ROLAND RP101 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD ROLAND RP101 (01) PDF MANUAL


PDF Content Summary: Cover1,4 RP101_e.book 3 ページ 2007年4月4日 水曜日 午前11時50分 WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, The exclamation point within an equilateral triangle is DO NOT REMOVE COVER (OR BACK). intended to alert the user to the presence of important NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. operating and maintenance (servicing) instructions in the literature accompanying the product. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING - When using electric products, basic precautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. BLUE: BROWN: As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug. For the U.K. NEUTRAL LIVE Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS,” “USING THE UNIT SAFELY” (p. 4), and “Important Notes” (p. 7). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2007 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. RP101_e.book 4 ページ 2007年4月4日 水曜日 午前11時50分 4USING THE UNIT SAFELY Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets. Do not disassemble or modify 002a Do not disassemble or modify this device. ...................................................................................... Do not repair or replace parts 003 Never attempt to repair this device or replace parts. If repair or part replacement should become necessary, you must contact your dealer or a Roland service center. ...................................................................................... Do not use or store in the following types of locations 004 • Locations of extremely high temperature (such as in direct sunlight, near heating equipment, or on a device that generates heat) • Near moisture (such as in a bathroom, near a sink, or on a wet floor) or in locations of high humidity • Locations exposed to rain • Locations of excessive dust • Locations subject to heavy vibration ...................................................................................... Do not place in an unstable location 007 Do not place this device on an unstable stand or a tilted surface. You must place it in a stable and level location. ...................................................................................... Connect the power cord to an outlet of the correct voltage 008a You must connect the power cord to an AC outlet of the correct voltage as marked on the device. ...................................................................................... The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The ● symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power- cord plug must be unplugged from the outlet. Use only the included power cord 008e You must use only the power cord included with the device. Do not use the included power cord with any other device. ...................................................................................... Do not bend the power cord or place heavy objects on it 009 Do not bend the power cord excessively, or place heavy objects on the power cord. Doing so will damage the power cord, and may cause short circuits or faulty connections, possibly resulting in fire or electrical shock. ...................................................................................... Do not share an outlet with an unreasonable number of other devices 015 Do not connect excessive numbers of electrical devices to a single power outlet. In particular, when using a power strip, exceeding the rated capacity (watts/amps) of the power strip may cause heat to be generated, possibly melting the cable. ...................................................................................... Avoid extended use at high volume 010 This device, either by itself or used in conjunction with headphones, amps, and/or speakers, is capable of producing volume levels that can cause permanent hearing damage. If you experience impaired hearing or ringing in your ears, immediately stop using the device and consult a medical specialist. ......................................................................................

RP101_e.book 5 ページ 2007年4月4日 水曜日 午前11時50分 USING THE UNIT SAFELY Do not insert foreign objects 011 Never allow foreign objects (flammable objects, Place in a well ventilated location 101a When using this device, ensure that it is placed in coins, wires, etc.) to enter this device. This can cause short circuits or other malfunctions. ...................................................................................... Turn off the power if an abnormality or malfunction occurs 012a If any of the following should occur, immediately turn off the power, disconnect the power cord from the AC outlet, and contact your dealer or a service center to have the device serviced. • The power cord is damaged • The device produces smoke or an unusual smell • A foreign object enters the device, or liquid spills into the device • The device becomes wet (by rain, etc.) • An abnormality or malfunction occurs in the device ...................................................................................... Do not allow children to use without supervision 013 In households with children, take particular care against tampering. If children are to use this device, they must be supervised or guided by an adult. ...................................................................................... Do not drop or subject to strong impact 014 Do not drop this device or subject it to strong impact. ...................................................................................... Do not use overseas 016 If you wish to use this device overseas, please contact your dealer or a service center. ...................................................................................... Do not place containers of water on the device 026 Do not place containers of water (such as a flower vase) or drinks on the device. Nor should you place containers of insecticide, perfume, alcoholic liquids, nail polish, or spray cans on the device. Liquids that spill into the device may cause it to malfunction, and may cause short circuits or faulty operation. ...................................................................................... a well ventilated location. ...................................................................................... Grasp the plug when connecting or disconnecting the power cord 102b When connecting or disconnecting the power cord to/from an AC outlet or the device itself, you must grasp the plug, not the cord. ...................................................................................... Periodically wipe the dust off the power cord plug 103a From time to time, you should unplug the power cord from the AC outlet and use a dry cloth to wipe the dust off of it. You should also unplug the power cord from the AC outlet if you will not be using the device for an extended period of time. Dust or dirt that accumulates between the power cord plug and the AC outlet can cause a short circuit, possibly resulting in fire. ...................................................................................... Manage cables for safety 104 Ensure that the connected cables are organized and managed in a safe manner. In particular, place the cables out of reach of children. ...................................................................................... Do not stand or place heavy objects on this device 106 Do not stand on this device, or place heavy objects on it. ...................................................................................... Do not connect or disconnect the power cord with wet hands 107b Do not connect or disconnect the power cord to the device or AC outlet while holding the power cord plug with wet hands. ...................................................................................... Cautions when moving this device 108d When moving this device, please check the following cautions. Then, make sure that at least two persons work together in lifting and carrying the device, all the while making sure to keep it level. When doing so, be careful not to pinch your hands or drop the device on your feet. 1 • Check whether the screws fastening the device to its stand have become loose. If they are loose, tighten them firmly. 2 • Disconnect the power cord. 3 • Disconnect external devices. 4 • Raise the adjuster of the stand (p. 15). 5 • Close the lid. 6 • Remove the music rest. ...................................................................................... 5

RP101_e.book 6 ページ 2007年4月4日 水曜日 午前11時50分 6 USING THE UNIT SAFELY Unplug the power cord from the AC outlet before cleaning 109a Before you clean the device, turn off the power and unplug the power cord from the AC outlet (p. 12). ...................................................................................... If there is a possibility of lightning strike, disconnect the power cord from the AC outlet 110a If there is a possibility of lightning strike, immediately turn off the power and disconnect the power cord from the AC outlet. ...................................................................................... Cautions when opening/closing the lid 116 Be careful when opening/closing the lid so you do not get your fingers pinched (p. 12). Adult supervision is recommended whenever small children use the unit. ...................................................................................... Keep small items out of the reach of children 118c To prevent small items such as the following from being swallowed accidentally, keep them out of the reach of children. • Included items •Screws for assembling the stand •Wing nut for headphone hook • Removed parts •Music rest attachment screws ......................................................................................

RP101_e.book 7 ページ 2007年4月4日 水曜日 午前11時50分 Important Notes 291b In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 3 and 4–6, please read and observe the following:

Power Supply 301 • Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect a power supply noise filter between this unit and the electrical outlet. 307 • Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/ or damage to speakers or other devices. 308 • Although the LEDs are switched off when the POWER switch is switched off, this does not mean that the unit has been completely disconnected from the source of power. If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. For this reason, the outlet into which you choose to connect the power cord’s plug should be one that is within easy reach and readily accessible. Placement 351 • Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference. 352a • This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers. 352b • Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off. 354b • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Also, do not allow lighting devices that normally are used while their light source is very close to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of time. Excessive heat can deform or discolor the unit. 355b • When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated. 356 • Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time. Such objects can discolor or otherwise harmfully affect the finish. 358 • Do not allow objects to remain on top of the keyboard. This can be the cause of malfunction, such as keys ceasing to produce sound. 359 • Do not paste stickers, decals, or the like to this instrument. Peeling such matter off the instrument may damage the exterior finish. Maintenance 401b • To clean the unit, use a dry, soft cloth; or one that is slightly dampened. Try to wipe the entire surface using an equal amount of strength, moving the cloth along with the grain of the wood. Rubbing too hard in the same area can damage the finish. Addition • If water droplets should adhere to this device, immediately wipe them off using a soft dry cloth. 402 • Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. 403 • The pedals of this unit are made of brass. Brass eventually darkens as the result of the natural oxidization process. If the brass becomes tarnished, polish it using commercially available metal polisher. Repairs and Data 452 • Please be aware that all data contained in the unit’s memory may be lost when the unit is sent for repairs. Important data should always be backed up in another MIDI device (e.g., a sequencer), or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data. 7

RP101_e.book 8 ページ 2007年4月4日 水曜日 午前11時50分 8 Important Notes Additional Precautions 551 • Please be aware that the contents of memory can be irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of loosing important data, we recommend that you periodically save a backup copy of important data you have stored in the unit’s memory in another MIDI device (e.g., a sequencer). 552 • Unfortunately, it may be impossible to restore the contents of data that was stored in the unit’s memory once it has been lost. Roland Corporation assumes no liability concerning such loss of data. 553 • Use a reasonable amount of care when using the unit’s buttons, knobs, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions. 556 • When connecting / disconnecting all cables, grasp the connector itself—never pull on the cable. This way you will avoid causing shorts, or damage to the cable’s internal elements. 557 • A small amount of heat will radiate from the unit during normal operation. 558a • To avoid disturbing your neighbors, try to keep the unit’s volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night). 559b • When you need to transport the unit, pack it in shock- absorbent material. Transporting the unit without doing so can cause it to become scratched or damaged, and could lead to malfunction. 560 • Do not apply undue force to the music rest while it is in use. 562 • Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable. 565 • Before opening or closing the keyboard lid, always make sure that no pets or other small animals are located on top of the instrument (in particular, they should be kept away from the keyboard and its lid). Otherwise, due to the structural design of this instrument, small pets or other animals could end up getting trapped inside it. If such a situation is encountered, you must immediately switch off the power and disconnect the power cord from the outlet. You should then consult with the retailer from whom the instrument was purchased, or contact the nearest Roland Service Center. RP101_e.book 9 ページ 2007年4月4日 水曜日 午前11時50分 Contents USING THE UNIT SAFELY ............................. 4 Important Notes.......................................... 7 Main Features........................................... 10 Panel Descriptions..................................... 11 Control Panel ..........................................................11 Rear Panel ..............................................................11 Before You Start Playing............................ 12 Connecting the Pedal Cord.......................................12 Connecting the Power Cord ......................................12 Opening/Closing the Lid..........................................12 Setting Up the Music Rest .........................................12 Connecting Headphones ..........................................13 Using the Headphone Hook.................................13 Turning the Power On and Off ..................................14 Adjusting the Sound’s Volume ...................................14 About the Pedals .....................................................14 About the Adjuster ...................................................15 Enjoying the Internal Songs ....................... 16 Performance ............................................. 17 Performing with a Variety of Sounds ..........................17 Playing Two Sounds Together (Dual Play) ...................18 Adjusting the Volume Balance in Dual Play (Dual Balance) ...................................................19 Changing the Brightness of the Sound (Brilliance) ........20 Adding Reverberation to the Sound (Reverb) ...............21 Changing the Depth of the Reverb Effect................21 Adjusting the Keyboard Touch (Key Touch) .................22 Transposing the Key of the Keyboard (Transpose)........23 Splitting the Keyboard Into Two Sections for Four-Hand Performances (Twin Piano)........................................24 Changing the Way in Which the Sound is Heard (Twin Piano Mode) .............................................25 Using Metronome ....................................................26 Sounding the Metronome ....................................26 Changing the Beat of Metronome.........................26 Changing the Metronome Volume ........................27 Changing the Metronome Tempo .........................27 Recording Your Performance ..................... 30 Recording...............................................................30 Playing Back the Recorded Performance.....................31 Erasing Recorded Performances ................................31 Changing Various Settings ......................... 32 Tuning to Other Instruments’ Pitches (Master Tuning) .... 32 Lowering/Raising the Standard Pitch .................... 32 Setting the Standard Pitch to 440.0 Hz ................. 32 Setting the Standard Pitch to 442.0 Hz ................. 32 Changing the Temperament...................................... 33 Setting the Tonic................................................. 33 Changing the Damper Pedal’s Resonance (Damper Resonance)................................................ 34 Setting the Tuning Curve (Stretch Tuning).................... 34 Disabling Everything Except Piano Play (Panel Lock) .... 35 Using the V-LINK function ......................................... 35 Remembering the Settings Even when the Power is Turned Off (Memory Backup).................................... 36 Restoring the Original Default Settings (Factory Reset) .. 36 Connecting External Devices....................... 37 Connecting to Audio Equipment ................................ 37 Connecting MIDI Devices ......................................... 38 What’s MIDI? .................................................... 38 MIDI Send Channel Settings ................................ 38 Switching Local Control On and Off ..................... 39 Sending Recorded Performance Data to a MIDI Device (Composer Out)....................................... 40 Connecting to a Computer........................................ 40 Appendices ............................................... 41 Troubleshooting....................................................... 41 Tone List ................................................................. 42 Internal Song List ..................................................... 43 Easy Operation List.................................................. 44 MIDI Implementation Chart ....................................... 46 Main Specifications ................................................. 47 Index ........................................................ 48 9

RP101_e.book 10 ページ 2007年4月4日 水曜日 午前11時50分 10 Main Features Thank you, and congratulations on your choice of the Roland Digital Piano RP101. To ensure that you obtain the maximum enjoyment and take full advantage of the RP101’s functionality, please read this owner’s manual carefully. Piano Sounds with Rich Resonance and Wide Expressive Range • This instrument features a piano sound generator that utilizes stereo sampling, so it is capable of faithfully recreating the sound of a high-quality concert grand piano, realistically reproducing even the finest details, including the sound of the hammers striking the strings. With a maximum polyphony of 64 notes, it has ample capability even for performances that make full use of pedaling. The Playing Feel of a Grand Piano • The PHA alpha II keyboard gives you a weighty playing feel in the low register while becoming lighter in the high register, replicating the authentic feel of a piano. • The pedal position is detected smoothly, allowing you to vary the effect by the changing the depth to which you press the pedal. You can take advantage of the way in which subtle differences in pedaling will affect the sound. A Compact Cabinet that Fits Anywhere • The newly designed cabinet projects a sense of elegant craftsmanship. It can be placed nearly anywhere, and does not occupy excessive space. • In addition to a sliding keyboard lid that stores inside the instrument, there’s a headphone hook for conveniently storing your headphones when not using them. Functionality to Assist Your Practicing • With metronome and recorder functions, as well as 65 built-in songs, you can experience the kind of piano lessons that are possible only with digital pianos. RP101_e.book 11 ページ 2007年4月4日 水曜日 午前11時50分 Panel Descriptions Control Panel Rear Panel 1 Phones Jacks 2Pedal Connector 3AC Inlet 1 Phones Jacks You can connect headphones to these jacks (p. 13). 2 Pedal Connector Connect the pedal cord to this connector (p. 12). 456789 10 11 12 3 AC Inlet Connect the supplied power cord here (p. 12). Control Panel 4 [POWER] Switch Turns the power on/off (p. 14). 5 [VOLUME] Knob Adjusts the overall volume level (p. 14). 6 [TONE] Button Used to choose the tone played by the keyboard (p. 17). 7 [SONG] Button Plays the internal songs (p. 16) or the song you recorded (p. 31). If you simultaneously press the [SONG] button and [METRONOME] button, you’ll enter recording- standby mode (p. 30). 8 [METRONOME] Button These jacks can be connected to another sound generating device or an audio device, so that the sound of that device will be output from the RP101’s speakers (p. 37).

Turns the metronome on/off (p. 26). 9 [REVERB/KEY TOUCH] Button Adds reverberation to the sound (p. 21). Modifies the playing feel of the keyboard (p. 22). Rear Panel 10 MIDI Out/In Connectors Connect to external MIDI devices to exchange performance data (p. 38). 11 Input Jacks 12 Output Jacks Allows you to output the piano’s sound to sound reinforcement equipment to obtain a more powerful sound. These can also be connected to a tape recorder or other recording device to record a performance (p. 37). 11 RP101_e.book 12 ページ 2007年4月4日 水曜日 午前11時50分 12 Before You Start Playing Connecting the Pedal Cord 1. Connect the pedal cord to the Pedal connector on the bottom panel of the RP101, at the rear. fig.00-01 Connecting the Power Cord 1. Insert the included power cord into the AC inlet on the bottom panel of the RP101, at the rear. 2. Plug the power cord into a power outlet. NOTE Be sure to use the supplied power cord. fig.00-02 Opening/Closing the Lid To open the lid, use both hands to lift it lightly, and slide it away from yourself. To close the lid, pull it gently toward yourself, and lower it softly after it has been fully extended. fig.00-05 NOTE When opening and closing the lid, be careful not to let your fingers get caught. If small children will be using the RP101, adult supervision should be provided. NOTE If you need to move the piano, make sure the lid is closed first to prevent accidents. Setting Up the Music Rest 1. Insert the included music rest attachment screws into the screw holes on top of the RP101, and tighten the screws slightly (in two places). fig.00-03 2. Put the music rest between the screws and the RP101’s body. 3. While supporting the music rest with one hand, secure it in place by turning the screws. When attaching the music rest, support it firmly with one hand to make sure that you don’t drop it. Be careful, so you don’t get your fingers pinched. 4. To remove the music rest, support it with one hand while loosening the screws. After removing the music rest, don’t forget to retighten the screws. NOTE Do not apply excessive force to the installed music rest. NOTE Be sure to use the supplied screws for attaching the music rest. NOTE Before moving the RP101, be sure to remove the music rest to prevent accidents. RP101_e.book 13 ページ 2007年4月4日 水曜日 午前11時50分 Before You Start Playing Connecting Headphones The RP101 has two jacks for plugging in headphones. This allows two people to listen through headphones simultaneously, making it very useful for lessons and when performing piano pieces for four hands. Additionally, this allows you to play without having to worry about bothering others around you, even at night. 1. Plug the headphones into the Phones jack located at the bottom left of the piano. Connecting headphones will automatically mute the sound from the internal speakers. The headphone volume is adjusted by the [VOLUME] knob of the RP101 (p. 14). fig.00-04.eNOTE Use Stereo headphones. Some notes on using headphones • To prevent damage to the cord, handle the headphones only by the headset or the plug. • Connecting the headphones when the volume of connected equipment is turned up may result in damage to the headphones. Lower the volume on the RP101 before plugging in the headphones. • Listening at excessively high volume levels will not only damage the headphones, but may also cause hearing loss. Use the headphones at a moderate volume level. ■ Using the Headphone Hook Whenever you are not using the headphones, you can hang them on the headphone hook at the lower left of the RP101. Attaching the Headphone Hook Press and twist the headphone hook included with the RP101 into the hole in the bottom of the RP101 (refer to the figure below). Turn the wing nut of headphone hook to secure the headphone hook. Phones jack x 2 Wing Nut Hole Headphone Hook 13 RP101_e.book 14 ページ 2007年4月4日 水曜日 午前11時50分 14 Before You Start Playing Turning the Power On and Off NOTE Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. To turn the power on, turn the [VOLUME] knob all the way down, and then press the [POWER] switch. The power will turn on, and the indicator of the [TONE] button will light. After a few seconds, you will be able to play the keyboard to produce sound. Use the [VOLUME] knob to adjust the volume. NOTE This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. fig.00-06.e Turning the Power Off 1. To turn the power off, turn the [VOLUME] knob all the way to the left, and press the [POWER] switch. The indicators for all buttons will go out, and the power will turn off. NOTE If you need to turn off the power completely, first turn off the [POWER] switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 7). Adjusting the Sound’s Volume 1. Turn the [VOLUME] knob to adjust the overall volume. fig.00-07.e The volume decreases About the Pedals The pedals perform the following operations. You’ll use them mainly when playing piano. Damper Pedal (right pedal) While this pedal is held down, notes will be sustained for an extended time even if you release your fingers from the keyboard. On an acoustic piano, holding down the damper pedal will cause the strings for notes other than the ones you actually play to vibrate in sympathy with what you’ve played, producing a rich resonance. The RP101 simulates this sympathetic vibration (damper resonance). NOTE You can change the amount of resonance applied with the damper pedal. Refer to “Changing the Damper Pedal’s Resonance (Damper Resonance)” (p. 34). Sostenuto Pedal (center pedal) This pedal sustains only the sounds of the keys that were already played when you pressed the pedal. Soft Pedal (left pedal) This pedal is used to make the sound softer. The volume increases Soft PedalDamper Pedal Sostenuto Pedal RP101_e.book 15 ページ 2007年4月4日 水曜日 午前11時50分 Before You Start Playing About the Adjuster If you feel that the pedal is unstable (for example if you’ve moved the RP101 to a different location), you can adjust the adjuster located on the bottom of the pedals as follows. • Turn the adjuster to lower it until the adjuster is in firm contact with the floor. The pedal may be damaged if there is a gap between the adjuster and the floor. In particular, when you’ve placed the RP101 on carpet, you must turn the adjuster until it is pressing firmly against the floor. Adjuster If the adjuster is difficult to turn, have one person lift either the left or right side of the stand to make it easier for another person to turn the adjuster and make the adjustment. NOTE After adjusting the adjuster, press the pedals, and if the front board moves, turn the adjuster further so that it makes firm contact with the floor. NOTE Always readjust the adjuster after moving the piano. 15 RP101_e.book 16 ページ 2007年4月4日 水曜日 午前11時50分 16 Enjoying the Internal Songs The RP101 comes with 65 piano songs onboard. The songs are played back continuously in sequence. fig.panel1-2 1. While holding down the [SONG] button, press the key that corresponds to the song you wish to hear. The built-in songs are assigned consecutively, starting with the B 0 key. * The song you record (p. 30) is assigned to the leftmost key (A0) of the keyboard. The song will begin playing when you press the key. When the selected song has finished playing, the next song will begin playing. When the last song has finished playing, playback will begin again from the first song. However, if you’ve recorded a song, that song will play before the first built-in song begins playing. Stopping the playback 2. Press the [SONG] button, getting the button to go dark. Playback will stop. The next time you press the [SONG] button, the song you selected most recently by pressing a key will play. For more details, refer to “Internal Song List” (p. 43). 1 4 6 9 11 13 16 18 21 23 25 23 5 7 8 10121415 57 59 61 64 17 19 20 22 24 26 . . . . . . 58 60 62 63 65 The Song You Record When you play back an internal song, the reverb effect C1 C2 C3 C6 will automatically be turned on (the button’s indicator lights). You can also play back a song by simply pressing the [SONG] button. In this case, playback will begin with the song you selected most recently by pressing a key. If there is a song you’ve recorded, the [TONE] button’s indicator will blink while you hold down the [SONG] button. • You can change the tempo of the song while it plays. The procedure is the same as in “Changing the Metronome Tempo” (p. 27). • You can make the metronome (p. 26) sound while the song plays. • If you turn on the metronome and then play back a song, a count will be sounded before the song begins playing. A count will be sounded again before playback continues to the next song. If there’s no song that you’ve recorded, the first of the built-in songs will play when you press the [SONG] button and then the A0 key. RP101_e.book 17 ページ 2007年4月4日 水曜日 午前11時50分 Performance Performing with a Variety of Sounds The RP101 contains 17 different internal tones. You can also select a tone by pressing the [TONE] button and a key to which a tone is assigned. The “Grand Piano” tone is selected when the instrument is turned on. fig.panel2-1 1. Press the [TONE] button. The button’s indicator will blink. 2. Press a key to which a tone is assigned. The [TONE] button’s indicator will change from blinking to lit. Keys to which tones are assigned: A0–C 2 keys The tone you’ve selected is heard when you finger the keyboard. Tone Key Pressed Tone Grand Piano A0 B 0 Slow Strings Mellow Piano B0 Honky-tonk C1 C 1 Strings Harpsichord D1 E 1 Choir Coupled Harpsichord E1 Electric Piano1 F1 F 1 Church Organ 1 Electric Piano2 G1 A 1 Church Organ 2 Vibraphone A1 B 1 Organ Flute Piano + Strings B1 Piano + Choir C2 C 2 Rotary Organ For more details, refer to “Tone List” (p. 42). 1 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 2 You can also switch sounds by holding down the [TONE] button and pressing a key to which a sound is assigned. NOTE While you’re selecting a sound, playing the keyboard won’t produce sound. 17 RP101_e.book 18 ページ 2007年4月4日 水曜日 午前11時50分 18 Performance Playing Two Sounds Together (Dual Play) Simultaneously playing two tones when one key is pressed is called “Dual play.” fig.panel2-5 1 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 You can also switch sounds by 2 holding down the [TONE] button and simultaneously pressing two keys to which 1. Press the [TONE] button. sounds are assigned. The button’s indicator will blink. 2. Simultaneously press a white key and black key to which tones are assigned. You can also use Dual Play by The [TONE] button’s indicator will change from blinking to lit. combining tones that are assigned to two white keys or The black keys are assigned to sounds that are suitable for layering with the sounds two black keys. assigned to white keys. Tone Key Pressed Tone Grand Piano A0 B 0 Slow Strings NOTE Mellow Piano B0 The sounds assigned to the B1 Honky-tonk C1 and C2 keys are actually C 1 Strings Harpsichord D1 combinations of two sounds. The sounds assigned to these keys can’t be combined with E 1 Choir the sounds of other keys. Coupled Harpsichord E1 Electric Piano1 F1 F 1 Church Organ 1 Electric Piano2 G1 A 1 Church Organ 2 Vibraphone A1 B 1 Organ Flute Piano + Strings B1 Piano + Choir C2 C 2 Rotary Organ 3. To cancel Dual play, press the [TONE] button and then press a key to which a sound is assigned. RP101_e.book 19 ページ 2007年4月4日 水曜日 午前11時50分 Performance ■ Adjusting the Volume Balance in Dual Play (Dual Balance) You can change the volume balance between the two layered sounds in Dual play. fig.panel2-2 1. Hold down the [TONE] button and press the “C ” or “E ” keys of any octave above C 3. The volume balance changes. • Hold down the [TONE] button and press the “C ” key of any octave above C 3 to lower the volume of the Tone 2. • Holding down the [TONE] button and pressing the “E ” key of any octave above C 3 raises the volume of the Tone 2. 2. To return to the original volume balance, hold down the [TONE] button and press both the “C ” and “E ” keys of any octave above C 3 simultaneously. You can adjust the dual balance in 9 steps. While holding down the [TONE] button... When using Dual play, the tones are handled as follows according to the combination of keys you pressed. White key and black key White key and white key, or black key and black key White key: Tone 1 Left key: Tone 1 Black key: Tone 2 Right key: Tone 2 You can also adjust the dual balance by using the “C ” and “E ” keys of any octave above C 3. 19 RP101_e.book 20 ページ 2007年4月4日 水曜日 午前11時50分 20 Performance Changing the Brightness of the Sound (Brilliance) You can adjust the brightness of the sound. 1. Hold down the [TONE] button and press one of the keys from “C4” to “B4” to adjust the brightness of the sound. Key Pressed Setting Explanation C4 -3 D4 -2 Mellow sound (three levels). E4 -1 F4 0 Normal sound. G4 +1 A4 +2 Bright sound (three levels). B4 +3 You can use the Memory Backup function to store this setting in internal memory (p. 36). C4 D4 E4 F4 G4 A4 B4 A0 This is set to “0” when the RP101 is shipped from the factory.

RP101_e.book 21 ページ 2007年4月4日 水曜日 午前11時50分 Performance Adding Reverberation to the Sound (Reverb) By applying the reverb effect you can produce a pleasant reverberation, making it sound as though you were performing in a concert hall. fig.panel2-5 You can use the Memory Backup function to store this setting in internal memory (p. 36). 1. Press the [REVERB/KEY TOUCH] button. The button’s indicator will light, and a reverb effect will be applied to the sound. To cancel the reverb effect, press the [REVERB/KEY TOUCH] button, getting its indicator to go dark. ■ Changing the Depth of the Reverb Effect The amount (depth) of the reverb effect can be set to any of eight levels. 1. Hold down the [REVERB/KEY TOUCH] button and press the “C ” or “E ” key. Pressing the “C ” key as you hold down the [REVERB/KEY TOUCH] button reduces the amount of reverb effect applied. Holding down the [REVERB/KEY TOUCH] button and pressing the “E ” key increases the reverb effect. 2. To restore the reverb depth to its factory-set state, hold down the [REVERB/KEY TOUCH] button and press the “C ” and “E ” keys simultaneously. When you play back an internal song, the reverb effect will automatically be turned on (the button’s indicator lights). You can change the Depth of the Reverb Effect by pressing any “C ” or “E ” key. While holding down Press the [Reverb/Key Touch] button... This is set to “4” when the RP101 is shipped from the factory. 21

RP101_e.book 22 ページ 2007年4月4日 水曜日 午前11時50分 22 Performance Adjusting the Keyboard Touch (Key Touch) You can adjust the touch (playing feel) of the keyboard. fig.panel2-7 1. Hold down the [REVERB/KEY TOUCH] button and press either the “A0,” “B0,” “C1,” or “D1” key. The feel of the keyboard will change. Key Pressed Setting Explanation A0 Light You can use the Memory Backup function to store this setting in internal memory (p. 36). A0 B0 C1 D1 Fortissimo (ff) can be produced by playing less strongly than usual, making the keyboard feel lighter. This setting makes it easy to play, even for children. B0 Medium This allows you to play using the most natural touch. This is the closest to the touch of an acoustic piano. This is set to “Medium” when the RP101 is shipped from the factory. C1 Heavy Fortissimo (ff) cannot be produced unless you play more strongly than usual, making the keyboard feel heavier. Dynamic fingering adds even more feeling to what you play. D1 Fixed Sounds at a fixed volume, regardless of your keyboard playing strength.

RP101_e.book 23 ページ 2007年4月4日 水曜日 午前11時50分 Performance Transposing the Key of the Keyboard (Transpose) By using the “Transpose function,” you can transpose your performance without changing the notes you play. For example, even if the song is in a difficult key with numerous sharps ( ) or flats ( ), you can transpose it to a key that is easier for you to play. When accompanying a vocalist, you can easily transpose the pitch to a range that is comfortable for the singer, while still playing the notes as written (i.e., with the same fingering positions). fig.panel2-6 1 3 -6 -4 -2 0 2 4 5 -5 -3 -1

A0 C5 B5 While holding down Press two buttons... 1. Hold down the [METRONOME] and [REVERB/KEY TOUCH] buttons, and press the key for the note you want to set as the tonic. Keys for Setting the Transposition: C5–B5 This is set to “0” when the The keyboard will be transposed. instrument is turned on. The available range is -6–0–5 (semitone steps). For example, if you want the E pitch to sound when you play the C key, hold down the [METRONOME] and [REVERB/KEY TOUCH] buttons and press the E5 key. fig.trans.e If you play C E G It will sound E G# B This setting returns to the To cancel the transposition, hold down the [METRONOME] and [REVERB/KEY original value (0) when you turn TOUCH] buttons and press the “C5” key (transposition 0). off the power. 23

RP101_e.book 24 ページ 2007年4月4日 水曜日 午前11時50分 24 Performance Splitting the Keyboard Into Two Sections for Four-Hand Performances (Twin Piano) You can divide the keyboard into two separate sections, allowing two people to perform in the same registers. C1 C2 C3 C4C5 C6 C7 C8 C3 C4 C5 C6 C3 C4 C5 C6 1. While holding down the [TONE] button and press the “C8” key. C7 The keyboard is divided into two separate sections, and the pitch changes. The right pedal now functions as the damper pedal for the right keyboard section, and the left pedal functions as the damper pedal for the left keyboard section. 2. To exit the function, hold down the [TONE] button and press the “B7” key.Off On NOTE The damper resonance function B7 C8 is not operational in Twin Piano Mode. Press

RP101_e.book 25 ページ 2007年4月4日 水曜日 午前11時50分 Performance ■ Changing the Way in Which the Sound is Heard (Twin Piano Mode) You can choose one of two ways in which the sound will be produced. 1. While holding down the [TONE] button, press the A7 or B 7 key to specify how the sound is to be produced. Key Pressed Setting Explanation A7 1 You can use the Memory Backup function to store this setting in internal memory (p. 36). C7 A7Press This is set to “1” when the RP101 is shipped from the factory. NOTE If you set Twin Piano mode to “2,” reverb will no longer be applied when you turn on Twin Notes played in the keyboard’s right zone will be Piano mode. heard more loudly from the right speaker than from the left speaker. Conversely, notes played in the keyboard’s left zone will be heard more loudly from the left speaker than from the right speaker. NOTE B 7 2 For some sounds, the sound may not be split even if you set Twin Piano mode to “2.” When you change the Twin Piano mode setting, Twin Piano will automatically be turned on. Notes played in the keyboard’s right zone will be heard only from the right speaker. Notes played in the keyboard’s left zone will be heard only from the left speaker. 25

RP101_e.book 26 ページ 2007年4月4日 水曜日 午前11時50分 26 Performance Using Metronome ■ Sounding the Metronome The RP101 features a built-in metronome. fig.panel2-4 Starting the metronome 1. Press the [METRONOME] button, getting its indicator to light. The metronome will sound. The button flashes in red and green in time with the beat selected at that time. The button lights in red on the downbeats, and in green on weak beats. Stopping the metronome 2. Once again press the [METRONOME] button, getting the button to go dark. The metronome will stop. ■ Changing the Beat of Metronome 1. Hold down the [METRONOME] button and press either the “A0,” “B0,” “C1,” “D1,” or “E1” key. Key Pressed A0 B0 C1 D1 E1 Beat Weak beats only (0/4) 2/4 3/4 4/4 6/4 The beat is set to “weak beats only” when the power is turned on. When the beat is set to “weak beats only,” the [METRONOME] button only flashes in green. A0 B0 C1 D1 E1

RP101_e.book 27 ページ 2007年4月4日 水曜日 午前11時50分 Performance ■ Changing the Metronome Volume The volume of the metronome can be adjusted, with eight volume levels available. 1. Hold down the [METRONOME] button and press a white key in the “C7” to “C8” range. ■ Changing the Metronome Tempo Changing the Tempo in Single Beat Increments 1. Hold down the [METRONOME] button and press the “C ” or “E ” key. The metronome tempo changes. Hold down the [METRONOME] button and press the “C ” key to slow down the tempo; continue pressing for consecutive decreases. Hold down the [METRONOME] button and press the “E ” key to increase the tempo; continue pressing for consecutive increases. If you hold down the [METRONOME] button and simultaneously press the “C ” key and “E ” key, the tempo will return to the standard tempo ( = 108) or the original tempo of the selected song. This is set to “3” when the instrument is turned on. B7A7G7F7E7D7C7 C8 When the metronome volume is Key Pressed C7 D7 E7 F7 G7 A7 B7 C8 set to “0,” the metronome sound does not play. Volume 0 1 2 3 4 5 6 7 You can change the tempo by pressing any “C ” or “E ” key. The range available when adjusting the tempo of the metronome is: = 20--250. Slows the tempo down Speeds the tempo up Some of the built-in songs have a tempo and time signature that are based on eighth notes or half notes, such as 3/8 or 2/2. Immediately after you’ve played back one of these While holding down the [METRONOME] button... Press songs, the tempo will be based on eighth notes or half notes. 27

RP101_e.book 28 ページ 2007年4月4日 水曜日 午前11時50分 28 Performance Selecting the Preset Tempo C2 D2 E2 F2 G2 A2 B2 C3 A0 1. Hold down the [METRONOME] button and press the white keys in the “C2” to “C3” range. The metronome tempo changes. Key Pressed C2 D2 E2 F2 G2 A2 B2 C3 Tempo 60 72 84 96 108 120 138 160 Setting the Tempo Value C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 A0 Enter 1. Hold down the [METRONOME] button and press the white keys in the “C4” to “E5” range. The tempo can be adjusted in a range of =20–250. Key Pressed C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 Tempo 1 2 3 4 5 6 7 8 9 0 Enter 2. Press the “F5” key to set that tempo. Example: Setting the Tempo to = 120 While holding down the [METRONOME] button, press the “C4 (1)” key, the “D4 (2)” key, and the “E5 (0)” key, in that sequence, then press the “F5” key to set the tempo. Example: Setting the Tempo to = 86 While holding down the [METRONOME] button, press the “C5 (8)” key and the “A4 (6)” key in that sequence, then press the “F5” key to set the tempo.

RP101_e.book 29 ページ 2007年4月4日 水曜日 午前11時50分 Performance Setting the Tempo According to the Interval a Key is Pressed as you Hold Down the [METRONOME] Button (Tap Tempo) You can set the tempo according to the interval a key is pressed as you hold down the [METRONOME] button. This function is called “Tap Tempo.” This feature allows you to set the tempo you have in mind quickly and easily, without indicating the tempo numerically. Tap Tempo 1. Hold down the [METRONOME] button and press the “B 0” key at least twice. The tempo is set to the interval between presses of the key. 29 RP101_e.book 30 ページ 2007年4月4日 水曜日 午前11時50分 30 Recording Your Performance You can record your own performance. Listening to the playback of your recorded performance can be a helpful way for you to evaluate your own playing. You can also sound a count before recording starts. This is called “count-in recording,” and allows you to match the timing of the count so that your performance will begin smoothly. Recording If using count-in recording Play the keyboard Set the tempo and time signature of the metronome before you record (p. 26, p. 27). 1. Hold down the [SONG] button and press the [METRONOME] button. The [SONG] button’s indicator will light, and the [METRONOME] button’s indicator will blink orange. This is called “recording-standby mode.” If you want to use count-in recording 2. Press the [METRONOME] button. The [METRONOME] button’s indicator will change from blinking to lit. A two-measure count will sound. The [SONG] button will blink while the count-in is sounding. After the count-in, recording begins. When recording begins, the [SONG] button’s indicator will change from blinking to lit. If not using count-in recording 2. Play the keyboard to start recording. When recording begins, the [METRONOME] button’s indicator will change from blinking to lit. 3. When you’ve finished recording, press the [SONG] button or the [METRONOME] button. When you press the button, the indicators for all buttons will blink, and the recorded performance (song) will be saved in internal memory. NOTE The RP101 always saves the newly recorded song and erases the previously recorded song. If you want to keep a song you’ve recorded, you should send the recorded song data to a MIDI device or computer (p. 40). NOTE You can’t select tones or make detailed settings, such as those for key touch or master tuning, while you’re recording or while you’re in recording-standby mode. While recording or in recording-standby mode, you can press the [REVERB/KEY TOUCH] button to turn reverb on/off (p. 21). If a recorded song has been saved, the [TONE] button’s indicator will blink while you press the [SONG] button. NOTE After you’ve finished recording, don’t turn off the power until all indicators have stopped blinking. RP101_e.book 31 ページ 2007年4月4日 水曜日 午前11時50分 Recording Your Performance Playing Back the Recorded Performance Playing back the song immediately after you’ve stopped recording 1. Press the [SONG] button. The song you recorded will play back. Playing back the recorded song after you’ve played other internal songs 1. Hold down the [SONG] button and press the “A0” key. The recorded performance will play back. Erasing Recorded Performances 1. Hold down the [SONG] button and press the [TONE] button. The recorded performance is erased. Some of the built-in songs have a tempo and time signature that are based on eighth notes or half notes, such as 3/8 or 2/2. If you record your own performance immediately after A0 playing back one of these songs, the tempo of the music that’s recorded will be based on eighth notes or half notes. If a recorded song has been saved, the [TONE] button’s indicator will blink while you press the [SONG] button. 31 RP101_e.book 32 ページ 2007年4月4日 水曜日 午前11時50分 32 Changing Various Settings Tuning to Other Instruments’ Pitches (Master Tuning) In situations such as when playing ensemble with other instruments, you can tune the RP101’s standard pitch to the pitch of another instrument. The standard pitch generally refers to the pitch of the note that’s played when you finger the middle A key. This tuning of all the instruments to a standard pitch is called “tuning.” You can set the standard pitch anywhere in a range of 415.3 Hz to 466.2 Hz. This is set to “440.0 Hz” when the RP101 is shipped from the factory. You can use the Memory Backup function to store this setting in internal memory (p. 36). ■ Lowering/Raising the Standard Pitch 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, press the “C 1” note to lower the standard pitch, or the “E 1” note to raise it. Each time you press the “C 1” key, the pitch will fall by 0.1 Hz. If you continue holding the key, the pitch will continue falling. Each time you press the “E 1” key, the pitch will rise by 0.1 Hz. If you continue holding the key, the pitch will continue rising. ■ Setting the Standard Pitch to 440.0 Hz The standard pitch will be set to 440.0 Hz. This is the most commonly used setting. The A4 (Middle A) key will sound at 440.0 Hz. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, press the “C1” key on the keyboard. ■ Setting the Standard Pitch to 442.0 Hz The standard pitch will be set to 442.0 Hz. This setting is often used for concert pianos. The A4 (Middle A) key will sound at 442.0 Hz. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, press the “D1” key on the keyboard. Press C1 Lower the pitch Raise the pitch D1 You can confirm the pitch of A4 by holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons and pressing either the A0, B 0, or B0 key. A0 B0 RP101_e.book 33 ページ 2007年4月4日 水曜日 午前11時50分 Changing Various Settings Changing the Temperament You can play classical styles such as Baroque using historic temperaments (tuning methods). Today, compositions are generally created with equal temperament in mind and are played using equal temperament. However in past ages of classical music, a variety of temperaments were used. Playing a composition with its original tuning lets you enjoy the sonorities of the chords that the composer originally intended. This is set to “Equal” when the instrument is turned on. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, press the appropriate key (F3–B3) on the keyboard. You can choose from among the seven temperaments described below. Key Pressed Temperament/Qualities Pythagorean This tuning, devised by the philosopher B 3 Pythagoras, eliminates dissonance in fourths and fifths. Dissonance is produced by third- interval chords, but melodies are euphonious. Werckmeister B3 This temperament combines the Mean Tone and Pythagorean tunings. Performances are possible in all keys (first method, number three). ■ Setting the Tonic When playing with tuning other than equal temperament, you need to specify the tonic note for tuning the song to be performed (that is, the note that corresponds to C for a major key or to A for a minor key). If you choose an equal temperament, there’s no need to select a tonic note. 1. While holding down the [METRONOME] and F3 G3 A3 B3 [REVERB/KEY TOUCH] buttons, press the tonic (root) of the key (C4–B4). A0 C3 Key Pressed Temperament/Qualities C4 D4 E4 F4 G4 A4 B4 A0 F3 NOTE When performing in ensemble with other instruments, be aware that depending on the key, there may be some shifting of the pitch. Tune the RP101 to the standard pitch of the other instruments. Equal In this tuning, each octave is divided into twelve equal steps. Every interval produces about the same amount of slight dissonance. F 3 Just Major This tuning eliminates ambiguities in the fifths and thirds. It is unsuited to playing melodies and cannot be transposed, but is capable of beautiful sonorities. G3 Just Minor The Just tunings differ from major and minor keys. You can get the same effect with the minor scale as with the major scale. A 3 Kirnberger This is an improvement of the Mean Tone and Just tunings that provides a high degree of freedom of modulation. Performances are possible in all keys (third method). A3 Mean Tone This scale makes some compromises in just intonation, enabling transposition to other keys. 33 RP101_e.book 34 ページ 2007年4月4日 水曜日 午前11時50分 34 Changing Various Settings Changing the Damper Pedal’s Resonance (Damper Resonance) On an acoustic piano, depressing the damper pedal makes the notes you play resonate with other strings, adding rich reverberations and fatness to the sound. The damper pedal on the RP101 recreates this resonance (damper resonance) when depressed. You can select from eight levels of depth for the resonant sound (resonance level). You can use the Memory Backup function to store this setting in internal memory (p. 36). This is set to “4” when the RP101 is shipped from the factory. NOTE This setting is enabled only with the piano tones. You cannot set this for other tones. 1. While holding down the [REVERB/KEY TOUCH] buttons and press the appropriate key (C2–C3) on the keyboard. Larger values will produce a deeper effect. Setting the Tuning Curve (Stretch Tuning) A piano is generally tuned to a pitch with a lower bass range and a higher treble range than equal temperament. This special tuning method for pianos is called “Stretch Tuning.” NOTE This effect works only with the piano tones. Stretch Tuning is set to On when the instrument is turned on. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, the “D2” note to turn the setting On, or press the “C2” note to turn the setting Off. Key Pressed C2 D2 E2 F2 G2 A2 B2 C3 Depth of Effect Off 1 2 3 4 5 6 7 This C2 D2 A0 Press Key Pressed Setting Explanation C2 D2 E2 F2 G2 A2 B2 C3 This is the standard tuning curve. A0 C2 Off This is the right choice when using Dual play (p. 18), or when playing in ensemble with other instruments. tuning curve expands the bass D2 On and treble ends somewhat. It is suitable for performances such as piano solos. RP101_e.book 35 ページ 2007年4月4日 水曜日 午前11時50分 Changing Various Settings Disabling Everything Except Piano Play (Panel Lock) The “Panel Lock” function locks the RP101 in a state where only piano performance can be used, and all buttons will be disabled. This prevents the settings from being inadvertently modified even if children press the buttons accidentally. NOTE In the Panel Lock state, only the grand piano sound can be played. 1. Turn the volume to the minimum, and press the [POWER] switch to turn off the power. 2. Hold down the [TONE] button and press the [POWER] switch to turn on the power. Continue holding down the [TONE] button until the panel indicator lights. All buttons are disabled. Adjust the volume by using the [VOLUME] knob. When you play the keyboard, the grand piano sound will be heard. To defeat the Panel Lock function, turn the volume down to the minimum, and turn on the power once again. Using the V-LINK function Connecting the RP101 to a V-LINK compatible image device allows you to control the images with the RP101. V-LINK V-LINK ( ) is a function that allows music and images to be performed together. By using MIDI to connect two or more V-LINK compatible devices, you can easily enjoy a wide range of visual effects that are linked to the expressive elements of a music performance. How to Use the V-LINK V-LINK is set to Off when the instrument is turned on. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, the “A 7” note to turn the setting On, or press the “G7” note to turn While holding down the [TONE] button, the setting Off. press the [POWER] switch. Key Pressed Setting Explanation G7 Off The V-LINK function is switched off. A 7 On NOTE While V-LINK is switched on, no sound is produced when you press any of the twelve keys at the left end of the keyboard. All button indicators light up when the V-LINK function is on. G7Press C8 C1 D1 E1 F1 G1 A1 B1 The V-LINK function is switched on. You can control images using the twelve keys at the left end of the keyboard. 35 RP101_e.book 36 ページ 2007年4月4日 水曜日 午前11時50分 36 Changing Various Settings Remembering the Settings Even when the Power is Turned Off (Memory Backup) Normally, the settings of the various variations will revert to their default values when the power is turned off. However, you can specify that the various settings will be remembered even when the power is turned off. This function is called “Memory Backup.” Stored Settings • Brilliance (p. 20) • Reverb On/Off, Depth of the Reverb (p. 21) • Damper Resonance (p. 34) • Key Touch (p. 22) • Twin Piano Mode (p. 25) • Master Tuning (p. 32) 1. While holding down the [SONG] button and [METRONOME] button, hold down the A0 key for approximately five seconds. The indicators of all buttons will blink several times. When memory backup has been completed, the RP101 will return to its previous state. Restoring the Original Default Settings (Factory Reset) The memory backup settings can be restored to the original default condition. This operation is referred to as “Factory Reset.” 1. While holding down the [SONG] button and [METRONOME] button, hold down the C8 key for approximately five seconds. 2. When the indicators of all buttons start blinking, switch off the power, then turn it back on again. NOTE Executing this operation will not erase the recorded performance. When you want to erase the recorded performance, refer to “Erasing Recorded Performances” A0 (p. 31). Hold down for five seconds C8 Hold down for five seconds RP101_e.book 37 ページ 2007年4月4日 水曜日 午前11時50分 Connecting External Devices

Connecting to Audio Equipment You can connect audio devices to play the sound of the RP101 through the speakers of your audio system, or to record your performance on a tape recorder or other recording device. When connecting, please use an audio cable with a standard phone plug (sold separately). Connection Examples NOTE To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. NOTE Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable. Playing the sound of the RP101 through the speakers of an audio system/Recording the performance of the RP101 on a recording device fig.audio1.e ❍ Use the following procedure when turning on the power. 1. Turn on the power of the RP101. 2. Turn on the power of the connected device. 3. Adjust the volume of each device. When Recording RP101 Performances on a Recording Device 4. Start recording with the connected device. 5. Perform on the RP101. 6. When the performance ends, stop recording on the connected equipment. Playing the sound of an audio device through the speakers of the RP101 fig.audio2.e ❍ Use the following procedure when turning on the power. 1. Turn on the power of the connected device. 2. Turn on the power of the RP101. 3. Adjust the volume of each device. NOTE You cannot use the RP101 to adjust the volume of the connected sound generating device. Turning off the power 1. Set the volume of the RP101 and of the connected devices to the minimum position. 2. Turn off the power of the RP101. Output R/L (Line Out, Aux Out) RP101 Input R/L (Line In, Aux In)

3. Turn off the connected equipment. RP101 37 RP101_e.book 38 ページ 2007年4月4日 水曜日 午前11時50分 38 Connecting External Devices Connecting MIDI Devices By connecting an external MIDI device and exchanging performance data, you can control the performances on one device from the other. For instance, you can output sound from the other instrument or switch tones on the other instrument. ■ What’s MIDI? MIDI stands for Musical Instrument Digital Interface, an international standard which allows performance information to be communicated among electronic musical instruments and computers. The RP101 provides MIDI connectors, which allow performance data to be exchanged with external devices. When these connectors are used to connect the RP101 to external devices, an even wider range of possibilities becomes available. Connection Examples NOTE To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Playing the RP101 from a MIDI sequencer/Recording an RP101 performance on a MIDI sequencer fig.midi2.e MIDI Sequencer OUT MIDI IN RP101 Set Local Off if you have connected the RP101 to a MIDI sequencer. Refer to “Switching Local Control On and Off” (p. 39). Also set your MIDI sequencer to MIDI Thru mode (so that messages received at MIDI IN will be re- transmitted without change from MIDI OUT). For details, refer to the owner’s manual of your MIDI sequencer. Perform on the RP101 to play a MIDI sound module fig.midi1.e MIDI Sound Module THRU OUT MIDI IN RP101 ■ MIDI Send Channel Settings MIDI features sixteen MIDI channels, numbered 1–16. Simply connecting a cable is not enough for communication to take place. The connected devices must be set to use the same MIDI channels. Otherwise, no sound will be produced, and no sounds can be selected. The RP101 receives all channels 1–16. When the RP101 is turned on, Channel “1” is selected. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, press the appropriate key (C6–E 7) on the keyboard. The MIDI transmit channel will switch to the number that corresponds to the note you pressed. 2 4 7 9 11 14 16 1 3 5 6 8 10121315 C6 C8 RP101_e.book 39 ページ 2007年4月4日 水曜日 午前11時50分 Connecting External Devices ■ Switching Local Control On and Off When connecting a MIDI sequencer, set Local Control to “OFF.” As illustrated, information describing what has been played on the keyboard is passed to the internal sound generator over two different routes, (1) and (2). As a result, you hear overlapping or intermittent sounds. To prevent this from happening, route (1) must be severed, by setting the unit to what is known as “Local Off.” fig.localcont.e Local Control ON The keyboard and the internal sound generator are in a linked state. fig.localon.e Local Control OFF The keyboard and the internal sound generator are in an unlinked state. No sound will be produced by the keyboard when it is played. fig.localoff.e When a Roland MT series instrument is connected, it is not necessary to make the Local Off setting. MT units transmit Local Off messages when their power is switched on. If you turn on the power in the order of the RP101 → MT series, Local Off will be set automatically. Local On is set when the power is switched on. 1. While holding down the [METRONOME] and [REVERB/KEY TOUCH] buttons, the “C8” note to turn the setting On, or press the “B7” note to turn the setting Off. (1) Local OnMIDI MIDI MIDI Sound is emitted Sound Generator Local OnLocal Off Sequencer Generator Sound MIDIMemory Each note played (2) is sounded twice IN OUT OUT B7 C8 IN Thru function On Key Pressed Value B7 Off C8 On No sound produced Sound Generator 39 RP101_e.book 40 ページ 2007年4月4日 水曜日 午前11時50分 40 Connecting External Devices ■ Sending Recorded Performance Data to a MIDI Device (Composer Out) When Composer Out is active, you can send performance data recorded with the RP101 to a connected MIDI device or computer. When you turn on the power, this is set to “Off.” 1. While holding down the [METRONOME] button and [REVERB/KEY TOUCH] button, press the F7 or F 7 key to switch Composer Out on/off. If Composer Out is turned on, the song data will be sent to a connected MIDI device or computer when you play back a recorded song. Connecting to a Computer You can use a USB MIDI interface cable (sold separately) to connect the RP101 to your computer. You can connect the RP101 to a computer that has other sequencer software installed, and then play performances from the software through the RP101. Connection Examples NOTE To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. NOTE In order to make connections to your computer, you must install “MIDI driver” software on your computer. For details, refer to the owner’s manual for your MIDI interface. F7 Use a USB MIDI interface cable to connect the USB C8 connector of your computer to the MIDI connectors of the RP101. fig.comp.e Key Pressed Value F7 Off F 7 OnUSB MIDI interface cable Computer MIDI OUT MIDI IN USB Connector of your ComputerRP101 RP101_e.book 41 ページ 2007年4月4日 水曜日 午前11時50分 Appendices Troubleshooting If you think there’s a problem, read this first. Case Cause/Remedy The power doesn’t come on Is the power cord connected and plugged in correctly? (p. 12) The button doesn’t work Is the panel locked? (p. 35) Turn the power off, then back on. No sound is heard Is the volume level of the RP101 turned all the way down? (p. 14) Are headphones plugged in? (p. 13) Has a plug remained connected to the Phones jack? Plugging headphones or other plugs into the headphone jack stops sounds from playing through the speakers. Is Local Off selected? When Local Control is set to Off, no sound is produced by playing the keyboard. Set Local Control to “On” (p. 39). Is V-LINK switched on? While V-LINK is switched on, no sound is produced when you press any of the twelve keys at the left end of the keyboard (p. 35). No sound is heard (when a MIDI instrument is connected) Have all devices been switched on? Are the MIDI cables connected correctly? Does the MIDI channel match the connected instrument? (p. 38) Sounds are heard twice (doubled) when the keyboard is played Is the RP101 in Dual play? (p. 18) When the RP101 is connected to an external sequencer, set it to the Local OFF mode (p. 39). Alternatively, the sequencer could be set so its MIDI Thru feature is OFF. Tone doesn’t change Is the panel locked? (p. 35) Turn the power off, then back on. Not all played notes are sounded The maximum number of notes that the RP101 can play simultaneously is 64. Frequent use of the damper pedal when playing along with a song may result in performance data with too many notes, causing some notes to drop out. The tuning or pitch of the keyboard or song is off Have you set Transpose? (p. 23) Are the settings for the “Temperament” (p. 33) and “Stretch Tuning” (p. 34) correct? Is the setting for the “Master Tuning” correct? (p. 32) Depressing a pedal has no effect, or the pedal effect doesn’t stop Is the pedal connected correctly? Make sure the pedal cord is securely connected to the pedal jack on the bottom of the unit, at the rear (p. 12). The pedal rattles Adjust the adjuster underneath the pedal so that the adjuster presses firmly against the floor surface (p. 15). On an acoustic piano, notes in the upper one and a half octaves of the keyboard continue In the upper range, the sound changes abruptly beyond a certain key to sound until they decay naturally, regardless of the damper pedal. There is a difference in the timbre as well. Roland pianos faithfully simulate such characteristics of the acoustic piano. On the RP101, the range that is unaffected by the damper pedal will change depending on the Transpose setting. A High-pitched whine is produced When listening through headphones: Some of the more flamboyant and effervescent piano tones feature an ample high-end component, which may make the sound appear to have metallic reverberation added. Since this reverberation becomes particularly audible when supplemented by heavy reverb, you may be able to diminish the problem by reducing the amount of reverb applied to the sound. When listening through speakers: Here, a different cause (such as resonance produced by the RP101) would be suspect. Consult your Roland dealer or nearest Roland Service Center. The bass range sounds odd, or there is a vibrating resonance When listening through speakers: Playing at loud volumes may cause instruments near the RP101 to resonate. Resonation can also occur with fluorescent light tubes, glass doors, and other objects. In particular, this problem occurs more easily when the bass component is increased, and when the sound is played at higher volumes. Use the following measures to suppress such resonance. • Place speakers so they are 10–15 cm from walls and other surfaces. • Reduce the volume. • Move the speakers away from any resonating objects. When listening through headphones: Here, a different cause would be suspect. Consult your Roland dealer or nearest Roland Service Center. The volume level of the instrument connected to Input jacks is too low Could you be using a connection cable that contains a resistor? Use a connection cable that does not contain a resistor. Case Cause/Remedy 41 RP101_e.book 42 ページ 2007年4月4日 水曜日 午前11時50分 42 Tone List [TONE] button’s Tone: While holding down the [TONE] button, press the corresponding key. A0 B0 C1D1 E1 F1 G1 A1 B1 C2 C1 C2 C3 C4 C5 C6 C7 C8 [TONE] button’s tone (p. 16, 17) Tone Key Pressed Tone Grand Piano A0 B 0 Slow Strings Mellow Piano B0 Honky-tonk C1 C 1 Strings Harpsichord D1 E 1 Choir Coupled Harpsichord E1 Electric Piano1 F1 F 1 Church Organ 1 Electric Piano2 G1 A 1 Church Organ 2 Vibraphone A1 B 1 Organ Flute Piano + Strings B1 Piano + Choir C2 C 2 Rotary Organ RP101_e.book 43 ページ 2007年4月4日 水曜日 午前11時50分 Internal Song List Song No. Key Song Name Song No. Key Song Name 1 B 0 La Fille aux Cheveux de Lin 2 B0 La Campanella 3 C1 Hungarian Rag 4 C 1 Scherzo No.2 5 D1 Sonate No.15 6 E 1 Liebesträume 3 7 E1 Étude, op.10-3 8 F1 Je te veux 9 F 1 Valse, op.64-1 10 G1 Golliwog’s Cakewalk 11 A 1 Fantaisie-Impromptu 12 A1 Arabesque 1 13 B 1 An der schönen, blauen Donau 14 B1 Auf Flügeln des Gesanges 15 C2 Mazurka No.5 16 C 2 Gymnopédie 1 17 D2 Étude, op.25-1 18 E 2 Clair de Lune 19 E2 Étude, op.10-5 20 F2 Dr. Gradus ad Parnassum 21 F 2 Grande Valse Brillante 22 G2 La prière d'une Vierge 23 A 2 Course en Troïka 24 A2 To The Spring 25 B 2 Valse, op.64-2 26 B2 Radetzky Marsch 27 C3 Träumerei 28 C 3 Moments Musicaux 3 29 D3 Prélude, op.28-15 30 E 3 Harmonious Blacksmith 31 E3 Ungarische Tänze 5 32 F3 Türkischer Marsch (Beethoven) * All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a 33 F 3 Nocturne No.2 violation of applicable laws. 34 G3 Frühlingslied 35 A 3 Präludium 36 A3 Jägerlied 37 B 3 Menuet Antique 38 B3 Für Elise 39 C4 Türkischer Marsch (Mozart) 40 C 4 Ständchen 41 D4 Humoreske 42 E 4 Blumenlied 43 E4 Alpenglöckchen 44 F4 Menuett G dur (Beethoven) 45 F 4 Venezianisches Gondellied 46 G4 Alpenabendröte 47 A 4 Farewell to the Piano 48 A4 Brautchor 49 B 4 Battle of Waterloo 50 B4 Wiener Marsch 51 C5 Le Coucou 52 C 5 Menuett G dur (Bach) 53 D5 Spinnerlied 54 E 5 Gavotte 55 E5 Heidenröslein 56 F5 Zigeuner Tanz 57 F 5 La Cinquantaine 58 G5 Csikos Post 59 A 5 Dolly's Dreaming Awakening 60 A5 La Violette 61 B 5 Fröhlicher Landmann 62 B5 Sonatine op.36-1 (Clementi) 63 C6 Sonatine op.20-1 (Kuhlau) 64 C 6 Sonatine No.5 (Beethoven) 65 D6 Fly Flee 43 RP101_e.book 44 ページ 2007年4月4日 水曜日 午前11時50分 44 Easy Operation List ■ Tone Settings While holding down the [TONE] button, press the corresponding key. A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 C4 D4 E4 F4 G4 A4 B4 A7 B7 C8 C2 C3 C4 C5 C6 C7 C8 [TONE] button’s Brilliance tone (p. 16, 17) (p. 20) Twin Piano Mode (p. 25) Twin Piano On/Off (p. 24) ■ Metronome Settings While holding down the [METRONOME] button, press the corresponding key. Tap Tempo (p. 29) A0 B0 C1D1 E1 C2 D2 E2 F2 G2 A2 B2 C3 C4 D4 E4 F4 G4 A4 B4 C5 D5 F5E5 C7 D7 F7E7 G7 A7 B7 C8 C1 C2 C3 C4 C5 C6 C7 C8 Beat (p. 26)Metronome Tempo (Reference Tempo) (p. 28) Metronome Tempo (Tempo Value) Metronome Volume (p. 28) (p. 27) RP101_e.book 45 ページ 2007年4月4日 水曜日 午前11時50分 Easy Operation List ■ Key Touch/Damper Resonance Settings While holding down the [REVERB/KEY TOUCH] button, press the corresponding key. A0 B0 C1D1 C2 D2 E2 F2 G2 A2 B2 C3 C1 C2 C3 C4 C5 C6 C7 C8 Key Touch Damper Resonance (p. 22)(p. 34) ■ Other Settings While holding down the [METRONOME] and [REVERB/KEY TOUCH] button, press the corresponding key. A0 B0 C1D1 C2 D2 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 F5E5 B5A5G5 C6 D6 F6E6 A6G6 B6 C7 D7 F7 G7 B7 C8 C1 C2 C3 C4 C5 C6 C7 C8 Master Tuning Streach Tuning Temperament/ Transpose Setting (p. 32) (p. 34) Tonic Note (p. 33) (p. 23) Composer Out (p. 40) the MIDI Channel (p. 38) Local On/Off (p. 39) V-LINK (p. 35) 45 RP101_e.book 46 ページ 2007年4月4日 水曜日 午前11時50分 MIDI Implementation ChartDIGITAL PIANO Date : Jan. 1, 2007 Model RP101 MIDI Implementation Chart Version : 1.00 Function... Basic Channel Mode ************** Note Number : ************** Velocity After Touch Pitch Bend Control Change Prog Change System Exclusive System Common System Real Time Aux Message Notes Mode 1 : OMNI ON, POLY Mode 3 : OMNI OFF, POLY Transmitted Recognized Remarks Default Changed Default Messages Altered True Voice Note ON Note OFF Key’s Ch’s 6, 3871164666791 100, 101 : True Number : Song Pos : Song Sel : Tune : Clock : Commands : : All Reset sound all controllers off : Local Control : : All Active Notes Sense OFF : Reset 111–16 1–16 Mode 3 Mode 3 xx15–113 0–127 15–113 O Ox 8n v=64 xxxx xxxOxOOData entry Volume xOOOExpression Hold 1 OOOOSostenuto Soft OOEffect 1 (Reverb) O O RPN LSB, MSB 0–119 O************** 0–119 OOxxxxxxxxxxxxxxOx xO OO Ox (123–127) Mode 2 : OMNI ON, MONO O : Yes Mode 4 : OMNI OFF, MONO X : No 46 RP101_e.book 47 ページ 2007年4月4日 水曜日 午前11時50分 Main Specifications Keyboard Keyboard 88 keys, PHA alpha II keyboard Touch Sensitivity Light, Medium, Heavy, Fixed Keyboard Modes Whole, Dual (volume balance adjustable), Twin piano Sound Generator Max. Polyphony 64 voices Tones 17 tones Temperament 7 types, selectable tonic Stretched Tuning On/Off Master Tuning 415.3–466.2 Hz (adjustable in increments of 0.1 Hz) Transpose -6–+5 (in semitones) Effects Reverb (8 levels), Damper Resonance (only for piano tones, 7 levels, Off) Recorder Track 1 track Number of songs stored 1 song Number of notes stored Approx. 5000 notes Controls Song Select, All Song Play/Stop, Rec Tempo Quarter note = 20 to 250 Resolution 120 ticks per quarter note Metronome Beat 0/4, 2/4, 3/4, 4/4, 6/4 Volume 8 levels Others Preset Songs 65 songs Rated Power Output 25 W x 2 Speakers 12 cm x 2 Control Volume Pedals Damper (half-pedal recognition), Soft (half-pedal recognition), Sostenuto Other Functions Panel Lock, V-LINK Connectors AC inlet, Pedal connector, Input jacks (L/Mono, R), Output jacks (L/Mono, R), MIDI connectors (In, Out), Phones jack (Stereo) x 2 Power Supply AC 115 V, AC 117 V, AC 220 V, AC 230 V, AC 240 V (50/60 Hz) Power Consumption 47 W Dimensions (including piano stand) * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. 1387 (W) x 400 (D) x 995 (H) mm (with Music Rest) 54-5/8 (W) x 15-3/4 (D) x 39-3/16 (H) inches 1387 (W) x 400 (D) x 808 (H) mm (without Music Rest) 54-5/8 (W) x 15-3/4 (D) x 31-13/16 (H) inches Weight (including the dedicated stand) 46 kg / 102 lbs Accessories Owner’s manual, Power Cord, Headphones Hook, Music Rest, Music Rest attachment screws 47 RP101_e.book 48 ページ 2007年4月4日 水曜日 午前11時50分 48 Index A AC Inlet ............................................................... 11–12 Adjuster ..................................................................... 15 Audio Equipment ........................................................ 37 B Beat .......................................................................... 26 Brilliance ................................................................... 20 C Composer Out ............................................................ 40 Computer .................................................................. 40 Control Panel ............................................................. 11 Count-in Recording ..................................................... 30 D Damper Pedal ............................................................ 14 Damper Resonance ............................................... 14, 34 Dual Balance ............................................................. 19 Dual Play ............................................................. 18–19 E Erasing Recorded Performance ........................................... 31 F Factory Reset .............................................................. 36 H Headphone Hook ....................................................... 13 Headphones .............................................................. 13 I Input Jack ............................................................ 11, 37 Internal Song .............................................................. 16 K Key Touch .................................................................. 22 L Lid ............................................................................ 12 Local Control .............................................................. 39 Local Off ................................................................... 39 Local On ................................................................... 39 M Master Tuning ............................................................ 32 Memory Backup ......................................................... 36 Metronome ................................................................ 26 Beat ..................................................................... 26 Tempo ............................................................ 27–29 Volume ................................................................. 27 [METRONOME] Button ....... 11, 23, 26–30, 32–36, 38–40 MIDI .......................................................................... 38 MIDI Channel ............................................................. 38 MIDI Connector .................................................... 11, 38 MIDI Devices .............................................................. 38 Music Rest ................................................................. 12 O Output Jack ......................................................... 11, 37 P Panel Lock ................................................................. 35 Pedal ........................................................................ 14 Pedal Connector ................................................... 11–12 Pedal Cord ................................................................ 12 Phones Jack ......................................................... 11, 13 Playing Back Internal Song ........................................................ 16 Recorded Performance ........................................... 31 Power ....................................................................... 14 Power Cord ............................................................... 12 [POWER] Switch ............................................ 11, 14, 35 R Rear Panel ................................................................. 11 Recording .................................................................. 30 Reverb ...................................................................... 21 Depth ................................................................... 21 [REVERB/KEY TOUCH] Button ... 11, 21–23, 32–35, 38–40 S Soft Pedal .................................................................. 14 [SONG] Button .................................. 11, 16, 30–31, 36 Sostenuto Pedal .......................................................... 14 Standard Pitch ............................................................ 32 Stretch Tuning ............................................................ 34 T Tap Tempo ................................................................ 29 Temperament ............................................................. 33 Tempo ....................................................................... 27 Tone ......................................................................... 17 Tone 1 ...................................................................... 19 Tone 2 ...................................................................... 19 [TONE] Button ......................... 11, 17–20, 24–25, 31, 35 Tonic ......................................................................... 33 Transpose .................................................................. 23 Tuning ....................................................................... 32 Tuning Curve ............................................................. 34 Twin Piano ................................................................. 24 Twin Piano Mode ................................................. 24–25 V V-LINK ....................................................................... 35 Volume ...................................................................... 14 Metronome ........................................................... 27 [VOLUME] Knob ................................................... 11, 14 RP101_e.book 49 ページ 2007年4月4日 水曜日 午前11時50分 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. AFRICA PHILIPPINES CURACAO URUGUAY NORWAY JORDAN G.A. Yupangco & Co. Inc. Zeelandia Music Center Inc. Todo Musica S.A. Roland Scandinavia Avd. MUSIC HOUSE CO. LTD. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION 339 Gil J. Puyat Avenue Orionweg 30 Francisco Acuna de Figueroa Kontor Norge FREDDY FOR MUSIC Makati, Metro Manila 1200, Curacao, Netherland Antilles 1771 Lilleakerveien 2 Postboks 95 P. O. Box 922846 PHILIPPINES TEL:(305)5926866 C.P.: 11.800 Lilleaker N-0216 Oslo Amman 11192 JORDAN TEL: (02) 899 9801 DOMINICAN REPUBLIC SINGAPORE Instrumentos Fernando Giraldez SWEE LEE MUSIC Calle Proyecto Central No.3 COMPANY PTE. LTD. 150 Sims Drive, Maison FO - YAM Marcel SINGAPORE 387381 25 Rue Jules Hermann, TEL: 6846-3676 Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SOUTH AFRICA TAIWAN ROLAND TAIWAN ENTERPRISE CO., LTD. Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, T.O.M.S. Sound & Music TAIWAN, R.O.C. (Pty)Ltd. TEL: (02) 2561 3339 2 ASTRON ROAD DENVER JOHANNESBURG ZA 2195, SOUTH AFRICA TEL: (011)417 3400 FAX: (011)417 3462 THAILAND Theera Music Co. , Ltd. 330 Soi Verng NakornKasem, New Road, Sumpantawongse, Bangkok 10100, THAILAND Paul Bothner(PTY)Ltd. TEL: (02) 224-8821 Royal Cape Park, Unit 24 Londonderry Road, Ottery 7800 Cape Town, SOUTH AFRICA TEL: (021) 799 4900 AUSTRALIA/ CHINA NEW ZEALAND Roland Corporation Roland Shanghai Electronics Australia Pty.,Ltd. Co.,Ltd. 38 Campbell Avenue 5F. No.1500 Pingliang Road Dee Why West. NSW 2099 Shanghai 200090, CHINA AUSTRALIA TEL: (021) 5580-0800 For Australia Roland Shanghai Electronics Tel: (02) 9982 8266 Co.,Ltd. For New Zealand (BEIJING OFFICE) Tel: (09) 3098 715 10F. No.18 3 Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL: (010) 6426-5050 HONG KONG Tom Lee Music Co., Ltd. Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911 ARGENTINA Instrumentos Musicales S.A. Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700 Parsons Music Ltd. BARBADOS 8th Floor, Railway Plaza, 39 Chatham Road South, T.S.T, Kowloon, HONG KONG TEL: 2333 1863 A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St.Michael, Barbados TEL: (246)430-1100 INDIA BRAZIL Rivera Digitec (India) Pvt. Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051 Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666 INDONESIA PT Citra IntiRama J1. Cideng Timur No. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170 CHILE Comercial Fancy II S.A. Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540 KOREA Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855 COLOMBIA Centro Musical Ltda. Cra 43 B No 25 A 41 Bododega 9 Medellin, Colombia TEL: (574)3812529 MALAYSIA Roland Asia Pacific Sdn. Bhd. 45-1, Block C2, Jalan PJU 1/39, Dataran Prima, 47301 Petaling Jaya, Selangor, MALAYSIA TEL: (03) 7805-3263 COSTA RICA JUAN Bansbach Instrumentos Musicales Ave.1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211 Montevideo, URUGUAY TEL: (02) 924-2335 VENEZUELA NORWAY TEL: 2273 0074 POLAND TEL: (06) 5692696 KUWAIT EASA HUSAIN AL-YOUSIFI Ens.La Esperilla Santo Domingo, Dominican Republic TEL:(809) 683 0305 Instrumentos Musicales ROLAND POLSKA SP. Z O.O. & SONS CO. Allegro,C.A. UL. Gibraltarska 4. Abdullah Salem Street, Av.las industrias edf.Guitar PL-03 664 Warszawa Safat, KUWAIT import POLAND TEL: 243-6399 ECUADOR Mas Musika Rumichaca 822 y Zaruma #7 zona Industrial de Turumo TEL: (022) 679 4419 Caracas, Venezuela TEL: (212) 244-1122 PORTUGAL Roland Iberia, S.L. Guayaquil - Ecuador TEL:(593-4)2302364 EUROPE EL SALVADOR Portugal Office Cais das Pedras, 8/9-1 Dto 4050-465, Porto, PORTUGAL OMNI MUSIC 75 Avenida Norte y Final Alameda Juan Pablo II, Edificio No.4010 San Salvador, EL SALVADOR TEL: 262-0788 GUATEMALA Casa Instrumental Calzada Roosevelt 34-01,zona 11 Ciudad de Guatemala Guatemala TEL:(502) 599-2888 HONDURAS Almacen Pajaro Azul S.A. de C.V. BO.Paz Barahona 3 Ave.11 Calle S.O San Pedro Sula, Honduras TEL: (504) 553-2029 MARTINIQUE Musique & Son Z.I.Les Mangle 97232 Le Lamantin Martinique F.W.I. TEL: 596 596 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F.W.I. TEL: 596 596 715222 MEXICO Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699 NICARAGUA Bansbach Instrumentos Musicales Nicaragua Altamira D'Este Calle Principal de la Farmacia 5ta.Avenida 1 Cuadra al Lago.#503 Managua, Nicaragua TEL: (505)277-2557 PANAMA SUPRO MUNDIAL, S.A. Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101 PARAGUAY Distribuidora De Instrumentos Musicales J.E. Olear y ESQ. Manduvira Asuncion PARAGUAY TEL: (595) 21 492147 PERU Audionet Distribuciones Musicales SAC Juan Fanning 530 Miraflores Lima - Peru TEL: (511) 4461388 TRINIDAD AMR Ltd Ground Floor Maritime Plaza Barataria Trinidad W.I. TEL: (868) 638 6385 LEBANON Chahine S.A.L. Gerge Zeidan St., Chahine Bldg., Achrafieh, P.O.Box: 16- 5857 Beirut, LEBANON AUSTRIA TEL: 22 608 00 60 TEL: (01) 20-1441 Roland Elektronische ROMANIA Musikinstrumente HmbH. FBS LINES Austrian Office Piata Libertatii 1, Eduard-Bodem-Gasse 8, 535500 Gheorgheni, A-6020 Innsbruck, AUSTRIA ROMANIA TEL: (0512) 26 44 260 TEL: (266) 364 609 OMAN TALENTZ CENTRE L.L.C. Malatan House No.1 Al Noor Street, Ruwi SULTANATE OF OMAN TEL: 2478 3443 BELGIUM/FRANCE/ RUSSIA QATAR AUSTRALIA/ NEW ZEALAND HOLLAND/ MuTek Al Emadi Co. (Badie Studio & LUXEMBOURG Roland Central Europe N.V. Houtstraat 3, B-2260, Oevel Dorozhnaya ul.3,korp.6 117 545 Moscow, RUSSIA TEL: (095) 981-4967 Stores) P.O. Box 62, Doha, QATAR TEL: 4423-554 (Westerlo) BELGIUM TEL: (014) 575811 CROATIA ART-CENTAR Degenova 3. SLOVAKIA DAN Acoustic s.r.o. Povazská 18. SK - 940 01 Nové Zámky TEL: (035) 6424 330 SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg., 1st Floor, Alkhobar, CENTRAL/LATIN AMERICA HR - 10000 Zagreb TEL: (1) 466 8493 CZECH REP. CZECH REPUBLIC DISTRIBUTOR s.r.o Voctárova 247/16 CZ - 180 00 PRAHA 8, CZECH REP. TEL: (2) 830 20270 DENMARK Roland Scandinavia A/S SPAIN SAUDI ARABIA Roland Iberia, S.L. Paseo García Faria, 33-35 08005 Barcelona SPAIN TEL: 93 493 91 00 P.O.Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081 SWEDEN Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20 SYRIA Technical Light & Sound Center Rawda, Abdul Qader Jazairi St. Bldg. No. 21, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384 Nordhavnsvej 7, Postbox 880, SWITZERLAND DK-2100 Copenhagen Roland (Switzerland) AG DENMARK Landstrasse 5, Postfach, TEL: 3916 6200 CH-4452 Itingen, FINLAND Roland Scandinavia As, Filial SWITZERLAND TEL: (061) 927-8383 Finland UKRAINE Elannontie 5 EURHYTHMICS Ltd. FIN-01510 Vantaa, FINLAND P.O.Box: 37-a. TEL: (0)9 68 24 020 Nedecey Str. 30 GERMANY Roland Elektronische UA - 89600 Mukachevo, UKRAINE TEL: (03131) 414-40 TURKEY ZUHAL DIS TICARET A.S. Galip Dede Cad. No.37 Beyoglu - Istanbul / TURKEY TEL: (0212) 249 85 10 U.A.E. Zak Electronics & Musical Instruments Co. L.L.C. Zabeel Road, Al Sherooq Bldg., No. 14, Grand Floor, Dubai, U.A.E. TEL: (04) 3360715 Musikinstrumente HmbH. Oststrasse 96, 22844 UNITED KINGDOM Norderstedt, GERMANY Roland (U.K.) Ltd. TEL: (040) 52 60090 Atlantic Close, Swansea GREECE/CYPRUS Enterprise Park, SWANSEA SA7 9FJ, CANADA STOLLAS S.A. UNITED KINGDOM Music Sound Light TEL: (01792) 702701 155, New National Road Patras 26442, GREECE TEL: 2610 435400 MIDDLE EAST HUNGARY Roland Canada Ltd. (Head Office) 5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) 270 6626 Roland East Europe Ltd. Warehouse Area ‘DEPO’ Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011 IRELAND BAHRAIN Roland Canada Ltd. Moon Stores No.16, Bab Al Bahrain Avenue, P.O.Box 247, Manama 304, State of BAHRAIN TEL: 17 211 005 (Toronto Office) 170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707 Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444 ITALY IRAN U. S. A. MOCO INC. No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169 ASIA Roland Corporation U.S. 5100 S. Eastern Avenue Los Angeles, CA 90040-2938, U. S. A. TEL: (323) 890 3700 Roland Italy S. p. A. Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300 ISRAEL Halilit P. Greenspoon & Sons Ltd. 8 Retzif Ha'aliya Hashnya St. Tel-Aviv-Yafo ISRAEL TEL: (03) 6823666 NORTH AMERICA As of November 1, 2006 (ROLAND) RP101_e.book 50 ページ 2007年4月4日 水曜日 午前11時50分 For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit. For Canada NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. For EU Countries SE

UK FI

DEHUFRPLITCZSKES EEPTLTNLLVDKSI NOGR Cover1,4 * 0 4 5 6 4 7 7 8 - 0 2 * 04564778 07-04-2N


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply