PHILIPS LATTEGO EP5242 (01) PDF MANUAL

1. To brew a coffee, tap the drink icon of your choice or tap the ‘More Drinks’ icon.

You can now adjust the drink to your personal taste. Use the up and down arrows to adjust the coffee strength. Tap the OK icon if you want to adjust more settings.

2. Press the start/stop button at any time to start brewing the selected drink.

3. To stop dispensing coffee before the machine is finished, press the start/stop button again.

To brew 2 coffees at the same time, tap the drink icon twice or select the 2x icon scrolling the dedicated bar.

Do not use caramelized or flavored coffee beans.

LatteGo consists of a milk container, a frame and a storage lid. To avoid leakage, make sure the frame and the milk container are properly assembled before you fill the milk container.

1. To assemble LatteGo, first insert the top of the milk container under the hook at the top of the frame. Then press home the bottom part of the milk container. You hear a click when it locks into place.

Note: Make sure that the milk container and the frame are clean before you connect them.

2. Slightly tilt LatteGo and put it on the hot water spout. Then press it home until it locks into place.

3. Fill LatteGo with milk. Do not fill the milk container beyond the maximum indication.

If you have personalized the milk quantity, you may need to fill the milk container with more or less milk than indicated for this drink on LatteGo.

Always use milk coming directly from the fridge for optimal results.

4. Place a cup on the drip tray.

5. Tap the milk-based drink icon of your choice or tap the ‘More Drinks’ icon to select a different drink.

You can now adjust the drink to your own preference.

6. Press the start/stop button.

When you brew cappuccino, flat white, latte macchiato, iced cappuccino or iced latte, the machine first dispenses milk and then coffee. When you brew caffè latte, café au lait, iced caffè latte, or iced café au lait, the machine first dispenses coffee and then milk.

To stop dispensing milk before the machine has dispensed the preset amount, press the start/stop button.

7. To stop dispensing the complete drink (milk and coffee) before the machine is finished, press and hold the start/stop button.

The coffee is brewed with warm water. Brew over ice cubes for optimal results.

1. Take a glass and fill it two-thirds with ice cubes.

2. Place the glass under the coffee dispensing spout.

3. Tap the iced coffee icon.

You can now adjust the drink to your preferred taste.

We recommend using aroma strength 3.

4. Press the start/stop button.

5. To stop dispensing coffee before the machine is finished, press the start/stop button again.

6. For a special iced coffee treat, top it up with cold milk.

Your machine offers you the possibility to add an extra shot of Ristretto to your coffee and milk drinks, for example if you want to have a stronger coffee.

1. Place a cup under the spout.

2. Tap one of the one-touch drinks icons to select a drink or tap the ‘More Drinks’ icon to select a drink.

3. Use the up arrow to set the strength to the top level and then select the ExtraShot function.

4. Tap the OK icon if you want to personalize the other settings. Then press the start/stop icon to start brewing the drink.

5. To stop dispensing the drink before the machine has finished, press the start/stop icon again.

When you have selected the ExtraShot function, you can only brew one coffee at the time.

You can choose to use pre-ground coffee instead of beans, for example if you prefer a different coffee variety or decaffeinated coffee.

1. Open the lid of the pre-ground coffee compartment and pour one leveled measuring scoop of pre-ground coffee into it. Then close the lid.

2. Tap one of the one-touch drink icons or tap the ‘More Drinks’ icon to select another drink.

3. Select the pre-ground coffee function. You can do this in 2 different ways:

use the down arrow to set the strength to the lowest level and then select the pre-ground function.

press the Settings icon and use the down arrow to select the pre-ground function.

4. To stop dispensing coffee before the machine has finished, press the start/stop button again.

When you select the pre-ground coffee function:

it is automatically stored.

you can only brew one coffee at a time.

you cannot select a different aroma strength.

1. If attached, remove LatteGo.

2. Place a cup under the hot water spout.

3. Tap the ‘More Drinks’ icon and use the up and down arrows to select hot water.

4. Use the up and down arrows to adjust the hot water quantity and/or temperature to your preference.

5. Press the start/stop button.

Hot water is dispensed from the hot water spout.

6. To stop dispensing hot water before the machine is finished, press the start/stop button again.

The machine allows you to adjust the settings of a drink to your own preference and to store the adjusted drink in a personal profile. The different profiles have different colors.

After selecting a drink by tapping one of the one-touch drink icons or by tapping the ‘More Drinks’ icon, you can do the following things:

1. adjust the aroma strength with the up and down icons. There are 5 strengths, the lowest is the mildest and the highest is the strongest.

2. adjust the coffee quantity and/or the milk quantity with the up and down icons. There are 5 quantities for each of the settings.

As soon as the machine has finished brewing, the settings you selected will be stored automatically in the profile you chose.

You can select a profile and store a recipe using My coffee choice profiles (My Coffee Choice Profiles).

1. Tap the profiles icon repeatedly to select one of the colored profiles. All profiles have a different color.

2. Select a drink by tapping one of the one-touch drink icons or by tapping the ‘More Drinks’ icon.

3. Adjust the drink settings to your favorite taste.

4. Press start/stop button to brew the drink you selected.

Your new settings have now been stored in the colored profile you selected.

Your machine is equipped with a guest profile. When the guest profile is selected, the profile icon is off. When you select this profile, you can still personalize the settings to your own preference but the recipes you brew will not be stored.

1. Immerse the water hardness test strip in tap water or hold it under the tap for 1 second.

2. Wait 1 minute. The number of squares on the test strip that turn red indicate the water hardness.

1. Tap the Settings icon and use the up and down arrows to select ‘Water hardness’. Then press the OK icon to confirm.

2. Use the up and down arrows to select the water hardness level. The number of red squares selected on the display should be the same as the number of red squares on the test strip.

3. When you have set the correct water hardness, tap the OK icon to confirm.

You can change the coffee strength with the grind setting knob inside the bean container. The lower the grind setting, the finer the coffee beans are ground and the stronger the coffee. There are 12 different grind settings you can choose from.

You can only adjust the grind settings when the machine is grinding coffee beans. You need to brew 2 to 3 drinks before you can taste the full difference.

Do not turn the grind setting knob more than one notch at a time to prevent damage to the grinder.

1. Place a cup under the coffee dispensing spout.

2. Open the lid of the coffee bean hopper.

3. Tap the espresso icon and then press the start/stop button.

4. When the grinder starts grinding, press down the grind setting knob and turn it to the left or right.

By tapping the Settings icon you can adjust the following machine settings:

Water hardness: you can select between 5 levels according to the water hardness in your region;

Standby time: you can select 15, 30, 60 or 180 min

Display brightness: you can select low, medium and high.

Language

Sound: you can activate or deactivate the beeping sound of the machine

Temperature: you can choose between 3 brewing temperatures for your coffee

Front illumination (5500 series only): you can choose ‘always on’, ‘on during brewing’ or ‘always off’.

Measuring unit: you can choose between ml. or oz.

Profile activation: you can activate or deactivate profiles.

Rinsing on start-up: you can activate or deactivate an automatic rinsing cycle when you switch on the machine.

Display backlight: you can activate or deactivate the backlight in the drink buttons.

The machine offers you the possibility to restore the factory settings at any moment.

1. Tap the Settings icon.

2. Use the up and down icons to select ‘Factory settings’. Confirm by tapping the OK icon.

3. Press the start/stop button to confirm you want to restore the settings.

The settings are now being restored.

The following factory settings are restored to default: water hardness, standby time, brightness, display backlight, start-up rinsing, sound, temperature, front illumination, profiles.

1. Switch off the machine.

2. Remove the water tank and open the service door.

3. Press the PUSH handle and pull at the grip of the brew group to remove it from the machine.

Before you slide the brew group back into the machine, make sure it is in the correct position.

1. Check if the brew group is in the correct position. The arrow on the yellow cylinder on the side of the brew group has to be aligned with the black arrow and N.

If they are not aligned, push down the lever until it is in contact with the base of the brew group.

2. Slide the brew group back into the machine along the guiding rails on the sides until it locks into position with a click. Do not press the PUSH button.

3. Close the service door and place back the water tank.

1. Remove the brew group.

2. Rinse the brew group thoroughly with water. Carefully clean the upper filter of the brew group.

3. Let the brew group air-dry before you place it back. Do not dry the brew group with a cloth to prevent fibers from collecting inside the brew group.

Only use Philips coffee oil remover tablets.

1. Tap the Clean icon and use the up and down arrows to select ‘Brew group clean’.

2. Tap the OK icon to confirm and then follow the instructions on the screen.

To improve your machine’s performance, we suggest that you lubricate the brew group every 2 months, to ensure that the moving parts continue to move smoothly.

1. Apply a thin layer of grease on the piston (grey part) of the brew group.

2. Apply a thin layer of grease around the shaft (grey part) in the bottom of the brew group.

3. Apply a thin layer of grease to the guiding rails on both sides.

1. Make sure LatteGo is properly attached to the machine.

2. Place a cup under the spout.

3. Tap the Clean icon and use the up and down arrows to select the ‘Quick milk clean’ program.

4. Tap the OK icon to confirm and then follow the instructions on the screen to remove any milk that may be left inside the milk system.

Small jets of hot water will be dispensed by the milk system.

5. Store LatteGo with the remaining milk in the fridge.

1. Remove LatteGo from the machine.

2. Pour out any remaining milk.

3. Press the release button and remove the milk container from the frame of LatteGo.

4. Clean all parts in the dishwasher or under the tap with lukewarm water and some washing-up liquid.

When the AquaClean is active, the status of the AquaClean filter is always visible on the screen as a percentage.

If the status of the AquaClean filter is 10% or less, the screen shows a message for 2 seconds each time you switch on the machine. This message advises you to buy a new filter.

If the status of the filter is 0%, the machine asks you to replace the AquaClean filter every time you switch on the machine.

The machine does not automatically detect that a filter has been placed in the water tank. Therefore you need to activate each new AquaClean water filter that you install in the ‘Clean’ menu.

When the machine stops showing the filter activation message, you can still activate an AquaClean water filter, but you will need to descale the machine first.

Your machine has to be completely limescale-free before you start using the AquaClean water filter.

Before activating the AquaClean water filter, it has to be prepared by soaking it in water as described below. If you don’t do this, air might be drawn into the machine instead of water, which makes a lot of noise and prevents the machine from being able to brew coffee.

1. Tap the ‘Clean’ icon and use the up and down arrows to select ‘AquaClean’.

2. Tap the OK icon to confirm.

3. Tap the OK icon again when the activation screen appears. Follow the instructions on the screen.

4. Shake the filter for about 5 seconds.

5. Immerse the filter upside down in a jug with cold water and shake/press it.

6. Insert the filter vertically onto the filter connection in the water tank. Press it down to the lowest possible point.

7. Fill the water tank with fresh water and place it back into the machine.

8. If attached, remove the LatteGo.

9. Place a bowl under the hot water spout.

10. Press the start/stop button to start the activation process.

11. Hot water will be dispensed from the hot water spout during 1 minute.

12. The filter is now successfully activated.

After 95 liters of water have flowed through the filter, the filter will cease to work. The AquaClean status indicator drops to 0% to remind you to replace the filter. As long as the AquaClean status indicator is shown on the display, you can replace the filter without having to descale the machine first. If you do not replace the AquaClean water filter in time, the AquaClean indicator goes out after some time. In that case you can still replace the filter but you first need to descale the machine.

When the AquaClean status indicator drops to 0% or when the machine reminds you to replace the AquaClean filter:

1. take out the old AquaClean water filter.

2. install a new filter and activate it as described in chapter ‘Activating the AquaClean water filter’.

Replace the AquaClean water filter at least every 3 months, even if the machine does not yet indicate that replacement is required.

When the machine needs descaling, a message appears on the display.

1. Touch the clean icon on the user interface and select ‘Descaling’ in the menu.

2. Follow the instructions on the screen.

3. If attached, remove LatteGo.

4. Remove the drip tray and the coffee grounds container, empty them and put them back into place.

5. Remove the water tank and empty it. Then remove the AquaClean water filter.

6. Pour the whole bottle of descaler in the water tank and then fill it with water up to the Calc / Clean indication. Then place it back into the machine.

7. Place a large container (1.5 l) under the coffee dispensing spout and the water spout.

8. Press the start/stop button to start the descaling procedure. The descaling procedure lasts approximately 30 minutes and consists of a descaling cycle and a rinsing cycle.

9. Wait until the machine stops dispensing water. Refill the water tank when the message appears on the display. The descaling procedure is finished when the machine stops dispensing water.

10. Install and activate a new AquaClean water filter in the water tank.

When the descaling procedure is finished, the machine reminds you to install the new AquaClean filter.

Using the AquaClean filter reduces the need for descaling!

You can exit the descaling procedure by pressing the on/off button on the control panel. If the descaling procedure is interrupted before it is completely finished, do the following:

1. Empty and rinse the water tank thoroughly.

2. Fill the water tank with fresh water up to the Calc / Clean level indication and switch the machine back on.

3. Before brewing any drinks, perform a manual rinsing cycle. To perform a manual rinsing cycle, first dispense half a water tank of hot water by repeatedly selecting the hot water function and then brew 2 cups of pre-ground coffee without adding ground coffee.

If the descaling procedure was not completed, the machine will require another descaling procedure as soon as possible.