PETDIARY T730 (01) PDF DOCUMENT

Training collars are used to train the dogs and not for punishment. Use properly with care and the collar can be a safe and effective tool to train, building communication and strengthen your bond with your best friend. Obey all safety messages that follow this instruction to avoid possible injury.

If your dog knows the command but responds inconsistently or acts slower than your requirement, a training collar can sharpen his skill.

For example, you have taught your dog to come when called, but over time he responds slower. You can communicate with him via the remote trainer, so that he immediately responds to your call.

1.Set the collar to initial stimulation level and test it.

2.Fit the collar on your dog’s neck along with his regular collar.

3.Let him roam around the training area. Then give the command and simultaneously press the stimulation button.

4.The instant your dog moves toward you, stop stimulation and praise him.

5.If he stops before he reaches you or turns away repeat the command and continue the stimulation. Again, stop at the instant he runs to you and reward him by praising him or feeding him a treat. Repeat this for 3 or 4 times.

1. If he doesn’t get it for the first few times, don’t give up and do not increase the stimulation. Try to work on this a couple of times per day.

2. During the training period never give the command if you are not able to enforce it.

3. Your dog has to make the mental connection between the static stimulation/vibration/beep to his behavior (may take a week or more for some dogs)

Altogether, both methods of stopping unwanted behavior and reinforcing learning behaviors can be applied to nearly every training scenario.

1. Do not expose to extreme heat or store at temperatures above 113 °F or 45 °C.

2. Please always keep the training collar out of reach of children.

3. Charge the remote transmitter and receiver at least 2 hours when receive the item. The collar cannot receive any signal while it is being charged.

1. Avoid leaving the collar on the dog for more than 12 hours per day.

2. When possible, reposition the collar on the pet’s neck every 1 to 2 hours.

3. Check the fit to prevent excessive pressure.

4. Take off the receiver when your dog is swimming.

1x Handheld Transmitter

2x Receiver with Nylon Collar Strap

2x USB Charging Cables

4x Silicone Caps

1x Test Light

1x User Manual

1x Lanyard

1. Please examine regularly to ensure tightness of the transmitter and eliminate any external damages.

2. Clean the screw caps with alcohol weekly.

3. Examine your dog’s neck and carry out weekly cleanup.

4. The battery is rechargeable. In order to maintain battery life, please charge it once a month if it is not used.

1. LCD Screen: The LCD screen will display training modes, channels, intensity level and battery indicator.

2. Static Stimulation Button: Pressing the “Static Stimulation” button, the receiver will emit static stimulation. If set level 0, NO stimulation.

3. Vibration Button: Pressing the “Vibration” button, the receiver will vibrate. If set level 0, NO vibration.

4. Beep Button: Pressing the “Beep” button, the receiver will emit beep sound. If set level 0, NO beep.

5. Intensity Up/down Buttons: Select intensity level of beep, vibration and static Stimulation.

6. Channel Button: Pressing this “A B” button will shift channel between the first and second collar receiver.

7. Charging port: Insert charging cable into charging port to charge the Transmitter.

8. Power Button: Turn on/off the receiver by press the “Power” button one time.

9. Touch Points

10. Indicator Light

1. Connect the charger cable to the charging port.

2. Plug the charger into a standard outlet.

3. The battery icon will flash during charging and be solid when charging is completed.

1. Press any button to activate the transmitter. The backlight is on.

2. The backlight will stay for about 5 seconds and will be off without interaction.

3. The transmitter goes into deep sleep mode after 50 seconds without interaction. Follow step 1 to activate transmitter.

1. Open the rubber cover, connect the receiver to a charger into a standard socket.

2. The indicator light flashes red slowly during charging, while the red light keeps on when fully charged.

Turn on: Press the power button once, the indicator light shows red and means that the receiver is turned on.

Turn off: Hold the power button for about 3 seconds, the indicator light is off and means that the receiver is turned off.

When the indicator light keeps on flashing in red, it means low battery.

1. Turn on the transmitter and the receiver.

2. Press A/B button on right side of transmitter to select one of the dog channels.

3. Press any function button to pair with receiver. The indicator will flash in green if pairing is successful.

4. If you need to pair one more receiver, simply choose another channel and pair by following step 2 and 3.

1. Please remember the dog channel you choose and do not change to other channel, or the remote control will be invalid.

2. You need to pair remote transmitter and receiver before using it on the dog. Please follow the user guide for the first use.

3. The training system will fall into deep sleep mode after 50 seconds without interaction. Please reactivate the receiver by pressing any button on the remote and press any function button one more time to deliver signal to the receiver.

Please use test light to test static stimulation function. Press the static stimulation function button, the test light will shine. Press “+/-” button to adjust static shock levels from level 0-16.

Press the vibration function button, the receiver will shake. Press “+/-” button to adjust vibration levels from level 0-8.

Press tone button, the receiver will make a long “beep” sound for 3 seconds. Press “+/-” button to adjust vibration levels from level 0-3.

1. The correct wearing position helps training effective and healthy. The receiver shall be placed on bottom of the pet’s neck, and the screw cap must contact the pet’s skin directly.

2. The space between receiver collar and the pet’s neck shall be maintained to a finger distance, not too loose or too tight.

Large Dog (Body height above 24 inch, Weight above 88 lbs)

Medium Dog (Height 16-24 inch, Weight 24.2-66 lbs)

Small Dog (Height 10-16 inch, Weight 8.8-22 lbs)

Mini Dog (Height under 10 inch, Weight under 8.8 lbs)

It is safe to use vibration and stimulation while training your pet. Please test the functions begin from level 1 to observe your pet’s reaction. For first time. Please follow our user guide to use this item better.

Your pet should be able to recognize basic commands such as “Sit” or “Stay”. It fits all breeds and sizes aged above 6 months, weighing between 10–110 lb and with neck sizes of 5-20″.

You may need to reinforce training with the receiver collar from time to time.

It’s water resistant and rainproof. Please be sure to keep the rubber cover put in the right position and remove the receiver from your dog when he/she is swimming.

The stimulation will last for 5 seconds and vibration last for 10 seconds when you hold to press the button. After that, the Vibration and stimulation signal cannot be delivered until You release and press the button again. In this way, your pet could be protected.

Training sessions should be positive and short. It is better to train for about 10-15 minutes each time.

It depends on your dog’s temperament and threshold for Vibration/Stimulation. Always start at the lowest level and work your way up. You will get the appropriate level when the dog responds to the vibration or stimulation with a mild reaction, such as a tensing of the neck muscles. The vibration or stimulation Level may vary depending on the training situation. When highly distracted, your dog requires a higher level of vibration or stimulation.