Free English PRO-LIFT C-2701 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD PRO-LIFT C-2701 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the essential safety precautions for using the PRO-LIFT C-2701?
When using the PRO-LIFT C-2701, it is important to follow these safety precautions:
• Read, understand, and follow all instructions before operating this device.
• Do not exceed the rated capacity of 300 lbs.
• Use only on a hard, level surface. Do not use on soft surfaces as the stool may become unstable.
• This product is designed only for sitting. Do not use for lifting, supporting or transporting people or objects.
• Always sit in the center of the seat.
• Ensure the seat is fully lowered before getting on or off the stool.
• Before each use, visually inspect the stool for abnormal conditions such as cracked welds, damage, and bent, broken, loose or missing parts.
• If the stool is found to be damaged, it should be removed from service immediately until repaired by qualified service personnel.
• Do not use any attachments, adapters or accessories not supplied by the manufacturer.
• No alterations shall be made to this product.
• Use only a good grade hydraulic jack oil. Do not use brake fluid, turbine oil, transmission fluid, motor oil or glycerin.
• Failure to heed these warnings may result in personal injury and/or property damage.
How do I assemble the PRO-LIFT C-2701?
To assemble your PRO-LIFT C-2701, follow these steps:
Step 1. Attach seat post (4) to the seat (1).
Step 2. Attach seat plate (3) to the bottom of the seat post (4) with four hex bolts (2). Tighten the bolts securely.
Step 3. Insert the seat post assembly into the hydraulic base assembly (5).
How do I raise the seat on the PRO-LIFT C-2701?
To raise the seat of the PRO-LIFT C-2701, remove your weight from the seat and pull up on the control handle (6). When the desired height is reached, release the control handle.
How do I lower the seat on the PRO-LIFT C-2701?
To lower the seat of the PRO-LIFT C-2701, sit on the seat and pull up on the control handle (6). When the desired height is reached, release the control handle. A minimum of 45 lbs. is required on the seat to lower it.
How do I bleed air from the hydraulic system of my PRO-LIFT C-2701?
To bleed air from the hydraulic system of your PRO-LIFT C-2701, follow this procedure:
Step 1. Sit on the seat and pull up on the control handle (6) to fully lower the seat.
Step 2. Get off the seat and remove the seat assembly from the hydraulic base assembly (5).
Step 3. Use a flat head screwdriver to gently pry open the clip on the control handle. Remove the control handle from the release valve pin.
Step 4. Depress and hold down the release valve pin.
Step 5. While holding down the release valve pin, grasp the inner cylinder of the hydraulic base assembly and pull up to fully extend it.
Step 6. Release the release valve pin.
Step 7. Reinstall the control handle and seat assembly.
How do I add or change the hydraulic fluid in the PRO-LIFT C-2701?
To add or change the hydraulic fluid, follow these steps:
Step 1. With the seat in the fully lowered position, place the stool on its side.
Step 2. Locate and remove the oil fill plug on the side of the hydraulic base assembly (5).
Step 3. Fill with a good quality hydraulic jack oil. The hydraulic system should be completely full.
Step 4. Reinstall the oil fill plug.
Step 5. Perform the air bleeding procedure.
What routine maintenance and cleaning does the PRO-LIFT C-2701 require?
For routine maintenance of your PRO-LIFT C-2701:
Lubrication: Periodically lubricate the casters and caster swivels with a light grease.
Cleaning: Periodically clean the stool. Use a soft cloth and mild soap or detergent to clean all surfaces.
What are the technical specifications for the PRO-LIFT C-2701?
| Rated Capacity | 300 lbs |
| Minimum Height | 15-3/8 in. |
| Maximum Height | 20 in. |
| Base Diameter | 15-1/4 in. |
| Seat Diameter | 13-3/4 in. |
| Casters | 5 (2-1/2 in. dia.) |
How can I troubleshoot common issues with my PRO-LIFT C-2701?
Refer to the table below to troubleshoot common problems with your PRO-LIFT C-2701.
| Symptom | Probable Cause | Remedy |
|---|---|---|
| Stool will not lift | 1. Release valve not fully closed. 2. Air in system. |
1. Firmly push down on control handle. 2. Bleed air from hydraulic system. |
| Stool will not hold load / feels spongy | 1. Release valve not fully closed. 2. Air in system. 3. Oil level low. 4. Worn out seals. |
1. Firmly push down on control handle. 2. Bleed air from hydraulic system. 3. Check and refill. 4. Discontinue using stool and contact technical service. |
| Lifts slowly or not to full height | 1. Oil level low. 2. Air in system. |
1. Check and refill. 2. Bleed air from hydraulic system. |
| Will not lower completely | 1. Oil level too high. | 1. Drain excess fluid. |
| Seat will not lower after being raised without load | 1. Normal. Minimum of 45 lbs. required on seat to lower. | 1. Apply weight to seat. |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD PRO-LIFT C-2701 (01) PDF DOCUMENT