SEVERIN HV7166 (01) PDF Document

To connect the floor nozzle, align the extension tube connection end with the motorized floor nozzle port.

Push them together firmly until you hear a distinct click sound, indicating they are locked in place.

Align the connector of the extension tube with the intake nozzle of the hand-held suction unit.

Push the tube into the hand-held unit until it clicks firmly into place.

Align the desired accessory, such as the 2 in 1 tool or the crevice nozzle, with the intake nozzle of the hand-held suction unit.

Push the accessory directly into the intake nozzle until it is securely fitted.

Hold the wall bracket against the wall at the desired height and mark the drilling holes.

Drill the holes into the wall, insert the wall anchors, and secure the bracket using the provided screws.

Ensure the bracket is firmly attached and stable before hanging the device.

Align the back of the SEVERIN HV7166 hand-held unit with the hook mechanism on the wall bracket and slide it downwards to hang it.

You can store additional accessories, like the crevice tool and the 2 in 1 nozzle, by sliding them into the designated accessory storage slots at the bottom of the wall bracket.

Locate the charging port on the top rear section of the hand-held unit handle.

Connect the charging cable adapter pin into this port and plug the charger into a wall outlet.

A complete charge cycle for the battery takes approximately 3 hours.

While charging, the LED indicators on top of the device will flash or light up in sequence.

Once the charging process is complete, all battery bar segments on the LED display will remain fully lit, indicating a full charge.

Press the power button located on the handle grip once to turn on the vacuum cleaner.

By default, when you turn on the vacuum cleaner, it starts running in ECO mode to save energy and extend run time.

Press the power level selection button on top of the handle grip to cycle through the power levels.

Pressing it once increases the suction power to medium power, showing two lit bars. Pressing it a second time activates maximum suction power, showing three lit bars. Pressing it a third time returns the unit back to ECO mode.

To turn off the vacuum cleaner, press the main power button located on the handle grip.

Hold the hand-held unit directly over a trash bin.

Press the quick-release latch on the bottom front of the dust container to release the bottom flap.

The bottom flap will swing open, allowing the collected dust and dirt to fall into the bin. Tap gently if necessary, then press the flap shut until it clicks.

Twist the dust container clockwise or counter-clockwise as indicated by the unlock symbol to release it from the motor housing.

Pull the dust container straight down and away from the main body of the unit.

Remove the dust container from the main unit.

Grasp the top of the filter assembly inside the dust container and pull it straight up and out.

Yes, the mesh filter can be rinsed under running tap water.

Ensure the water temperature is below 40 degrees Celsius.

You must allow the washed filter components to dry completely in the air for at least 24 hours before putting them back into the unit.

Avoid placing the filter directly on hot radiators or exposing it to extreme heat sources to prevent damage.

Ensure the filter is completely dry.

Align the filter assembly with the center of the dust container and push it down firmly until it is fully seated.

Press the battery release button located on the inner side or underside of the battery compartment on the handle.

Slide the battery pack downwards and outwards to remove it from the hand-held unit.

Remove the exhaust filter block from the rear part of the hand-held unit.

Use a soft cleaning brush to gently sweep away dust and loose particles from the filter surfaces, then reinstall it securely.

Turn the motorized floor nozzle over to access the bottom side.

Locate the locking slider or latch on the side of the brush cover, slide it to unlock, and open the cover piece.

Grasp the brush roller and pull it outward from its housing slot.

Remove the brush roller from the floor nozzle housing.

Use scissors to carefully cut along the groove of the brush roller to sever any wrapped hair, threads, or carpet fibers.

Pull the cut threads and debris away from the bristles by hand and discard them.