SONY DREAM MACHINE ICF-CD823 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD SONY DREAM MACHINE ICF-CD823 (01) PDF MANUAL


PDF Content Summary: 3-046-170-21 (1) FM/AM CD Clock Radio Operating Instructions Dream Machine is a trademark of Sony Corporation. ICF-CD823 Sony Corporation © 2000 Printed in Malaysia LIM(Portable ITED WAARRAudio) NTY Owner’s Record The model number and the serial number are located on the bottom. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. ICF-CD823 Serial No. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instruc- tions in the literature accompanying the appliance. ∗ The graphical symbols are on the bottom of the enclosure. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. CAUTION The use of optical instruments with this product will increase eye hazard. Before You Begin Thank you for choosing the Sony CD clock radio! It will give you many hours of reliable service and listening pleasure. Before operating the unit, please read these instructions thoroughly and retain them for future reference. Features • Built-in CD Player with Shuffle/Repeat function. • You can wake up to any track of a CD. • PLL (Phase Locked Loop) Synthesized Tuner with 5 random memory presets for easy one button tuning. • Dual alarm. • Alarm setting dial—easy to set alarm time and modes. • Extendable snooze—snooze time can be extended from 8 to 60 minutes in maximum every time you use. • Summer time (daylight saving time) calculation. Precautions • Operate the unit on the power source specified in the “Specifications.” • The nameplate indicating operating voltage, etc. is located on the bottom of the unit. • To disconnect the power cord (mains lead), pull it out by the plug, not the cord. • Do not leave the unit in a location near a heat source such as a radiator or airduct, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock. • Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on a surface (a rug, a blanket, etc.) or near materials (a curtain) which might block the ventilation holes. • Should any solid object or liquid fall into the unit, unplug the unit and have it checked by a qualified personnel before operating it any further. • When the casing becomes soiled, clean it with a soft cloth dampened with mild detergent solution. Never use abrasive cleansers or chemical solvents, as they may mar the casing. If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. Troubleshooting Should any problem occur with the unit, make the following checks to determine whether or not servicing is required. If the problem persists, consult the nearest Sony dealer. The clock does not show the correct time. • Has an electrical power outage lasting more than one minute occurred? The CD, radio or buzzer alarm does not sound at the preset alarm time. • Is the alarm setting dial set to the desired ALARM MODE? The radio alarm is activated but no sound comes on at the preset alarm time. • Has a station been preset onto preset button 1? • Has VOLUME been adjusted ? The CD player does not operate. • Did you close the CD lid? • Did you place the disc correctly? The disc should be placed with the labeled side up. • Dusty or defective disc—Clean the disc with an optional cleaning cloth. Wipe the disc from the center out. • Take out the CD and leave the CD compartment open for about an hour to get rid of moisture condensation. Sporadic loss of sound in CD operation. • Dusty or defective disc—Clean or replace the disc. • Volume too high—Reduce the volume. • Strong vibration. No sound comes from the speakers. • Hasn't the alarm setting dial been remained setting to ALARM TIME SET? Specifications CD player section System: Compact disc digital audio system Laser diode properties: Material: GaAlAs Wavelength: 780 nm Emission duration: Continuous Laser output: Less than 44.6 μW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7mm aperture.) Frequency response: 20-20,000 Hz +1 dB –1.5 Wow and flutter: Below measurable limit Radio section Frequency range: FM: 87.5-108 MHz AM: 530-1,710 kHz Channel step: FM: 0.1 MHz (fixed) AM: 10 kHz (fixed) General Time display: 12-hour system Speaker: 77 mm (3 1/8 inches) dia., 8 Ω Power outputs: 1.2W + 1.2W (at 10% harmonic distortion) Power requirements: 120 V AC, 60 Hz Dimensions: Approx. 250 × 153 × 207 mm(w/h/d) (Approx. 9 7/8 × 6 1/8 × 8 1/4 inches) incl. projecting parts and controls Mass:Approx. 1,700 g (3 lb 12 oz) Design and specifications are subject to change without notice. IMPORTANT SAFEGUARDS For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the appliance and described in the operating instructions supplied with the appliance by Sony. INSTALLATION Water and Moisture Do not install the appliance near water: for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Heat Do not install the appliance near sources of heat such as radiators, heat registers, stoves, or other appliances that produce heat. Ventilation Slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable and safe operation of the appliance, and to protect it from overheating, these slots and openings must never be blocked or covered. Do not place the appliance on a bed, sofa, rug or other similar surface which may block the slots and openings. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet, unless proper ventilation is provided. Carts and Stands Do not install the appliance on an unstable table, shelf, cart or stand. Use only a cart or stand recommended by Sony. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Wall or Ceiling Mounting If your appliance can be mounted to a wall or ceiling, mount it only as recommended by Sony. USE Power Source Connect the appliance to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarization Do not defeat the grounding or polarization feature of the AC power cord. If your AC receptacle will not accept the power cord plug, contact your electrician to install a proper AC receptacle. AC Receptacle Check to make sure that the AC receptacle holds the power cord plug firmly and securely. If the power cord plug is loose, contact your electrician to replace the defective and unsafe AC receptacle. Power-Cord Protection Route the power cord so that it is not likely to be walked on or pinched by having objects placed on it, paying particular attention to the plugs, receptacles, and the point where the cord exits from the appliance. When not in use Unplug the power cord of the appliance from the outlet when left unused for a long period of time. To disconnect the cord, pull it out by grasping the plug. Never pull the plug out by the cord. Foreign Objects Be careful that foreign objects and liquids do not enter the enclosure through openings. Cleaning Clean the appliance only as recommended by Sony. ANTENNAS Outdoor Antenna Grounding If an outdoor antenna or cable system is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits. WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Antenna Grounding According to the National Electrical Code SERVICE Unplug the appliance from the wall outlet and consult qualified service personnel when: -the power cord or the plug has been damaged. -a solid object or liquid has fallen into the cabinet. -the appliance has been exposed to rain or moisture. -the appliance does not appear to operate normally or exhibits a marked change in performance. -the appliance has been dropped, or the enclosure damaged. Do not attempt to service the appliance beyond that described in the operating instructions. For all other servicing refer to qualified service personnel only. Antenna Lead-in Wire Ground Clamps Antenna Discharge Unit (NEC* Section 810-20) Grounding Conductors Electric Service (NEC* Section 810-21) Equipment Ground Clamps Power Service Grounding —NEC National Electrical Code— Electrode System (NEC* Art 250 Part H) Alarm setting dial To •To handle compact discs Setting the Clock Correct and Date Handle the disc Set the Wake Up Track 1 Press WAKE UP TRACK for a few 1 Set the alarm setting dial to ALARM by its edge. MODE OFF. 2 Plug in the clock radio. The display will flash “AM 12:00”. Incorrect 3 Press CLOCK for a few seconds. Do not touch the You will hear a beep and the year will start to surface. seconds until you hear a beep. The track number flashes on the display. 2 Press TUNING + or – to select the desired track number. The track number can be set up to 99. 3 Press WAKE UP TRACK again. flash in the display. Two short beeps sound to confirm the 4 Press CLOCK + or – until the correct setting. year appears in the display. 5 Press CLOCK once. Do not stick paper or tape nor write anything on the To Check the Alarm Time 6 Repeat steps 4 and 5 to set the month, Press ALARM TIME CHECK. day, hour, and minute. The display shows the alarm time for a After setting the minute, press CLOCK to start the counting of the seconds, and you will hear two short beeps. surface. Note If you press CD u when there is no disc in the CD compartment, “00” flashes for about 5 seconds on the display and the unit turns off few seconds and then returns to show the current time. automatically. When the alarm setting dial is set to either • To display the year and date, press SNOOZE/ ALARM MODE OFF or ALARM MODE DATE/SLEEP OFF once for the date, and within 2 seconds press it again for the year. The display shows the date or year for a few Various Modes of CD Playback A+B, the alarm time in ALARM MODE A and then ALARM MODE B appears in seconds and then changes back to the current You can play tracks repeatedly or in random the display. time. order. • Alarm time in ALARM MODE A and ALARM • To set the current time rapidly, hold down CLOCK + or –. Press CD PLAY MODE. MODE B is set at AM 12:00 when you purchased the unit. • In step 6, when you press CLOCK after the Each press changes the play mode as minute setting to activate the clock, the seconds start counting from zero. follows: ALARM ON— When the alarm comes on at the preset time, • When the alarm setting dial is set to ALARM TIME SET A or B, the clock cannot be set. Display Play indication mode “ ”, “ ”, or “ ” flashes in the display. To change the display to the none (normal play) daylight saving time (summer time) All the tracks are played once. For the buzzer alarm, the beeping of the alarm becomes more rapid after every few seconds in five progressive stages. indication m • When CD and radio, or buzzer alarms are set Press D.S.T./SUMMER T. “REP 1” (single repeat) for the same time, and you choose ALARM “ ” is displayed and the time indication A single track is played repeatedly. MODE A + B, the CD alarm takes precedence. changes to summer time. To deactivate the summer time function, press D.S.T./SUMMER T. again. m “REP ALL” (all repeat) All the tracks are played repeatedly. Note If you set the CD alarm and there is no disc in the CD player, the buzzer alarm will sound in its m place at the time set. Playing a CD “SHUFFLE” (shuffle play) All the tracks are played once An 8 cm (3-inch) CD can be played without an in random order. adaptor. m 1 Push OPEN/CLOSE to open the CD “SHUFFLE REP” (shuffle repeat) All the tracks are played repeatedly compartment lid and place a disc. in random order. To Doze for a Few More Minutes Press SNOOZE/DATE/SLEEP OFF. The CD, radio or buzzer alarm turns off but will be automatically activated again after about 8 minutes. Every time you press SNOOZE/DATE/ 2 Close the CD compartment lid. SLEEP OFF, the snooze time changes as follows: Playing the Radio Manual Tuning The display shows the snooze time for a few seconds and returns to show the current time. 1 Press RADIO•SLEEP to turn on the radio. “RADIO” appears in the display. The display shows the band and frequency for a few seconds and then changes back to 2 the Press current BAND time. repeatedly to select the desired band. 3 Use TUNING + or – to tune in to the desired station. When you press SNOOZE/DATE/SLEEP OFF after the current time appeared, the snooze time starts from 8 minutes again. • The maximum length of the snooze time is 60 minutes. ALARM OFF— The alarm is turned off automatically after 60 minutes. To Stop the Alarm The FM frequency advances or reverses in 0.1MHz channel steps and the AM frequency in 10kHz channel steps. 3 Press CD u. Two short beeps sound when the minimum frequency of each band is received during Press OFF•ALARM RESET to turn off the alarm. The alarm will come on again at the same time the next day. “CD N” and “01” appear on the display to indicate that track 1 of the CD is playing. 4 tuning. Adjust volume using VOLUME. To Cancel the Alarm 4 Turn VOLUME to adjust the volume. • To turn off the radio, press OFF•ALARM RESET. Set the alarm setting dial to ALARM MODE OFF. To Press Pause CD u Setting the Sleep Timer You can enjoy falling asleep to the radio using the built-in sleep timer that turns off the radio automatically after a preset duration. Press RADIO•SLEEP. The radio turns on. You can set the sleep timer to durations of 90, 60, 30, or 15 minutes. Every push changes the display as follows: Two short beeps sound when the display returns to “On”. “SLEEP” will appear in the display when the duration time is set. The radio will play for the time you set, then shut off. • To turn off the radio before the preset time, press SNOOZE/DATE/SLEEP OFF. To Use Both the Sleep Timer and the Alarm You can enjoy falling asleep to the radio and be awakened by the CD, radio or buzzer alarm. 1 Set the alarm. (See “Setting the Alarm”.) 2 Set the sleep timer. (See “Setting the Sleep Timer”.) • To improve radio reception FM: Extend the FM wire antenna fully to increase reception sensitivity. Resume play after CD u again AM: Rotate the unit horizontally for optimum pause reception. A ferrite bar antenna is built Locate the beginning .** into the unit. of the current track (AMS*) Do not operate the unit over a steel desk or metal surface, as this may lead to Locate the next >** interference of reception. track (AMS) • To check the station being received, press Go back at high speed Hold down .** TUNING + or – lightly. The display shows the Go forward at high Hold down >** speed Locate the previous . repeatedly** track (AMS) band and frequency for a few seconds and then changes back to the current time. • If the radio alarm comes on while the radio is on, the unit switches to the station on preset button 1 (WAKE UP STATION). Locate the succeeding > repeatedly** track (AMS) Preset Tuning Stop play OFF•ALARM RESET You can preset up to 5 stations; one station for * AMS = Automatic Music Sensor each preset buttons 1 to 5, for one-touch tuning. **These operations are possible during both play Presetting a station and pause. Example: To preset AM 1260 kHz onto preset button 2. 1 Press RADIO•SLEEP to turn on the radio. 2 Tune in to the station on AM 1260 kHz (See “Manual Tuning”). 3 Hold down the desired STATION•SELECT/PRESET button (in this case, 2) until you hear two short beeps. The display shows the frequency for a few seconds and then changes back to the current time. For the radio alarm, preset the station to be used as the alarm onto preset button 1. To change a preset station Tune in manually to the station you want to store and hold down the preset button until you hear two short beeps. The previously stored station will be replaced by the new one. Tuning in to a preset station 1 Press RADIO•SLEEP to turn on the radio. 2 Press the STATION•SELECT/PRESET button where the desired station is stored. 3 Adjust the volume using VOLUME. After a few seconds, the display returns to the current time but the preset button number remains. FM wire antenna Setting the Alarm This radio is equipped with 3 alarm modes — CD, radio and buzzer. Before setting the alarm, AC power cord make sure to set the clock (see “Setting the Clock”). To Set the Alarm Time < To set the alarm: 1 Set the alarm setting dial to ALARM TIME SET A (CD). After one beep, “ ” and the alarm time set in the previous time will flash in the display. 2 Press CLOCK + or – until the desired time appears. When CLOCK + or – is held down, the displayed time initially changes in one- minute steps, and after a few seconds, switches to ten-minute steps. 3 Set the alarm setting dial to ALARM MODE OFF. Two short beeps will confirm the setting. To set the or alarm: 8 16 1 Set the alarm setting dial to ALARM 48 56 60 TIME SET B (radio or buzzer). After one beep, “ ” or “ ” and the alarm time set in the previous time will flash in the display. 2 Press CLOCK + or – until the desired time appears. When CLOCK + or – is held down, the displayed time initially changes in one- minute steps, and after a few seconds, switches to ten-minute steps. 3 Set the alarm setting dial to ALARM MODE OFF. Two short beeps will confirm the setting. • When the alarm setting dial is set to ALARM TIME SET A or B, the sound of the CD or the radio will be interrupted. To Set the Alarm Mode Before setting the alarm mode, be sure to set the alarm time. (See “To Set the Alarm Time”.) Set the alarm setting dial to the desired alarm mode (A, B, or A+B). When the alarm setting dial is set to ALARM MODE B or A+B, you can choose or by switching the modes in ALARM B. According to the alarm mode that you set, , , or will appear in the display. When the radio alarm is activated, the radio station that is preset on the preset button 1 (WAKE UP STATION) turns on at the preset time. For the radio alarm, make sure you have preset a radio station onto preset button 1 (See “Preset Tuning”). 24 32 Push 40 Labeled surface up Close the lid Alarm Set the alarm setting dial to Set ALARM B to Display On 90 60 CD ALARM MODE A –––––– 15 30 Radio ALARM MODE B RADIO Buzzer ALARM MODE B BUZZER CD and ALARM MODE Radio A + B RADIO CD and ALARM MODE Buzzer A + B BUZZER


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply