PHILIPS 192EL2 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD PHILIPS 192EL2 (01) PDF MANUAL


PDF Content Summary: 192EL2 192E2 philips.com/welcome EN User manual 1 Customer care and warranty 29 Troubleshooting & FAQs 41 Table of Contents 1. Important ......................................................... 1 1.1 Safety precautions and maintenance ............... 1 1.2 Notational Descriptions ......................................... 2 1.3 Disposal of product and packing material....3 2. Setting up the monitor .................................. 4 2.1 Installation .......................................................................4 2.2 Operating the monitor ........................................... 5 2.3 Remove Base Stand and Base .............................7 3. Product information ...................................... 9 3.1 SmartImage Lite .......................................................... 9 3.2 SmartContrast .............................................................10 3.3 Philips SmartControl Lite ...................................... 11 3.4 Philips' Flat Panel Monitors Pixel Defect Policy ..................................................................................17 4 Technical Specifications ................................. 19 4.1 Resolution & Preset Modes.................................. 22 4.2 Automatic PowerSaving .......................................... 22 5 Regulatory Information ................................. 23 6 Customer care and warranty ...................... 29 7 Troubleshooting & FAQs .............................. 41 7.1 Troubleshooting .......................................................... 41 7.2 SmartControl Lite FAQs ........................................ 43 7.3 General FAQs .............................................................. 44

1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor. The Philips guarantee applies provided the product is handled properly for its intended use, in accordance with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase, dealer’s name and model and production number of the product. 1.1 Safety precautions and maintenance Warnings Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your computer monitor. Operation Keep the monitor out of direct sunlight and • away from stoves or any other heat source. Remove any object that could fall into • ventilation holes or prevent proper cooling of the monitor’s electronics. Do not block the ventilation holes on the • cabinet. When positioning the monitor, make sure the • power plug and outlet are easily accessible. If turning off the monitor by detaching the • power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation. Please use approved power cord provided • by Philips all the time. If your power cord is missing, please contact with your local service center. (Please refer to Customer Care Consumer Information Center) 1 Do not subject the monitor to severe • vibration or high impact conditions during operation. Do not knock or drop the monitor during • operation or transportation. Maintenance To protect your monitor from possible • damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD panel. Unplug the monitor if you are not going to • use it for an extensive period of time. Unplug the monitor if you need to clean it • with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your monitor. To avoid the risk of shock or permanent • damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. If your monitor gets wet, wipe it with dry cloth • as soon as possible. If foreign substance or water gets in your • monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center. Do not store or use the monitor in locations • exposed to heat, direct sunlight or extreme cold. In order to maintain the best performance of • your monitor and use it for a longer lifetime, please use the monitor in a location that falls within the following temperature and humidity ranges. o Temperature: 0-40°C 32-95°F o Humidity: 20-80% RH IMPORTANT: Always activate a moving screen • saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your monitor will display unchanging static content. Uninterrupted display of still or static images over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off. Warning Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Service The casing cover should be opened only by • qualified service personnel. If there is any need for any document for • repair or integration, please contact with your local service center. (please refer to the chapter of "Consumer Information Center") For transportation information, please refer to • "Technical Specifications". Do not leave your monitor in a car/trunk • under direct sun light. Note Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to take when the operating instructions given in this manual have been followed. 2 1.2 Notational Descriptions The following subsections describe notational conventions used in this document. Notes, Cautions and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings. They are used as follows: Note This icon indicates important information and tips that help you make better use of your computer system. Caution This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. Warning This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific presentation of the warning is mandated by the relevant regulatory authority. 1.3 Disposal of product and packing material Waste Electrical and Electronic Equipment- WEEE This marking on the product or on its packaging illustrates that, under European Directive 2002/96/ EC governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product. Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into mono materials. Please find out about the local regulations on how to dispose of your old monitor and packing from your sales representative. 3 Recycling Information for Customers There is currently a system of recycling up and running in the European countries, such as The Netherlands, Belgium, Norway, Sweden and Denmark. In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to follow the IT product recycling management process, detail can be found in web site epa.gov.tw The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is recycled at the end of its life cycle. For help and service, please contact Consumers Information Center or F1rst Choice Contact Information Center in each country.

2. Hold the monitor base stand with both hands 2. Setting up the monitor and firmly insert the base stand into the base column. 2.1 Installation Package contents 192E2/192EL2 Monitor Quick start guide Base stand EDFU CD Power cord VGA signal cable (optional) DVI cable (optional) Install base stand 1. Place the monitor face down a smooth surface taking care to avoid scratching or damaging the screen. Then lift the monitor stand. CLICK! © 2010 Koninklijke 5B Philips Electronics, N.V.All rights reserved. Unauthorized duplication is a violation of applicable laws. Made and printed in China. Version M22260.0V5B1.001 Philips Koninklijke and Philips the Philips’ Electronics Shield Emblem N.V. and are are registered used under trademarks license from of Koninklijke Philips Electronics N.V. 4 Connecting to your PC Kensington anti-thief lock AC power input DVI-D input (available for selecting model) VGA input Connect to PC 1. Connect the power cord to the back of the montior firmly. 2. Turn off your computer and unplug its power cable. 3. Connect the monitor signal cable to the video connector on the back of your computer. 4. Plug the power cord of your computer and your monitor into a nearby outlet. 5. Turn on your computer and monitor. If the monitor displays an image, installation is complete. 5 2.2 Operating the monitor Front view product description : To access OSD menu. : Return to previous OSD level. : Change to 4:3 display. : To switch monitor’s power on and off. : To adjust the OSD menu. : To change the signal input. : SmartImage Lite. There are 3 modes to be selected: Standard, Internet and Game. Description of the On Screen Display What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below: Basic and simple instruction on the control keys In the OSD shown above users can press buttons at the front bezel of the monitor to move the cursor, OK to confirm the choice or change. 6 The OSD Menu Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. Main menu Auto Sub menu Sub menu Input VGA DVI (available for selective models) Language English㕜Español, Français, Deutsch, Italiano, OSD Setting Horizontal 0~100 0~100 Vertical 0~100 0~100 Transparency Off, 1, 2, 3, 4 Off, 1, 2, 3, 4 Picture Picture Format Wide screen,4:3 Brightness 0~100 Contrast 0~100 SmartContrast On, Off Color Color Temp. 6500K, 9300K sRGB User Define Red: 0~100 Green: 0~100

Blue: 0~100 Português, Русский㕜 簡体中文,Türkçe

OSD Time out 5, 10, 20, 30, 60 Setup H. Position 0~100 V. Position Phase Clock 0~100 0~100 0~100 Resolution Notification On, Off Reset Yes, No Information

Resolution notification 2.3 Remove Base Stand and Base This monitor is designed for optimal performance at its native resolution, 1366x768@60Hz. Remove the Base Stand When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1366x768@60Hz for best results. Display of the native resolution alert can be Before you start disassembling the monitor base, please follow the instructions below to avoid damage or injury. switched off from Setup in the OSD (On Screen Display) menu. 1. Place the monitor face down on a smooth surface, taking care to avoid scratching or damaging the screen. Physical Function Tilt 2. Press the locking clips to detach the base stand away from the base column. 7 Remove the Base Condition: For VESA standard mounting applications •1. Remove the 4 screw covers. 2. Remove the 4 screws and then remove the base from the monitor. 8 Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. 100mm 100mm

3. Product information How to enable SmartImage Lite? 3.1 SmartImage Lite What is it? SmartImage Lite provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage Lite delivers great optimized monitor performance. 1. Press to Why do I need it? You want a monitor that delivers optimized display all your favorite types of content, SmartImage Lite software dynamically adjust brightness, contrast, color and sharpness in real time to enhance your monitor viewing experience. How does it work? SmartImage Lite is an exclusive, leading edge Philips technology that analyzes the content displayed on your screen. Based on a scenario you select, SmartImage Lite dynamically enhances the contrast, color saturation and sharpness of images to enhance the contents being displayed - all in real time with the press of a single button. 9 launch the SmartImage Lite on screen display; 2. Keep pressing to toggle between Standard, Internet, and Game. 3. The SmartImage Lite on screen display will remain on screen for 5 seconds or you can also press”OK” to make confirmation. 4. When SmartImage Lite is enabled, the sRGB scheme is disabled automatically. To use sRGB you need to disable SmartImage Lite with the button at the front bezel of your monitor. Except using key to scroll down, you can also press buttons to choose and press “OK” to confirm selection and close the SmartImage Lite OSD. There are 3 modes to be selected: Standard, Internet, and Game. Standard: • Enhances text and dampens brightness to increase readability and reduce eye strain. This mode significantly enhances readability and productivity when you're working with spreadsheets, PDF files, scanned articles or other general office applications. Internet: • This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors. • Game: Turn on over drive circuit for best response time, reduce jaggy edges for fast moving objects on screen, enhance contrast ratio for bright and dark scheme, this profile delivers the best gaming experience for gamers. 10 3.2 SmartContrast What is it? Why do I need it? You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically controls contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text for office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of your monitor. How does it work? When you activate SmartContrast, it will analyse the content you are displaying in real time to adjust colors and control backlight intensity. This function will dynamically enhance contrast for a great entertainment experience when viewing videos or playing games.

Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds.

3.3 Philips SmartControl Lite The new SmartControl Lite software by Phillips allows you to control your monitor via an easy to use on-screen graphic interface. Complicated adjustments are a thing of the past as this user friendly software guides you through fine-tuning resolution, Color calibration, Clock/Phase adjustments, RGB White point adjustment, etc. Equipped with latest technology in core algorithm for fast processing and response, this Windows 7 compliant eye catching animated Icon based software is ready to enhance your experience with Philips monitors! Installation Follow the instruction and complete the • installation. You can launch after installation is completed. • If you want to launch later, you can either click • the shortcut on desktop or toolbar. 11 First launch -Wizard The first time after installation of SmartControl • Lite, it will automatically go to Wizard for first time launch. The wizard will guide you through adjustment • your monitor performance step by step. You can go to Plug-in menu to launch wizard • later on as well. You can adjust more options without wizard • by Standard pane.

Start with Standard pane: Adjust menu: Adjust Menu allow you to adjust Brightness, • Contrast, Focus, Position and Resolution. You can follow the instruction and do the • adjustment. Cancel prompts user if you want to cancel • installation. 12 Color menu: Color Menu allow you to adjust RGB, Black • Level, White Point, Color Calibration, and SmartImage Lite (Please refer to SmartImage Lite section). You can follow the instruction and do the • adjustment. Refer to below table for sub-menu item base • on your input. Example for Color Calibration • 1. "Show Me" starts color calibration tutorial. 2. Start - starts the 6-step color calibration sequence. 3. Quick View loads the before/after images. 4. To return to Color home pane, click the Cancel button. 5. Enable color calibration - by default is on. If unchecked, does not allow for color calibration to happen, dimes out start and quick view buttons. 6. Must have patent info in calibration screen. 13

• Previous button is disabled until the second color screen. Next goes to the succeeding target (6-targets). • Final next goes File>Presets pane. • • Cancel closes the UI and returns to the plug in page. SmartImage Lite Allows user to change setting for better display setting based on content. When Entertainment is set, SmartContrast and SmartResponse are enabled. First color Calibration Screen: Options>Preferences - Will only be active when selecting Preferences from the drop-down Options menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available. 14 Displays current preference settings. • A checked box enables the feature. The check • box is a toggle. Enable Context Menu on desktop is checked • (On) by default. Enable Context menu displays SmartControl Lite selections for Select Preset and Tune Display in the desktop right-click context menu. Disabled removes SmartControl Lite from the right click context menu. Enable Task Tray icon is checked (On) by • default. Enable context menu shows the task tray menu for SmartControl Lite. A right click on the task tray icon displays the menu options for Help, Technical Support. Check for Upgrade, About, and Exit. When Enable task tray menu is disabled, the task tray icon will only display EXIT. Run at Startup is checked (On) by default. • When disabled, SmartControl Lite will not launch at start or be in the task tray. The only way to launch SmartControl Lite is either from the desktop short cut or from the program file. Any preset set to run at startup will not load when this box is unchecked (Disabled). Enable transparency mode (Windows 7, Vista, • XP). Default is 0% Opaque. Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available. All other SmartControl Lite tabs are not available. • Display the Source instruction pane and current input source setting. • On single input displays, this pane will not be visible. Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available. 15 Help>Version - Will only be active when selecting Version from the drop- down Help menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available. Context Sensitive menu The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the Options>Preferences pane, then the menu will be visible. The Context Menu has four entries: SmartControl • Lite - When selected the About

Screen is displayed. Select Preset - Provides a hierarchical menu • of saved presets for immediate use. A check mark shows the currently selected preset. Facoty Preset can also be called from the drop down menu. Tune Display - Opens the SmartControl • Lite control panel. SmartImage Lite - • Check current settings, Standard, Internet, Game.

The task tray has five entries: • Help - Access to User Manual file: Open User Manual file using the default browser window. Technical Support - displays the tech • support page. Check for Update - takes the user to PDI • Landing and checks the user's version against the most current available. About - Displays detailed reference • information: product version, release information, and product name. Exit - Close SmartControl • Lite To run SmartControl Lite again either select SmartControl Lite from Program menu, double-click the desktop PC icon or restart the system. Task Tray Menu Enabled The task tray menu can be displayed by right- clicking on the SmartControl Lite icon from the task tray. Left Click will launch the application. 16 Task Tray Menu Disabled When the Task Tray is disabled in the preference folder, only the EXIT selection is available. To completely remove SmartControl Lite from the task tray, disable Run at Startup in Options>Preferences. 3.4 Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19" XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain types or combinations of pixel defects that are more noticeable than others. This policy is valid worldwide. Pixels and Sub pixels A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 17 Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are the types of bright dot defects: One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Three adjacent lit sub pixels (one white pixel) Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots. Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern. These are the types of black dot defects. Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.

BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL 192E2/192EL2 1 lit subpixel 3 2 adjacent lit subpixels 1 3 adjacent lit subpixels (one white pixel) 0 Distance between two bright dot defects* >15mm Total bright dot defects of all types 3 BLACK DOT DEFECTS ACCEPTABLE LEVEL MODEL 192E2/192EL2 1 dark subpixel 5 or fewer 2 adjacent dark subpixels 2 or fewer 3 adjacent dark subpixels 0 Distance between two black dot defects* >15mm Total black dot defects of all types 5 or fewer TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL 192E2/192EL2 Total bright or black dot defects of all types 5 or fewer Note 1 or 2 adjacent sub pixel defects = 1 dot defect This monitor is ISO9241-307 compliant. 18 4 Technical Specifications Picture/Display LCD panel type TFT-LCD Backlight CCFL (192E2), LED (192EL2) Panel size 18.5'' W (47.0 cm) Aspect ratio 16:9 Pixel Pitch 0.300 x 0.300 mm Brightness 250 cd/m2 SmartContrast 500,000:1 (192E2); 20,000,000:1 (192EL2) Contrast ratio (typical) 1000:1 Response time (typical) 5 ms Optimum Resolution 1366 x 768 @ 60Hz Viewing angle 176° (H) / 170° (V) @ C/R > 5 Picture Enhancement SmartImage Lite Display colors 16.7 M Vertical refresh rate 56Hz -76Hz Horizontal Frequency 30kHz - 83kHz sRGB YES Connectivity Signal input DVI-D (digital, HDCP), VGA (Analog) Input Signal Separate Sync, Sync on Green Convenience User Convenience OSD Languages English, French, German, Italian, Russian, Spanish, Simplified Chinese, Portuguese, Turkish Other convenience VESA mount (100 x 100mm), Kensington lock Plug & Play Compatibility DDC/CI, sRGB, Windows 7/Vista/XP, Mac OSX, Linux Stand Tilt -5/+20 19 Power (192E2) On mode (typical) 18.2W Energy Consumption (EnergyStar 5.0 test method) AC Input Voltage at AC Input Voltage at 100VAC +/-5VAC, 230VAC +/-5VAC, 50Hz +/- 3Hz 50Hz +/ -3Hz Normal Operation (typical) 15.38W 15.28W 15.33W Sleep (typical) 0.5W 0.5W 0.5W Off 0.5W 0.5W 0.5W Heat Dissipation* AC Input Voltage at 100VAC +/-5VAC, 50Hz +/ -3Hz AC Input Voltage at 230VAC +/-5VAC, 50Hz +/ -3Hz Normal Operation 52.49BTU 52.15BTU 52.32BTU Sleep (typical) 1.706BTU 1.706BTU 1.706BTU Off 1.706BTU 1.706BTU 1.706BTU Power (192EL2) On mode (typical) 13.5W Energy Consumption (EnergyStar 5.0 test method) AC Input Voltage at 115VAC +/-5VAC, 60Hz +/ -3Hz AC Input Voltage at AC Input Voltage at AC Input Voltage at 100VAC +/-5VAC, 115VAC +/-5VAC, 230VAC +/-5VAC, 50Hz +/- 3Hz 60Hz +/- 3Hz 50Hz +/ -3Hz Normal Operation (typical) 12.28W 12.23W 12.23W Sleep (typical) 0.5W 0.5W 0.5W Off 0.5W 0.5W 0.5W Heat Dissipation* AC Input Voltage at AC Input Voltage at 100VAC +/-5VAC, 230VAC +/-5VAC, 50Hz +/ -3Hz 50Hz +/ -3Hz Normal Operation 41.91BTU 41.74BTU 41.74BTU Sleep (typical) 1.706BTU 1.706BTU 1.706BTU Off 1.706BTU 1.706BTU 1.706BTU Power LED indicator On mode: White, Standby/Sleep mode: White (blinking) Power Supply Build-in, 100-240VAC, 50/60Hz Dimension Product with stand (WxHxD) 457 x 363 x 180mm Product without stand (WxHxD) AC Input Voltage at 115VAC +/-5VAC, 60Hz +/ -3Hz 457 x 293 x 49mm Box dimension (WxHxD) 503 x 416 x 141mm Weight Product with stand 3.4kg Product without stand 3.1kg Product with packaging 4.4kg 20 AC Input Voltage at 115VAC +/-5VAC, 60Hz +/- 3Hz Operating Condition Temperature range Storage: -20°C to 60°C operation: 0°C to 40 °C Relative humidity 20% to 80% Altitude Non-operation: + 40,000 ft ( 12,192 m) operation: + 12,000 ft ( 3,658 m) MTBF 50,000 hrs (192E2), 30,000 hrs (192EL2) Environmental ROHS YES EPEAT Silver ( epeat.net) Packaging 100% recyclable Compliance and standards Regulatory Approvals CE Mark, Energy Star 5.0, FCC Class B, SEMKO, TCO5.0, UL/cUL, ISO9241-307 Cabinet Color Black/Black Finish Glossy Note This data is subject to change without notice. Go to philips.com/support to download the latest version of leaflet. 21 4.1 Resolution & Preset Modes 4.2 Automatic PowerSaving Maximum Resolution If you have VESA DPM compliance display card For 192E2/192EL2 1366 x 768 at 60 Hz (analog input) 1366 x 768 at 60 Hz (digital input) or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will Recommended Resolution 'wake up' automatically. The following table shows the power consumption and signaling of this For 192E2/192EL2 automatic power saving feature: 1366 x 768 at 60 Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720x400 70.09 31.47 640x480 59.94 37.50 640x480 75.00 37.88 800x600 60.32 46.88 800x600 75.00 48.36 1024x768 60.00 60.02 1024x768 75.03 63.89 1280x1024 60.02 79.98 1280x1024 75.03 47.71 1366x768 59.79 Power Management Definition VESA Mode Video H-sync V-sync Power Used LED color Active ON Yes Yes 192E2< 18.2W (typ.) 192EL2< 13.5W (typ.) White Sleep OFF No No < 0.5 W (typ.) White (Blinking) Switch Off OFF - - < 0.5 W (typ.) OFF The following setup is used to measure power consumption on this monitor. Native resolution: 1366 x 768. Contrast: 50% Brightness: 250 nits Color temperature: 6500k Note This data is subject to change without notice. 22

5 Regulatory Information Lead-free Product Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic equipment. Toxic substances like Lead has been eliminated and compliance with European community’s stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life cycle. TCO Displays 5.0 Information Congratulations, Your display is designed for both you and the planet! This display carries the TCO Certified label. This ensures that the display is designed for minimal impact on the climate and natural environment, while offering all the performance expected from top of the line electronic products. TCO Certified is a third party verified program, where every product model is tested by an accredited independent test laboratory. TCO Certified represents one of the toughest certifications for displays worldwide. Some of the Usability features of the TCO Displays 5.0 requirements: Visual Ergonomics Good visual ergonomics in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are: Light levels without color tint, Uniform color • and luminance, Wide color gamut 23 Calibrated color temperature and gamma curve • Wide luminance level, Dark black levels, Low • motion blur Electrical Safety Product fulfills rigorous safety standards • Emissions Low alternating electric and magnetic fields • emissions Low acoustic noise emissions • Some of the Environmental features of the TCO • Displays 5.0 requirements: The brand owner demonstrates corporate • social responsibility and has a certified environmental management system (EMAS or ISO 14001) Very low energy consumption both in on- and • standby mode Restrictions on chlorinated and brominated • flame retardants, plasticizer and polymers Restrictions on heavy metals such as cadmium, • mercury and lead (RoHS compliance) EPEAT ( epeat.net) “The EPEAT (Electronic Product Environmental Assessment Tool) program evaluates computer desktops, laptops, and monitors based on 51 environmental criteria developed through an extensive stakeholder consensus process supported by US EPA. EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers to secure market recognition for efforts to reduce the environmental impact of its products.”

Benefits of EPEAT Reduce use of primary materials Reduce use of toxic materials Avoid the disposal of hazardous waste EPEAT’S requirement that all registered products meet ENERGY STAR’s energy efficiency specifications, means that these products will consume less energy throughout their life. CE Declaration of Conformity This product is in conformity with the following standards EN60950-1:2006 (Safety requirement of • Information Technology Equipment) EN55022:2006 (Radio Disturbance • requirement of Information Technology Equipment) EN55024:1998+A1:2001+A2:2003 (Immunity • requirement of Information Technology Equipment) EN61000-3-2:2006 (Limits for Harmonic • Current Emission) EN61000-3-3:1995+A1:2001+A2:2005 • (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable 2006/95/EC (Low Voltage Directive) • 2004/108/EC (EMC Directive) • 2005/32/EC (EuP Directive, EC No. 1275/2008 • mplementing Directive for Standby and Off mode power consumption) and is produced by a manufacturing organization on ISO9000 level. The product also comply with the following standards ISO9241-307:2008 (Ergonomic requirement, • Analysis and compliance test methods for electronic visual displays) GS EK1-2000:2009 (GS mark requirement) • prEN50279:1998 (Low Frequency Electric and • Magnetic fields for Visual Display) MPR-II (MPR:1990:8/1990:10 Low Frequency • Electric and Magnetic fields) TCO Displays 5.0 (Requirement for • Environment Labeling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions 24 Energy Star Declaration ( energystar.gov) This monitor is equipped with a function for saving energy which supports the VESA Display Power Management (DPM) standard. This means that the monitor must be connected to a computer which supports VESA DPM. Time settings are adjusted from the system unit by software. VESA State LED Indicator Power Consumption Normal ON (Active) White 192E2< 15 W (typ.) operation 192EL2< 12 W (typ.) Power Saving Alternative 2 One step Sleep (typ.) Switch Off White Blinking Off < 0.5 W (typ.) < 0.5 W (typ.) As an ENERGY STAR® Partner, we have determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Note We recommend you switch off the monitor when it is not in use for a long time. Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. • Increase the separation between the • equipment and receiver. Connect the equipment into an outlet on • a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ • TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS. 25 FCC Declaration of Conformity Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Commission Federale de la Communication (FCC Declaration) Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes: Réorienter ou déplacer l'antenne de réception. • Augmenter la distance entre l'équipement et • le récepteur. Brancher l'équipement sur un autre circuit que • celui utilisé par le récepteur. Demander l'aide du marchand ou d'un •technicien chevronné en radio/télévision. Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement. N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques. CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA. 26 EN 55022 Compliance (Czech Republic Only) Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three- prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible. A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251. BSMI Notice (Taiwan Only) 27 North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ. Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind. Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß 1. Reparaturen nur durch Fachpersonal durchgeführt werden. 2. nur original-Ersatzteile verwendet werden. 3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird. Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger. ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND. 28 China RoHS The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by Electronic Information Products" or commonly referred to as China RoHS. All products including CRT and LCD monitor which are produced and sold for China market have to meet China RoHS request. 环保使用期限 此标识指期限(十年),电子信息产品中含有的 有毒有害物质或元素在正常使用的条件下不 会发生外泄或突变, 电子信息产品用户使用该 电子信息产品不会对环境造成严重污染或对 其人身、 财产造成严重损害的期限. 6 Customer care and warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE Austria / Belgium / Denmark / France / Germany / Greece / Finland / Ireland / Italy / Luxembourg / the Netherlands / Norway / Portugal / Sweden / Switzerland / Spain / United Kingdom / Poland EASTERN EUROPE Czech Republic / Hungary / Russia / Slovakia / Slovenia / Turkey LATIN AMERICA Argentina / Brasil NORTH AMERICA Canada / USA PACIFIC Australia / New Zealand ASIA China / Hong Kong / India / Indonesia / Korea / Malaysia / Pakistan / Philippines / Singapore / Taiwan / Thailand / Vietnam AFRICA South Africa MIDDLE EAST United Arab Emirates 29 Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. What is covered? The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark, France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the Netherlands, Norway, Poland, Portugal, Sweden, Switzerland, Spain and the United Kingdom and only for monitors originally designed, manufactured, approved and/or authorized for usage within these countries. Warranty coverage begins as from the day you buy your monitor. For two years thereafter, your monitor will be swapped by at least an equivalent monitor in case of defects provided for under the warranty coverage. The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap monitor the warranty period remains equal to that of your original monitor, being 24 months as from the purchase date of your original monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This two-year service warranty entitles you to a swap model on-site if your monitor turns out to be faulty or defective. Philips aims at a swap within 48 hours of your call being received. What is excluded? The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended use, in accordance with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase, dealer's name and model and production number of the product. The Philips F1rst Choice Warranty may not apply if: The documents have been altered in any way • or made illegible; The model or production number on the • product has been altered, deleted, removed or made illegible; Repairs or product modifications and • alterations have been executed by unauthorized service organizations or persons; Damage is caused by accidents including but • not limited to lightning, water or fire, misuse or neglect; Reception problems caused by signal • conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the • monitor; Product requires modification or adaptation • to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country. Note that products that are not originally • designed, manufactured, approved and/or authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips F1rst Choice Warranty. In these cases the Philips global warranty terms are valid. 30 Just a click away In case of any problems, we advise you to read the operating instructions carefully or go to the philips.com/support website for additional support. Just a phone call away In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully or go to the philips.com/support website for additional support before contacting the Philips helpdesk. To solve your problem quickly, please prepare the following details before contacting the Philips helpdesk: Philips type number • Philips serial number • Purchase date (copy of purchase may be • required) PC environment Processor: • o CUP and Graphic card name and driver version o Operating system o Application being used Other cards installed •Having the following information available will also help speed up the process: Your proof of purchase indicating: date of • purchase, dealer name, model and product serial number. The full address to which the faulty monitor • has to be collected and the swap model should be delivered. Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact Information. Or you can reach us via: Website: philips.com/support

F1rst Choice Contact Information Country Code Telephone number Tariff Austria +43 0810 000206 €0.07 Belgium +32 078 250851 €0.06 Denmark +45 3525 8761 Local call tariff Finland +358 840 320 041 €0.08 Luxembourg +352 26 84 30 00 Local call tariff The Netherlands +31 0900 0400 063 €0.10 Norway +47 2270 8250 Local call tariff Poland +48 0223491505 Local call tariff Portugal +351 2 1359 1440 Local call tariff Spain +34 902 888 785 €0.10 Sweden +46 08 632 0016 Local call tariff Switzerland +41 02 2310 2116 Local call tariff United Kingdom +44 0207 949 0069 Local call tariff 31

Your Guarantee in Central and Eastern Europe Dear Customer, Thank you for purchasing this Philips product, which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts during a period of 24 months from date of purchase. What is covered? This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary, Slovakia, Slovenia, Russia and Turkey and only for monitors originally designed, manufactured, approved and/or authorized for usage within these countries. Warranty coverage begins as from the day you buy your monitor. For 2 years thereafter, your monitor will be serviced in case of defects provided for under the warranty coverage. What is excluded? The Philips guarantee applies provided the product is handled properly for its intended use, in accordance with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase, dealer's name and model and production number of the product. The Philips guarantee may not apply if: the documents have been altered in any way • or made illegible; the model or production number on the • product has been altered, deleted, removed or made illegible; repairs or product modifications and lterations • have been executed by unauthorized service organizations or persons; damage is caused by accidents including but • not limited to lightning, water or fire, misuse or neglect. 32 Reception problems caused by signal • conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the • monitor; Product requires modification or adaptation • to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country. Please note that the product is not defective under this guarantee in the case where modifications become necessary in order for the product to comply with local or national technical standards which apply in countries for which the product was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific country. Just a click away In case of any problems, we advise you to read the operating instructions carefully or go to the philips.com/support website for additional support. Just a phone call away In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully before contacting our dealers or Information Centers In case your Philips product is not working correctly or is defective, please contact your Philips dealer or directly the Philips Service and Consumer Information Centers Website: philips.com/support Consumer Information Centers Argentina / Australia / Brasil / Canada / New Zealand / Belarus / Bulgaria / Croatia / Czech Republic / Estonia / United Arab Emirates / Hong Kong / Hungary / India / Indonesia / Israel / Latvia / Lithuania / Malaysia / Middle East + North Africa / New Zealand / Pakistan / Romania / Russia / Serbia & Montenegro / Singapore / Slovakia / Slovenia / South Africa / South Korea / Taiwan / Philippines / Thailand / Turkey / Ukraine / Vietnam Eastern Europe BELARUS Technic al Center of JV IBA M. Bogdanovich str. 155 BY - 220040 Minsk Tel: +375 17 217 33 86 BELARUS Service.BY Petrus Brovky st. 19 – 101-B 220072, Minsk Belarus BULGARIA LAN Service 140, Mimi Balkanska Str. Office center Translog 1540 Sofia, Bulgaria Tel: +359 2 960 2360 lan-service.bg CZECH REPUBLIC General Consumer Information Center 800 142100 Xpectrum Lu.ná 591/4 CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121 435 Email:info@xpectrum.cz xpectrum.cz 33 CROATIA Renoprom d.o.o. Ljubljanska 4, Sv. Nedjelja,10431 Croatia Tel: +385 1 333 0974 ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE-12618 Tallinn Tel: +372 6519900 ee.invia.fujitsu.com HUNGARY Serware Szerviz Vizimolnár u. 2-4 HU - 1031 Budapest Tel: +36 1 2426331 Email: inbox@serware.hu serware.hu HUNGARY Profi Service Center Ltd. 123 Kulso-Vaci Street, H-1044 Budapest ( Europe Center ) Hungary Tel: +36 1 814 8080 m.andras@psc.hu LATVIA ServiceNet LV Jelgavas iela 36 LV - 1055 Riga, Tel: +371 7460399 Email: serviss@servicenet.lv LITHUANIA ServiceNet LT Gaiziunu G. 3 LT - 3009 KAUNAS Tel: +370 7400088 Email: servisas@servicenet.lt servicenet.lt ROMANIA Blue Ridge Int'l Computers SRL 115, Mihai Eminescu St., Sector 2 RO - 020074 Bucharest Tel: +40 21 2101969 SERBIA & MONTENEGRO Kim Tec d.o.o. Viline vode bb, Slobodna zona Beograd L12/3 11000 Belgrade Serbia Tel. +381 11 20 70 684 SLOVAKIA General Consumer Information Center 0800004551 Datalan Servisne Stredisko Puchovska 8 SK - 831 06 Bratislava Tel: +421 2 49207155 Email: servis@datalan.sk SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si RUSSIA CPS 18, Shelepihinskaya nab. 123290 Moscow Russia Tel. +7(495)797 3434 Profservice: 14A -3, 2Karacharovskaya str, 109202, Moscow , Russia Tel. +7(095)170-5401 34 TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.Cadde No:22 34776-Umraniye/Istanbul Tel: (0800)-261 33 02 UKRAINE Comel Shevchenko street 32 UA - 49030 Dnepropetrovsk Tel: +380 562320045 csp-comel.com LLC Topaz Company Topaz-Service Company, Mishina str. 3, Kiev Ukraine-03151 Tel: +38 044 245 73 31 Latin America ARGENTINA Azopardo 1480. (C1107ADZ) Cdad. de Buenos Aires Tel: 0800 3330 856 Email: CIC.monitores@Philips.com BRASIL Alameda Raja Gabaglia, 188 - 10°Andar - V. Olímpia - S. Paulo/SP - CEP 04551-090 - Brasil Tel: 0800-7254101 Email: CIC.monitores@Philips.com Pacific AUSTRALIA Company: AGOS NETWORK PTY LTD Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia Tel: 1300 360 386 Fax: +61-2-80808147 Email: philips@agos.com.au Service hours: Mon.~Fri. 8:00am-7:30pm NEW ZEALAND Company: Visual Group Ltd. Address: 28 Walls Rd Penrose Auckland Phone: 0800 657447 Fax: 09 5809607 E-mail: vai.ravindran@visualgroup.co.nz Service Hours: Mon.~Fri. 8:30am~5:30pm Asia HONG KONG/Macau Company Name: PHK Service Limited Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong Kong Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau E-mail: enquiry@phkservice.com.hk Service Hours: Mon.~Sat. 09:00am~06:00pm India Company: REDINGTON INDIA LTD Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India Tel: +9144-42243352/353 E-mail: aftersales@in.aocmonitor.com Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM Indonesia Company Name: PT. Gadingsari elektronika Prima Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang. Jakarta Tel: 021-750909053, 021-750909056 Fax: 021-7510982 E-mail: gepta@cbn.net.id Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm 35 Additional service points: 1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan. Phone: 021-7940040, ext 1722/1724, 98249295, 70980942 2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat. Phone: 021-3455150, 34835453 3. Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-45870601, 98131424 South Korea Company: PCS One Korea Ltd. Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea Call Center Tel: 080-600-6600 Tel: 82 2 591 1528 Fax: 82 2 595 9688 E-mail: cic_korea@philips.com Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM Malaysia Company: After Market Solutions (CE) Sdn Bhd Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia. Phone: 603 7953 3370 Philips Info Line: 1-800-880-180 Fax: 603 7953 3338 E-mail: pceinfo.my@philips.com Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm Pakistan Philips Consumer Service Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400 Tel: (9221) 2737411-16 Fax: (9221) 2721167 E-mail: care@philips.com Website: philips.com.p Singapore Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center) Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762 Tel: (65) 6882 3999 Fax: (65) 62508037 E-mail: consumer.care.sg@philips.com Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm Taiwan Company: FETEC.CO Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800 Consumer Care: 0800-231-099 Tel: (03)2120336 Fax: (03)3129184 E-mail: knlin08@xuite.net Service hours: Mon.~Fri. 8:30am~7:00pm Thailand Company: Axis Computer System Co., Ltd. Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310 Thailand Tel: (662) 934-5498 Fax: (662) 934-5499 E-mail: axis5@axiscomputer.co.th Service Hours: Mon.~Fri. 08:30am~05:30pm Glee Electronics Inc Contact nos. (632) 636-3636 / 7064028 to 29 Fax no. (632) 7064026 Receiving Centers NEO CARE - Megamall 4th Level Cyberzone, Building B, SM Megamall, Mandaluyong City NEO CARE - SM North EDSA 4th Level Cyberzone, Annex Bldg. SM City North EDSA, Quezon City 441-1610 36 MDR Microware Sales Inc. Cebu Branch N. Escario corner Clavano St., Cebu City Phils. # 255-4415/ 255-3242/253-9361/4124864 to 67 Sun # 0922-8210045 to 46 Davao Office: C. Arellano St., Davao City 8000 082- 225-3021/225-3022 Sun# 0922-8210015 CDO Office: 1445 Corrales Ext.,CDO City 088-856-8540/856-8541 Sun # 0922-8210080 Iloilo Office: C. Lim Comp., Gomez St., Iloilo City # 033 338-4159/ 033 508-3741 Sun # 0922-8808850 Africa SOUTH AFRICA Company name: Sylvara Technologies Pty Ltd Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa Tel: +27878084456 Fax: +2711 391 1060 E-mail: customercare@philipssupport.co.za Service hours: Mon.~ Fri. 08:00am~05:00pm Middle East Middle East + North Africa Company: AL SHAHD COMPUTER L.L.C Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES TEL: 00971 4 2276525 FAX: 00971 4 2276242 E-mail: shahd52@eim.ae Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm Israel Company: Eastronics LTD Your Philips F1rst Choice Warranty(USA) Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel Thank you for purchasing this Philips monitor. Tel: 1-800-567000 call free in Israel; (972-50- 8353722 after service hours until 20:00) Fax: 972-3-6458759 E-mail: eastronics@eastronics.co.il Service hours: Sun.~Thurs. 08:00 - 18:00 LIMITED WARRANTY (Computer Monitor) All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty. This two-year service warranty entitles you to a swap model on-site within 48 hours of your call being received within the first year of purchase. If you have any problems with your monitor within the second or third year of purchase, we will repair it after it has been sent to the service provider at your expense and returned to you within five working days, free of charge.

Click here to access the Warranty Registration Card. Two Years Free Labor / Two Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two. 37

WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. Attach it to this owner's manual and keep both nearby. WHAT IS COVERED? Warranty coverage begins the day you buy your product. For two years thereafter, all parts will be repaired or replaced, and labor is free. After two years from the day of purchase, you pay for the replacement or repair of all parts, and for all labor charges. All parts, including repaired and replaced parts, are covered only for the original warranty period. When the warranty on the original product expires, the warranty on all replaced and repaired products and parts also expires. WHAT IS EXCLUDED? Your warranty does not cover: labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics. reception problems caused by signal conditions or cable or antenna systems outside the unit. 38 a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications. incidental or consequential damages resulting from the product. (Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not copyrighted.) the model or production number on the product has been altered, deleted, removed or made illegible. Where IS SERVICE AVAILABLE? Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the product, the local Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available). Where CAN I GET MORE INFORMATION? For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A. customers only) or (919) 573-7855. Before Requesting Service... Please check your owner's manual before requesting service. Adjustments of the controls discussed there may save you a service call. TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS... Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing: Philips Customer Care Center (877) 835-1838 or (919) 573-7855 (In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty. But, because some states do not allow limitations on how long an implied warranty may last, this limitation may not apply to you.) TO GET WARRANTY SERVICE IN CANADA... Please contact Philips at: (800) 479-6696 Two years free parts and two years free labor will be provided at Philips Canada depot or any one of its authorized service centers. (In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including any implied warranties of merchantability or fitness for a particular purpose. Philips is not liable under any circumstances for any direct, indirect, special, incidental or consequential damages, howsoever incurred, even if notified of the possibility of such damages.) REMEMBER... Please record the model and serial numbers found on the product below. MODEL # ______________________________ SERIAL # _______________________________ This warranty gives you specific legal rights. You may have other rights which vary from state/ province to state/province. Before contacting Philips, please prepare the 39 following details so we can solve your problem quickly. Philips type number • Philips serial number • Purchase date (copy of purchase may be • required) PC environment Processor: • o CUP and Graphic card name and driver version o Operating system o Application being used Other cards installed • Having the following information available will also help speed up the process: Your proof of purchase indicating: date of • purchase, dealer name, model and product serial number. The full address to which the swap model • should be delivered. Just a phone call away Philips’ customer help desks are located worldwide. Within the U.S. you can contact Philips customer care Monday-Friday from 8:00 AM- 9:00 PM Eastern Time (ET) and on Saturdays from 10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers. For more information on this and more great Philips products visit our website at: Website: philips.com Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase. This international Philips guarantee complements the existing national guarantee obligations to you of dealers and Philips in the country of purchase and does not affect your statutory rights as a customer. The Philips guarantee applies provided the product is handled properly for its intended use, in accordance with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase, dealer's name and model and production number of the product. The Philips guarantee may not apply if: the documents have been altered in any way • or made illegible; the model or production number on the • product has been altered, deleted, removed or made illegible; repairs or product modifications and • alterations have been executed by unauthorized service organizations or persons; damage is caused by accidents including but • not limited to lightning, water or fire, misuse or neglect. 40 Please note that the product is not defective under this guarantee in the case where modifications become necessary in order for the product to comply with local or national technical standards which apply in countries for which the product was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific country. In case your Philips product is not working correctly or is defective, please contact your Philips dealer. In the event you require service whilst in another country a dealer address can be given to you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can be found in the relevant part of this booklet. In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully before contacting your dealer. If you have questions which your dealer cannot answer or any related question please contact the Philips Consumer Information Centers or via: Website: philips.com 7.1 Troubleshooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Common Problems No Picture (Power LED not lit) Make sure the power cord is plugged into the • power outlet and into the back of the monitor. First, ensure that the power button on the • front of the monitor is in the OFF position, then press it to the ON position. No Picture (Power LED is white blinking) Make sure the computer is turned on. • Make sure the signal cable is properly • connected to your computer. make sure the monitor cable has no bent pins • on the connect side. If yes, repair or replace the cable. The Energy Saving feature may be activated •Screen says Make sure the monitor cable is properly • connected to your computer. (Also refer to the Quick Set-Up Guide). Check to see if the monitor cable has bent • pins. Make sure the computer is turned on. • 7 Troubleshooting & FAQs 41 AUTO button doesn't function The auto function is applicable only in • VGA-Analog mode. If the result is not satisfactory, you can do manual adjustments via the OSD menu. Note The Auto Function is not applicable in DVI-Digital mode as it is not necessary. Visible signs of smoke or sparks Do not perform any troubleshooting steps • Disconnect the monitor from mains power • source immediately for safety Contact with Philips customer service • representative immediately. Imaging Problems Image is not centered Adjust the image position using the “Auto” • function in OSD Main Controls. Adjust the image position using the Phase/ • Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Image vibrates on the screen Check that the signal cable is properly securely • connected to the graphics board or PC. Vertical flicker appears Adjust the image using the “Auto” function in • OSD Main Controls. Eliminate the vertical bars using the Phase/ • Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Horizontal flicker appears Adjust the image using the “Auto” function in • OSD Main Controls. Eliminate the vertical bars using the Phase/ • Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Image appears blurred, indistinct or too dark Adjust the contrast and brightness on On- • Screen Display. An "after-image", "burn-in" or "ghost image" remains after the power has been turned off. Uninterrupted display of still or static images • over an extended period may cause " burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burn-in", "after- imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off. Always activate a moving screen saver • program when you leave your monitor unattended. Always activate a periodic screen refresh • application if your LCD monitor will display unchanging static content. Severe” burn-in” or “after-image” or “ghost • image” symptoms will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Image appears distorted. Text is fuzzy or blurred. Set the PC’s display resolution to the same • mode as monitor’s recommended screen native resolution. 42 Green, red, blue, dark, and white dots appears on the screen The remaining dots are normal characteristic • of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail. The "power on" light is too strong and is disturbing You can adjust “power on” light using the • power LED Setup in OSD main Controls. For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative. 7.2 SmartControl Lite FAQs Q1. I change the monitor on a PC to a different one and the SmartControl Lite becomes un-usable, what do I do? Ans.: Restart your PC and see if SmartControl Lite can work. Otherwise, you will need to remove and re-install SmartControl Lite to ensure proper driver is installed. Q2. The SmartControl Lite functions worked well before, but it does not work anymore, what can I do? Ans.: If the following actions were executed, the monitor driver may need to be re-installed. Changed video graphic adapter to another • one Updated video driver • Activities on OS, such as service pack or • patch Run Windows Update and updated monitor • and/or video driver Windows was booted with the monitor • power off or disconnected. To find out, please right click My Computer and click on Properties->Hardware-> Device Manager. If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl Lite and re- install it. 43 Q3. After installing SmartControl Lite, when clicking on SmartControl Lite tab, nothing shows up after a while or a failure message shows, what happened? compatible with the SmartControl Lite. If your graphic adaptor is one of the above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl Lite, and re-install it once more. If it is still not working, we are sorry that the graphic adaptor is not supported. Please visit Philips website and check if an updated SmartControl Lite driver is available. Q4. When I click on Product Information, only partial information is shown, what happened? Ans.: It might be your graphic card adaptor driver is not the most updated version which fully supporting DDC/CI interface. Please try to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl Lite and re-install it once more.

Ans.: It might be your graphic adaptor is not Q5. I forgot my PIN for Theft Deterrence Function. How can I do? Ans.: Philips Service center has a right to ask for legitimate identification and authorization, in order to establish ownership of the monitor.

7.3 General FAQs Q1: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? Ans.: Recommended resolution for Philips 18.5": 1366x768 @60Hz. Unplug all cables, then connect your PC to • the monitor that you used previously. In the Windows Start Menu, select Settings/ • Control Panel. In the Control Panel Window, select the Display icon. Inside the Display Control Panel, select the 'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the sidebar to 1366x768 pixels (18.5"). Open 'Advanced Properties' and set the • Refresh Rate to 60Hz, then click OK. Restart your computer and repeat step • 2 and 3 to verify that your PC is set at 1366x768@60Hz (18.5"). Shut down your computer, disconnect your • old monitor and reconnect your Philips LCD monitor. Turn on your monitor and then turn on • your PC. Q2: What does the recommended refresh rate for LCD monitor? Ans.: Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance on screen, you can set it up to 75Hz to see if that removes the disturbance. 44 Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .icm)? Ans.: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the (companion CD-ROM) included in this package. Monitor drivers (.inf and .icm files) will be installed automatically. Q4: How do I adjust the resolution? Ans.: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under Windows® Control Panel with the "Display properties". Q5: What if I get lost when I am making monitor adjustments via OSD? Ans.: Simply press the OK button, then select 'Reset' to recall all of the original factory settings. Q6: Is the LCD screen resistant to scratches? Ans.: In general it is recommended that the panel surface is not subjected to excessive shocks and is protected from sharp or blunt objects. When handling the monitor, make sure that there is no pressure or force applied to the panel surface side. This may affect your warranty conditions. Q7: How should I clean the LCD surface? Ans.: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc. Q8: Can I change the color setting of my monitor? Ans.: Yes, you can change your color setting through OSD control as the following procedures, • Press "OK" to show the OSD (On Screen Display) menu • Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below. 1. Color Temperature; The 2 settings are 6500K, and 9300K. 2. sRGB; this is a standard setting for ensuring correct exchange of colors between different device (e.g. digital cameras, monitors, printers, scanners, etc) 3. User Define; the user can choose his/her preference color setting by adjusting red, green blue color. Note: A measurement of the color of light radiated by an object while it is being heated. This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K. 45 Q9: Can the Philips LCD Monitor be mounted on the wall? Ans.: Yes. Philips LCD monitors have this optional feature. Four standard VESA mount holes on the rear cover allows the user to mount the Philips monitor on most of the VESA standard arms or accessories. We recommend you to contact your Philips sales representative for more information. Q10: Can I connect my LCD monitor to any PC, workstation or Mac? Ans.: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and workstations. You may need a cable adapter to connect the monitor to your Mac system. Please contact your Philips sales representative for more information. Q11: Are Philips LCD monitors Plug-and- Play? Ans.: Yes, the monitors are Plug-and-Play compatible with Windows 7/Vista/XP/NT, Mac OSX, Linux Q12: What kind of wide-angle technology is available? Ans.: Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA, or PVA technologies. TN panels have improved over the years, but IPS panel still gives superior results over TN panel.

Q13: What is Image Sticking, or Image Burn- in, or After Image, or Ghost Image in LCD panels? Ans.: Uninterrupted display of still or static images over an extended period may cause "burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn- in", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "atter-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off. Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content. Warning Severe"burn-in" or "after-image" or "ghost image" symptoms will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Q14: Why is my Display not showing sharp text, and is displaying jagged characters? Ans.: Your LCD monitor works best at its native resolution of 1366x768@60Hz. For best display please use this resolution. 46 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used under license from Koninklijke Philips Electronics N.V. Specifications are subject to change without notice. Version: 192E2/192EL2 v1.0


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply