage. To make or receive a call, pick up the handset and press the desired or flashing LINE button.

“POWER FAILURE” will appear on the display during an outage.


How should the cabinet of the SONY IT-M804 be cleaned and maintained?

Clean the cabinets of the SONY IT-M804 with a soft cloth slightly moistened with water or a mild detergent solution.

Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine, as these may damage the finish of the cabinet.


What should you do if you hear no dial tone on the SONY IT-M804?

Ensure that the telephone line cord is securely connected to both the SONY IT-M804 jack and the telephone wall outlet.


What should you do if the SONY IT-M804 fails to ring on incoming calls?

Check the following troubleshooting steps on the SONY IT-M804:

Ensure that the “RING VOLUME” is set to “HIGH”, “MID”, or “LOW” and not set to “OFF”.

Make sure the phone is not in Do Not Disturb mode (the DO NOT DISTURB lamp should be off).


How do you hardware reset the SONY IT-M804?

If the SONY IT-M804 is not operating properly and troubleshooting remedies fail:

Unplug the AC power adaptor. If a backup battery is installed, remove it.

If the phone still will not reset, press the RESET button located on the left side of the phone using the tip of a ball-point pen.

Note: The day and time setting and the last dialed number will be erased upon reset.


How do you restore the SONY IT-M804 to its factory default settings?

To restore all settings and erase stored memory (such as lost security codes or home area codes) on the SONY IT-M804:

Step 1. Unplug the AC power adaptor. If a 9V battery is installed, remove it first.

Step 2. Press and hold ERASE/CLEAR while plugging the AC power adaptor back into the AC outlet.

Note: Returning to factory settings will erase all stored entries in one-touch dialing, the Phone Directory, the Caller ID list, and custom settings.


What are the technical specifications of the SONY IT-M804?

The technical specifications of the SONY IT-M804 are:

Power source: DC 12V from supplied AC power adaptor AC-T71.

Dial signal: Tone, 10 PPS (pulse) selectable.

Dimensions: Approximately 7 7/8 x 2 5/8 x 9 1/4 inches (199 x 68.2 x 235.5 mm) (width/height/depth).

Mass: Approximately 2 lb 2 oz (1010 g).


CLICK HERE TO DOWNLOAD SONY IT-M804 (01) PDF DOCUMENT


Leave comments, questions, reviews, tips, tricks, hacks or page errors below. Account not required.