SIEMENS HB30S50U (01) PDF MANUAL

SIEMENS HB30S50U (01) PDF SUMMARY:

What parts are needed for installation?

• Tape Measure
• Straight Edge or Ruler
• Phillips Head Screwdriver
• Level
• Pencil
• Wire Cutters or Wire Stripper
• Wire Nuts
• Volt Meter (0-250 VAC)
• 1” Hole Saw
• Hand or Saber Saw
• Drill and Drill Bit
• Safety Gloves and Goggles
• Cloth or cardboard (Optional – to Protect Floor)

---

What should I do before using the oven?

Remove all tape and packaging before using the oven. Destroy the packaging after unpacking the oven. Never allow children to play with packaging material.

---

Who should install the appliance and what codes must they follow?

A qualified technician should properly install and ground the appliance. They must follow the National Electrical Code ANSI/ NFPA No. 7 latest edition (or the Canadian Electric Code) and local electrical code requirements. Installation, electrical connections, and grounding must comply with all applicable codes.

---

What should I do if the provided manual is not followed?

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

---

What are some important safety instructions to remember?

• Read all instructions before using the appliance.
• Install only per installation instructions provided in the literature package for this oven.
• Ask your dealer to recommend a qualified technician and an authorized repair service.
• Know how to disconnect the power to the oven at the circuit breaker or fuse box in case of an emergency.
• Do not repair or replace any part of the appliance unless specifically recommended in the manuals. All other servicing should be done by a qualified technician. This may reduce the risk of personal injury and damage to the oven.
• Never modify or alter the construction of an oven by removing panels, wire covers, screws, or any other part of the product.
• DO NOT LIFT OVEN BY DOOR HANDLE. Remove the door for easier handling and installation. See ‘Removing the Oven Door’ in the Maintenance section of the Use and Care Manual.
• Do not use the oven for storage.
• Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally.

---

What are some general instructions for installation?

• The single oven can be installed under a counter or in a wall or cabinet. The double oven can be installed in a wall or cabinet.
• Choose a location away from strong drafts and where electrical power can be provided.
• The oven support surface must be a minimum 3/4” thick plywood platform. For single ovens, it must support 150 pounds. For double ovens, it must support 290 pounds. The platform must be solid, level and flush with the bottom of the cabinet cut out.

---

What should I do to prepare the electrical outlet?

Turn power off at service panel and lock service panel before beginning. Ovens are dual rated for use on either 120/240 VAC or 120/208 VAC.

---

Where should the junction box be located?

The junction box must be located in the indicated space in Figures 1,2 and 3. It should be easily reached through the front of the cabinet where the oven will be located.

---

What should I do to verify the wiring is adequate?

Verify that wiring to house is adequate. Contact your local utility company to verify that the present electric service to your home is adequate. In some instances, the size of the wiring to the house and service switch must be increased to handle the electrical load demanded by the oven. Verify that wiring inside house is adequate.

---

What are some instructions for preparing the oven for installation?

• Remove any remaining packaging and discard.
• Remove racks, accessories and oven door(s) and set aside. See instructions in Use and Care Manual for proper removal of oven doors.
• DO NOT lift oven by door handles!.
• Place oven in front of cabinets where it is to be installed. Rest it on a jack or other sturdy support so that it is in line with the cabinet cutout.

---

What are the electrical specifications for the ovens?

Model	Volts	Watts	Amps
HB30S	120/240	3,650	17.6
HB30S	120/208	3,550	15.8
HB30D	120/240	7,250	34.8
HB30D	120/208	7,050	31.2

---

What are the cabinet cutout dimensions?

Dimension	Single 27"	Single 30"	Double 27"	Double 30"
A Cutout Width	25 1/2” – 26”	28 1/2” – 28 3/4”	25 1/2” – 26	28 1/2” – 28 3/4”
B Cutout Depth	24”	24”	24”	24”
C Cutout Height	23 5/8”	23 5/8”	47 5/8”	47 5/8”
D Floor to Bottom of Cutout	34”	34”	N/A	N/A
E Top of Cutout to Opening Above	1” min	1” min	1” min	1” min
F Bottom of Cutout to Opening Below	1/4” min	1/4” min	1/4” min	1/4” min
G Top of Cutout to Top of Counter	4 1/2” min	4 1/2” min	N/A	N/A
H Side of Cutout to Adjacent Door or Drawer Front	1/4” min	1/4” min	N/A	N/A
I Oven Door Frame Width	26 1/2”	29 1/2”	N/A	N/A

---

What should I verify before connecting the wires?

Verify that electric to the junction box has been turned off before beginning this step.

---

What kind of wire should I use and what standards should I follow?

Use copper wire ONLY. Wire size and connections must be suitable for the rating of the appliance per the National Electrical Code requirements or the Canadian Electric Code requirements.

---

How should the flexible conduit be connected?

• The flexible conduit extending from the oven should be connected directly to the junction box.
• Do not shorten flexible conduit.
• The junction box should be located to allow as much slack as possible between the junction box and the oven.
• A UL listed conduit connector must be provided at each end of the power supply cable.

---

What are the preferred and acceptable methods for wiring the oven?

The four wire branch circuit connection is preferred, but where local codes permit, a three wire branch circuit connection is also acceptable.

---

How do I perform a four wire connection?

1. Connect green ground wire from oven to green (or bare) ground wire in junction box.
2. Connect red wire from oven to red wire in junction box.
3. Connect black wire from oven to black wire in junction box.
4. Connect white wire from oven to white (or gray) neutral wire in junction box.

---

How do I perform a three wire connection?

1. Connect red wire from oven to red wire in junction box.
2. Connect black wire from oven to black wire in junction box.
3. Connect both green ground wire and white wire from oven to white (or gray) neutral wire in junction box.

---

How can the oven be converted for use with a 208 V circuit?

1. Turn power on at the breaker.
2. Open oven door (upper oven in double ovens).
3. Press CANCEL.
4. Turn knob clockwise until 6 double beeps sound.
5. Turn knob counterclockwise until 9 double beeps sound.
6. Press START.
7. Press COOKING MODE.
8. Press START.

---

How do I install the oven into the cabinet?

1. Slide oven into cabinet cutout.
2. Push straight in until oven trim is flush with cabinet wall, being careful not to crimp flexible conduit between oven and cabinet back wall. The oven should be straight, not crooked.
3. Install screws (two or four depending on model) through tap holes in trim.

---

How do I test the oven operation?

1. Verify that all control knobs are in the OFF position.
2. Turn on power at the breaker.
3. The clock will appear in the display.
4. Check power at junction box using a volt meter.
   • For 240 V installation, the reading between the red and black wires (line to line) should be 220 to 240 volts.
   • For 208 V installation, the reading between the red and black wires (line to line) should be 190 to 208 volts.
5. Test the oven mode.
   • Press COOKING MODE.
   • Turn knob to BAKE.
   • Touch START.
   • PREHEAT appears in display.
   • When the oven has reached the set temperature (350° F), it beeps and PREHEAT no longer appears.
6. If installing a double oven, test the second oven as well.
7. If any of the tests do not result as explained, contact Siemens service: 866-44-SIEMENS. Otherwise, the installation is complete.