SAMSUNG GALAXY RING Q50X (01) PDF Document

The SAMSUNG GALAXY RING Q50X features the following components:

• Temperature sensor

• Optical heart rate sensors

• Orientation indicator

The SAMSUNG GALAXY RING Q50X should be charged before its first use or after a long period of inactivity. To charge the battery:

1. Align the orientation indicator of the Ring with the marker on the charging case and place the Ring into the charging case. For best results, do not insert the Ring if it is wet or dirty.

2. Close the charging case and connect the USB Type-C cable as shown.

Note: While charging, the device and the charger may become hot. This is normal and does not affect the device’s lifespan or performance. If they become too hot, remove the device from the charger and wait for it to cool down.

To maintain the water and dust resistance of your SAMSUNG GALAXY RING Q50X, follow these tips:

• The Ring is water resistant based on an IP68 rating, which means submersion in up to 5 feet of fresh water for up to 30 minutes. It is not advised for beach or pool use.

• The charging case is not water resistant.

• To avoid electric shock and damage, do not charge the device while it is wet or in an area where it could get wet. Do not handle the device, charger, or cords with wet hands while charging.

• If the Ring or your hands are wet, they must be dried thoroughly before handling.

• Whenever your device gets wet, dry it thoroughly with a clean, soft cloth. Failure to rinse the device in fresh water and dry it as instructed may cause operability or cosmetic issues.

• Do not expose the device to water at high pressure.

• If the device is dropped or receives an impact, its water and dust resistant features may be affected. If you suspect damage, take it to a Samsung-authorized service center for inspection.

To check the battery charge level of the SAMSUNG GALAXY RING Q50X:

1. Place the Ring into the charging case.

2. Press the Multipurpose button on the case.

3. The indicator light will turn on for three seconds to show the current battery level.

You can also check the battery level for the case and Ring in the Galaxy Wearable app on your connected mobile device.

You can wirelessly charge your SAMSUNG GALAXY RING Q50X’s charging case using a supported Samsung mobile device. Some features are not available while sharing power.

1. From your mobile device, enable the Wireless power sharing feature.

2. With the mobile device face down, place the charging case on the back of the mobile device to charge. A notification sound or vibration will occur when charging begins.

Note: Wireless power sharing works with most Qi-Certified devices and requires a minimum of 30% battery on the sharing device. Speed and power efficiency vary. It may not work with some accessories or covers. If you have trouble connecting, remove any cover from each device.

For best results when using Wireless power sharing, please note:

• Remove any accessories or cover before using the feature.

• The location of the wireless charging coil may vary by device, so you may need to adjust the placement to make a connection.

• During charging, do not move or use either device.

• Call reception or data services may be affected, depending on your network environment.

• Charging speed or efficiency can vary depending on device condition or surrounding environment.

• Do not use headphones.

The indicator light on the charging case displays the status of the SAMSUNG GALAXY RING Q50X when it is in the case, and the status of the case itself when the Ring is not in it. The light patterns indicate the following:

To get the best fit for your SAMSUNG GALAXY RING Q50X, wear it with the orientation indicator facing your palm, on a finger where it is comfortable. The fit should be neither too tight nor too loose.

To connect your SAMSUNG GALAXY RING Q50X to a mobile device, you must first install the Galaxy Wearable app. The app is compatible with select devices using Android 11.0 or later.

1. Open the charging case to enter Bluetooth pairing mode. You can also press and hold the Multipurpose button on the case.

2. On your mobile device, a pop-up window will appear. Tap Connect on the window and follow the prompts to complete the connection.

To disconnect the SAMSUNG GALAXY RING Q50X from your mobile device:

1. From the Galaxy Wearable app, tap Menu (three horizontal lines icon).

2. Tap Disconnect by the name of your Ring.

Note: To connect the Ring to a new device, the Ring needs to be reset first. Resetting the Ring does not delete health data.

The SAMSUNG GALAXY RING Q50X supports a variety of features accessible through the Galaxy Wearable app. These features and their measurements are listed below.

The SAMSUNG GALAXY RING Q50X measures your sleep patterns automatically when worn while you sleep. After you wake up, you can view your data by opening the Galaxy Wearable app and tapping Sleep.

You can also add sleep records manually:

1. On the Sleep screen in the app, tap Enter data.

2. Enter your sleep information, and then tap Save.

You can enable advanced sleep measurements in the Galaxy Wearable app.

To enable Blood oxygen level measurement:

1. From Galaxy Wearable, tap Sleep.

2. Tap More options > Advanced measurement > Blood oxygen.

3. Tap the toggle to enable the feature.

To enable Snore detection:

1. From Galaxy Wearable, tap Sleep.

2. Tap More options > Advanced measurement > Snore detection.

3. Tap the toggle to enable the feature. By default, ‘Always’ is enabled. You can also tap ‘Once’ to detect for one night only. To record audio of snoring, tap ‘Record audio’ to enable it.

To enable Skin temperature measurement:

1. From Galaxy Wearable, tap Sleep.

2. Tap More options > Advanced measurement > Skin temperature during sleep.

3. Tap the toggle to enable the feature.

To get the best results when measuring your heart rate with the SAMSUNG GALAXY RING Q50X:

• Rest for 5 minutes before taking measurements.

• If the measurement is very different from your expected heart rate, rest for 30 minutes and then measure it again.

• During winter or in cold weather, keep yourself warm when measuring your heart rate.

• Smoking or consuming alcohol before measurements increases heart rate and may cause your heart rate to be different from normal.

• Avoid talking, yawning, or breathing deeply while taking measurements.

• If the sensor is not working, check the Ring’s orientation on your finger and make sure nothing is obstructing the sensor.

To manually record your heart rate:

1. From the Galaxy Wearable app, tap Heart rate.

2. Tap Measure to start measuring.

3. Tap Save to store the record.

To set heart rate alerts:

The Ring can alert you through the Samsung Health app if your heart rate is higher or lower than a specified resting rate for more than 10 minutes.

1. From the Galaxy Wearable app, tap Heart rate.

2. Tap More options > Advanced measurement.

3. Under Heart rate alert, you can set the following:

   • High HR: Enable an alert if your heart rate is higher than your specified value.

   • Low HR: Enable an alert if your heart rate is lower than your specified value.

You can track your menstrual cycle by measuring skin temperature while you sleep. Related information can be viewed in the Samsung Health app on your connected mobile device.

To set up cycle tracking:

1. From the Galaxy Wearable app, tap Health settings.

2. Tap Predict period with skin temp to enable it.

3. Set your period start date and end date, and then tap Next.

4. Set your cycle length, and then tap Done.

Note: This feature must also be enabled in the Samsung Health app. Predicted dates may vary, and the feature may not be available in your region.

The SAMSUNG GALAXY RING Q50X automatically recognizes when you are exercising and records information such as exercise type, duration, and calories burned. If an exercise is stopped for more than one minute, the Ring stops recording.

To check and enable the exercises supported by this feature:

1. From the Galaxy Wearable app, tap Health settings > Activities to detect.

2. Tap any exercises that you want to enable.

You can reset all settings on your SAMSUNG GALAXY RING Q50X through the app.

From the Galaxy Wearable app, tap Reset > Reset. The Ring will automatically enter Bluetooth pairing mode after the reset is complete.

Your SAMSUNG GALAXY RING Q50X’s software can be updated through the firmware over-the-air (FOTA) service via the Galaxy Wearable app.

From the Galaxy Wearable app, tap Ring software update for the following options:

• Download and install: Check for and install updates manually. You must open the charging case before starting a manual update.

• Auto update: Set to install updates automatically when the Ring is in the charging case.

If you misplace your SAMSUNG GALAXY RING Q50X, your connected mobile device can help you find it through the Samsung Find app.

From the Galaxy Wearable app, tap Find my ring to use the feature.

Note: Support for the Samsung Find app may vary depending on the software version of the connected device. Options for finding devices offline must be enabled in the Samsung Find app. It may take four minutes or longer to find your Ring.

Yes. The SAMSUNG GALAXY RING Q50X contains magnets which may interfere with medical devices such as pacemakers, implantable cardioverter defibrillators, or insulin pumps. IF YOU ARE A USER OF ANY OF THESE MEDICAL DEVICES, PLEASE CONSULT WITH YOUR PHYSICIAN.

Do not store or place your device near magnetic fields. Magnetic stripe cards, including credit cards, phone cards, passbooks, hotel keys, and boarding passes, may be damaged by the magnets in the device.