ROLAND MC-707 (01) PDF MANUAL

ROLAND MC-707 (01) PDF SUMMARY:

How do you output the sound of a track specified as CUE from MIX OUT?

The following parameter is added to the system settings (CTRL tab):

Parameter	Value	Explanation
Output Cue To Mix Out	ON, OFF	Specifies whether the sound of a track for which CUE is specified is output (ON) to MIX OUT or is not output (OFF).

How do you change all events in a step?

By holding down the [FUNC] button and turning a [C1]–[C4] knob, the value of all events in the currently-edited step can be changed together.

How do you set the START value to “0.”?

1. Hold down the [CLEAR] button and turn the [C3] knob.

How do you copy a step?

1. Hold down the [FUNC] button and press the [ ] button to copy the currently-edited step.
2. Hold down the [FUNC] button and press the [ ] button to paste to the currently-selected step.

Can copying a step be executed in any clip?

No, copying a step can be executed only within the same clip.

How do you edit notes from a connected MIDI device?

You can edit notes from a MIDI keyboard or other device connected to the MIDI port.

The following parameter is added to the system settings (MIDI tab):

Parameter	Value	Explanation
Edit Note	ON, OFF	Specifies whether input from an external device is used (ON) or not used (OFF) when editing notes in a TONE track.

What new waveforms are added for Motion Designer?

• COS: A waveform whose phase is 90 degrees offset relative to SIN.
• S&H: A random value is output.

How do you import SCATTER settings?

In the SCATTER edit screen, you can select the browser icon ( ) and import SCATTER settings from a project on the SD card.

How do you initialize values in the SCATTER PAD/STEP edit screen?

By holding down the [CLEAR] button and pressing a [C1]–[C4] knob, you can initialize the values individually.

When can you use “RETRIG GLD”?

When the “REVERSE” setting is “ON,” you can now use “RETRIG GLD.”

How do you use a metronome function?

You can now use a metronome function by holding down the [FUNC] button and pressing the [TEMPO] button. The metronome operates and sounds in synchronization with the master clock.

How do you turn the metronome on and off?

The following parameter is added to the master clock settings.

Parameter	Value	Explanation
METRONOME	ON, OFF	Specifies whether the metronome is used (ON) or not used (OFF).

How do you change the tone of the metronome?

The following parameters are added to the system settings (CTRL tab).

Parameter	Value	Explanation
Metronome Type	TYPE1–9	Specifies the tone of the metronome.

How do you change the volume of the metronome?

The following parameters are added to the system settings (CTRL tab).

Parameter	Value	Explanation
Metronome Level	1-127	Specifies the volume of the metronome.

How do you play a selected step as a loop?

When playing a tone/drum track, you can play the selected step as a loop. You can specify the step for each track.

1. Press the [START/STOP] button to play the project.
2. Hold down the [SEL] button and press the [STEP] button.

Loop playback starts for the selected step. If you select multiple steps, playback will loop in order of the selected steps. When you take your finger off the [STEP] button, pattern playback resumes.

How do you change the MEASURE of a clip?

When you change the MEASURE of a clip, the clip’s STEP LENGTH is now specified in tandem.

How do you temporarily set the sequencer’s playback mode to random?

Hold down the SEL button of the tone/drum track, and press the MEASURE [>] button.

How do you temporarily set the sequencer’s playback mode to reverse?

Hold down the SEL button of the tone/drum track, and press the MEASURE [<] button.

How do you enter a SubStep in the drum track?

In NOTE mode, hold down the [NOTE] button and press the [STEP] button.

How do you enter MUTE (50%) to a drum track?

In NOTE mode, hold down the [MUTE] button and press the [STEP] button.

How do you invert MUTE for all tracks?

Hold down the [FUNC] button and press the [MUTE] button.

How do you switch the metronome on/off?

Hold down the [FUNC] button and press the [TEMPO] button.

How do you initialize the parameter assigned to a knob?

While holding down the [SHIFT] button and the [CLEAR] button, turn the [FILTER], [MOD], or [FX] knob.