SHARP SKMD24F0AS (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD SHARP SKMD24F0AS (01) PDF MANUAL


PDF Content Summary: 24" FLUSH MOUNT DEFLECTOR VENT: SKMD24F0AS / SKMD24F0AH INSTALLATION INSTRUCTIONS IMPORTANT NOTES TO THE INSTALLER • Read all of the Installation Manual that is included with the Microwave Drawer before installing in the flush mount configuration. • Observe all governing codes, ordinances, and safety instructions. • Be sure to leave these instructions with the consumer. Parts includes: Part SKMD24F0AS SKMD24F0AH

PREF-B019MRP0 Flush Mount Deflector Vent (Stainless steel) Qty. 1 LX-CZB055MRE0 Mounting screws (Stainless steel) Qty. 2 1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C. A B C PREF-B026MRP0 Flush Mount Deflector Vent (Dark gray) Qty. 1 LX-CZB073MRE0 Mounting screws (Black) Qty. 2 A. 6" (152.40 mm) B. Suggested electrical outlet location C. Anti-Tip block

G Note: the face of the shelf must I K sit 1 3/4" (44.45 mm) back from E D F H D. 5" (127 mm) E. 3-1/2" (88.90 mm) F. 4" (101.60 mm) G. 24-3/16" (614.35 mm) minimum 24-1/2" (622.3 mm) maximum H. 14-13/16" (376.24 mm) to bottom of

J L Figure 1 M Anti-Tip block the face of the cabinet. N shelf face O cabinet face Mounting cleat Anti-Tip block I. 1-1/16" (26.97 mm) J. 23-1/2" (596.90 mm) minimum depth K. 22-1/8" (561.97 mm) L. 1-3/4" (44.45 mm) M. 16-7/8" (428.62 mm) opening N. Floor must support 100 lb (45.4 kg) O. 1-3/4" (44.45 mm) A. 22" (558.8 mm) mounting cleat opening width B. 1/4" (6.35 mm) C. 1-1/16" (26.97 mm)

A CL Top view Figure 2A Drawer face B C Cabinet face Note: the mounting surface of the finished cleat must sit 1 1/16" (26.97 mm) back from the face of the cabinet [pushing the face of the drawer out 1/4" (6.35 mm)]. E 1 TINSEB541MRR4 No oven A Suggested electrical outlet location Anti-Tip block B C 3. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. 4. Carefully guide the drawer into the prepared opening. Avoid contact with the sides of the cutout opening and also pinching the cord between the oven and the wall. 5. Slide the drawer all the way back until the mounting flanges touch the cleats mounted in the cabinet opening. 6. Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.

Figure 2B Front view

A. 22-1/8" (561.97 mm) mounting cleat opening width B. 24-3/16" (614.35 mm) minimum 24-1/2" (622.3 mm) maximum flush opening width C. 3/4" (19.05 mm) shelf Move oven location downward for extended countertops for better viewing angle. Anti-Tip Mounting flange Figure 4

16 7/8" (428.62 mm) flush opening height block 3/4" (19.05 mm) shelf 1 3/4" (44.45 mm) 7. Secure the drawer with the 4 screws supplied.

front face of shelf Front face of cabinet Figure 2C Side view 2. Install deflector as shown in Figure 3A. Shelf detail showing the deflector vent during installation. Position deflector vent and mark holes. Pre drill using a 1/16" (1.57 mm) bit before mounting. Figure 3A Shelf detail showing the deflector vent installed. Figure 3B E 2 30" FLUSH MOUNT DEFLECTOR VENT: SKMD30F0AS INSTALLATION INSTRUCTION

IMPORTANT NOTES TO THE INSTALLER • Read all of the Installation Manual that is included with the Microwave Drawer before installing in the flush mount configuration. Parts includes: Qty. Part number PREF-B020MRP0 Flush Mount

1 • Observe all governing codes, ordinances, and safety instructions. • Be sure to leave these instructions with the consumer. Deflector Vent

1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C. A B C 2 LX-CZB055MRE0 Mounting screws A. 6" (152.40 mm) B. Suggested electrical outlet location

I G K E D F H M Note: the face of the shelf must sit 1 3/4" (44.45 mm) back from C. Anti-Tip block D. 5" (127 mm) E. 3-1/2" (88.90 mm) F. 4" (101.60 mm) G. 30-5/16" (769.92 mm) minimum 30-5/8" (777.87 mm) maximum

L J N Figure 1 Anti-Tip block the face of the cabinet. shelf face O cabinet face Mounting cleat Drawer face Cabinet H. 14-13/16" (376.24 mm) to bottom of Anti-Tip block I. 1-1/16" (26.97 mm) J. 23-1/2" (596.90 mm) minimum depth K. 28-7/16" (722.3 mm) L. 1-3/4" (44.45 mm) M. 16-7/8" (428.62 mm) opening N. Floor must support 100 lb (45.4 kg) O. 1-3/4" (44.45 mm) A. 28-1/2" (723.9 mm) mounting cleat opening width B. 1/4" (6.35 mm) C. 1-1/16" (26.97 mm)

A B C face

CL Top view Figure 2A Note: the mounting surface of the finished cleat must sit 1 1/16" (26.97 mm) back from the face of the cabinet [pushing the face of the drawer out 1/4" (6.35 mm)].

E 3

No oven A Suggested electrical outlet location Anti-Tip block B C 3. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. 4. Carefully guide the drawer into the prepared opening. Avoid contact with the sides of the cutout opening and also pinching the cord between the oven and the wall. 5. Slide the drawer all the way back until the mounting flanges touch the cleats mounted in the cabinet opening. 6. Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.

Figure 2B Front view A. 28-7/16" (722.3 mm) mounting cleat opening width B. 30-5/16" (769.92 mm) minimum 30-5/8" (777.87 mm) maximum flush opening width C. 3/4" (19.05 mm) shelf

Move oven location downward for extended countertops for better viewing angle. Anti-Tip Mounting flange Figure 4

16 7/8" (428.62 mm) flush opening height block 3/4" (19.05 mm) shelf 1 3/4" (44.45 mm) 7. Secure the drawer with the 4 screws supplied.

front face of shelf Front face of cabinet

Figure 2C Side view

2. Install deflector as shown in Figure 3A. Shelf detail showing the deflector vent during installation. Position deflector vent and mark holes. Pre drill using a 1/16" (1.57 mm) bit before mounting. Figure 3A Shelf detail showing the deflector shield installed. Figure 3B 100 Paragon Drive, Suite #100, Montvale, NJ 07645, USA • 1-800-BE-SHARP (237-4277) 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9, Canada E 4


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply