PHILIPS AC3059 (01) PDF Document

Danger

• Do not clean the PHILIPS AC3059 with water, any other liquid, or a (flammable) detergent, nor let them enter the appliance, to avoid electric shock and/or a fire hazard.

• Do not spray any flammable materials such as insecticides or fragrance around the appliance.

Warning

• Check if the voltage indicated on the appliance corresponds to the local power voltage before you connect the appliance.

• If the power cord is damaged, you must have it replaced by Philips, a service center authorized by Philips, or similarly qualified persons in order to avoid a hazard.

• Do not use the appliance if the plug, the power cord, or the appliance itself is damaged.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and maintenance shall not be made by children without supervision.

• Do not block the air inlet and outlet, e.g. by placing items on the air outlet or in front of the air inlet.

• Make sure that foreign objects do not fall into the appliance through the air outlet.

Caution

• This appliance is not a substitute for proper ventilation, regular vacuum cleaning, or use of an extractor hood or fan while cooking.

• Always place and use the appliance on a dry, stable, level, and horizontal surface.

• Leave at least 20cm free space around the appliance and leave at least 30cm free space above the appliance.

• Do not sit or stand on the appliance. Do not place anything on top of the appliance.

• Do not place the appliance directly below an air conditioner to prevent condensation from dripping onto the appliance.

• Only use the original Philips filters specially intended for this appliance. Do not use any other filters.

• Combustion of the filter may cause irreversible human hazard and/or jeopardize other lives. Do not use the filter as fuel or for similar purpose.

• Avoid knocking against the appliance (the air inlet and outlet in particular) with hard objects.

• Do not insert your fingers or objects into the air outlet or the air inlet to prevent physical injury or malfunctioning of the appliance.

• Do not use this appliance when you have used indoor smoke-type insect repellents or in places with oily residues, burning incense, or chemical fumes.

• Do not use the appliance near gas appliances, heating devices or fireplaces.

• Always unplug the appliance when you want to move, clean appliance, replace the filter or carry out other maintenance.

• The appliance is only intended for household use under normal operating conditions.

• Do not use the appliance in wet surroundings or in surroundings with high humidity or high ambient temperatures, such as the bathroom, toilet, or kitchen, or in a room with major temperature changes.

• The appliance does not remove carbon monoxide (CO) or radon (Rn). It cannot be used as a safety device in case of accidents with combustion processes and hazardous chemicals.

The PHILIPS AC3059 consists of the following components:

A: Control panel

B: Air outlet

C: Particle sensor

D: Gas sensor

E: NanoProtect filter Series 3 (FY3430/30)

F: Back cover

Control buttons

Display panel

Remove all packaging of the filter before first use. Make sure the air purifier is unplugged from the electrical outlet before installing the filter.

1. Pull the back cover and remove it from the appliance.

2. Pull the filter from the appliance.

3. Remove all packaging materials of the air purification filter.

4. Put the filter back into the appliance.

5. Reattach the back cover.

1. Download and install the Philips ‘Clean Home+’ app from the App Store or Google Play.

2. Put the plug of the air purifier in the power socket and touch the power button to turn on the air purifier. The Wi-Fi indicator will blink orange for the first time.

3. Make sure that your smartphone or tablet is successfully connected to your Wi-Fi network.

4. Launch the “Clean Home+” app and click on “Connect a New Device” or press the “+” button on the top of the screen. Follow the onscreen instructions to connect the air purifier to your network.

Note:

• If you want to connect more than one air purifier to your smartphone or tablet, you have to do this one by one.

• Make sure that the distance between your smartphone or tablet and the air purifier is less than 10 m without any obstructions.

Reset the Wi-Fi connection when your default network has changed.

1. Put the plug of the air purifier in the power socket and touch the power button to turn on the air purifier.

2. Touch the light on/off button and display switch button simultaneously for 3 seconds until you hear a beep. The air purifier goes to pairing mode, and the Wi-Fi indicator blinks orange.

3. Follow the steps 3-4 in “Setting up the Wi-Fi connection for the first time”.

The air quality light automatically turns on when the PHILIPS AC3059 is switched on and cycles through all colors. After about 30 seconds, the particle sensor selects the color corresponding to the surrounding air quality. The color is determined by the highest risk index among PM2.5, IAI, and Gas readings.

IAI (Indoor Allergen Index)

The AeraSense sensor detects indoor air allergen levels. A numerical feedback from 1 to 12 displays the potential risk, where 1 indicates the best air quality.

PM2.5

AeraSense technology detects and responds to airborne particle pollutants smaller than 2.5 micrometers, providing real-time PM2.5 feedback.

GAS

An advanced gas sensor displays a level from L1 to L4, indicating changes in potential harmful gases (like VOCs, odors). L1 indicates the best air quality.

Note:

• For optimum purification performance, close doors and windows.

• Keep curtains away from the air inlet or air outlet.

1. Put the plug of the air purifier in the power socket.

2. Touch the power button to switch on the air purifier.

» The air purifier beeps.

» The “—” symbol displays on the screen during warming up. Then the air purifier shows the IAI/PM2.5/Gas level after measuring the air quality.

» The air purifier operates in the auto mode with PM2.5 displayed on the screen.

3. Touch and hold the power button for 3 seconds to switch off the air purifier.

Note: If the air purifier stays connected to the electrical outlet after turning OFF, it will operate under the previous settings when turned ON again.

You can choose Auto mode, Turbo mode, or Sleep mode by touching the mode switch button.

Auto mode: The dual-sensor senses the air quality in real-time and the appliance automatically adjusts the fan speed. The control panel can also automatically adjust display screen brightness according to the ambient light.

Turbo mode: The air purifier operates at the highest speed.

Sleep mode: The air purifier operates quietly at a low speed. After 3 seconds, the screen dims.

The appliance displays the PM2.5 level by default.

• Touch the display switch button to switch the display indicator among Gas/PM2.5/IAI.

With the light sensor, the control panel can automatically turn on, turn off, or dim according to the ambient light. When the ambient light is dark, the control panel will be off or dim. You can touch any button to wake up all lights. If there is no further operation, all lights will turn off or dim again to match the ambient light.

You can touch the light on/off button manually to turn off all lights and the control panel. Touch any button to wake up all lights.

Touch the filter status check/reset button to check the filter service life status. The percentage of remaining service life of the filter displays on the screen. The appliance goes back to normal display if no operations after 3 seconds.

Regularly clean the inside and outside of the air purifier to prevent dust from collecting.

1. Use a soft, dry cloth to clean both the interior and exterior of the air purifier.

2. The air outlet can also be cleaned with a dry, soft cloth.

Clean the particle sensor every 2 months for optimal functioning of the appliance.

Note:

• If the air purifier is used in a dusty environment, it may need to be cleaned more often.

• If the humidity level in the room is very high, condensation may develop on the particle sensor and the air quality light may indicate a poorer air quality even though the air quality is actually good. If this occurs, clean the particle sensor.

1. Switch off the air purifier and unplug from the power socket.

2. Pull the back cover and remove it from the appliance.

3. Clean the particle sensor with a damp cotton swab.

4. Dry all parts thoroughly with a dry cotton swab.

5. Reattach the back cover.

When the filter cleaning alert displays on the screen, clean the surface of the filter with a vacuum cleaner.

1. Switch off the air purifier and unplug from the power socket.

2. Pull the back cover and remove it from the appliance.

3. Pull the filter from the appliance.

4. Clean the surface of the filter with a vacuum cleaner.

5. Put the filter back into the appliance.

6. Reattach the back cover.

7. Put the plug of the air purifier in the power socket.

8. Touch the power button to switch on the appliance.

9. Touch and hold the filter status check/reset button for 3 seconds to reset the filter cleaning time.

10. Wash your hands thoroughly after cleaning the filter.

This air purifier is equipped with a filter replacement indicator. When the filter needs to be replaced, the filter replacement alert lights up red. If the filter is not replaced in time, the air purifier will stop operating and lock to protect the air quality.

Note:

• The filter is not washable or reusable.

• Always turn off the air purifier and unplug from the electrical outlet before replacing the filter.

1. Switch off the air purifier and unplug from the power socket.

2. Pull the back cover and remove it from the appliance.

3. Pull the filter from the appliance.

4. Remove all packaging materials of the new filter.

5. Put the new filter into the appliance.

6. Reattach the back cover.

7. Put the plug of the air purifier in the power socket.

8. Touch the power button to switch on the appliance.

9. Touch and hold the filter status check/reset button for 3 seconds to reset the filter lifetime counter.

10. Wash your hands thoroughly after replacing the filter.

Note: Do not smell the filter as it has collected pollutants from the air.

You can replace the filter even before the filter replacement alert displays on the screen. After replacing a filter, you need to reset the filter lifetime counter manually.

1. Touch the power button for 3 seconds to turn off the appliance and unplug from the power socket.

2. Put the power plug in the power socket.

3. Within 15 seconds after power on, touch and hold the filter status/reset button and the light on/off button for 3 seconds to reset the filter lifetime counter.

1. Turn off the air purifier and unplug from the power socket.

2. Clean the air purifier, particle sensor and the surface of the filter (see chapter “Cleaning and maintenance”).

3. Let all parts air dry thoroughly before storing.

4. Wrap the filter in air tight plastic bags.

5. Store the air purifier and filter in a cool, dry location.

6. Always thoroughly wash hands after handling the filter.

• Check if the back cover is properly installed.

• The filter replacement alert has been on continuously but you have not replaced the corresponding filter. As a result, the appliance is now locked. In this case, replace the filter and long press the filter status/reset button to reset the filter lifetime counter.

The surface of the filter is dirty. Clean the surface of the filter (see the chapter “Cleaning and maintenance”).

• Check if the packing material is removed from the filter.

• The filter has not been placed in the appliance. Make sure that the filter (FY3430/30) is properly installed.

• The particle sensor is wet. The humidity level in your room is high and causes condensation. Make sure that the particle sensor is clean and dry (see the chapter “Cleaning and maintenance”).

• Room size is large or the outdoor air quality is poor. For optimum purification performance, please close the doors and windows when operating the air purifier.

• There are indoor pollution resources. For instances, smoking, cooking, incense, perfume or alcohol.

• Filter reaches the end of life. Replace the filter with a new one.

The particle sensor is dirty. Clean the particle sensor (see the chapter “Cleaning and maintenance”).

• The first few times you use the appliance, it may produce a plastic smell. This is normal. However, if the appliance produces a burnt smell even if removing filters, contact your Philips dealer or an authorized Philips service center. The filter may produce a smell after being used for a while because of the absorption of indoor gases. It’s recommended that you reactivate the filter by putting it in direct sunlight for repeated use. If the odor still exists, replace the filter.

• It’s normal if the appliance runs in Turbo mode.

• In Auto mode, if the appliance is too loud, maybe the appliance is running at high speed because air quality has become worse, or your personalized setting in the App triggers a higher fan speed. You can choose Sleep mode or change the settings in the App.

• If anything drops into the air outlet, it may also cause an abnormal loud sound. Immediately turn off the appliance, turn it upside down to get foreign objects out.

Perhaps you did not reset the filter lifetime counter. Switch on the appliance. Then touch and hold the reset button for 3 seconds.

The motor has malfunctions. Contact the Consumer Care Center in your country.

• If the router your purifier is connected to is dual-band and currently it is not connecting to a 2.4GHz network, please switch to another band of the same router (2.4GHz) and try to pair your purifier again. 5GHz networks are not supported.

• Web authentication networks are not supported.

• Check if the purifier is within range of the Wi-Fi router. You can try to locate the air purifier closer to the Wi-Fi router.

• Check if the network name is correct. The network name is case-sensitive.

• Check if the Wi-Fi password is correct. The password is case-sensitive.

• Retry the setup with the instructions in the section “Reset the Wi-Fi connection”.

• The Wi-Fi connectivity can be interrupted by electromagnetic or other interferences. Keep the appliance away from other electronic devices that may cause interference.

• Check if the mobile device is in airplane mode. Make sure to have the airplane mode deactivated when connecting to the Wi-Fi network.

• Consult the help section in the App for extensive and up-to-date troubleshooting tips.