SONY CDX-1300 (02) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD SONY CDX-1300 (02) PDF MANUAL


PDF Content Summary: SONY Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 18 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 1 % total harmonic distortion. W General Outputs FM/AM Compact Disc Player Other specifications CD player section System Compact disc digital audiu system Signal-to-noise ratio 90 dB Frequency response 10 - 20,000 Hz Wow and flutter Below measurable limit Laser Diode Properties Material GaAs + GaAlAs Wavelength 785 ~ 815 nm (Typ 800 nm) Emission Duration Continuous Laser output power Less than 0 5 mW* * This output is the value measured at a distance of 0 7 mm from the objective lens surface on the Optical Pick-up Block Tone controls Power requirements Dimensions Audio output Power amplifier control Power antenna relay control Bass +8 dB at 100 Hz Treble 18 dB at 10 kHz 12 V DC car battery (negative ground) Approx 178x50x178 mm (7178x2x71/8 in ) (w/h/d) Approx 182 x 53 x 162 mm (71/4x21/8X61/2 in ) (w/h/d) Approx 1 2 kg (2 lb 10 oz) Parts for installation and connections (1 set) Compact disc single adapter CSA-8 Operating Instructions Mounting dimensions Mass Supplied accessories Tuner section o FM Optional accessories Design and specifications are subject to change without notice Tuning range 87 5 - 107 9 MHZ Antenna terminal External antenna connector Intermediate frequency 107 MHZ Usable sensitivity 12 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 65 dB (stereo), 68 dB (mono) Harmonic distortion at 1 kHz 07% (stereo), 05 % (mono) Separation 35 dB at 1 kHz Frequency response 30 - 15,000 Hz Owner's Record The model and serial numbers are located on the bottom of the unit Record the serial number in the space provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No CDX-1300 Serial No AM Tuning range Antenna terminal Intermediate frequency Sensitivity 530 - 1,710 kHz External antenna connector 107 MHz/450 kHz 30 V For installation and connections, see the supplied installation/connections manual ...... .: Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4-8 ohms Maximum power output 45 W X4 (at 4 ohms) COMPACT disc DIGITAL AUDIO CDX-1300 Sony Corporation ©2000 Printed in Japan Warning Welcome! Getting Started Thank you for purchasing the Sony Compact Disc Player This unit lets you enjoy a variety of features Resetting the unit Before operating the unit for the first time or after replacing the car battery, you must reset the unit Remove the front panel and press the reset button with a pointed object, such as a ball-point pen Notes • Be sure not to drop the panel when detaching it from the unit • If you detach the panel while the unit is still turned on, the power will turn off automatically to prevent the speakers from being damaged • When carrying the front panel with you, use the supplied front panel case Attaching the front panel Attach part of the front panel to part of the unit as illustrated and push the left side into position until it clicks This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/ TV technician for help Reset button Notes • Pressing the reset button will erase the clock setting and some memorized program and memory functions . When you connect the power supply cord to the unit or reset the unit, wait for about 10 seconds before you insert a disc If you insert a disc within these 10 seconds, the unit will not be reset, and you will have to press the reset button again You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment Detaching the front panel You can detach the front panel of this unit to prevent the unit from being stolen Notes . Be sure not to attach the front panel upside down • Do not press the front panel too hard against the unit when attaching it . Do not press too hard or put excessive pressure on the display window of the front panel • Do not expose the front panel to direct sunlight or heat sources such as hot air ducts, and do not leave it in a humid place Never leave it on the dashboard of a car parked in direct sunlight or where there may be a considerable rise in temperature CAUTION The use of optical instruments with this product will increase eye hazard 1 Press OFF 2 Press RELEASE, then slide the front panel a little to the left, and pull it off towards you OFF Caution alarm If you turn the car ignition off without removing the front panel, the caution alarm will beep for a few seconds If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated RELEASE ILUL V 1 Sony on line http //www world sony com/ 3 - 1 1 * Location of controls 1 2 3 Radio 5 6 7 Setting the clock The clock has a 12-hour digital indication Example: To set the clock to 10:08 1 Press DSPL during operation :: wwwwww w . ww. .... .. . .. .. . .....::: T V sur - main mw ... . . .3 2 Press OSPL for two seconds In ..1.111 usuri w w. .1.8W. Lw.yompasware . ! - LiwITPiri Ni. w ... Vin w ...TAwww wwwNTPISIV . LAW.LIXIRULUAN... WAV.U.ALLAV... WATAWAVA M AA w wwwwww w wwww VAY ..w. WAUAWAWAL USUAMINI WANAWATAWANYIMWA MAMA Www WALAY WWwwwwwwwwwww Memorizing stations automatically -- Best Tuning Memory (BTM) This unit selects the stations with the strongest signals and memorizes them in the order of their frequencies You can store up to 6 stations on each band (FM I, FM II, FM III, and AM) www . The hour indication flashes AS leo S123456 osoba) OFF 1- w ood Set the hour RESES CDX-1300 To go forward Caution When tuning in stations while driving, use Best Tuning Memory to prevent accidents 8 9 10 11 12 13 14 15 To go backward 1 Press SOURCE repeatedly to select the tuner Each time you press SOURCE, the mode changes as follows: CD + TUNER 2 Press SOUND 1 MODE (band select) button 2 SOURCE (source select) button 3 (volume/bass/treble/left-right/ front-rear control) button 4 Display window 5 SEEK/AMS (seek/Automatic Music Sensor/ manual search) button 6 4 (eject) button 7 SENS/BTM (sensitivity adjust/Best Tuning Memory) button 8 D-BASS button 9 RELEASE (front panel release) button 10 SOUND button 11 Reset button (located on the front side of the unit hidden by the front panel) 12 During radio reception: Number buttons During CD playback: O REPEAT button 2 SHUF button 13 DSPL (display mode change/time set) button 14 OFF button* 15 ATT (attenuate) button The minute indication flashes 2 Press MODE repeatedly to select the band Each time you press (MODE), the band changes as follows: FMI FM - FM III - AM 3 Set the minute To go forward To go backward 3 Press SENS/BTM for two seconds The unit stores stations in the order of their frequencies on the number buttons A beep sounds when the setting is stored _ DDB 3 Press DSPL *Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press OFF) on the unit for two seconds to turn off the clock display after turning off the engine When you press OFF momentarily, the clock display does not turn off and this causes battery wear Notes • The unit does not store stations with weak signals If only a few stations can be received, some number buttons will retain their former setting • When a number is indicated in the display, the unit starts storing stations from the one currently displayed • If a CD is not in the unit, only the tuner band appears even if you press SOURCE 10:08 The clock starts Note If the car has no accessory position on the ignition key switch, the clock cannot be set unless the power is turned on Set the clock after you have turned on the radio, or started CD playback LI Other Functions CD Player "... Listening to a CD Locating a specific track - Automatic Music Sensor (AMS) During CD playback, press either side of SEEKIAMS for each track you want to skip Adjusting the sound characteristics Insert a CD Playback starts automatically Label side up You can adjust the bass, treble, balance, and fader You can store the bass and treble levels Each source can store the bass and treble level independently Boosting the bass sound - D-bass You can enjoy a clear and powerful bass sound The D-bass function boosts the low frequency and high frequency signal with a sharper curve than conventional bass boost You can hear the bass line more clearly even while the vocal volume remains the same You can emphasize and adjust the bass sound easily with the D-BASS control SEEK AMS > To locate succeeding tracks 000 To locate preceding tracks 1 Select the item you want to adjust by pressing SOUND repeatedly BAS (bass) + TRE (treble) -- BALANCE (left-right) --- FADER (front-rear) VOL (volume) Level D BASS 3 en D BASS 2 D BASS 1 Locating a specific point in a track - Manual Search During playback, press and hold either side of (SEEKAMS for about two seconds Release when you have found the desired point If a CD is already inserted, press (SOURCE repeatedly until "CD" appears to start playback O BASS 3 D BASS 2 D BASS 1 2 Adjust the selected item by pressing ♡ or OdB - - --- ---- ----- - - SEC 1 Frequency (Hz) 115 Elapsed playing time To search forward Adjust within three seconds after selecting the item (After three seconds, the buttons function reverts to volume control buttons ) AMS Oo To search backward Note To play back an 8 cm (3 in ) CD, use the optional Sony compact disc single adapter (CSA-8) Adjusting the bass curve Press D-BASS repeatedly to select the desired bass curve “D-BASS" appears in the display As the D-BASS number increases so does the effect Note If "LLLL" or "7777" appears in the display, you have reached the beginning or the end of the disc and you cannot go any further Cancel the beep sound To Press or OFF A Stop playback Eject the CD D-BASS 1 D-BASS 2 D-BASS OFF D -BASS 3 → Press © while pressing SOUND To obtain the beep sound again, press these buttons again Note The bass sound may distort at same volume If the bass sound distorts, select less effective bass curve Changing the display item Each time you press DSPL during CD playback, the item changes as follows: Elapsed playing time → Track number Clock + Playing a CD in various modes Playing tracks repeatedly - Repeat Play Press during playback "REPEAT" appears in the display Note If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated Attenuating the sound Press ATT "ATT" flashes When the current track is over, it will play again from the beginning To return to normal playback mode, press again To restore the previous volume level, press ATT again Playing tracks in random order - Shuffle Play Press 2 during playback "SHUF" appears in the display To return to normal playback mode, press again Troubleshooting guide Memorizing only the desired stations If you cannot tune in a preset station Press either side of SEEKAMS to search for the station (automatic tuning) Scanning stops when the unit receives a station Press either side of SEEKIAMS repeatedly until the desired station is received You can store up to 6 stations on each band (a total of 18 for FM I, FM II, and FM III, and 6 for AM) in the order of your choice The following checklist will help you remedy the problems you may encounter with your unit Before going through the checklist below, check the connection and operating procedures General Problem Cause/Solution No sound • Adjust the volume with ® Set the fader control to the center position for two-speaker systems The contents of the memory • The power cord or battery has been disconnected have been erased • The reset button has been pressed Store the settings again into the memory No beep sound • An optional power amplifier is connected and you are not using the built-in amplifier • The beep sound is cancelled 1 Press SOURCE repeatedly to select the tuner 2 Press MODE repeatedly to select the band Note If the automatic tuning stops too frequently, press SENS/BTM repeatedly until "LOCAL" (local seek mode) is displayed Only the stations with relatively strong signals will be tuned in 3 press and hold either side of SEEKIAMS to tune in the station that you want to store on the number button Cause/Solution CD playback Problem CD cannot be loaded Tip If you know the frequency of the station you want to listen to, press and hold either side of SEEKIAMS until the desired frequency appears (manual tuning) 4 Press and hold the desired number button (0 to 6) until "MEM" appears The number button indication appears in the display If FM stereo reception is poor - Monaural Mode • Another CD is already loaded • The CD was forcibly inserted upside down Dirty disc The ambient temperature exceeds 50°C (122°F) Press the reset button Press SENS/BTM repeatedly until "MONO" appears The sound improves, but becomes monaural ("STEREO” disappears) Play does not begin CD is automatically ejected CD will not eject The operation buttons do not function The sound skips due to vibration Note If you try to store another station on the same number button, the previously stored station will be erased • The unit is installed at an angle of more than 60° . The unit is not installed in a sturdy part of the car To return to normal mode, press again until "MONO" disappears - N Cause/Solution Receiving the memorized stations Radio reception Problem Preset tuning is not possible Changing the display item Each time you press DSPL, the item changes as follows: Frequency - Clock 1 Press SOURCE repeatedly to select the tuner 2 Press MODE repeatedly to select the band Automatic tuning is not possible The stations cannot be received The sound is hampered by noises The "STEREO" indication flashes • Memorize the correct frequency • The broadcast signal is too weak The broadcast signal is too weak Use manual tuning Connect an power aerial control lead (blue) or accessory power supply lead (red) to the power supply lead of a car's aerial booster (When your car has built-in FM/AM aerial in the rear/ side glass only) Tune in the frequency accurately • The broadcast signal is too weak + Set to the MONO mode 3 Press the number button (0 to 6) on which the desired station is stored Solution Error displays The following indications will flash for a while Display Cause A CD is dirty or inserted upside E-19 down The CD player cannot be operated because of some problem Clean or insert the CD correctly Press the reset button If the above-mentioned solutions do not help improve the situation, consult your nearest Sony dealer Additional Information INN Precautions Notes on discs If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs Maintenance Dismounting the unit 1 Press the clip inside the front cover with a thin screwdriver, and gently pry the front cover free Do not use second-hand or rental CDs that have a sticky residue on the surface (for example from peeled-off stickers or from ink, or glue leaking from under the stickers) • If your car was parked in direct sunlight resulting in a considerable rise in temperature inside the car, allow the unit to cool off before operating it • If no power is being supplied to the unit, check the connections first If everything is in order, check the fuse • If no sound comes from the speakers of a two speaker system, set the fader control to the center position • If your car is equipped with a power antenna, it will extend automatically while the unit is operating Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse If the fuse blows, check the power connection and replace the fuse If the fuse blows again after replacement, there may be an internal malfunction In such a case, consult your nearest Sony dealer There are paste residue Ink is sticky SO Do not use rental CDs with old labels that are beginning to peel off 2 Repeat step 1 on the left side The front cover is removed 3. nationalenciano Fuse (10 A) If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer Stickers that are beginning to peel away, leaving a sticky residue Do not use your CDs with labels or stickers attached Notes on handling CDs A dirty or defective disc may cause sound dropouts while playing To enjoy optimum sound, handle the disc by its edge To keep the disc clean, do not touch the surface Labels are attached Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit 3 Insert a flathead screwdriver between the bracket and mounting spring Gently pry the spring toward the unit while pulling the unit out a little Repeat on the opposite side and remove the unit Notes on moisture condensation On a rainy day or in a very damp area, moisture may condense on the lenses inside the CD player Should this occur, the unit will not operate properly In this case, remove the disc and wait for about an hour until the moisture evaporates Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean In order to prevent this, open the front panel by pressing RELEASE, then detach it and clean the connectors with a cotton swab dipped in alcohol Do not apply too much force Otherwise, the connectors may be damaged Do not stick paper or tape on the labeled surface Scanner When you play 8 cm (3 in.) CDs Use the optional Sony compact disc single adapter (CSA-8) to protect the CD player from damage Do not expose the discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car **** * Main unit irittistico Back of the front panel biopolttomoottokortt 4 mm (3/16 in ) Before playing, clean the discs with an optional cleaning cloth Wipe each disc from the center out Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog discs Notes • For safety, turn off the engine before cleaning the connectors and remove the key from the ignition switch • Never touch the connectors directly with your fingers or any metal device a t bibor RAKOxobio 72/ SONY. FM/AM Compact Disc Player Installation/Connections CDX-1300 Sony Corporation © 2000 Printed in Japan Parts list The numbers in the list are keyed to those in the instructions VOOOOOOOOOOOOO X2 X4 Caution Cautionary notice for handling the bracket Handle the bracket carefully to avoid injuring your fingers TOP Connections Caution • This unit is designed for negative ground 12 V DC operation only • Before making connections, disconnect the ground terminal of the car battery to avoid short circuits • Connect the yellow and red power input leads only after all other leads have been connected • Be sure to connect the red power input lead to the positive 12 V power terminal which is energized when the ignition key is in the accessory position • Run all ground wires to a common ground point • Connect the yellow cord to a free car circuit rated higher than the unit's fuse rating If you connect this unit in series with other stereo components, the car circuit they are connected to must be rated higher than the sum of the individual component's fuse rating If there are no car circuits rated as high as the unit's fuse rating, connect the unit directly to the battery If no car circuits are available for connecting this unit, connect the unit to a car circuit rated higher than the unit's fuse rating in such a way that if the unit blows its fuse, no other circuits will be cut off • The use of optical instruments with this product will increase eye hazard Reset button When the installation and connections are over, be sure to press the reset button with a ball-point pen etc Note When you connect the power supply cord to the unit or reset the unit, wait for about 10 seconds before you insert a disc If you insert a disc within these 10 seconds, the unit will not be reset, and you will have to press the reset button again Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press OFF on the unit for two seconds to turn off the clock display after turning off the engine When you press OFF momentarily, the clock display does not turn off and this causes battery wear Connection example AUDIO OUT REAR CDX-1300 Woocooktoestroop Rear speakers (not supplied) woningen from car antenna L + oreto ee. m - 2009 Fuse (10 A) for cowowowowww Power amplifier (not supplied) ANT REM RCA pin cord (not supplied) Blue to the power antenna control lead or power supply lead of antenna booster amplifier Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna . When your car has a built-in FMIAM antenna in the rear/side glass, see "Notes on the control leads " Max supply current 0 1A White Blue/White striped AMP REM AMP REMOTE IN Left Max supply current 0 3 A White/Black striped Front speakers (not supplied) Gray Red to the +12 V power terminal which is energized in the accessory position of the ignition key Note If there is no accessory position, connect to the +12 V power (battery) terminal which is energiazed at all times Be sure to connect the black ground lead to it first Gray/Black striped Green Yellow Left to the +12 V power terminal which is energized at all times Be sure to connect the black ground lead to it first Green/Black striped Rear speakers (not supplied) Purple Black Right to a metal point of the car First connect the black ground lead, then connect the yellow and red power input leads Purple/Black striped Notes on the control leads • The ANT REM lead (blue) supplies +12 V DC when you turn on the tuner • When your car has a built-in FM/AM antenna in the reartside glass, it is necessary to connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster For details, consult your dealer • A power antenna without relay box cannot be used with this unit Notes on speaker connection • Before connecting the speakers, turn the unit off • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities Otherwise, the speakers may be damaged • Do not connect the terminals of the speaker system to the car chassis, and do not connect the terminals of the right speaker with those of the left speaker • Do not attempt to connect the speakers in parallel • Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit Doing so may damage the active speakers Therefore, be sure to connect passive speakers to these terminals Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off Connection diagram Example 1 Example 2 Front speakers (not supplied) wwwww w0000000000000000000000w atawagogo Front speakers (not supplied) www cococos com AUDIO OUT REAR Rear speakers (not supplied) Rear speakers (not supplied) Rear speakers (not supplied) Power amplifier (not supplied) Notes • Be sure to connect the earth cord before connecting the amplifier • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated Installation Precautions Mounting angle adjustment Adjust the mounting angle to less than 60° • Do not tamper with the four holes on the upper surface of the unit They are for tuner adjustments to be made only by service technicians • Choose the installation location carefully so that the unit will not interfere driving • Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater duct • Use only the supplied mounting hardware for a safe and secure installation How to detach and attach the front panel Before installing the unit, detach the front panel A To detach Before detaching the front panel, be sure to press OFF Press RELEASE, then slide the front panel a little to the left, and pull it off towards you B To attach Attach part of the front panel to part of the unit as illustrated and push the left side into position until it clicks TA OFF RELEASE Mounting example Installation in the dashboard max size 5 x 6 mm 182 mm 2020costosow marina \\53 mm w ww! AO: WwW2070 QO w Bend these claws outward for a tight fit, if necessary Note To prevent malfunction, install only with the supplied screws © max size 5 x 6 mm With the TOP marking up To support the unit Fire wall Dashboard max size M4 x 6 mm VOOOQO With the ribs on bottom Ribs Mounting the unit in a Japanese car You may not be able to install this unit in some makes of Japanese cais In such a case, consult your Sony dealer TOYOTA NISSAN max size 5 x 6 mm max size 5 x 6 mm Su to dashboard/center console to dashboard/center console Amor...,,.W.NA mwimm mm.. / : . . WAV, ." *. YX Bracket max size Bracket max size 5 x 6 mm Din ** !.6X axoMOWWnixwwww!: 00XX 5 x 6 mm 4: 00: a . ww.oo 0.102* W . . 09, ww BE m., w .w. u wi.co.0.0:. .M ur n. www . A .YOYOX9 0CM Bracket 0x Bracket . Ww V .m OWWWWWeron .w * .V..w.w..0.. .. Wyco:00: 0 * * U . Y Existing parts supplied to your car : Existing parts supplied to your car Note To prevent malfunction, install only with the supplied screws STOP - NEED HELP?? DO YOU NEED ASSISTANCE WITH INSTALLATION OR PRODUCT APPLICATION ON YOUR SONY MOBILE PRODUCT? TREUATS n Installatio Monau, dау аn SONYO Tamo Avoillele Spm EST. Sony Mobile 4-557-152-01 (T1) F SONY Car Audio LIMITED WARRANTY Sony Electronics Inc ("Sony") warrants this Product (including any accessories) against defects in material or workmanship as follows: 1 LABOR: For a period of one (1) year from the date of purchase, if this product is determined to be defective, Sony will repair or replace the Product, at its option, at no charge, or pay the labor charges to any Sony autho rized service facility After the Warranty Period, you must pay for all labor charges 2 PARTS: In addition, Sony will supply, at no charge, new or rebuilt replacements in exchange for defective parts for a period of one (1) year After the warranty period, you must pay for all parts costs 3 ACCESSORIES: Parts and labor for all accessories are for one (1) year. To obtain warranty service, you must take the Product, or deliver the Product freight prepaid, in either its original packaging or packaging affording an equal degree of protection, to any authorized Sony service facility This warranty does not cover customer instruction, installation, set up adjustments or signal reception prob lems This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negli gence, commercial use, or modification of, or to any part of the Product, including the antenna This warranty does not cover damage due to improper operation or maintenance, connection to improper voltage supply, or attempted repair by anyone other than a facility authorized by Sony to service the Product This warranty does not cover Products sold AS IS or WITH ALL FAULTS, or consumables (such as fuses or batteries) This warranty is valid only in the United States Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service This warranty is invalid if the factory applied serial number has been altered or removed from the Product REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIB ITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU LAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you In addition, if you enter into a service contract with the Sony Partnership within 90 days of the date of sale, the limitation on how long an implied warranty lasts does not apply to you This warranty gives you specific legal rights, and you may have other rights which vary from state to state For your convenience, Sony Electronics Inc has established telephone numbers for frequently asked questions: To locate the servicer or dealer nearest you, or for service assistance or resolution of a service problem, or for product information or operation, call: Sony Direct Response Center 1-(800)-222-7669 or write to: Sony Direct Response Center 12451 Gateway Blvd Fort Myers, FL 33913 For an accessory or part not available from your authorized dealer, call: 1-(800)-488-SONY (7669) Printed in Japan


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply