PROLIGHTS SMARTBATPLUS (01) PDF MANUAL

The products referred to in this manual conform to the European Community Directives and are therefore marked with CE.

The supply voltage of this product is DC24V; never connect it directly to AC220V. Leave servicing to skilled personnel only. Never make any modifications on the unit not described in this instruction manual, otherwise you will risk an electric shock.

Connection of the power adapter must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

The connection to the main network of electric distribution must be carried out by a qualified electrical installer. Check that the voltage corresponds to those for which the unit is designed as given on the electrical data label.

This unit is not for home use, only professional applications.

Never use the fixture under the following conditions: in places subject to vibrations or bumps, or in places subject to excessive humidity.

Make certain that no inflammable liquids, water or metal objects enter the fixture.

Do not dismantle or modify the fixture.

All work must always be carried out by qualified technical personnel. Contact the nearest sales point for an inspection or contact the manufacturer directly.

If the unit is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.

If this device will be operated in any way different to the one described in this manual, it may suffer damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short circuit, burns, electric shock, etc.

Before starting any maintenance work or cleaning the projector, cut off power from the main supply.

Always additionally secure the projector with the safety rope. When carrying out any work, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country in which the fixture’s being used.

Install the fixture in a well ventilated place.

Keep any inflammable material at a safe distance from the fixture.

Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired.

The lamp (LED) shall be changed if it has become damaged or thermally deformed.

Never look directly at the light beam. Please note that fast changes in lighting, e.g., flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.

Do not touch the product’s housing when operating because it may be very hot.

The operating elements and connections are:

• CONTROL PANEL: with display and 4 buttons used to access the control panel functions and manage them.

• Adjustable foot support: for tilt regulation (up to 20°).

• ON/OFF SWITCH.

• CHARGING CONTACT

• RELEASE LEVER: to adjustable foot support

• CARRYING HANDLE

• IR SENSOR

• Wireless DMX RECEIVER

The SMARTBATPLUS may be set up on a solid and even surface. The unit can also be mounted upside down to a cross arm. For fixing, stable mounting clips are required. The mounting place must be of sufficient stability and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country in which the fixture’s being used.

Always additionally secure the projector with the safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

Switch on the SMARTBATPLUS with the power switch. The unit is ready for operation and can be operated via a DMX controller or it independently performs its show program in succession. After operation, switch off the unit with the power switch.

To recharge SMARTBAT:

• connect the unit to the special battery charger through the lower connector

• connect the battery charger to the power supply

The charging time is 4h and autonomy is 12h.

The Flight-case SMARTBATPLUSPACK is designed to contain 6pcs SMARTBATPLUS with battery charger kit included.

• It has internal separated compartments with charger plug for every device.

• The case power input is Powercon IN.

• Dimensions (LxHxD) are 537x540x470 mm.

Always charge with the flight-case open.

To access this built-in automatic program:

• Press the MENU button so many times until [Autoshow] shows on the display.

• Press the ENTER button to confirm.

• Using the UP/DOWN button, select one of the programs [Auto 1 – Auto 5].

• Press the ENTER button to save the setting.

• Using the UP/DOWN button, select the speed value of the show [S1 – S100].

• Press the ENTER button to save the setting.

To access custom static color settings from pre-programmed presets:

• Press the MENU button so many times until [Static] shows on the display.

• Press the ENTER button to confirm.

• Press the MENU button so many times until [Fixed Color] shows.

• Press the ENTER button to confirm.

• Using the UP/DOWN button, select one of the programs [R,G,B,W,…,RGB,…,RGBW].

• Press the ENTER button to save the setting.

To set the personal balance of the color:

• Press the MENU button so many times until the display shows [Static].

• Press the ENTER button to confirm.

• Press the MENU button so many times until the display shows [Manual Color].

• Press the ENTER button to confirm.

• Using the UP/DOWN button, select one of the programs [R,G,B,W].

• Press the ENTER button to confirm.

• Using the UP/DOWN button, select the wanted value of the program [000-255].

• Press the ENTER button to save the setting and to pass to the successive color.

• Continue until you obtain the wanted color mix.

To start up the IR receiver:

• Press the MENU button so many times until the display shows [IR Setup].

• Press the ENTER button to confirm.

• Press the UP/DOWN button, select one of the programs [ON] or [OFF].

• Press the ENTER button for save the setting.

Make sure to point the controller directly at the receiver on the product.

To set the wireless mode:

• Press the MODE button until the display shows Wireless Setting, then press the ENTER button.

• Use the UP/DOWN button until the display reads Wireless Receive, and then press the ENTER button and select the ON mode.

• Press the MODE button to go back or to meet the waiting time to exit the setup menu. After you complete these steps, you have to synchronize with any wifi unit with which you want to communicate by pressing the sync button present on the same. Then connect any DMX console to wifi unit to open the communication with the SMARTBATPLUS unit.

To reset the unit:

• Press the MODE button until the display shows Wireless Reset, then press the ENTER button.

• Use the UP/DOWN button until the display reads Yes, and then press the ENTER button.

• Press the MODE button to go back or to meet the waiting time to exit the setup menu.

To enter Dimmer mode to select specific dimming curve:

• Press the MENU button so many times until [DIMMER MODE] shows, and press the ENTER button to confirm.

• Press the UP/DOWN button to select [Off – Dimer 1 – Dimmer 2 – Dimmer 3].

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To enter DMX mode:

• Press the MENU button so many times until [DMX Channel] shows, and press the ENTER button to confirm.

• Press the UP/DOWN button to select the desired DMX mode [4Ch], [6Ch], [10Ch], [HSV], [HSI] and press the ENTER button to save the setting.

To operate the SMARTBATPLUS with a light controller, set the unit DMX start address for the first DMX channel. To set the start address:

• Use the UP/DOWN button until the display reads [DMX Address] and then press the ENTER button to confirm.

• Press the UP/DOWN button to select the value [d 1-509] and then press the ENTER button.

If e.g., address 33 on the controller is provided for controlling the function of the first DMX channel, adjust the start address 33 on the SMARTBAT. The other functions of the light effect panel are then automatically assigned to the following addresses.

To activate/deactivate the access password:

• Press the MODE button so many times until [Key Lock] shows, and press the ENTER button to confirm.

• Use the UP/DOWN button to select: ON or OFF.

• Press the ENTER button to confirm the selection.

When the fixture is set as pass ON, after 30 seconds or next turn on, the fixture will need an access password to enter the display menu control. The factory access password is UP + DOWN + UP + DOWN (press ENTER to confirm the access).

During maintenance, make sure the area below the installation place is free from unwanted persons. Switch off the unit, unplug the main cable and wait until the unit has cooled down. All screws used for installing the device and any of its parts should be tightly fastened and should not be corroded. Housings, fixations and installation spots (ceiling, trusses, suspensions) should be totally free from any deformation. The main cables must be in impeccable condition and should be replaced immediately even when a small problem is detected.

It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or other particles to ensure the light is radiated at maximum brightness. For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.

Any new fixture containing a Lithium battery should be initialized when first purchased to maximize its battery life. To do this:

1. Fully charge the unit for a minimum of 5 to 6 hours.

2. Fully discharge, then fully recharge the battery.

3. Repeat this cycle another 2 times for optimum battery life.

Lithium batteries perform best when in regular use. Long idle periods will reduce the battery life.

Recharge the battery at the earliest opportunity, leaving batteries discharged for long periods will reduce battery life.

Store units containing Lithium batteries at cool temperatures. High ambient temperatures significantly reduce the life of a Lithium battery.

Disconnect power from the unit when charging is complete.

Do not use fixtures whilst charging.

Charge your fixture’s battery to around 50%. If you store a fixture with a fully discharged battery, it could fall into a deep discharge state. If you store it fully charged, the battery may lose some capacity, leading to shorter battery life.

Power down the device to avoid additional battery use.

Place your device in a cool, moisture-free environment that’s less than 32° C (90° F).