FREE ENGLISH PROFLO PFXT5 (01) PDF USER GUIDE
FREE ENGLISH PROFLO PFXT5 (01) PDF USER MANUAL
FREE ENGLISH PROFLO PFXT5 (01) PDF OWNER GUIDE
FREE ENGLISH PROFLO PFXT5 (01) PDF OWNER MANUAL
FREE ENGLISH PROFLO PFXT5 (01) PDF REFERENCE GUIDE
FREE ENGLISH PROFLO PFXT5 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH PROFLO PFXT5 (01) PDF REFERENCE MANUAL
FREE ENGLISH PROFLO PFXT5 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH PROFLO PFXT5 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD PROFLO PFXT5 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
PROFLO PFXT5 (01) PDF SUMMARY:
What does the safety alert symbol indicate?
This symbol is used to alert you to potential personal injury and other hazards. Obey all safety messages that follow this symbol to reduce the risk of personal injury as well as property damage.
What should you do before using the product?
Read carefully the product installation, operating and maintenance manual.
What can happen if you fail to follow the instructions and warnings in the manual?
Failure to follow the instructions and warnings in the manual may result in serious or fatal injury and/or property damage, and will void the product warranty.
Who should install the product?
This product must be installed by a licensed professional.
What codes and regulations should you follow when installing the product?
Follow all applicable local and state codes and regulations. In the absence of such codes, follow the current editions of the National Plumbing Code and National Electric Code, as applicable.
What can happen if the product corrodes, weakens, bursts, or explodes?
It may cause serious or fatal injury, leaking or flooding and/or property damage.
What should be done to minimize risk when installing the product?
A licensed professional must install and periodically inspect and service the product. A drip pan connected to an adequate drain must be installed if leaking or flooding could cause property damage.
Where should the product NOT be located?
Do not locate in an area where leaking could cause property damage to the area adjacent to the appliance or to lower floors of the structure.
What must be installed to prevent excessive pressure?
A relief valve must be installed to prevent pressure in excess of local code requirement or maximum working pressure designated in the Product Manual, whichever is less.
What temperature conditions should the product not be exposed to?
Do not expose the product to freezing temperatures or temperatures in excess of 130° F.
When can you adjust the pre-charge or re-pressure the product?
Do not adjust the pre-charge or re-pressure this product except for any adjustments required at the time of initial installation, especially if the product is corroded, damaged, or with diminished integrity. Adjustments to pre-charge must be done at ambient temperature only.
What can happen if you do not properly size the product or follow instructions?
Failure to properly size the product or follow these instructions may result in excessive strain on the system lead to product failure, serious or fatal personal injury, leakage and/or property damage.
How can water quality affect the product?
The water quality can significantly influence the life of this product.
What should you test your water for?
You should test for corrosive elements, acidity, total solids and other relevant contaminants, including chlorine.
What should you do to your water to ensure satisfactory performance and prevent premature failure?
Treat your water appropriately.
What should you do if there is shipping damage to the product?
Inspect for shipping damage and notify freight carrier or store where purchased immediately if damage is present.
What should you do if the product appears to be malfunctioning or shows signs of corrosion?
To avoid risk of personal injury and property damage, if the product appears to be malfunctioning or shows signs of corrosion, call a licensed professional immediately.
What should be used with the product?
Use only with potable water system.
What temperature and pressure limits should you adhere to?
Do not operate in a setting with freezing temperatures or where the temperature can exceed 130°F and do not exceed the maximum working pressure specified for this product.
How often should the temperature and pressure relief valve be inspected?
At least once every 3 years or if discharge is present, a licensed contractor should inspect the temperature and pressure relief valve and replace if corrosion is evident or the valve does not function.
What can happen if you fail to inspect the temperature and pressure relief valve as directed?
Failure to inspect this valve as directed could result in unsafe temperature or pressure build-up which can result in product failure, serious injury or death and/or severe property damage and void the product warranty.
What chemical is this product known to expose you to?
This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm.
Where can you go for more information regarding the chemicals in the product?
For more information go to http://www.P65Warnings.ca.gov.
What are the pre-installation steps?
- Ensure expansion tank is sized properly for application (see Figure 1).
- Remove plastic cap from air valve.
- With expansion tank empty of water, adjust air precharge to match cold water supply pressure.
- Replace and tighten plastic cap on air valve.
What happens if the valve cap is not properly sealed?
Failure to properly seal valve cap will result in loss of precharge causing product to fail.
How should the expansion tank be installed?
Install the expansion tank on the cold water supply line to the water heater at a point between the water heater and backflow preventer or other one-way device (see Figure 2.) Mount tank vertically only.
What should you check after the expansion tank is installed?
Once the expansion tank is installed, check the cold water supply line for any leakage. Make repairs if necessary.
What should you do before the initial firing of the water heater?
Before the initial firing of the water heater, open any hot water fixture and draw water until all air is removed from the system.
What should you do after removing the air from the system?
Turn the water heater temperature control to desired ending temperature level, (see water heater instructions). Do not set temperature higher than that which the expansion tank was originally sized.
How can you relieve initial thermal expansion?
To relieve initial thermal expansion, slightly open a hot water faucet. Continue until water heater aquastat temperature is satisfied.
When is no further bleeding of expanded water required?
Once the heater is at its operating range, no further bleeding of expanded water is required.
What is the function of the expansion tank?
The expansion tank will control pressure increases caused by thermal expansion to a level below the water heater relief valve setting.
How often should a professional plumber check the system?
A professional plumber should check the complete system, including the expansion tank, yearly and more frequently as the system ages.
What should installers do with the manual?
Installer: Leave this manual with the owner.
What is the warranty period for the product?
Subject to the limitations herein, Seller warrants that items manufactured by Seller (“Product”) shall be free from defects in design, material and workmanship under Normal Use for a period of one (1) year from the date of sale (“Warranty Period”).
What does the seller disclaim?
SELLER HEREBY DISCLAIMS ALL OTHER EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OR FITNESS FOR A PARTICULAR PURPOSE.
Under what conditions is the limited warranty void?
This limited warranty is void for any damage caused by misuse, abuse, neglect, acts of God, use with flammable or corrosive liquids, or improper installation.
What does “Normal Use” mean?
“Normal Use” means in strict accordance with the installation, operation and maintenance manual.
What should you do if you have a warranty claim?
To file a claim, first contact your insurance company (if property damage or bodily injury) then contact your servicing branch or the location where you purchased the Product.
What is the buyer’s sole remedy from the seller?
Buyer’s sole and exclusive remedy from Seller is included herein.
What is the seller NOT liable for?
Seller makes NO ADDITIONAL ALLOWANCE FOR THE LABOR OR EXPENSE OF REPLACING DEFECTIVE PRODUCTS OR DAMAGE RESULTING FROM THE SAME. UNDER NO CIRCUMSTANCES SHALL EITHER PARTY BE LIABLE TO THE OTHER FOR INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND.
What is the limit of the seller’s liability?
BUYER HEREBY ACKNOWLEDGES AND AGREES THAT SELLER’S LIABILITY, IF ANY, SHALL NOT EXCEED THE NET SALES PRICE OF THE DEFECTIVE PRODUCT(S).
What does the buyer acknowledge regarding product suitability?
Buyer acknowledges that Buyer ultimately chooses the product’s suitability for its particular use, as normally signified by the signature of Buyer’s technical representative.
Are recommendations by the seller construed as warranties?
Any recommendations made by Seller concerning the use, design, application or operation of the products shall not be construed as representations or warranties, expressed or implied.
What does failure by the seller to make recommendations or give advice not impose?
Failure by Seller to make recommendations or give advice to Buyer shall not impose any liability upon Seller.
What does the seller not make any warranty or representation regarding?
Seller makes no warranty or representation with regard to the product meeting code requirements.
What must products containing brass or bronze without “LF” in the description not be used for?
Such products must not be used in potable water applications.
CLICK HERE TO DOWNLOAD PROFLO PFXT5 (01) PDF MANUAL