Post questions, comments, reviews or errors in the comment box below.
Your File is Ready … Download PDF
PDF Content Summary: IRG5520 Series Routers Quick Start Guide 5500451-10 (Rev A) Version #A11.08.2019 1
IRG5520 Series Routers Quick Start Guide _____________________________________ This guide covers basic installation and configuration and is intended for first time setup or product evaluation. The models covered by this guide are the IRG5520, IRG5520+, IRG5521, IRG5521+ and the IRG5521+ FN. Complete details can be found in the following guides at http://www.perle.com/downloads. • IRG5520 Series Routers Hardware Installation Guide • IRG5000 Series Routers User’s Guide • IRG5000 Series Routers Command Line Reference Guide. What’s in the box? • IRG5520/5520+/5521/5521+/5521+ FN Router • 4 LTE/Wireless antennas (depending on model) • DC Power cable – pigtail (depending on model) • 12VDC/2A power supply (depending on model) • Enclosure mounting screws • IRG5520 Series Router Quick Start Guide (this guide) • Optional – GPS passive or active antenna (order-able from Perle) • Optional – DIN Rail mounting kit (order-able from Perle)
IRG5520 Series Routers Quick Start Guide 5500451-10 (Rev A) Version #A11.08.2019 Getting Started The steps for a typical installation are: 1. Inserting the SIM card/s. 2. Connecting antenna/s. 3. Connecting the Power. 4. Connecting to the Cellular Network. 5. Fast Setup Mode. Inserting the SIM cards Use only mini-SIM (2FF) cards. Ensure the power is disconnected before you insert the SIM card/s (see below). 1. Unscrew the screws and gently pry the SIM cover loose from the opening (see below). 2. Align the SIM card so that the SIM card will slide into the top slot (slot#1) ensuring that the SIM card connectors will be facing the router’s printed circuit board. Always populate slot#1 first. 3. Align the SIM cover plate and secure the plate with the screws. 2 IRG5520 Series Routers Quick Start Guide 5500451-10 (Rev A) Version #A11.08.2019 3
Connecting the Antennas 1. Connect your cellular antenna to connector Main. 2. Connect the diversity antenna to connector Diversity. 3. Connect a WLAN antenna to connector WLAN-1. 4. Connect a WLAN antenna to connector WLAN-2. 5. Connect your GPS antenna to connector GNSS. See Figure 2 Connecting the Power See Figure 2 for wiring requirements. Colors indicated are for the Perle supplied DC power cable. Connecting the Network When the router is powered on, it begins the process of activation and attempts to connect to the cellular network. This process typically takes a few minutes. A successful connection is indicated by a solid green Internet LED, if not, see the IRG5520 Series Routers Hardware Installation Guide for details.
IRG5520 Series Routers Quick Start Guide 5500451-10 (Rev A) Version #A11.08.2019 Fast Setup Mode 4
Fast Setup provides a simple method of doing an initial setup from a PC. Your router is shipped in factory default mode. 1. Your PC must be set to obtain an IP address automatically using DHCP. 2. Plug the PC into your router’s Ethernet interface or connect to the wireless LAN (WIFI) using the credentials printed on the label of your router. 3. When the Power LED is flashing green, use a web browser, enter http://192.168.0.1 to access your router. On the setup screen, select, Getting Started. 4. Once connected, fill in the required fields, apply changes to save and exit. The configuration changes will be immediately applied to the router 5. The router’s web configuration sign on screen will be displayed. Using the credentials, you previously defined in Step 4, you can now access your router’s full configuration. For alternative methods of performing and initial setup see the IRG5520 Series Routers Hardware Installation Guide. © 2019 Perle Systems Limited. All rights reserved.
FREE ENGLISH PDF
USER GUIDE - USER MANUAL
OWNER GUIDE - OWNER MANUAL
REFERENCE GUIDE - REFERENCE MANUAL
INSTRUCTION GUIDE - INSTRUCTION MANUAL