PROTECTA AK105A (01) PDF DOCUMENT

The PROTECTA AK105A Tripod is designed for use with Protecta approved components and subsystems only. Substitutions or replacements made with unauthorized components or subsystems may jeopardize compatibility of equipment and may affect the safety of the entire system.

You should plan your fall protection system before starting your work. Account for all factors that may affect your safety before, during, and after a fall. Refer to the figures in the user instructions for tripod set up, use, and takedown.

1. Grip the head of the tripod and lift the tripod assembly from the carrying bag.

2. Stand the tripod vertically. Swing each of the three legs out until each leg is in the locked position.

3. An audible “click” will be heard as each leg snaps into the locked position.

For all tripod legs to be secured in the locked position, each of the three leg locking pins must be flush with the top of the tripod head. Pins that are not flush are in the unlocked position.

The height of each tripod leg can be separately adjusted as needed.

1. To adjust the height of a leg, pull off the wire pin lock (C) on the leg height locking pin (D). Pull out the leg height locking pin completely. If the tripod is upright, support the tripod to prevent it from tipping over when the leg height locking pin is removed.

2. After the leg height locking pin has been removed, pull the telescoping leg out (E), or push it in, to achieve the required leg height.

3. Reinsert the leg height locking pin. Pin holes in the outer and inner leg tubes must align so that the pin can be reinserted. Pull the wire pin lock back over the exposed end of the leg height locking pin to secure it.

Repeat for each leg as necessary to bring the tripod to the required working height. Index numbers on each leg can be used as a visual aid during leg height adjustment.

The included leg chain is used to prevent the spread of the three tripod legs beyond their locked position.

1. Feed the chain through each of the chain retainers in the three tripod feet.

2. While keeping the tripod legs in position, pull the leg chain tight through the chain retainers. Secure the chain ends with the chain hook.

Confirm that the tripod is positioned on a firm surface.

The eyebolt anchor point at the center of the tripod head must be located centrally over the entry shaft or hole. Note: Only the center eyebolt anchor point can be used for fall arrest.

Confirm that there is adequate clearance between the tripod feet and the edge of the entry shaft or hole.

1. Close the entry point by replacing cover or blocking the entry shaft or hole.

2. Remove the entry safety equipment from the tripod eyebolt anchor point and bracket (if used).

3. Collapse the telescoping legs by removing the leg height locking pins and telescope the legs back to their lowest locking point. Insert pins.

4. Stand the tripod vertically and pull the leg locking pins up. Swing the legs inward to the center.

5. Place the tripod in the carrying bag for transportation or storage.

This product is part of a Personal Fall Arrest System. The user must read and follow the manufacturer’s instructions for each component or part of the complete system. These instructions must be provided to the user of this equipment. The user must read and understand these instructions or have them explained to them before using this equipment. Manufacturer’s instructions must be followed for proper use and maintenance of this product. Alterations or misuse of this product or failure to follow instructions may result in serious injury or death.

The PROTECTA AK105A Tripod is used for confined space shaft and manhole entry and retrieval. An optional Mounting Bracket can be used with the Tripod to mount an SRL as part of a Personal Fall Arrest System (PFAS) where a combination of worker mobility and fall protection is required. Mounting Brackets and SRLs are sold separately.

This equipment is intended to be used by persons trained in its correct application and use. It is the responsibility of the user to assure they are familiar with these instructions and are trained in the correct care and use of this equipment. Users must also be aware of the operating characteristics, application limits, and the consequences of improper use.

Always consider the product limitations and installation and use requirements specified in the installation and user instructions supplied with other components of the Personal Fall Arrest System (PFAS).

Before using the PROTECTA AK105A Tripod:

• Check all structural parts for damage, dents, cracked welds, bent or crushed tubes.

• Check all hardware (pins, screws, nuts, bolts, pulleys, rollers and brackets) for damaged threads, bent, damaged or missing fasteners and loose fasteners.

• Inspect all equipment for missing, damaged or otherwise illegible warning labels. Any damaged, missing or illegible labels must be replaced before using the tripod.

• Any winches, self-retracting lifelines (SRLs), work positioning or fall-arrest equipment used with your Protecta Tripod must be installed, inspected, maintained and operated according to the manufacturer’s instructions.

Perform a complete visual inspection as outlined in “Before using the Protecta Tripod.” Clean equipment as required, thoroughly inspect all welds, labels, pins, fasteners, brackets and parts. Record all findings on a copy of the “hoist inspection log.” If any problems are found with the equipment DO NOT USE until it has been repaired.

Clean the tripod thoroughly using a damp cloth and a mild soap solution. Perform a complete visual inspection as described in “Before using the Protecta Tripod”. More frequent inspections by a competent person may be required based on the nature and severity of workplace conditions affecting the equipment and the modes of use and exposure time of the equipment. Record all findings in Table 1 “Tripod Inspection Checklist.” If any problems are found do not use the tripod until it has been repaired.

Inspection:	User	Competent Person
Inspect for loose or missing fasteners, pins and bent or damaged parts.	☐	☐
Inspect for dents, distortion, cracks, corrosion or other damage.	☐	☐
Inspect for smooth operation of leg locking pins.	☐	☐
All labels must be present and fully legible (labels identified in Figure 8).	☐	☐
Corrective Action/Maintenance:	Approved By: Date:
Corrective Action/Maintenance:	Approved By: Date:
Corrective Action/Maintenance:	Approved By: Date:
Corrective Action/Maintenance:	Approved By: Date:
Corrective Action/Maintenance:	Approved By: Date:
Corrective Action/Maintenance:	Approved By: Date:

Tripod Legs: Anodized Aluminum

Tripod Head: Cast Aluminum

Maximum Load: 1 or 2 users

Working Height: 53″ to 92.5″ (1.35 to 2.35 m)

Weight: 30 lbs (13.5 kg)

Packaged Length: 67″ (1.7 m)

Test Standard: Z359.1-2007, Z359.4-2007

Height Setting Points: 1 – 8

Working Field: 1.54 m min. to 2.68 m max.