FREE ENGLISH REMINGTON HC5750 (02) PDF USER GUIDE
FREE ENGLISH REMINGTON HC5750 (02) PDF USER MANUAL
FREE ENGLISH REMINGTON HC5750 (02) PDF OWNER GUIDE
FREE ENGLISH REMINGTON HC5750 (02) PDF OWNER MANUAL
FREE ENGLISH REMINGTON HC5750 (02) PDF REFERENCE GUIDE
FREE ENGLISH REMINGTON HC5750 (02) PDF INSTRUCTION GUIDE
FREE ENGLISH REMINGTON HC5750 (02) PDF REFERENCE MANUAL
FREE ENGLISH REMINGTON HC5750 (02) PDF INSTRUCTION MANUAL
FREE ENGLISH REMINGTON HC5750 (02) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD REMINGTON HC5750 (02) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
REMINGTON HC5750 (02) PDF SUMMARY:
What should you do if an appliance falls into water?
Do not reach for an appliance that has fallen into water. Unplug it immediately.
Should you use the appliance while bathing or in the shower?
No, do not use while bathing or in the shower.
Where should you not place or store the appliance?
Do not place or store this appliance where it can fall or be pulled into a tub or sink.
When should you unplug the appliance from the electrical outlet?
Except when charging, always unplug this appliance from the electrical outlet immediately after using. Also, unplug this appliance before cleaning it.
Should an appliance be left unattended when plugged in?
An appliance should never be left unattended when it’s plugged in, except when charging a rechargeable appliance.
What should you do if the appliance has a damaged cord or plug, is not working properly, has been dropped or damaged, or has been dropped into water?
Return the appliance to an authorized service center for examination and repair.
Should you drop or insert any object into any of the appliance’s openings?
No, never drop or insert any object into any of the appliance’s openings.
Where should you not use the appliance?
Do not use outdoors or operate where aerosol (spray) products are being used, or where oxygen is being administered.
Where should you store the appliance and cord?
Make sure the cord is disconnected from the clipper while storing this appliance and cord in a moisture-free area.
What is the maximum temperature the appliance should be stored at?
Do not store it in temperatures exceeding 140°F (60°C).
Should you use the appliance with a damaged or broken cutter unit?
No, do not use this appliance with a damaged or broken cutter unit, as injury may occur.
What should you always make sure of with the blades?
Always make sure blades are aligned properly.
How should you attach the plug to the appliance and the adapter to the outlet?
Always attach plug to appliance and then the adapter to the outlet.
How should you disconnect the appliance?
To disconnect, turn all controls to OFF, then remove adapter from outlet, then detach power cord from the clipper for storage.
Should you use an extension cord or a voltage converter with the appliance?
No, do not use an extension cord or a voltage converter with this appliance.
Should you wrap the cord around the appliance?
No, do not wrap the cord around the appliance.
How should you dispose of used batteries?
Dispose of used batteries properly. Do not incinerate. Batteries may explode if overheated. Do not wrap in metal or aluminum foil. Wrap in newspaper before discarding. It is suggested that you contact local battery redemption site(s) in your area.
Should you run the product when charging via USB port on a PC?
No, do not run the product when charging via USB port on a PC. (For USB charging models only)
How do you attach guide combs?
To attach comb to clipper, align both comb rails with the comb tracks on both sides of the clipper and slide into place. Once comb is secure you will hear a click sound, letting you know it is locked in. Ensure comb is properly secured by pushing down on comb, the comb should not slip.
How do you adjust comb height?
To adjust comb height press down on the comb adjustment button and slide up or down as necessary.
What should you not run under the tap?
Do not run the entire unit under the tap, only the blade set is meant to be rinsed in water.
What should you add to the blades after rinsing with water?
Add oil, place a few drops of cutter or sewing machine oil onto the blades after rinsing with water.
What should you ensure when cleaning the hair clipper?
Ensure that the hair clipper is turned off when cleaning.
How do you remove the blade set for cleaning?
To remove the blade set, remove the two screws holding the large blade to the clipper body. The blade set will separate from the body and can be cleaned as necessary.
What should you do after removing the blade set?
Brush out hairs from between blades with the cleaning brush. Place a few drops of cutter or sewing machine oil onto the blades. Wipe off excess oil.
What should you not use on the cutters or cutter casing when cleaning?
Do not use liquid cleaners on the cutters or harsh or corrosive chemicals on the cutter casing.
What should you do with the charge adapter when not in use and when cleaning?
Unplug the charge adaptor from the power outlet when not in use and when cleaning.
Where should you always store the appliance and cord?
Always store this appliance and cord in a moisture-free area.
Should you wrap the cord of the charging adaptor around the appliance?
No, do not wrap the cord of the charging adaptor around the appliance.
What is the maximum temperature the appliance should be stored in?
Do not store in temperatures above 140ºF.
What should you do if the clipper does not work when turned on?
Clipper must be charged for a full 14-16 hours, or use clipper while plugged into wall.
What should you do if the clipper cutters do not move?
The cutting unit may be dirty and clogged. Clean the unit as directed in the Cleaning & Maintaining section.
What should you do if the clipper does not hold a charge?
Fully discharge battery by running clipper until it stops; then follow recharging instructions (see section on Charging Your Hair Clipper).
What should you do after each use?
Brush the accumulated hair from the cutters. Do not submerge the clipper in water.
How do you use the Click N’ Wash system?
Click the Click N’ Wash buttons that are located on the sides of the hair clipper head. The blades will slide out allowing the blade to be easily cleaned under the tap.
How do you lock the blades back into place after cleaning using the Click N’ Wash system?
Once the blades are cleaned, lock them back into place by pushing the blade set towards the clipper body. You will hear a “click” when blades are locked into place.
What should you do before removing the batteries from the clipper?
Ensure device is unplugged from any electrical outlet.
What should you do to remove the blade for ease of disassembly and safety?
Remove blade for ease of disassembly and safety by using a phillips screw driver and removing both screws.
What should you do after removing the blade?
Remove plastic screw plug from underside of unit, located under rating stamp using small flat head screw driver.
What should you do after removing the plastic screw plug?
Remove screw located under rating stamp from underside of unit.
How should you separate the body of the device into two halves?
Use flat head screw driver to pry apart the body of the device into its two halves.
What should you do after separating the body of the device?
Cut wires from the battery pack.
What is the final step in the battery removal process?
Remove battery pack from the device.
How should you charge your hair clipper?
Clipper must be turned off. Insert the adapter plug into the bottom of the clipper and plug the adapter unit into a power outlet. The amber light will glow to indicate that it is charging.
How long does it take to fully charge the clipper?
The clipper will be fully charged in 14-16 hours.
Can the batteries be overcharged?
The batteries cannot be overcharged, but we recommend that charging be discontinued if the clipper will not be used for a long period of time.
Is it advisable to use the clipper directly from the power outlet when it has been fully charged?
It is advisable not to use this clipper directly from the power outlet when it has been fully charged, but if while using the clipper in cordless mode there is a noticeable drop in power, you can use directly from the power outlet. Never use under water when connected to the outlet.
What should you do if the clipper has not been used for a month or longer?
If the clipper has not been used for a month or longer, it is advisable to recharge it for 14-16 hours.
How should you preserve the life of the batteries?
To preserve the life of the batteries, discharge them by running the clipper until the blades move slowly. Switch off and fully recharge. Do this every six months.
What temperature range should you charge the clipper at?
Charge the clipper at temperatures between 40º-90ºF.
Should you run the product when charging via USB port on a PC?
No, do not run the product when charging via USB port on a PC.
How do you use the hair texturizor?
Simply adjust the hair thinner mechanism by sliding the button at the top of the hair clipper. Cut hair to desired length. Select a comb attachment on to two lengths shorter than initial comb length and attach to clipper. Slide Texture Release button into place, exposing hair texturizor. Repeat hair cutting technique in areas you desire to be texturized.
How do you use the Auto Boost System (HC5750 only)?
If the clipper is set to Auto it will run at regular power under low load conditions. When more power is needed, the clipper with automatically sense and provide maximum Boost. If the clipper is set to Boost, it will run at maximum power at all times.
How do you use the Dual Boost System (HC5550 only)?
If the clipper is set to On, it will run at regular power. If the clipper is set to Boost, it will provide maximum power.
CLICK HERE TO DOWNLOAD REMINGTON HC5750 (02) PDF MANUAL