SONY EMARKER EMK-01 (01) PDF Document

To use the SONY EMARKER EMK-01, the following are required:

• IBM-compatible PC

– Pentium 133 MHz (200 MHz or faster is recommended)

– 32MBytes of RAM (64MBytes or greater is recommended)

– 3MBytes of available hard disk space (5MBytes is recommended)

– SVGA (800 × 600) monitor with 256 colors (XGA 1024 × 768 is recommended)

• U.S.-Version Windows 98 or Windows 98 SE (Second Edition)

• USB port

• Internet access (e.g. modem or Ethernet) with speed of 28.8kbps or greater

• Internet browser

– Internet Explorer 4.0 or newer, or

– Netscape Navigator 4.0 or newer

1. Turn to open the battery compartment lid using a coin, etc.

2. Place the supplied CR2025 battery with the + side facing upward.

3. Close the lid.

Yes. All your eMarks will be erased when you open the battery compartment. Be sure to upload your eMarks before opening the lid.

Under normal conditions of use, the battery will last approximately 6 months. When the battery becomes weak, the LCD indications become dimmer. Replace the battery with a Sony CR2025 or Duracell DL-2025 lithium battery. Use of another battery may present a risk of fire or explosion.

1. Connect the SONY EMARKER EMK-01 Cradle to the USB port of your PC.

2. Download and install the eMarker software. Follow the downloading and installing procedure.

3. Take off the cap of the eMarker.

4. Plug the eMarker into the Cradle. In some cases, you can plug the eMarker directly into the USB port on your PC as well.

5. Your PC will recognize the eMarker and install the device driver automatically.

6. Register your eMarker by following the registering procedure.

7. Unplug the eMarker from the Cradle. Be sure to attach the cap to the eMarker after use.

Press the e button once when you hear a song that you like on one of your registered radio stations. A black circle appears on the display in a falling down “Sand Clock” animation movement.

Press the e button twice. “TV” flashes on the lower display of the eMarker. Be sure to check the availability of this feature.

Hold the e button pressed for two seconds. “ROAM” flashes on the lower display of the eMarker. Be sure to check the availability of this feature.

1. Turn on your PC and establish an internet connection.

2. Take off the cap of the eMarker.

3. Plug the eMarker into the eMarker Cradle.

4. Continue the operation following the instructions on your PC.

The eMarker can hold up to 10 eMarks at once. If you try to register an 11th eMark, all 10 black circles will flash to indicate that it is full and the 11th eMark will not be registered.

Press the CANCEL button on the rear of the eMarker with the tip of a pen or sharp object. Each time you press the CANCEL button, an eMark is canceled from the latest one entered, and one black circle on the display disappears.

• The eMarker is a precision instrument. Never disassemble.

• Keep the eMarker away from extremely high temperatures (above 60°C [140 °F]) and humidity. Never leave the eMarker inside a car.

• When using outdoors, never let the eMarker become wet with rain or salt water.

• When the eMarker or the connector become soiled, wipe them with a dry cloth.

• Do not pull the cable when disconnecting the cable of the eMarker cradle from your PC. Always grip the plug when disconnecting to prevent damage.

• Do not try to pull the cap off without pushing the two buttons on the cap.

• The battery may not be set properly. Set the battery properly.

• Ten eMarks may have already been made. Cancel the eMarks and try eMarking again or upload your eMarks to the computer to clear the memory in the terminal.

• Installation may have failed or the shortcut for the application has been erased. Create a shortcut for the tsr.exe file in the folder in which the application is installed, and move it to the Startup Folder by going through Start Menu and selecting Program Folder.

• The tsr.exe file for the application may be erased. Download and install the application again.

• If the “e” logo does not appear on the Task Tray (at lower right-hand corner of screen), launch the eMarker application by going through the folder in which the application is installed.

• Check to see if your USB port is active by switching it with another device (e.g. a USB mouse).