PINGI ID-A300 (01) PDF Document

The PINGI ID-A300 car dehumidifier is designed to effectively remove moisture from the interior of your vehicle. It operates on 100-240V, 50/60Hz mains electricity and should never be connected to other power sources. This rechargeable device gradually absorbs excess moisture in small, enclosed spaces when it is not plugged in.

Step 1. Remove the plastic wrapping from the product before the first use.

Step 2. Check the indicator pearls. If the pearls are green, the device is saturated and must be connected to mains electricity for 15 to 20 hours in a well-ventilated area.

Step 3. If the indicator pearls are orange, the device is ready for immediate use.

Step 4. Ensure all packaging materials and promotional labels or stickers are removed before operation.

The PINGI ID-A300 uses color-changing pearls to show its status:

Ready for use: The indicator pearls are orange, meaning sufficient moisture absorption capacity is available.

Saturated: During use, the pearls change from orange to green. When they are clearly green, the device is full and needs to be recharged.

Intermediate stage: If the pearls are neither orange nor green, it is an intermediate phase. You can continue using the device until the pearls become clearly green.

Step 1. Connect the supplied power cable to the socket on the back of the device.

Step 2. Insert the plug into a mains electricity power point. Recharging begins automatically.

Step 3. Always recharge the appliance in an upright position on a dry, level, and heat-resistant surface.

Step 4. Leave the device plugged in for 15 to 20 hours until the indicator pearls turn orange again.

Step 5. Do not leave the device plugged in for more than 24 hours.

Step 6. Unplug the appliance from the power point and remove the power cord. The device is now ready for use again.

The PINGI ID-A300 does not have an ON/OFF switch. It continuously absorbs moisture from its surroundings unless it is connected to mains electricity for recharging. To stop the recharging process, simply remove the plug from the mains socket.

If absorption seems low, perform the following checks:

1. Check the relative humidity in the surrounding space.

2. Check the indicator pearl color to see if recharging is required.

3. Ensure the ventilation openings in the body are not blocked.

4. Conduct a weight test: Connect the device to mains electricity for 20 hours and weigh it. Wait 7 days and weigh it again to see if there is a weight increase.

5. Note that the device is designed to absorb moisture gradually, and multiple cycles may be needed in spaces with high moisture levels.

It is normal for the device to get warm during the recharging process as it evaporates the absorbed moisture. Sometimes water may condense beneath the device during this time. For this reason, you should not recharge the device on moisture-sensitive or heat-sensitive surfaces.

The PINGI ID-A300 dehumidifier must be secured before you begin driving the vehicle. An unsecured device may slide around, potentially distracting the driver, harming passengers, or obstructing the foot pedals.

1. This appliance can be used by children aged 8 years and above if they are supervised or instructed on safe use.

2. Keep the appliance out of reach of small children, as it contains small parts that may cause choking.

3. Children under 3 years old should be kept away unless continuously supervised.

4. Avoid contact with water, oil, grease, and other liquids.

5. Plastic bags and packaging used for the device can be dangerous; keep them away from babies and children to avoid the risk of suffocation.

1. Always inspect the device for damage before use. Do not use it if it has been dropped or damaged.

2. Only use the original lead cord provided with the device.

3. Ensure your hands are dry before handling the plug or mains socket.

4. Do not immerse the cord, plug, or device in water or other liquids.

5. Place the device at least 10 cm away from other objects when plugged in to allow for sufficient ventilation.

6. Do not touch the ventilation points during or after use, as they will be hot.

7. Do not connect the appliance to an external timer or remote control system.

8. If using an extension cable, ensure its electrical rating is at least as high as the appliance.

If necessary, you can wipe the exterior of the PINGI ID-A300 with a lightly dampened cloth. The heat generated during the recharging process automatically kills bacteria absorbed in the water.

Do not dispose of the PINGI ID-A300 as unsorted municipal waste. Use separate collection facilities. Contact your local government for information regarding available collection systems. When replacing old appliances with new ones, retailers are often legally obligated to take back the old appliance for disposal at no charge.