SHARP XP-X171Q-W (01) PDF Document

The SHARP XP-X171Q-W projector has the following main features:

• Single-chip DLP projector with high resolution and high brightness, realizing projection in the resolution 3840 × 2400 pixels (4K) with an aspect ratio of 16:10.
• A proprietary sealed structure that achieves highly dust-proof performance, making filter replacement unnecessary.
• A long-life laser diode equipped in the light module, meaning replacement, adjustment, and other maintenance should not be necessary for an extended period of time.
• A wide range of optional lenses selectable according to the place of installation (Note that no lens is mounted upon shipment from the factory and optional lenses must be purchased separately).
• 360 degree free projection with a “tilt-free” function for 360° projection vertically and a “roll-free” function for 360° projection horizontally.
• Power lens control for quick and easy adjustment of zoom, focus, and position (lens shift) using buttons on the projector or the remote control.
• A variety of input terminals such as HDMI, DisplayPort, HDBaseT, and SDI.
• Multi-screen projection using multiple projectors with an edge blending function.
• Supports wired LAN via the LAN and HDBaseT ports for control by a computer.
• Supports convenient utility software like NaViSet Administrator 2 and ProAssist.
• Crestron Connected compatibility allowing multiple network-connected devices to be managed and controlled from a computer.

The light output for the SHARP XP-X171Q-W projector is 16500 lm (100 VAC: 14000 lm).

If you wish to dispose of the SHARP XP-X171Q-W equipment or its batteries, do not use the ordinary waste bin, and do not put them into a fireplace.

Step 1. Used electrical and electronic equipment and batteries should always be collected and treated SEPARATELY in accordance with local law.

Step 2. Remove USED BATTERIES from the equipment, and take them to a battery collection facility; usually a place where new batteries are sold.

Step 3. Take USED EQUIPMENT to a local, usually municipal, collection facility, where available.

Step 4. If in doubt about disposal, contact your local authorities or dealer and ask for the correct method of disposal.

The basic flow of projecting an image involves the following steps:

Step 1: Connecting your computer / Connecting the power cord (→ page 19)

Step 2: Turning on the projector (→ page 21)

Step 3: Selecting a source (→ page 24)

Step 4: Adjusting the picture size and position (→ page 25)

Step 5: Making a presentation

Step 6: Turning off the projector (→ page 33)

Step 7: After use (→ page 33)

To connect the supplied power cord to the SHARP XP-X171Q-W projector:

Step 1. First connect the supplied power cord’s three-pin plug to the AC IN terminal of the projector.

Step 2. Then connect another plug of the supplied power cord directly in the wall outlet. Do not use any plug converter.

CAUTION:

• This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected to the earth, it may cause electric shock. Please make sure the power cord is connected to the wall outlet directly and earthed properly.
• Do not use a 2-core plug converter adapter.
• Be sure to connect the projector and the computer (signal source) to the same earth point. If the projector and the computer (signal source) will be connected to different earth points, fluctuations in the earth potential may cause fire or smoke.
• To prevent the power cord from coming loose, make sure that all the prongs of the power cord plug are fully inserted into the AC IN terminal of the projector. A loose contact of the power cord may cause a fire or electric shock.

Upon connecting the power cable, the POWER indicator of the projector will light.

WARNING: The projector produces a strong light. When turning on the power, operate from the side or rear of the projector (outside the hazard zone). Also, when turning on the power, make sure no one within the projection range is looking at the lens.

Step 1. Remove the lens cap.

Step 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control.

The POWER indicator lit in red will start to blink in green. After that, the image will be projected onto the screen.

After you turn on your projector, ensure that the computer or video source is turned on.

NOTE: A blue screen (blue background) is displayed when no signal is being input (by factory default menu settings).

To select the computer or video source using the buttons on the projector cabinet:

Pressing the INPUT button will switch to the next input source in the following sequence: HDMI1 → HDMI2 → DisplayPort1 → DisplayPort2 → HDBaseT → SDI → HDMI1 → …

To adjust the projected image’s vertical and horizontal position (“Lens shift”) on the SHARP XP-X171Q-W projector:

Using the buttons on the projector cabinet:

Step 1. Press the LENS SHIFT buttons to move the projected image.

Using the Remote Control:

Step 1. Press the SHIFT button. The [LENS CONTROL (SHIFT)] screen will be displayed.

Step 2. Press the buttons to move the projected image.

CAUTION: Perform the adjustment from behind or from the side of the projector. If adjustments are performed from the front, your eyes could be exposed to strong light and get injured. Keep hands away from the lens mounting portion while performing a lens shift. Failure to do so could result in fingers being pinched by the moving lens.

To adjust the focus around the optical axis (“Focus”) using the buttons on the SHARP XP-X171Q-W projector cabinet:

Step 1. Press the FOCUS (+) or (–) button to align focus around the optical axis.

Note that the picture shows an example when the lens shift is moved upward. Adjust the lens until the bottom edge of the projection screen is in focus.

To fine-tune the size of an image (“Zoom”) on the SHARP XP-X171Q-W projector using the Remote Control:

Step 1. Press the ZOOM or FOCUS button. The [LENS CONTROL (ZOOM/FOCUS)] screen will be displayed.

Step 2. Press the button to adjust zoom.

The position to project the image on the SHARP XP-X171Q-W projector may be adjusted by the tilt foot positioned at four corners of the cabinet bottom.

If the projected image is tilted, turn either left or right tilt foot to adjust the image so that it is level.

The tilt foot can be lengthened by a maximum of 10 mm, and can be used to tilt the projector by a maximum of 1°.

NOTE: Do not lengthen the tilt foot any more than 10 mm/0.4″ as this will make the projector unstable. Pay attention to lengthen or shorten two tilt feet at the front at the same time, and same for the rear foot, otherwise, the weight of the projector is loaded on one side and it may cause damage to it.

To turn off the SHARP XP-X171Q-W projector:

Step 1. First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The [POWER OFF / ARE YOU SURE ?] message will appear.

Step 2. Secondly, press the ENTER button or press the (POWER) or the STANDBY button again. The light source will be turned off and the power supply will be cut.

CAUTION: Parts of the projector may become temporarily heated if the projector is turned off with the POWER button or if the AC power supply is disconnected during normal projector operation. Use caution when picking up the projector.

NOTE:

• While the POWER indicator is blinking green in short cycles, the power cannot be turned off.
• Do not unplug the power cord from the projector or from the power outlet while an image is being projected. Doing so could deteriorate the projector’s AC IN terminal or the power plug’s contact. To turn off the AC power while an image is being projected, use the breaker, etc.
• Do not disconnect the AC power supply to the projector within 10 seconds of making adjustment or setting changes and closing the menu. Doing so can cause loss of adjustments and settings.

After use of the SHARP XP-X171Q-W projector:

Step 1. Unplug the power cord.

Step 2. Disconnect any other cables.

Step 3. Mount the lens cap on the lens.

Step 4. Before moving the projector, screw in the tilt foot if they have been lengthened.

Specifications for the SHARP XP-X171Q-W projector:

To install AAA alkaline batteries in the remote control for the SHARP XP-X171Q-W projector:

Step 1. Press the catch and remove the battery cover.

Step 2. Install AAA alkaline batteries. Ensure that you have the batteries’ polarity (+/-) aligned correctly.

Step 3. Slip the cover back over the batteries until it snaps into place.

NOTE: When replacing the batteries, purchase 2 of the same type of AAA alkaline batteries.

Precautions for handling the remote control for the SHARP XP-X171Q-W projector:

• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Do not short, heat, or take apart batteries.
• Do not throw batteries into fire.
• If you will not be using the remote control for a long time, remove the batteries.
• Ensure that you have the batteries’ polarity (+/-) aligned correctly.
• Do not use new and old batteries together, or use different types of batteries together.
• Dispose of used batteries according to your local regulations.
• Please note that if multiple projectors are installed nearby, other projectors may unintentionally light up when you turn on the power using the remote control.

The operating range for the wireless remote control for the SHARP XP-X171Q-W projector is within 7 m/276″ and within a 30° angle from the remote sensor on the projector cabinet.

The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

To use the remote control in wired operation for the SHARP XP-X171Q-W projector:

Step 1. Connect one end of the remote cable to the REMOTE terminal on the projector.

Step 2. Connect the other end to the remote jack on the remote control.

NOTE:

• When a remote cable is inserted into the REMOTE terminal, the remote control does not work for infrared wireless communication.
• Power will not be supplied to the remote control by the projector via the REMOTE jack. Battery is needed when the remote control is used in wired operation.

To set back the lens on the SHARP XP-X171Q-W projector to the home position, press the LENS CALIBRATION button on the projector. The lens mounted on the projector goes back to the home position (roughly to the center position).

If the SHARP XP-X171Q-W projector does not turn on or shut down properly, check the following items:

• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on.
• Check to see if the projector has temperature error. If projector inside temperature is too hot or cool, it is disabled to turn on the projector as the protection. Wait for a moment and try turn on the projector again.
• If it’s hard to think the trouble is not caused on the above mentioned conditions, unplug the power cord from the outlet. Then wait 5 minutes before plugging it in again.

If the SHARP XP-X171Q-W projector will turn off unexpectedly, check the following items:

• Ensure that the [AUTO POWER OFF] is off.

If there is no picture displayed on the screen when using the SHARP XP-X171Q-W projector, check these items:

• Check if the appropriate input is selected. If there is still no picture, press the INPUT button or one of the input buttons again.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast.
• Check that the SHUTTER CLOSE button is not pressed.
• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu.
• If the HDMI input signal cannot be displayed, try the following: Reinstall your driver for the graphics card built in your computer, or use the updated driver. For reinstalling or updating your driver, refer to the user guide accompanied with your computer or graphics card, or contact the support center for your computer manufacturer. Install the updated driver or OS on your own responsibility. The provider is not liable for any trouble and failure caused by this installation.
• The signal may not be supported depending on the HDBaseT transmission device. In addition, RS232C interface may not be supported.
• If the projector is kept in sleep mode or other similar state, the temperature of the internal components could rise even when the projector is being used within its normal operating temperate. If the power is ON when that occurs, the cooling fan will turn on and it will take a little bit of time before the image is projected. Please wait for a while.

If the picture suddenly becomes dark on the SHARP XP-X171Q-W projector:

• A hot room may trigger the projector’s protection functions, which can result in a temporary reduction in luminance (brightness). Reduce the temperature in the room.

If the image on the SHARP XP-X171Q-W projector is not square to the screen:

• Reposition the projector to improve its angle to the screen.
• Perform [GEOMETRIC CORRECTION] when the trapezoid is distorted.

If the picture is blurred on the SHARP XP-X171Q-W projector, check the following:

• Adjust the focus.
• Reposition the projector to improve its angle to the screen.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens.
• Has the lens been shifted by an amount exceeding the guaranteed range?
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on. Should this happen, let the projector stand until there is no condensation on the lens.

If the image on the SHARP XP-X171Q-W projector is scrolling vertically, horizontally or both:

• Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is supported by the projector.

If the remote control does not work for the SHARP XP-X171Q-W projector, check these items:

• Aim the remote control’s infrared transmitter towards the projector’s remote control receiver.
• Install new batteries.
• Make sure there are no obstacles between you and the projector.
• Stand within 7 m/276 inch of the projector.
• If a [CONTROL ID] has been set, check whether the ID number for the remote control matches the ID number for the projector.

If the on-screen menu is not displayed on the SHARP XP-X171Q-W projector:

• Check whether On-screen mute is active. On-screen mute can be turned off using one of the following ways: Press the OSD OPEN button while holding down the CTL button on the remote control, or Holding down the MENU button on the projector cabinet for at least 10 seconds.

When the TEMP. indicator on the SHARP XP-X171Q-W projector starts to red blink in a short cycle, the thermal protector has activated and the projector may be turned off. Take the following measures:

• Pull out the power plug from the wall inlet.
• Place the projector in a cool place if it has been placed in high ambient temperature.
• Clean the exhaust vent if dust has accumulated on it.
• Leave the projector for about one hour until the inside temperature gets lower.

WARNING: Turn off the power and wait for the cooling fan to stop, disconnect the power cord and wait for the unit to cool before mounting or removing the lens. Failure to do so can result in eye injury, electric shock, or burn injuries.

Items to prepare: hexagon screwdriver (2.5 mm)

Mounting the lens:

Step 1. Remove the dust cap from the projector by pushing the tongue at the top left outward and pulling the knob at the center of the cap.

Step 2. Remove the lens cap on the back of the lens.

NOTE: Make sure to remove the lens cap at the unit back side. If the lens unit with the lens cap remaining on is installed on the projector, it may cause of malfunction.

Step 3. Hold the lens unit aligning the labelled arrow on the unit coming top and insert the unit to the projector. Insert the lens slowly all the way in, keeping the positioning slit at the same angle.

Step 4. Turn the lens unit rightward until a click is heard. The lens is now fastened onto the projector.

Step 5. Use a hexagon screwdriver to turn the lens unit screw clockwise to tighten.

After installing or replacing the lens unit, press the LENS CALIBRATION button on the projector to carry out [LENS CALIBRATION] to calibrate the adjustment range of the lens shift.

Before removing the lens from the SHARP XP-X171Q-W projector:

1. Turn on the projector and display an image.
2. Press the LENS CALIBRATION button. The lens position will be moved to the home position.
3. Turn off the projector, and then unplug the power cord.
4. Mount the lens cap on the lens.
5. Wait until the projector cabinet is cool enough to handle.

To untighten the lens:

Step 1. Use a hexagon screwdriver to turn the lens unit screw counterclockwise until it rotates freely. The screws cannot be removed.

Step 2. While pressing the LENS release button on the projector’s front panel fully in, turn the lens counterclockwise. The lens comes off.

Step 3. After slowly pulling the lens off the projector, release the LENS release button.

After removing the lens:

• Mount the lens caps (front and back) included with the lens before storing the lens.
• If no lens is going to be mounted on the projector, mount the dust cap included with the projector.

To attach the dust cap to the projector for the SHARP XP-X171Q-W projector:

Step 1. Locate the catch on the lower end of the dust cap and place it into the opening of the projector with the point of a triangle mark (▽) facing downward (① in the figure).

Step 2. Push the upper end of the dust cap against the projector to place the catches into the slot while clutching the handle (② in the figure).