SHARP XP-X141Q-W (01) PDF Document

The SHARP XP-X141Q-W is classified as either IEC/EN 62471-5:2015 risk group 2 or risk group 3 depending on the lens unit.

When classified as RG3, this projector is for professional use and must be installed in a location where safety is assured. For this reason, be sure to consult your dealer as installation must be performed by a professional installer. Never try to install the projector by yourself. This may result in visual impairment etc.

Operators shall control access to the beam within the hazard distance or install the product at the height that will prevent exposures of spectators’ eyes within the hazard distance.

When turning on the power, operate from the side or rear of the projector (outside the hazard zone). Also, when turning on the power, make sure no one within the projection range is looking at the lens.

Step 1: Connecting your computer / Connecting the power cord (page 19)

Step 2: Turning on the projector (page 21)

Step 3: Selecting a source (page 24)

Step 4: Adjusting the picture size and position (page 25)

Step 5: Making a presentation

Step 6: Turning off the projector (page 33)

Step 7: After use (page 33)

Connect a commercially available HDMI cable between the computer’s HDMI output connector and the projector’s HDMI 1 IN or HDMI 2 IN connector.

First connect the supplied power cord’s three-pin plug to the AC IN terminal of the projector, and then connect another plug of the supplied power cord directly in the wall outlet. Do not use any plug converter.

This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected to the earth, it may cause electric shock. Please make sure the power cord is connected to the wall outlet directly and earthed properly.

Do not use a 2-core plug converter adapter.

Be sure to connect the projector and the computer (signal source) to the same earth point. If the projector and the computer (signal source) will be connected to different earth points, fluctuations in the earth potential may cause fire or smoke.

To prevent the power cord from coming loose, make sure that all the prongs of the power cord plug are fully inserted into the AC IN terminal of the projector. A loose contact of the power cord may cause a fire or electric shock.

Upon connecting the power cable, the POWER indicator of the projector will light.

Step 1. Remove the lens cap.

Step 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control.

The POWER indicator lit in red will start to blink in green. After that, the image will be projected onto the screen.

After you turn on your projector, ensure that the computer or video source is turned on.

A blue screen (blue background) is displayed when no signal is being input (by factory default menu settings).

The projector produces a strong light. When turning on the power, operate from the side or rear of the projector (outside the hazard zone). Also, when turning on the power, make sure no one within the projection range is looking at the lens.

Pressing the INPUT button will switch to the next input source in the following sequence: HDMI1 → HDMI2 → DisplayPort1 → DisplayPort2 → HDBaseT → SDI → HDMI1 → …

Press the HDMI1 or HDMI2 button on the remote control.

Use the lens shift, the adjustable tilt foot, the zoom and the focus to adjust the picture size and position.

Press the LENS SHIFT buttons to move the projected image.

Press the SHIFT button. The [LENS CONTROL (SHIFT)] screen will be displayed. Then press the buttons to move the projected image.

Perform the adjustment from behind or from the side of the projector. If adjustments are performed from the front, your eyes could be exposed to strong light and get injured.

Keep hands away from the lens mounting portion while performing a lens shift. Failure to do so could result in fingers being pinched by the moving lens.

Press the LENS CALIBRATION button. The lens mounted on the projector goes back to the home position (roughly to the center position).

Press the FOCUS (+) or (–) button to align focus around the optical axis. The picture shows an example when the lens shift is moved upward. Adjust the lens until the bottom edge of the projection screen is in focus.

Press the FOCUS or ZOOM button. The [LENS CONTROL (ZOOM/FOCUS)] screen will be displayed on. Press either or button to align focus around the optical axis.

Turn the peripheral focus ring clockwise or counterclockwise. In this case the focus near the optical axis will not be changed.

Press the ZOOM (+) or (–) button to adjust zoom.

Press the ZOOM or FOCUS button. The [LENS CONTROL (ZOOM/FOCUS)] screen will be displayed on. Press the button to adjust zoom.

The position to project image may be adjusted by the tilt foot positioned at four corners of the cabinet bottom. The tilt foot height can be adjusted by its turn.

“To adjust the height of the projected image”: The height of the projected image is adjusted by turning either front or rear tilt foot.

“If the projected image is tilted”: If the projected image is tilted, turn either left or right tilt foot to adjust the image so that it is level.

The tilt foot can be lengthened by a maximum of 10 mm.

The tilt foot can be used to tilt the projector by a maximum of 1°.

Do not lengthen the tilt foot any more than 10 mm/0.4″. Doing so will make the projector unstable.

Pay attention to lengthen or shorten two tilt foot at front at the same time. Same for the rear foot, otherwise, the weight of the projector is loaded on one side and it may cause of damage to it.

Do not use the tilt foot for any purpose other than adjusting inclination of the projector installation angle.

Handling the tilt foot improperly, such as carrying the projector by grasping the tilt foot or hooking it onto a wall using the tilt foot, could damage the projector.

First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The [POWER OFF / ARE YOU SURE ?] message will appear.

Secondly, press the ENTER button or press the (POWER) or the STANDBY button again. The light source will be turned off and the power supply will be cut.

1. Unplug the power cord.

2. Disconnect any other cables.

3. Mount the lens cap on the lens.

4. Before moving the projector, screw in the tilt foot if they have been lengthened.

The minimum clearance for the intake vent (a) is 30 cm/12″ or greater. The minimum clearance for the exhaust vent (b) is 50 cm/20″ or greater. The diagram assumes there is sufficient space above the projector.

Provide sufficient space around the projectors for air intake and exhaust. When the intake and exhaust vents are obstructed, the temperature inside the projector will rise and this may result in a malfunction.

Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on.

Check to see if the projector has temperature error. If projector inside temperature is too hot or cool, it disabled to turn on the projector as the protection. Wait for a moment and try turn on the projector again.

In case it’s hard to think the trouble is not caused on the above mentioned conditions, unplug the power cord from the outlet. Then wait 5 minutes before plugging it in again.

Ensure that the [AUTO POWER OFF] is off.

Check if the appropriate input is selected. If there is still no picture, press the INPUT button or one of the input buttons again.

Ensure your cables are connected properly.

Use menus to adjust the brightness and contrast.

Check that the SHUTTER CLOSE button is not pressed.

Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu.

If the HDMI input signal cannot be displayed, try the following:

• Reinstall your driver for the graphics card built in your computer, or use the updated driver. For reinstalling or updating your driver, refer to the user guide accompanied with your computer or graphics card, or contact the support center for your computer manufacturer.
• Install the updated driver or OS on your own responsibility. We are not liable for any trouble and failure caused by this installation.

The signal may not be supported depending on the HDBaseT transmission device. In addition, RS232C interface may not be supported.

If the projector is kept in sleep mode or other similar state, the temperature of the internal components could rise even when the projector is being used within its normal operating temperate. If the power is ON when that occurs, the cooling fan will turn on and it will take a little bit of time before the image is projected. Please wait for a while.

A hot room may trigger the projector’s protection functions, which can result in a temporary reduction in luminance (brightness). Reduce the temperature in the room.

Reposition the projector to improve its angle to the screen.

Perform [GEOMETRIC CORRECTION] when the trapezoid is distorted.

Adjust the focus.

Reposition the projector to improve its angle to the screen.

Ensure that the distance between the projector and screen is within the adjustment range of the lens.

Has the lens been shifted by an amount exceeding the guaranteed range?

Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on. Should this happen, let the projector stand until there is no condensation on the lens.

Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is supported by the projector.

Aim the remote control’s infrared transmitter towards the projector’s remote control receiver.

Install new batteries.

Make sure there are no obstacles between you and the projector.

Stand within 7 m/276 inch of the projector.

If a [CONTROL ID] has been set, check whether the ID number for the remote control matches the ID number for the projector.

Check whether On-screen mute is active.

On-screen mute can be turned off using one of the following ways:

• Press the OSD OPEN button while holding down the CTL button on the remote control.
• Holding down the MENU button on the projector cabinet for at least 10 seconds.

See the Indicator Message.

Ambient temperature is high. The projector’s protection functions will activate depending on the temperature of the operating environment. Lower the room temperature.

Ambient temperature is out of the operation temperature. Check if any obstruction stays near the exhaust vent.

Lens is not mounted properly. Mount it.

Contact your dealer or service personnel. Make sure to check and inform indicator status for asking to repair.

Pull out the power plug from the wall inlet.

Place the projector in cool place if it has been placed in high ambient temperature.

Clean the exhaust vent if dust has accumulated on.

Leave the projector for about one hour until inside temperature gets lower.

The brightness for the X141Q-B/X141Q-W model is 13500 lm.

The brightness for the X171Q-B/X171Q-W model is 16500 lm (100 VAC: 14000 lm).

The resolution is 9,216,000 pixels (3840 dots x 2400 lines).

The projector is equipped with the following terminals:

The operating temperature is 32 to 113°F (0 to 45°C) with 20 to 80% humidity (without condensation).

The storage temperature is 14 to 140°F (-10 to 60°C) with 20 to 80% humidity (without condensation).

When the network is enabled, power consumption in the standby state is 3.0 W (100-240 V AC) for the X171Q-B/X171Q-W and 3.0 W (100-240 V AC) for the X141Q-B/X141Q-W.

When the network is disabled, power consumption in the standby state is 0.5 W (100-240 V AC) for both the X171Q-B/X171Q-W and X141Q-B/X141Q-W models.

The power supply is 100-240 V AC, 50/60 Hz.

The external dimensions for the X141Q-B/X141Q-W are 19.7″ (width) x 8.5″ (height) x 23.9″ (depth) / 500 mm (width) x 216 mm (height) x 606 mm (depth) (including protruding parts).

The weight for the X141Q-B/X141Q-W model is 63.9 lbs/29.0 kg (not including lens).

Video features supported by HDMI include HDR, Deep Color, 8/10/12-bit, and Lip Sync. Audio features include LPCM up to 2 ch, sample rate 32/44.1/48 KHz, sample bit 16/20/24-bit. HDMI supports HDCP 2.2/1.4.

1. Remove the dust cap from the projector. Push the tongue at the top left outward and pull the knob at the center of the cap.

2. Remove the lens cap on the back of the lens. (Note: Make sure to remove the lens cap at the unit back side. If the lens unit with the lens cap remaining on is installed on the projector, it may cause of malfunction.)

3. Hold the lens unit aligning the labelled arrow on the unit coming top and insert the unit to the projector. Insert the lens slowly all the way in, keeping the positioning slit at the same angle.

4. Turn the lens unit rightward until click is heard. The lens is now fastened onto the projector.

5. Use a hexagon screwdriver to turn lens unit screw clockwise to tighten.

Before removing the lens:

• Turn on the projector and display an image.
• Press the LENS CALIBRATION button. The lens position will be moved to the home position.
• Turn off the projector, and then unplug the power cord.
• Mount the lens cap on the lens.
• Wait until the projector cabinet is cool enough to handle.

1. To untighten, use a hexagon screwdriver to turn the lens unit screw counterclockwise until it rotates freely. The screws cannot be removed.

2. While pressing the LENS release button on the projector’s front panel fully in, turn the lens counterclockwise. The lens comes off.

3. After slowly pulling the lens off the projector, release the LENS release button. After removing the lens, mount the lens caps (front and back) included with the lens before storing the lens. If no lens is going to be mounted on the projector, mount the dust cap included with the projector.

To attach the dust cap to the projector, locate the catch on the lower end of the dust cap and place it into the opening of the projector with the point of a triangle mark (▽) facing downward (①) in the figure below), and then push the upper end of the dust cap against the projector to place the catches into the slot while clutching the handle (② in the figure below).

Pressing the POWER STANDBY button once will display the shutdown confirmation message. Press the POWER STANDBY (or ENTER) button once more to power down the projector.

Turns power ON when in standby mode.

Automatically adjusts the projected image to the optimal condition.

Displays the on-screen menu for various settings and adjustments.

Closes the menu when the on-screen menu is displayed. Cancels the operation when the confirmation message is displayed.

Moves to the next menu when the on-screen menu is displayed. Confirms the item when the confirmation message is displayed.

Opens the focus adjustment screen. Adjust the focus (of the lens) with the buttons.

The lens shift adjustment screen will be displayed. Use the buttons to adjust the lens position.

Opens the zoom adjustment screen. Adjust zoom with the buttons.

Press the CLOSE button to turn off the light source and temporarily stop projection. Press the OPEN button to resume. Simultaneously press the CTL and CLOSE buttons to close the on-screen display (On-Screen Mute). Simultaneously press the CTL and OPEN buttons to go back.

This switches [REF. LIGHT MODE] each time it is pressed.

Displays [DISPLAY] from the on-screen menu.

Displays [INFO.] from the on-screen menu.

Projects a test pattern.

Selects the HDMI1 input.

Selects the HDMI2 input.

Selects the HDBaseT input.

Selects the DisplayPort1 input.

Selects the DisplayPort2 input.

Selects the SDI input.

Used to set the control ID when performing individual operations on multiple projectors using the remote control.

This is a multipurpose button for combined use with other buttons.

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

Do not short, heat, or take apart batteries.

Do not throw batteries into fire.

If you will not be using the remote control for a long time, remove the batteries.

Ensure that you have the batteries’ polarity (+/-) aligned correctly.

Do not use new and old batteries together, or use different types of batteries together.

Dispose of used batteries according to your local regulations.

Please note that if multiple projectors are installed nearby, other projectors may unintentionally light up when you turn on the power using the remote control.

The operating range is 7 m/276″ and within 30 degrees off the center axis horizontally and vertically from the remote sensor on the projector cabinet.

The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

Connect one end of the remote cable to the REMOTE terminal and the other end to the remote jack on the remote control.

When a remote cable is inserted into the REMOTE terminal, the remote control does not work for infrared wireless communication.

Power will not be supplied to the remote control by the projector via the REMOTE jack. Battery is needed when the remote control is used in wired operation.

Turn off the projector’s power, then unplug the power cord from the power outlet. Otherwise it may cause not only fire or electric shock but also serious damage to your eyesight or burns. Contact your dealer for repairs. Never try to repair the projector on your own. Doing so is dangerous.

Do not remove or open the projector’s cabinet. Also, do not modify the projector. There are high voltage areas in the projector. It may cause fire, electric shock, or laser light leakage, resulting in serious damage to your eyesight or burns. Have qualified service personnel perform inspection, adjustments and repairs of the interior.

Do not leave the lens cap on the lens while the projector is operating. The lens cap could get hot and be warped.

Do not place objects in front of the lens that obstruct the light while the projector is operating. The object could get hot and be broken or catch fire.

Do not use flammable gas sprays to remove dust from the lens, cabinet, etc. Doing so could lead to fire.

Usage of the product must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

Handle the power cord with care. Damaging the cord could lead to fire or electric shock.

Do not place heavy objects on the cord.

Do not place the cord under the projector.

Do not cover the cord with a rug, etc.

Do not scratch or modify the cord.

Do not bend, twist or pull the cord with excessive force.

Do not apply heat to the cord.

Should the cord be damaged (exposed core wires, broken wires, etc.), ask your dealer to replace it.

Do not touch the power plug should you hear thunder. Doing so could result in electric shock.

Do not connect or disconnect the power cord with wet hands. Doing so could result in electric shock.

This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected to the earth, it may cause electric shock. Please make sure the power cord is connected to the wall outlet directly and earthed properly. Do not use a 2-pin plug converter adapter. Be sure to connect the projector and the computer (signal source) to the same earth point. If the projector and the computer (signal source) will be connected to different earth points, fluctuations in the earth potential may cause fire or smoke.

Please use the power cord supplied with this projector. If the supplied power cord does not satisfy requirements of your country’s safety standard, and voltage and current for your region, make sure to use the power cord that conforms to and satisfies them. The power cord you use must be approved by and comply with the safety standards of your country.

The power cord included with this projector is exclusively for use with this projector. For safety, do not use it with other devices.

When disconnecting the power cord, pull the power cord out by holding onto its plug.

Unplug the power cord from the power outlet before cleaning the product or when not planning to use the product for an extended time.

When the power cord or plug is heat or damaged, unplug the power cord from the power outlet, and contact your dealer.

Periodically clean dust and other debris from the power plug. Failure to do so could result in fire or electric shock.

Before moving the product, make sure the product power is off, then unplug the power cord from the power outlet and check that all cables connecting the product to other devices are disconnected.

Do not use the power cord with a power tap. Adding an extension cord may lead to fire as a result of overheating.

If the projector is going to be suspended from a ceiling or another high place, secure the lens unit using the fall prevention wire (sold separately). If the lens unit is not secured, it may fall down if it comes lose.

When installing suspended from the ceiling, use a power outlet that is within reach so the power cord can be easily plugged and unplugged.

Do not insert or drop metal or combustible objects or other foreign materials into the projector from the vents. Doing so could lead to fire or electric shock. Be particularly careful if there are children in the home. Should a foreign object get inside the projector, first turn off the projector’s power, then unplug the power cord from the power outlet and contact your dealer.

Turn off the projector’s power, then unplug the power cord from the power outlet. Otherwise it may cause not only fire or electric shock but also serious damage to your eyesight or burns. Contact your dealer for repairs. Never try to repair the projector on your own. Doing so is dangerous.

Do not leave the lens cap on the lens while the projector is operating. The lens cap could get hot and be warped.

Do not place objects in front of the lens that obstruct the light while the projector is operating. The object could get hot and be broken or catch fire.

Do not use flammable gas sprays to remove dust from the lens, cabinet, etc. Doing so could lead to fire.

Usage of the product must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

Handle the power cord with care. Damaging the cord could lead to fire or electric shock.

Do not place heavy objects on the cord.

Do not place the cord under the projector.

Do not cover the cord with a rug, etc.

Do not scratch or modify the cord.

Do not bend, twist or pull the cord with excessive force.

Do not apply heat to the cord.

Should the cord be damaged (exposed core wires, broken wires, etc.), ask your dealer to replace it.

Do not touch the power plug should you hear thunder. Doing so could result in electric shock.

Do not connect or disconnect the power cord with wet hands. Doing so could result in electric shock.

Should water, etc. get inside the projector, first turn off the projector’s power, then unplug the power cord from the power outlet and contact your dealer.

Consult your dealer for installing the projector on the ceiling. Special skills are required for ceiling installation. DO NOT perform installation work by people other than installers. Doing so may result in the projector falling and causing injury. We are not liable for any accident or/and damage resulting from improper installation or handling, misuse, modification, or natural disasters. When installed suspended from the ceiling, etc. do not hang from the projector. The projector could drop and cause injury. When installing suspended from the ceiling, use a power outlet that is within reach so the power cord can be easily plugged and unplugged.

After the lens unit removed, have at least two people hold the handles to move the projector. Attempting to move the projector alone could result in back pain or other injuries.

When moving the projector, do not hold anywhere but the handles. Otherwise the projector could fall and cause an injury.

When carrying the projector with the lens unit removed, do not touch the mounting area of the lens with your hands. Also, do not put your hand into the recess of the connection terminal. The projector could be damaged or fall down, resulting in injuries.

Turn off the projector and disconnect the power cord before attaching or detaching the lens unit. Failure to do so could result in visual impairment or burns.

Do not attach or detach the lens unit with the projector installed in a high location. The lens unit could fall and cause damage or injury.

Do not push or climb on the product. Do not grab or hang onto the product. Do not rub or tap the product with hard objects. The product may fall, causing damage to the product or personal injury.

Do not use in places such as those described below. Doing so could lead to fire or electric shock:

• Shaky tables, inclined surfaces or other unstable places.
• Poorly ventilated spaces.
• Near a radiator, other heat sources, or in direct sunshine.
• Continual vibration areas.
• Humid, dusty, steamy, or oily areas.
• An environment where there are corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc.).
• Outdoors.
• High-temperature environment where humidity changes rapidly and condensation is likely to occur.

Do not use in places such as those described below where the projector could get wet. Doing so could lead to fire or electric shock.

• Do not use in the rain or snow, on a seashore or waterfront, etc.
• Do not use in a bathroom or shower room.
• Do not install under equipment that discharges water, such as air conditioners.

Do not place vases or potted plants on the projector.

Do not place cups, cosmetics or medicines on the projector.

Connect the projector’s HDBaseT port and LAN port to a network for which there is no risk of overvoltage being applied. Overvoltage applied to the HDBaseT or LAN port could result in electric shock.

When shifting the lens or adjusting the focus or zoom, do so from either behind or the side of the projector. If adjustments are performed from the front, your eyes could be exposed to strong light and get injured.

Keep your hands away from the lens area when performing the lens shift operation. If not, your fingers could get caught in the gap between the cabinet and the lens.

Consult with your dealer about once per year for cleaning of the inside of the projector. Dust could accumulate inside of the projector if it is not cleaned for extended periods of time, leading to fires or malfunction.

If intense light like laser beams enters from the lens, it could lead to malfunction.

Take measures to prevent external light from shining on the screen. Make sure only the light from the projector shines on the screen. The less external light on the screen, the higher the contrast and the more beautiful the images.

Images will not be clear if there is dirt, scratches, discoloration, etc. on your screen. Handle the screen with care, protecting it from volatile substances, scratches and dirt.

Concerning to all maintenance operations, refer to Installation Manual and follow all instructions properly.

When planning the layout of the projector, make sure to follow the safety measures listed in the installation Manual.

In order to avoid danger, either install the device within easy reach of a wall outlet or provide a device like a breaker to disconnect power to the projector in emergency.

Take safety measures to prevent human eyes from entering the hazard zone.

Select an appropriate lens for the installation location and secure the safety zone set for each lens.

Ensure that appropriate safety measures have been taken when operating the projector, adjusting the light, etc.

Check whether the appropriate safety zone for the installed lens has been adequately secured. Periodically check the zone and maintain a record of verifications.

Educate the manager of the projector (operator) about safety before operating the projector.

Instruct the manager of the projector (operator) to perform inspections (Including safety checks on light emitted by the projector) before powering the projector on.

Instruct the manager of the projector (operator) to be able to control the projector whenever the projector is powered on in case of an emergency.

Instruct the manager of the projector (operator) to keep the installation Manual, user’s manual and inspection records in an easy-to-reach place.

Instruct them to determine whether the projector conforms to the standards of each country and region.

Do not install or store in such places as those described below.

• Locations that amplify vibrations and impacts. If installed in places where the vibrations from power sources and the like are conveyed, or in vehicles or on vessels, etc. the projector could be affected by vibrations or shocks that may damage internal parts and lead to malfunction.
• Close to high voltage power lines and power sources. It could disrupt the unit.
• Places where strong magnetic fields are generated. Doing so could lead to malfunction.
• Outdoors and places with humid or dust.
• Places exposed to oil smoke or steam.
• Places where corrosive gases are generated. Attached substances such as oil, chemicals and moisture may cause deformation or cracks of the cabinet, corrosion of the metal parts, or malfunction.

1. To prevent the projector from falling, install it on the ceiling in a way with sufficient strength to withstand the combined weight of the projector and the ceiling mount unit for an extended period of time.

2. When installing the projector on the ceiling, be sure to do so correctly in accordance with the installation Manual for the Ceiling Mount Unit. Be sure to use the fixed metal fittings and to tighten the screws securely.

3. To prevent the projector from falling, use fall prevention wires.

• Use commercially available metal fittings to join the robust part of a building or construction and the security bar of the projector with the fall prevention wires.
• Use commercially available metal fittings and fall prevention wires that have sufficient strength to withstand the combined weight of the projector and the ceiling mount unit.
• Slightly slack off the fall prevention wires so as not to put a load on the projector.

Personally identifiable information, such as IP addresses, may be saved on the projector. Before transferring or disposing of the projector, clear this data by performing [RESET] on the on-screen menu. For items that cannot be reset, please clear them individually.

When the projector is used at high altitudes (places where the atmospheric pressure is low), it may be necessary to replace the optical parts sooner than usual.

Detach the lens unit once, and be sure to attach the lens cap so as not to scratch the lens. Also, attach a dust protective cap to the projector.

Do not subject the projector to vibrations or strong shocks. The projector could be damaged otherwise.

Do not use the tilt feet for purposes other than adjusting the projector’s tilt. Improper handling, such as carrying the projector by the tilt feet or using it leaned against a wall, could lead to malfunction.

Do not touch the surface of the projection lens with bare hands. Fingerprints or dirt on the surface of the projection lens will be enlarged and projected on the screen. Do not touch the surface of the projection lens.

Do not unplug the power cord from the projector or the power outlet while projecting. Doing so could cause deterioration of the projector’s AC IN terminal or power plug contact. To interrupt the AC power supply while images are being projected, use a breaker, etc.

The remote control will not work if the projector’s remote signal sensor or the remote control’s signal transmitter is exposed to strong light or if there are obstacles between them that obstruct the signals.

Operate the remote control from within 7 meters from the projector, pointing it at the projector’s remote signal sensor.

Do not drop the remote control or handle it improperly.

Do not let water or other liquids get on the remote control. Should the remote control get wet, wipe it off immediately.

Avoid using in hot and humid places as far as possible.

Incorrect usage of batteries can result in leaks or bursting.

• Use the specified batteries only.
• Insert batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery brands.
• Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries.
• Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment. If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your clothing may cause a skin irritation or damage your eye.
• If you will not use the remote control for a long time, remove the batteries.
• Leaving a battery in an extremely high temperature surrounding environment, or a battery subject to extremely low air pressure, that can result in an explosion or the leakage of flammable liquid or gas.
• Properly dispose of depleted batteries. Disposal of a battery into water, fire, or a hot oven, or mechanically crushing, cutting, or modifying a battery can result in an explosion.
• Do not short-circuit the batteries.
• Do not charge the batteries. The batteries provided are not rechargeable.
• Contact your dealer or local authorities when disposing of batteries.

Do not obstruct the projector’s vents. Also, do not place such soft objects as paper or cloths underneath the projector. Doing so could lead to fire. Leave sufficient space between the place where the projector is installed and its surroundings.

Do not touch the exhaust vent area while projecting or immediately after projecting images. The exhaust vent area may be hot at this time and touching it could cause burns.

The optional lens units available are: