RESPEKTA CH 99060 S A (01) PDF Document

The supplied accessories list for the RESPEKTA CH 99060 S A includes:

• Lower chimney a) and upper chimney b): 1
• Upper chimney bracket: 1
• Lower chimney stabilizer- and fixing bar: 1

The accessories list for the RESPEKTA CH 99060 S A includes the following items related to screws and plugs:

• Wall plug $\phi$8: 8
• Screw ST4$\times$40mm (2 for upper chimney mounting bracket, 2 for lower chimney mounting plate): 4
• Screw ST4$\times$30mm (2 pcs for hood hanging, 2 pcs for hood locking): 4
• ST4*8 screw (Upper- and lower Chimney fixing): 6

If the V-Flaps are not factory-mounted on the RESPEKTA CH 99060 S A, follow these steps:

Step 1. First install half part 1 in connection nozzle B10.

Step 2. Pins 3 must be in upwards position.

Step 3. Insert the axle 4 into the holes 5 on the nozzle B10.

Step 4. Repeat all operations for mounting the half part 2.

The steps for mounting the RESPEKTA CH 99060 S A for recirculation mode are as follows:

Step 1. Using pencil, draw a horizontal line on the wall at the height where the hood bottom edge should lie. It is best to use a water level. Observe minimum distance according to chapter 11.1 of the operating instructions.

Step 2. Hold the supplied drill template with the bottom edge on the drawn pencil line against the wall and mark the four drill holes.

Step 3. Drill a 30mm deep hole in the wall with an 8mm masonry drill at the 4 pencil marks. For safety, check the diameter of the plugs with a caliper gauge.

Step 4. Place one plug into each of the 4 holes.

Step 5. Screw one ST4 $\times$ 30mm screw each into the two dowels for the hood suspension. Attention! The screw heads must protrude 3 – 5 mm from the dowels so that the hood can be hung on them. Readjust after the hood has been hung up if necessary.

Step 6. Hang the hood with the two eyelets on its back by the two screws on the wall.

Step 7. Mount the stabilizer- and mounting plate at the top of the lower flue with two ST4 * 8mm screws.

Step 8. Place the lower chimney shaft on the hood.

Step 9. Firmly press the chimney shaft against the wall and mark with pencil the two drill holes through the holes in the chimney stabilize- and mounting plate.

Step 10. Remove the chimney from the hood.

Step 11. Drill two 40mm deep holes into the wall at the marked locations using an 8mm masonry drill.

Step 12. Push the upper (inner) chimney shaft from above into the lower (outer) chimney shaft.

Step 13. Place the nested chimneys on the hood.

Step 14. Pull the inner chimney shaft straight up to the ceiling and place one marking line on the sides of the shaft.

Step 15. Remove the chimneys from the hood.

Step 16. Hold the upper (inner) chimney mounting bracket at the top center of the ceiling between the drawn marks and mark the drilled holes with the two holes in the mounting bracket a pencil.

Step 17. Using an 8mm masonry drill, drill two 40mm deep holes at the pencil markers and place two plugs.

Step 18. Fix the inner chimney mounting bracket to the wall with two ST4 $\times$ 40mm screws at the top of the ceiling.

Step 19. Place the two nested chimneys on the hood.

Step 20. Slide the inner chimney shaft all the way down.

Step 21. Attach the lower chimney stabilize- and mounting plate to the wall with two ST4 x 40mm screws.

Step 22. Fix the lower chimney shaft with two ST4 * 8mm screws on the sides of the hood.

Step 23. Pull the upper (inner) chimney shaft all the way up and secure it to the mounting bracket with two ST4 * 8mm screws.

Step 24. Secure the hood with two ST4 $\times$ 30mm screws through the 2 hood fixing eyelets.

Step 25. Mount the carbon filters on the sides of the motor. (See user’s manual chapter “Using the carbon filters”).

Before beginning the installation of the RESPEKTA CH 99060 S A, make sure the power supply is secure. This must be set up by a specialist.

To mount the RESPEKTA CH 99060 S A for exhaust air operation, proceed as follows during assembly:

Step 1. Remove the outer and inner chimney.

Step 2. Mount the exhaust hose. (Fig. k)

Step 3. Replace the outer and inner chimney.

Note that the wall duct must be dimensioned for a 150 mm exhaust hose (Drill hole about 155mm).

The mounting procedure is the same as described for recirculation mode, but without mounting the carbon filters.

For the final assembly of the RESPEKTA CH 99060 S A in exhaust air operation, an exhaust grille with a 150mm socket (a) for the connection of the exhaust air hose is needed. This is not included in the delivery.

The accessory list for the RESPEKTA CH 99060 S A includes:

• V-Flap: 1
• Air exhaust pipe: 1
• Ribbon-8$\times$550mm: 1