FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF USER GUIDE
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF USER MANUAL
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF OWNER GUIDE
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF OWNER MANUAL
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF REFERENCE GUIDE
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF REFERENCE MANUAL
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH PANASONIC TY-ST43PE9 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD PANASONIC TY-ST43PE9 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
PANASONIC TY-ST43PE9 (01) PDF SUMMARY:
What should I do before assembling the product?
Read the Operating Instructions carefully so that the product can be properly and safely assembled. Make sure to read “Safety precautions” in particular before assembling the product.
What should I do with the Operating Instructions after reading them?
Keep the Operating Instructions in a safe place, together with the operating instructions for the display.
What should I not do with the pedestal?
Do not disassemble or modify the pedestal. Doing so may cause the unit to fall over and become damaged, which may result in personal injury.
What should I do with the fixing screws?
Keep the fixing screw out of reach of children to prevent swallowing. In case of swallowing of the fixing screws, consult a doctor immediately.
Should I install the display vertically using the pedestal?
Do not install the display vertically using the pedestal. Doing so may cause the unit to fall over and become damaged, which may result in personal injury.
Where should I install the pedestal?
Install the pedestal at the hole position where the distance between the base and the bottom surface of the display is the smallest. Doing so may cause the unit to fall over and become damaged, which may result in personal injury.
What displays should I use with the pedestal?
Do not use any displays other than those given in the catalogue. Doing so may cause the unit to fall over and become damaged, which may result in personal injury.
What should I not do with the pedestal or attached equipment?
Do not climb on or hang from the pedestal or attached equipment. Doing so may cause the unit to fall over and become damaged, which may result in personal injury. (Be particularly careful that young children obey this caution.)
What should I do if the pedestal is bent or deformed?
Do not use the pedestal if it has become bent or deformed for any reason. Doing so may cause the unit to fall over and become damaged, which may result in personal injury.
What should I not do with the ventilation holes of the display?
Do not block the ventilation holes of display. When using the pedestal, do not block the space between the bottom surface of the display and the floor surface. Otherwise heat may build up inside and cause a fire.
Where should I not use the pedestal?
Do not use in places with high humidity.
What may happen after prolonged use?
After prolonged use, the pedestal may warp or become deformed, reducing its strength. This may lead to the unit falling over and becoming damaged, which may also result in personal injury.
What space is required when installing the display?
When installing the display, ensure there is at least a 10 cm (3.9 inches) space above and to the sides of, and a 5 cm (2.0 inches) space to the rear of the display. Failing to do so may result in a fire.
How many people are required to install and remove the display from the pedestal?
Two people are required to install and remove the display from the pedestal. The display may fall and cause injury.
What should I do during setting-up?
During setting-up, make sure that all screws are securely tightened. If assembly is not performed correctly, the pedestal will not be able to support the weight of the display. This may result in the display falling over and becoming damaged, which may result in personal injury.
What should I use for installation?
For installation, use the special-purpose constituent parts. Otherwise, the display may fall off the wall, possibly causing injury.
Where should the pedestal be set up?
Set up on a stable, level surface. Failure to do so may cause the unit to fall over and become damaged, which may result in personal injury.
Where should I keep the unit?
Keep the unit away from direct sunlight and heating equipment. Failure to do so may cause warping, deformation, or degradation of materials which may result in a loss of strength that may cause the equipment to fall over or break and cause injury.
What should I use to secure the display?
Use the overturn/fall-prevention accessory to secure the Display. If an earthquake occurs or children climb onto the pedestal with the Display installed, the unit may overturn or fall over, resulting in personal injury.
What should I not do to the display’s edges after installing the pedestal?
After installing the pedestal, do not subject the display’s right/left/top edge to any excessive force or physical shock. Doing so may cause the unit to fall over and become damaged, which may result in personal injury.
What should I consider when selecting the location for the display?
Exercise care when selecting the location for the display because it may discolor or deform due to light or heat if it is placed where it is exposed to direct sunlight, or near a heater.
How should I clean the pedestal?
Clean the pedestal by wiping it with a soft, dry cloth (such as cotton or flannel). If the bracket is very dirty, remove the dirt using a neutral detergent diluted in water, and then wipe it clean with a dry cloth. Do not use benzene, thinner, or furniture wax as this may cause the coating to peel.
What should I not affix to the product?
Do not affix adhesive tape or stickers to the product. Doing so may dirty the surface of the pedestal. Do not allow long-term contact with rubber, vinyl products or the like. (Doing so will cause deterioration.)
What should I not subject the display to?
Do not subject the display to any excessive force or physical shock.
What type of power supply outlet should I use for the display?
For the display power supply plug, use a power supply outlet that can be reached easily.
What should I ensure regarding air flow?
Ensure good air flow so that the ambient temperature does not exceed 40 °C (104 °F). Failure to do this may cause heat to build up inside the display, resulting in malfunction.
What responsibility does Panasonic not assume?
Panasonic shall assume no responsibility whatsoever for any damage or accident resulting from improper assembly or the assembly of the product in any manner not specified in the operating instructions or without using designated parts.
What should I do with products that are no longer being used?
Remove products that are no longer being used.
What is the pedestal intended for?
This pedestal is intended for only Panasonic display models. Use with other apparatus is capable of resulting in instability causing possible injury.
What should I do with the package after unpacking the product?
Properly dispose of the package after unpacking the product.
What should I do with small parts?
Safely store small parts to keep them out of the reach of infants and young children.
What should I do with screw tightening torques?
Manage screw tightening torques according to the torques specified in the assembly procedure.
What tools should I use when tightening screws?
In tightening screws, use such a tool as a torque screwdriver or torque wrench. Do not use an electric screwdriver and impact screwdriver.
How many people are required for installation?
Installation must be carried out by at least two people.
How should I place the display when preparing it for assembly?
Spreading out a soft cloth, etc., place the display with the screen facing down. Be careful not to damage the display screen, for example, by dragging it. When placing the display with the screen facing down, or lifting it up, never hold or put pressure on the LCD screen. The LCD screen may be damaged.
How should I attach the pedestal tubes?
Place the pedestal tubes to fit the holes at the back of the display. Locate the nuts inside. (The side with the nuts comes to the downside.) Use the hole position where the distance between the base and the bottom surface of the display is the smallest when the base is attached.
How should I fix the pedestal tubes?
Fix with the 4 display installation screws. Tightening torque: 1.6 to 2.2 N•m.
Should I install the display vertically using the pedestal?
Do not install the display vertically using the pedestal.
How should I attach the base?
Position the convex part side at the front side of the display. Insert the base to the pedestal tube. Make sure that the orientation of the front side and back side of the base are correct. Be careful not to drop. Fix the bases (upper part) with the 2 base installation screws. Tighten the base installation screws from the outside of the pedestal tube. Tightening torque: 1.2 to 1.5 N•m. Using the 2 base installation screws, fix the bases (lower part) together with the 2 overturn-prevention belts and the 2 spacers. Tighten the base installation screws from the outside of the pedestal tube. Tightening torque: 1.2 to 1.5 N•m.
How many people are needed to stand the display vertically?
Make sure to hold the display with more than two people.
What is required when attaching the base?
Be sure to attach the overturn-prevention belt when attaching the base.
Why should I use the overturn/fall prevention accessories?
The equipment may overturn in the event of an earthquake etc. Therefore, always use the overturn/fall prevention accessories.
What do the details in the section about overturn/fall prevention indicate?
The details in this section indicate how to reduce any damage or injury caused by this equipment overturning or falling due to an earthquake. However, there is no guarantee that the overturn/fall prevention accessories will be effective in all earthquake situations.
How should I fix the display to a board?
Fix the 2 overturn-prevention belts attached to the pedestal tube to the TV board with the 2 wood screws. To assemble to the board, use the prepared holes. If there are no prepared holes, drill new holes to the center of the base board width.
How should I fix the display to the wall?
Use a commercially available, sturdy wire to secure it firmly to a wall or pillar. Pass the sturdy wire through the top hole of the pedestal tube. If the display is fixed to the pedestal tube through the top hole of the pedestal tube, pass the string or wire through the second hole.
How do I remove the pedestal?
Remove the display in an opposite way of “Assembly Procedure” after removing the power plug, cables and overturn-prevention items. Please keep the removed items carefully for the time when assembling again.
CLICK HERE TO DOWNLOAD PANASONIC TY-ST43PE9 (01) PDF MANUAL