PANASONIC SB-HW190 (01) PDF MANUAL

PANASONIC SB-HW190 (01) PDF SUMMARY:

What should you do if you have any questions?

Contact: 1-800-211-PANA (7262)

What are some important safety instructions to follow?

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings.
• Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

How do you reduce the risk of fire, electric shock, or product damage?

• Do not expose this unit to rain, moisture, dripping or splashing.
• Do not place objects filled with liquids, such as vases, on this unit.
• Use only the recommended accessories.
• Do not remove covers.
• Do not repair this unit by yourself. Refer servicing to qualified service personnel.

How should you install the unit in regards to the power cord?

Install this unit so that the power cord can be unplugged from the socket outlet immediately if any problem occurs.

What safety precautions should you take when using the unit?

• This unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
• Do not place sources of naked flames, such as lighted candles, on this unit.
• To reduce the risk of fire, electric shock or product damage, do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure this unit is well ventilated.
• Do not obstruct this unit’s ventilation openings with newspapers, tablecloths, curtains, and similar items.

What are the safety instructions for batteries?

• Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer.
• Mishandling of batteries can cause electrolyte leakage and may cause a fire.
• Do not heat or expose to flame.
• Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with doors and windows closed.
• Do not take apart or short circuit.
• Do not recharge alkaline or manganese batteries.
• Do not use batteries if the covering has been peeled off.
• Remove the battery if you do not intend to use the remote control for a long period of time. Store in a cool, dark place.
• When disposing the batteries, please contact your local authorities or dealer and ask for the correct method of disposal.

What is the function of the remote control?

The remote control transmits signals to the unit.

What should you do if the remote control does not work properly?

Check the battery. Operations are possible using the buttons on the remote control, but you can perform the operations on the main unit if the controls are the same.

What are the different speaker system components?

• Front speakers SB-HF171
• Center speaker SB-HC171
• Surround speakers SB-HS171
• Subwoofer SB-HW190

What are the included accessories?

• ∏ 1 Remote control (N2QAYB000702)
• ∏ 1 Remote control battery
• ∏ 1 FM indoor antenna (RSAX0002)
• ∏ 5 Speaker cables (REEX1266A-J: RED) (REEX1267A-J: WHITE) (REEX1268A-J: GREEN) (REEX1269A-J: GRAY) (REEX1270A-J: BLUE)
• ∏ 1 AC power supply cord (K2CB2YY00059)
• ∏ 1 Sheet of speaker cable stickers

What does the lightning flash with arrowhead symbol within an equilateral triangle indicate?

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

What does the exclamation point within an equilateral triangle indicate?

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

How do you avoid interference with other Panasonic equipment?

Other Panasonic audio/video equipment may start functioning when you operate the unit using the supplied remote control. You can operate this unit in another mode by setting the remote control operating mode to “REMOTE 2”. The main unit and remote control must be set to the same mode.

How do you set the remote control operating mode to “REMOTE 2”?

1. Press [EXT-IN]4 to select “AUX”.
2. Press and hold [< OPEN/CLOSE]2 on the main unit and \ on the remote control until the main unit’s display shows “REMOTE 2”.
3. Press and hold [OK]8 and \ on the remote control for at least 2 seconds.

How do you change the mode back to “REMOTE 1”?

Repeat the steps above by replacing \ with .

What is the function of button 1 on the remote control?

Turn the main unit on/off ( 8)

What is the function of button 2 on the remote control?

Select channels and title numbers etc. / Enter numbers ( 9, 11)

What is the function of button 3 on the remote control?

Cancel ( 12)

What is the function of button 4 on the remote control?

Source select

• [DVD]: Select disc as the source ( 11)
• [iPod]: Select iPod®/iPhone® as the source ( 15)
• [EXT-IN, RADIO]: Select the FM tuner or the external audio source ( 9)
  • FM # AUX # ARC # D-IN

What is the function of button 5 on the remote control?

Basic operations for play ( 11)

What is the function of button 6 on the remote control?

Show on-screen menu ( 13)

What is the function of button 7 on the remote control?

Show a disc top menu ( 11)

What is the function of button 8 on the remote control?

Select or confirm menu items / Frame-by-frame ( 11)

What is the function of button 9 on the remote control?

Select the play mode / Set the repeat mode ( 12)

What is the function of button “:” on the remote control?

Select sound mode / Turn Whisper-mode Surround on/off ( 10, 11)

What is the function of button “;” on the remote control?

Select surround sound effects ( 10)

What is the function of button “jSLEEP” on the remote control?

Set the Sleep timer

• Press and hold [jSLEEP].
• While the time is shown on the main unit’s display, press [jSLEEP] repeatedly.

Each time you press the button: SLEEP 30 # SLEEP 60 # SLEEP 90 # SLEEP120 ^————————– OFF (Cancel) (————————}

How do you confirm the remaining time for the sleep timer?

Press and hold the [jSLEEP] button again.

How do you operate the TV using the remote control?

Aim the remote control at the Panasonic TV and press the button.

• [TV, Í]: Turn the TV on/off
• [INPUT, AV]: Change the TV’s video input mode
• [r, VOL, s]: Adjust the TV volume

Why may the TV operations not work properly with some models?

This may not work properly with some models.

What is the function of button “=” on the remote control?

Adjust the volume of the main unit

What is the function of button “>” on the remote control?

Mute the sound

What happens while the mute function is on?

“MUTE” flashes on the main unit’s display while the function is on.

How do you cancel the mute function?

To cancel, press the [>] button again or adjust the volume.

When is mute canceled?

Mute is cancelled when you switch the unit to standby.

What is the function of button “?” on the remote control?

Select radio stations manually ( 9)

What is the function of button “@” on the remote control?

Select preset radio stations ( 9)

What is the function of button “A” on the remote control?

Exit the display

What is the function of button “B” on the remote control?

Show START menu ( 9)

What is the function of button “C” on the remote control?

Show a disc menu ( 11)

What is the function of button “D” on the remote control?

Return to previous screen ( 11)

What is the function of button “E” on the remote control?

Switch information on the main unit’s display ( 11)

What is the function of button “F” on the remote control?

Select speaker channel ( 11)

What is the function of the Standby/on switch (Í/I) on the main unit?

Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.

What is the function of button 2 on the main unit?

Open/Close the disc tray ( 11)

What is the function of button 3 on the main unit?

Adjust the volume of the main unit

What is the function of button 4 on the main unit?

Power indicator. The indicator lights when this unit is turned on.

What is the function of button 6 on the main unit?

Connect iPod/iPhone ( 15)

What are the power-saving features of the main unit?

The main unit is designed to conserve its power consumption and save energy.

• ∫ Auto FL display turn-off function: The main unit’s display is automatically turned off when the volume is adjusted to “0”. ( 17, “FL Control” in Others menu.)
• ∫ Auto power-down function:
  • The main unit will automatically switch to standby mode after 30 minutes of inactivity. e.g.
    • There is no audio signal from an external device.
    • Disc playback is stopped/paused.
    • iPod/iPhone playback is stopped/paused.
    • The disc menu is displayed and play is not selected. (This function may not work depending on the application type of discs.)
  • When the main unit is turned back on, “POWER ON FROM AUTO POWER DOWN MODE” appears on the main unit’s display.

How can you enjoy sound effects from all speakers?

Enjoying surround sound effects.

• Press [SURROUND];.

What are the available surround sound effects for “Surround layout (Recommended)” mode?

Each time you press the button:

• STANDARD: Sound is output as it was recorded/encoded. Speaker output varies depending on the source.
• MULTI-CH: You can enjoy sound from the front speakers, as well as the surround speakers and center speaker even when playing stereo sources.
• MANUAL:
  • While “MANUAL” is displayed, press \8 to select other surround modes. Each time you press \8:
    • DOLBY PLII MOVIE: Suitable for movies, or videos recorded in Dolby Surround.
    • DOLBY PLII MUSIC: Adds 5.1-channel effects to stereo sources.
    • S.SRD (Super Surround): You can enjoy sound from all speakers with stereo sources.
    • STEREO: Sound will only be output to the front speakers and the subwoofer from any source.

What are the recommended modes to enjoy TV audio or stereo sources from all speakers?

“MULTI-CH”, “DOLBY PLII MOVIE”, “DOLBY PLII MUSIC” or “S.SRD”

What are the available surround sound effects for “Front layout (Alternative)” mode?

• STANDARD: Stereo source is output as 2.1-channel audio. When playing surround sources, you can enjoy 5.1-channel surround-like effect even with all the speakers at the front.
• STEREO: You can play any source in stereo. Surround sound effect is unavailable.
• A.SRD (Advanced Surround): You can enjoy surround effect with any audio source.

What will be displayed when the signal is DTS or Dolby Digital?

When the signal is DTS or Dolby Digital, “/DTS” or “/DOLBY DIGITAL” will also be displayed respectively.

How do you select sound mode?

1. Press [SOUND]: to select a sound mode.

Each time you press the button:

• EQ: Equalizer
• SUBW LVL: Subwoofer Level
• C.FOCUS: Center Focus (Only when “Surround layout (Recommended)” mode is selected in “Speaker layout” ( 8, Easy setup).)

1. While the selected mode is displayed, press \8 to make the settings. Refer to the following for setting details of each sound effect.

What should you note when setting up your speakers?

How you set up your speakers can affect the bass and the sound field. Note the following points:

• Place speakers on flat secure bases.
• Keep your speakers at least 10 mm (13/32q) away from the system for proper ventilation.
• Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with thick curtains.
• For optional wall mount, refer to page 19.

How should you place the speakers in the “Surround layout (Recommended)” setup example?

Place the front, center, and surround speakers at approximately the same distance from the seating position. The angles in the diagram are approximate.

• §1 Position with at least 5 cm (2q) of space on all sides for proper ventilation.
• §2 Place it on a rack or shelf. Vibration caused by the speaker can disrupt the picture if it is placed directly on the TV.
• §3 Position it to the right or left of the TV, on the floor or a sturdy shelf so that it will not cause vibration. Leave about 30 cm (1113/16q) from the TV.

Can you use all the speakers at the front?

Depending on the room layout, you may like to use all the speakers at the front (“Front layout (Alternative)”) ( 8, Easy setup).

What are some notes on speaker use?

• Use only supplied speakers. Using other speakers can damage the unit, and sound quality will be negatively affected.
• You can damage your speakers and shorten their lifespan if you play sound at high levels over extended periods.
• Reduce the volume in the following cases to avoid damage:
  • When playing distorted sound.
  • When the speakers are reverberating due to a record player, noise from FM broadcasts, or continuous signals from an oscillator, test disc, or electronic instrument.
  • When adjusting the sound quality.
  • When turning the unit on or off.

What should you do if irregular coloring occurs on your TV?

The center speaker is designed to be placed close to a TV, but the picture may be affected on some TVs and setup combinations. If this occurs, turn the TV off for about 30 minutes. The demagnetizing function of the TV should correct the problem. If it persists, move the speakers further away from the TV.

What should you do before connecting the equipment?

Turn off all equipment before connection and read the appropriate operating instructions. Do not connect the AC power supply cord until all other connections are completed.

What should you pay attention to when placing the speakers?

Pay attention to the type of speaker and the connector color when you place the speakers. Main unit (rear) Connect to the terminals of the same color. Use of the speaker cable stickers is convenient when making cable connections.

What should you do with the wires on the speakers?

Insert the wire fully, taking care not to insert beyond the wire insulation. i: White j: Blue line

What should you avoid doing with the speaker wires?

Be careful not to cross (short circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers.

What type of antenna should you use if radio reception is poor?

Use an FM outdoor antenna if radio reception is poor.

What are some cautions to keep in mind when connecting the speakers?

• The main unit and supplied speakers are to be used only as indicated in this setup. Failure to do so may lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance.
• Do not attempt to attach these speakers to walls using methods other than those described in this manual.

How do you connect the radio antenna?

Affix this end of the antenna to a wall or pillar where the reception is best.

How do you listen to the TV audio on the sound system?

To listen to the TV audio on the sound system, connect the optical digital audio cable, HDMI§ cable or audio cable. Refer to the operating instructions of the respective devices for the settings necessary to output the audio.

What is the benefit of using an HDMI connection?

This connection provides the best picture and audio quality.

What is VIERA Link “HDAVI Control”?

If your Panasonic TV is VIERA Link compatible, you can operate your TV synchronizing with home theater operations or vice versa ( 14, Linked operations with the TV).

What are some considerations when using HDMI cables?

• Use the High Speed HDMI Cables.
• Non-HDMI-compliant cables cannot be utilized.
• It is recommended that you use Panasonic’s HDMI cable. Recommended part number: RP-CDHS15 (1.5 m/4.9 ft), RP-CDHS30 (3.0 m/9.8 ft), RP-CDHS50 (5.0 m/16.4 ft), etc.
• Do not make the video connections through the VCR. Due to copy guard protection, the picture may not be displayed properly.
• After connecting with the optical digital audio cable or HDMI§ cable, make settings to suit the type of audio from your digital equipment ( 10). (Only Dolby Digital and PCM can be played with this connection.)

What is ARC?

ARC is an abbreviation of Audio Return Channel, also known as HDMI ARC. It refers to one of the HDMI functions. If the TV is ARC compatible, audio from the TV can be sent to this unit via the HDMI cable without the need to make an extra audio connection.

How do you connect with an ARC compatible TV?

• Refer to the operating instructions of the TV for details.
• Be sure to connect to the TV’s ARC compatible terminal. (Refer to the operating instructions for the TV.)

When should you use the alternative video connection to a TV?

Use this video connection if the TV’s HDMI input terminal is not available.

How do you connect a Set Top Box?

Use this connection when you want to output the original surround audio from your STB, etc. to this unit. Connect the optical digital audio cable (not supplied) from the DIGITAL AUDIO IN OPTICAL terminal on the main unit to the OPTICAL OUT terminal on your STB.

What should you do if the DIGITAL AUDIO IN OPTICAL terminal is already in use for the TV audio?

If the DIGITAL AUDIO IN OPTICAL terminal is already in use for the TV audio, reconnect the TV audio to the AUX terminal using an audio cable.

What should you do if you have various sound sources?

If you have various sound sources (such as Blu-ray Disc player, DVD recorder, VCR, etc.), connect them to the available inputs on the TV and the TV output should then be connected to the AUX, HDMI AV OUT§ or DIGITAL AUDIO IN OPTICAL terminal of the main unit.

How can you conserve power?

The main unit consumes a small amount of power, even when it is in standby mode (approx. 0.2 W). To save power when the unit is not to be used for a long time, unplug it from the household AC outlet. You will need to reset some memory items when plugging back the main unit.

Can you use the supplied AC power supply cord with other equipment?

The supplied AC power supply cord is for use with the main unit only. Do not use it with other equipment. Also, do not use cords from other equipment with the main unit.

How should you aim the remote control?

Aim at the remote control signal sensor ( 4), avoiding obstacles.

• Distance: Within approx. 7 m (23 ft)
• Angle: Within approx. 20° up and down, approx. 30° to the left and right

What is the function of the Easy setup screen?

The Easy setup screen assists you in making necessary settings.

Can you perform the Easy setup at any time?

You can perform this setup anytime by selecting “Easy setup” in the Setup menu. ( 17)

How does VIERA Link affect the Easy setup?

• If this unit is connected to a “HDAVI Control 3 or later” compatible TV via HDMI cable, the menu language and TV aspect information will be retrieved via VIERA Link.
• If this unit is connected to a “HDAVI Control 2” compatible TV via HDMI cable, the menu language information will be retrieved via VIERA Link.

What type of batteries should you use in the remote control?

Use alkaline or manganese batteries.

How do you prepare the TV for use with the unit?

Preparation Turn on your TV and select the appropriate video input mode (e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connection to this unit.

• To change your TV’s video input mode, refer to its operating instructions.
• This remote control can perform some basic TV operations ( 4).

How do you perform the Easy setup?

1. Press [Í]1 to turn on the unit. The Easy setup screen appears automatically.
2. Press \8 to select “Yes” and press [OK]8.
3. Follow the messages and make the settings with \8 and [OK]8.
   • Language: Select the language used on menu screen.
   • TV aspect: Select the aspect to suit your TV.
   • Speaker layout: Select “Surround layout (Recommended)” mode or “Front layout (Alternative)” mode according to your speaker layout ( 6, Positioning).
   • Speaker check: Listen to speaker output to confirm speaker connections.
   • Speaker output: Make surround sound setting for speaker output.
   • TV audio: Select the audio input connection from your TV.
     • For AUX connection ( 7): Select “AUX”.
     • For HDMI connection ( 7): Select “ARC”.
     • For DIGITAL AUDIO IN OPTICAL connection ( 7): Select “DIGITAL IN”.
       • This will be the TV audio setting for VIERA Link “HDAVI Control”. ( 14)
4. Press [OK]8 to finish the “Easy setup”.

How do you listen to the radio?

Select a radio broadcast.

1. Press [RADIO]4 to select “FM”.
2. Press [SEARCH6, SEARCH5]? to select the frequency.
   • To start automatic tuning, press and hold [SEARCH6, SEARCH5]? until the frequency starts scrolling. Tuning stops when a station is found.

How do you preset the radio channel?

1. While listening to the radio broadcast, press [OK]8.
2. While the frequency is flashing on the display, press the numbered buttons to select the channel.

What happens when another station is stored in the same channel preset?

A station previously stored is overwritten when another station is stored in the same channel preset.

How do you preset stations automatically?

1. Press [RADIO]4 to select “FM”.
2. Press [MENU]C to select “LOWEST” or “CURRENT”.
   • LOWEST: To begin auto preset with the lowest frequency (FM 87.9 or FM 87.5).
   • CURRENT: To begin auto preset with the current frequency.§
     • To change the frequency, refer to “Manual tuning and presetting”.
3. Press and hold [OK]8. Release the button when “FM AUTO” is displayed. The tuner starts to preset all the stations it can receive into the channels in ascending order.

How do you listen to a preset channel?

1. Press [RADIO]4 to select “FM”.
2. Press the numbered buttons to select the channel.
   • To select a 2-digit number e.g. 12: [S10]2 \ \
   • Alternatively, press [X, W]@.

How do you use the START menu?

You can select desired source, change the settings, access playback/ menus, etc., by using the START menu.

1. Press [START]B to show the START menu.
   • When using VIERA Link “HDAVI Control”, the TV also turns on when the START menu is displayed.
2. Press \8 to select an item and press [OK]8.
   • To exit, press [START]B.
3. Press \8 to make the setting and press [OK]8.

What are the options available when “Input select” is selected in the START menu?

You can select a desired source from the menu.

• DVD/CD ( 11), FM RADIO ( left), AUX§1 ( below), ARC§1 ( below), DIGITAL IN§1, 2 ( below), iPod ( 15)
  • §1 “(TV)” will appear beside “AUX”, “ARC” or “DIGITAL IN”, indicating the TV audio setting for VIERA Link “HDAVI Control” ( 14).
  • §2 “(STB)” will appear beside “DIGITAL IN”, indicating the STB audio setting for VIERA Link “HDAVI Control” ( 14).

What are the options available when “Setup” is selected in the START menu?

You can change the settings for this unit. ( 16)

What other items are available in the START menu?

Other selectable items The items that are displayed will vary depending on the media and source. When a disc is loaded, you can also access playback or menus from the START menu. e.g. [DVD-V]

How do you use the on-screen control panel?

When the on-screen control panel appears e.g. [DVD-V] (when “Playback Disc” is selected from the START menu) You can operate the playback with the indicated controls.

How do you select the source using the remote control?

Press To select

• [DVD]4: DVD/CD
• [iPod]4: IPOD ( 15)
• [EXT-IN, RADIO]4:

Each time you press the button:

• FM: ( left)
• AUX: For audio input through the AUX terminal.
• ARC: For audio input through the HDMI AV OUT terminal.
• D-IN: For audio input through the DIGITAL AUDIO IN OPTICAL terminal. ( 10)

How do you listen to the TV or other device’s audio from this unit’s speakers?

1. Preparation
   • Make sure that there is an audio connection between this unit and the TV or other device. ( 7)
   • Turn on the TV or/and other device.
2. Press [EXT-IN]4 to choose the source that is used to connect this unit to the TV or other device.
   • To change the surround sound effects and sound mode, refer to “Enjoying sound effects from all speakers” ( right).
   • If your Panasonic TV is VIERA Link compatible, refer to “Linked operations with the TV” ( 14) for other related functions.

What should you do after selecting the source?

Confirm the audio connection to the AUX, HDMI AV OUT or DIGITAL AUDIO IN OPTICAL terminal on the main unit when you select the corresponding sources ( 7). Reduce the volume on the TV to its minimum, and then adjust the volume of the main unit.

How do you make settings for digital audio input?

Select to suit the type of audio from the DIGITAL AUDIO IN OPTICAL and HDMI AV OUT terminal on the main unit. Underlined items are the factory presets.

1. Press [EXT-IN]4 several times to select “D-IN” or “ARC”.
2. Press [PLAY MODE]9 and then \8 to select the mode.
3. While the selected mode is displayed, press \8 to select the desired setting.

What are the available settings for digital audio input?

Mode	Setting
DUAL:	(Only works with Dolby Dual Mono) <ul> <li> MAIN+SAP (stereo audio) <li> MAIN <li> SAP <br> “SAP” = Secondary Audio Program <br> ≥ Set PCM FIX mode to “OFF” to listen to the “MAIN” or “SAP” audio.
DRC:	(Dynamic Range Compression) <ul> <li> ON: Adjust for clarity even when the volume is low by compressing the range of the lowest sound level and the highest sound level. Convenient for late night viewing. (Only works with Dolby Digital) <li> OFF: The full dynamic range of the signal is reproduced.
PCM FIX:	<ul> <li> ON: Select when receiving only PCM signals. <li> OFF: Select when receiving Dolby Digital and PCM signals. <br> ≥ When receiving true 5.1-channel surround sound, select “OFF”.
How do I enhance the audio effect for low volume 5.1-channel sound?

Press and hold [–W.SRD] to show the current setting. While the current setting is displayed, press [–W.SRD] to change the setting. ON, ——. OFF. This only works when “Surround layout (Recommended)” mode is selected in “Speaker layout.” This is effective when playing 5.1-channel sound or when DOLBY PLII/“S.SRD” is selected.

How do I adjust the speaker balance during playback?

1. Press [CH SELECT]F to select “L” or “R.”
2. While “L” or “R” is selected Press8 to adjust the speaker balance.

How do I adjust the speaker level during playback?

1. Press [CH SELECT]F to select the speaker. Each time you press the button: e.g. L# C# R# RS# LS# SW
2. While “C”, “RS”, “LS”, “SW” or “S” is selected Press8 (increase) or8 (decrease) to adjust the speaker level for each speaker. C, RS, LS, SW, S: `6 dB to i6 dB (L, R: Only the balance is adjustable.)

You can adjust SW (Subwoofer) only if the disc includes a subwoofer channel. What happens when “S” appears?

When “S” appears, only the surround speaker channel can be adjusted. Both surround speaker levels will be adjusted at the same time.

What are the basic controls?

• Stop: [∫ STOP]5 The position is memorized while “RESUME” is on the main unit’s display. [DVD-V] [VCD] [CD] This unit can memorize the resume position for the last 5 discs.

  • Press [1 PLAY]5 to resume.
  • Press [∫ STOP]5 again to clear the position.

• Pause: [; PAUSE]5

  • Press [1 PLAY]5 to restart play.

• Skip: [SKIP:, SKIP 9]5

• Search: [SEARCH6, SEARCH5]5 (during play)

• Slow-motion: [SEARCH6, SEARCH5]5 (during pause)

  • Search: Up to 4 steps
  • Slow-motion: Up to 3 steps
  • Press [1 PLAY]5 to start normal play.
  • [VCD] Slow-motion: Forward direction only.

• [DVD-V] [VCD] Frame-by-frame: [2;, ;1]8 (during pause)

  • [VCD] Forward direction only.

• On-screen item select: [3, 4, 2, 1, OK]8

  • 8: Select
  • [OK]8: Confirm

• Enter number: Numbered buttons [DVD-V] [VCD] [CD] e.g. To select 12: [S10]2

• [DVD-V] Show a disc top menu: [TOP MENU]7

• [DVD-V] Show a disc menu: [MENU]C

• Return to previous screen: [RETURN]D

• [VCD] (with playback control)

  • Show a disc menu: [RETURN]D
  • Turn PBC function on/off: [MENU]C

• Main unit display: [FL DISPLAY]E

  • [DVD-V] Time display ,-. Information display
  • [JPEG] SLIDE,-.Contents number

What do I do when I finish using the menus?

DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED. Press [∫ STOP]5 when you finish to preserve the unit’s motor and your TV screen.

How do I use the navigation menu?

Press8 to select an item and press [OK]8. Press8 to skip page by page.

How do I select the picture in Thumbnail menu?

1. While the picture is displayed, press [TOP MENU]7 to show the thumbnail menu.
2. Press8 to select a picture and press [OK]8. Press [SKIP:, SKIP 9]5 to skip page by page.

How do I rotate a picture?

While a picture is displayed, press8 to rotate the picture.

How do I use Program and Random play?

While stopped, press [PLAY MODE]9 to select the play mode. Each time you press the button:

• [CD] Music Program menu
• [JPEG] Picture Program menu
• RND (Random) menu
• Exit program and random menus

How do I clear the selected program?

1. Press8 and then press8 to select the program.
2. Press [CANCEL]3.

How do I clear the whole program?

Press8 several times to select “Clear All”, and then press [OK]8. The whole program is also cleared when the disc tray is opened, the unit is turned off or another source is selected.

How do I play all tracks in random order?

Press [1 PLAY]5 to start play.

How do I play the JPEG contents of the selected group in random order?

This works only when the elapsed play time can be displayed. It also works with all JPEG content. Items shown differ depending on the type of disc and playback mode. Random mode will be cleared when you change the repeat mode.

What does the total title number on iR/iRW do?

Total title number may not be displayed properly on iR/iRW.

How do I use Music Program?

1. Press8 to select an item and press [OK]8. When a content is selected, it will be programmed. Repeat this step to program other items. To return to the previous folder, press [RETURN]D. You can also do this by selecting “ ” in the menu.
2. Press [1 PLAY]5 to start play.

How do I use Picture Program?

1. Press8 to select an item and press [OK]8. When a content is selected, it will be programmed. Repeat this step to program other items. To return to the previous folder, press [RETURN]D. You can also do this by selecting “ ” in the menu.
2. Press [1 PLAY]5 to start play.

How do I use Random play?

1. Press8 to select the desired group and press [OK]8. To return to the previous folder, press [RETURN]D. You can also do this by selecting “ ” in the menu.
2. Press8 to select the desired content and press [OK]8. Play starts from the selected content.

How do I use Repeat play?

During play, press and hold [–REPEAT]9, to show the repeat mode. While the repeat mode is displayed, press [–REPEAT]9 to select the item to be repeated. e.g. [DVD-V] Chapter ---. Title —. `Off To cancel, select “Off”.

What is the maximum number of characters for file/folder name?

Maximum: 16 characters for file/folder name. Only the contents in the current group will be played.

How do I start from a specific item?

e.g. [DVD-V]: T2 C5 To select 12: [S10]2 [OK]8

How do I select the audio soundtrack?

[DVD-V] (with multiple soundtracks) To select audio soundtrack

How do I select “L”, “R”, “L+R” or “L R”?

Actual operations depend on the disc. Read the disc’s instructions for details.

How do I change the play speed?

[DVD-V] To change play speed – from “k0.6” to “k1.4” (in 0.1-unit steps) Press [1 PLAY]5 to return to normal play.

What are the considerations for changing the play speed?

• After you change the speed

  • Dolby Pro Logic II has no effect.
  • Audio output switches to 2-channel stereo.
  • Sampling frequency of 96 kHz is converted to 48 kHz.

• This function does not work with DTS source. The play speed will return to “k1.0”.

• This function may not work depending on the disc’s recording.

How do I use A-B Repeat (To repeat a specified section)?

Except [JPEG] Press [OK]8 at the starting and ending points. Select “Off” to cancel.

How do I select the subtitle language?

[DVD-V] (with multiple subtitles) To select subtitle language. On iR/iRW, a subtitle number may be shown for subtitles that are not displayed.

How do I select a video angle?

[DVD-V] (with multiple angles) To select a video angle

How do I select the method of conversion for video output to suit the type of material?

Auto, Video When the content is distorted, select “Video”. This may have no effect with some sources.

What are the Zoom options?

Normal, 1, 2, 3

How do I make the dialog in movies easier to hear?

[DVD-V] (Dolby Digital, DTS, 3-channel or higher, with the dialog recorded in the center channel) Off, On

What is the signal type/data?

LPCM/ D/DTS/MPEG: Signal type

How do I make the sound of the center speaker seem like it is coming from within the TV?

You can make the sound of the center speaker seem like it is coming from within the TV with Center Focus (C.FOCUS). It is effective when playing audio containing the center channel sound or when DOLBY PLII is selected. ON ,——. OFF

How do I adjust the amount of bass?

You can adjust the amount of bass with SUBW LVL (Subwoofer level). The unit automatically selects the most suitable setting according to the type of playback source. LEVEL 1 ,# LEVEL 2 ,# LEVEL 3 ,# LEVEL 4. The setting you make is retained and recalled every time you play the same type of source.

Each time you press \8, you can choose from the following sound effects:

• FLAT: Cancel (no effect is added).
• HEAVY: Adds punch to rock.
• CLEAR: Clarifies higher sounds.
• SOFT: For background music.

How do I prepare for displaying the picture?

To display the picture, turn on your TV and change its video input mode (e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connection to this unit. When you press [< OPEN/CLOSE]2 to close the disc tray, this unit automatically starts playing the disc in the tray. [JPEG] – Only the contents in the current group will be played.

How do I select my desired item to start play?

You can select your desired item to start play.

How do I use the functions?

1. Press [FUNCTIONS]6 to show the on-screen menu. Each time you press the button:

   • Menu 1 (Disc)
   • Menu 2 (Video)
   • Menu 3 (Audio)
   • Exit

2. Press8 to select the item and press [OK]8.

3. Press8 to make the settings and press [OK]8.

How do I use Track Search, Title Search, Content Search, Chapter Search?

To start from a specific item e.g. [DVD-V]: T2 C5 To select 12: [S10]2 \ \ [OK]8

How do I use Audio?

[DVD-V] (with multiple soundtracks) To select audio soundtrack [VCD] To select “L”, “R”, “L+R” or “L R” Actual operations depend on the disc. Read the disc’s instructions for details.

How do I use Repeat Mode?

(See “Repeat play”)

How do I use Subtitle?

[DVD-V] (with multiple subtitles) To select subtitle language On iR/iRW, a subtitle number may be shown for subtitles that are not displayed.

How do I use Angle?

[DVD-V] (with multiple angles) To select a video angle

How do I use Transfer Mode?

To select the method of conversion for video output to suit the type of material Auto, Video When the content is distorted, select “Video”. This may have no effect with some sources.

How do I use Zoom?

To select zoom Normal, 1, 2, 3

How do I use Dialog Enhancer?

To make the dialog in movies easier to hear [DVD-V] (Dolby Digital, DTS, 3-channel or higher, with the dialog recorded in the center channel) Off, On

How do I prepare to use HDAVI Control?

1. Confirm that the HDMI connection has been made.
2. Set “VIERA Link” to “On.” (The default setting is “On”.)
3. Set the “HDAVI Control” operations on the connected equipment (e.g., TV).
4. Turn on all “HDAVI Control” compatible equipment and select this unit’s input channel on the connected TV so that the “HDAVI Control” function will work properly.

Whenever the connection or settings are changed, repeat this procedure and reconfirm the points in “Setting the audio link.”

How do I set the audio link with the TV?

Select “AUX”, “ARC”§1 or “DIGITAL IN” for TV audio link. Refer to TV audio setting in Easy setup or “TV Audio” in HDMI menu. Confirm the TV audio connection to the AUX terminal (for “AUX”), HDMI AV OUT terminal (for “ARC”§1) or DIGITAL AUDIO IN OPTICAL terminal (for “DIGITAL IN”) on the main unit.

How do I set the audio link with the STB?

Select “D-IN” for STB audio link. Refer to STB setting in “Making settings for digital audio input”. Confirm the STB audio connection to the DIGITAL AUDIO IN OPTICAL terminal (for “D-IN”) on the main unit.

What is VIERA Link “HDAVI Control”?

VIERA Link “HDAVI Control”, based on the control functions provided by HDMI which is an industry standard known as HDMI CEC (Consumer Electronics Control), is a unique function that was developed and added. As such, its operation with other manufacturers’ equipment that supports HDMI CEC cannot be guaranteed.

What HDAVI Control function does this unit support?

This unit supports “HDAVI Control 5” function. “HDAVI Control 5” is the newest standard (current as of November, 2011) for Panasonic’s HDAVI Control compatible equipment. This standard is compatible with Panasonic’s conventional HDAVI equipment.

Where can I find operational details about VIERA Link function support?

Please refer to individual manuals for other manufacturers’ equipment supporting VIERA Link function.

What does the synchronized audio and video output function do?

(For “HDAVI Control 3 or later”) This function automatically provides synchronized audio and video output. (This works only when the source is “DVD/CD”, “AUX”§2, “ARC”§1, 2 or “D-IN”§2, 3.) When using “DVD/CD” as the source, set “Time Delay” in Video menu to “0ms/Auto.” Audio and video will automatically be set in sync.

When will the TV automatically switch the input channel and display the corresponding action?

When the following operations are performed, the TV will automatically switch the input channel and display the corresponding action. Additionally when the TV is off, the TV will automatically turn on:

• When play starts on the unit
• When an action that uses the display screen is performed (e.g., START menu)

What happens when the TV input changes to TV tuner mode or the STB input channel?

When you switch the TV input to TV tuner mode or the STB input channel, this unit will automatically switch to “AUX”§2, “ARC”§1, 2 or “D-IN”§2, 3.

What happens when you start disc play?

When you start disc play, the TV will automatically switch its input mode for this unit.

What happens when all connected equipment compatible with “HDAVI Control”, including this unit, is turned off?

All connected equipment compatible with “HDAVI Control”, including this unit, automatically turn off when you switch the TV off. To continue audio playback even when the TV is turned off, select “Video” (“Power Off Link” in HDMI menu).

What happens when you press [Í]1?

When you press [Í]1, only this unit turns off. Other connected equipment compatible with VIERA Link “HDAVI Control” stays on. For details, refer also to the operating instructions for your TV.

How do I select whether audio will output from this unit’s speakers or the TV speakers?

You can select whether audio will output from this unit’s speakers or the TV speakers by using the TV menu settings. For details, refer to the operating instructions for your TV.

What happens when Home Theater mode is active?

This unit’s speakers are active.

• When you turn on this unit, this unit’s speakers will be automatically activated.
• When this unit is in standby mode, changing the TV speakers to this unit’s speakers in the TV menu will automatically turn this unit on and select “AUX”§2, “ARC”§1, 2 or “D-IN”§2, 3 as the source.
• The TV speakers are automatically muted.
• You can control the volume setting using the volume or mute button on the TV’s remote control. (The volume level is displayed on the main unit’s display.)
• To cancel muting, you can also use this unit’s remote control.
• If you turn off this unit, TV speakers will be automatically activated.

What happens when TV mode is active?

TV speakers are active.

• The volume of this unit is set to “0”.

  • This function works only when “DVD/CD”, “AUX”§2, “ARC”§1, 2 or “D-IN”§2, 3 is selected as the source on this unit.

What happens when switching between this unit speakers and TV speakers?

When switching between this unit speakers and TV speakers, the TV screen may go blank for several seconds.

What is VIERA Link “HDAVI Control”?

VIERA Link is a new name for EZ Sync. VIERA Link “HDAVI Control” is a convenient function that offers linked operations of this unit, and a Panasonic TV (VIERA) under “HDAVI Control”. You can use this function by connecting the equipment with the HDMI cable. See the operating instructions for connected equipment for operational details.

What does the playback menus function do?

(For “HDAVI Control 2 or later”) You can control the playback menus of this unit with the TV’s remote control. When operating the TV’s remote control, refer to the below illustration for operation buttons. You can operate the playback with the indicated controls.

What are the considerations for using the playback menus function?

• The on-screen control panel can also be shown by using a button on the TV’s remote control (e.g. [SUB MENU]).

  • This works only during “DVD/CD” playback and resume modes or, while the iPod music playback screen is displayed on the TV.

• Depending on the menu, some button operations cannot be performed from the TV’s remote control.

• You cannot input numbers with the numbered buttons on the TV’s remote control ( to). Use this unit’s remote control to select the play list etc.

What does the iPod/iPhone music function do?

You can enjoy iPod/iPhone music through this unit’s speakers.

What should I do before connecting/disconnecting the iPod/iPhone?

Before connecting/disconnecting the iPod/iPhone, turn the main unit off or reduce the volume of the main unit to its minimum. Play starts from the selected song.

How do I use Shuffle mode?

Press [PLAY MODE]9 several times. SHUFFLE SONGS, SHUFFLE ALBUMS, SHUFFLE OFF

How do I use Repeat mode?

Press and hold [–REPEAT]9 and then press the button several times within a few seconds. ONE REPEAT, ALL REPEAT, REPEAT OFF

What happens to the music playback modes set on the iPod/iPhone?

Music playback modes set on the iPod/iPhone will be maintained when connected to the main unit. Changes made while the iPod/iPhone is connected to the main unit will be kept on the iPod/iPhone after disconnecting it.

How do I recharge the battery?

• Recharging during standby mode: Ensure that the iPod/iPhone battery starts recharging before switching the main unit to standby mode.
• “IPOD ¢” will be shown on the main unit’s display during iPod/iPhone charging in main unit standby mode.
• Check iPod/iPhone to see the battery charging condition.
• If you are not using iPod/iPhone for an extended period of time after recharging has completed, disconnect it from main unit, as the battery will be depleted naturally. (Once fully recharged, additional recharging will not occur.)

How do I use the iPod/iPhone?

1. Connect the iPod/iPhone. To purchase this cable, consult your iPod/iPhone dealer.
2. Select this unit’s operation menu by using the TV menu settings. (For details, refer to the operating instructions for your TV.) The START menu will be shown. The START menu can also be shown by using a button on the TV’s remote control (e.g. [SUB MENU]). When “DVD/CD” is selected as the source, the TV’s remote control works only during stop mode. This feature does not work while the iPod music playback screen is displayed on the TV.
3. Select the desired item on the START menu.
4. When the on-screen control panel appears, press \8 to select an item and press [OK]8. Press \8 to skip page by page. To return to the previous screen, press [RETURN]D.

What are the basic controls for the iPod/iPhone?

Button	Function
[1 PLAY]5	Play
[∫ STOP]5, [; PAUSE]5	Pause
[SKIP:, SKIP 9]5	Skip (press and hold)
[SEARCH6, SEARCH5]5	Search

What are the considerations for iPod/iPhone compatibility?

• iPod/iPhone compatibility is based on the operations§ described in this manual.

  • Subject to the availability of the functions on your iPod/iPhone.

• Compatibility depends on the software version of your iPod/iPhone.

What should I do if reception status of an iPhone is poor when it is connected to this unit?

In some locations, reception status of an iPhone may be poor when it is connected to this unit.

How do I use the iPod touch/iPhone features?

1. Press the Home button on the iPod touch/iPhone.
2. Select the iPod touch/iPhone features on the touch screen to operate.

What happens when the iPhone receives a call while connected to this unit?

When the iPhone receives a call while connected to this unit, playback, etc. of the iPhone may stop. To prioritize the operation with the iPhone connected to this unit, make the setting so that the iPhone does not receive calls.

What are the compatible iPod/iPhone models?

• iPod touch®: 1st, 2nd, 3rd, and 4th generation
• iPod nano®: 1st, 2nd, 3rd, 4th, 5th, and 6th generation
• iPod classic®
• iPod®: 5th generation
• iPhone® 4S, iPhone® 4, iPhone® 3GS, iPhone® 3G, iPhone®

How do I change the player settings?

1. Press [DVD]4 to select “DVD/CD”.
2. Press [START]B to show the START menu.
3. Press8 to select “Setup” and press [OK]8.
4. Press8 to select menu and press [OK]8.
5. Press8 to select the item and press [OK]8.
6. Press8 to make the settings and press [OK]8. The settings remain intact even if you switch the unit to standby.

How do I choose the language for the on-screen messages?

English, Français, Español

How do I choose the audio language?

English, French, Spanish. Some discs start in a certain language despite any changes you make here. When the selected language is not available on the disc, the default language is played. There are discs where you can only switch the language from the menu screen.

How do I choose the subtitle language?

Auto, English, French, Spanish, Off. Some discs start in a certain language despite any changes you make here. When the selected language is not available on the disc, the default language is played. There are discs where you can only switch the language from the menu screen.

How do I choose the language for disc menus?

English, French, Spanish. Some discs start in a certain language despite any changes you make here. When the selected language is not available on the disc, the default language is played. There are discs where you can only switch the language from the menu screen.

How do I choose the setting to suit my TV?

• 16:9: Widescreen TV (16:9)
• 4:3 Pan&Scan: Regular aspect TV (4:3) The sides of the widescreen picture are cut off so it fills the screen (unless prohibited by the disc).
• 4:3 Letterbox: Regular aspect TV (4:3) Widescreen picture is shown in the letterbox style.

When should I adjust Time Delay?

When connected with a Plasma display, adjust if you notice the audio is out of sync with the video. 0ms/Auto, 20ms, 40ms, 60ms, 80ms, 100ms. When using VIERA Link “HDAVI Control” with “HDAVI Control 3 or later” compatible TV, select “0ms/Auto”. Audio and video will automatically be set in sync.

How do I select suitable picture quality for my TV?

This works only when the HDMI connection is being used. Select suitable picture quality for your TV. (Video recordings will be converted to, and output as, high-definition video.) Auto, 480i, 480p, 720p, 1080i, 1080p. Ensure that your TV can support the resolution that you choose. If a message screen appears, confirm your selection by pressing8 to select “Yes” and press [OK]8. If the picture is distorted, wait for 15 seconds or press8 to select “No”. To accept the setting, select “Yes” again.

How do I enable HD JPEG playback?

[JPEG] (This works only when using HDMI connection with “Video Resolution” set to “Auto”, “720p”, “1080i” or “1080p”.) On: HD JPEG playback is available. (JPEG images will be displayed in original resolution.) Off During HD JPEG playback, there will be no on-screen menus and on-screen displays.

How do I change the black level of the picture?

(This works only for video output from the VIDEO OUT terminal.) Lighter, Darker

How do I select the digital output?

Select to suit the type of equipment you connected to the HDMI AV OUT terminal. Select “Bitstream” when the equipment can decode the bitstream (digital form of 5.1-channel data). Otherwise, select “PCM”. (If the bitstream is output to the equipment without a decoder, high levels of noise can be output and may damage your speakers and hearing.) When audio output is from HDMI AV OUT terminal, and the connected equipment does not support the item selected, the actual output will depend on the performance of this connected equipment.

How do I set a rating level to limit DVD-Video play?

1 to 7, 8 No Limit. When you select your ratings level, a password screen is shown. The default password is “0000”. Enter the 4-digit password with the numbered buttons, and press [OK]8. You can change the default password. Do not forget your password. A message screen will be shown if a DVD-Video disc exceeding the rating level is inserted in the unit. Follow the on-screen instructions.

How do I change the password for “Ratings”?

When you change the password for the first time: The default password is “0000”. Follow the on-screen instructions.

How do I return all values in the Setup menu to the default settings except the password and ratings level?

Press8 to select “Yes” and press [OK]8. Turn the unit off and on again.

How do I adjust for clarity even when the volume is low?

On: Adjusts for clarity even when the volume is low. Convenient for late night viewing. (Only works with Dolby Digital) Off: The full dynamic range of the signal is reproduced.

How do I select the delay time of the speakers?

(Effective only when “Surround layout (Recommended)” mode is selected in “Speaker layout.”) (Center and surround speakers only) For optimum listening with 5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating position. If you have to place the center or surround speakers closer to the seating position, adjust the delay time to make up for the difference.

If either distance a or b is less than c, find the difference in the table and change to the recommended setting.

a Center speaker	Difference (Approx.)	Setting	b Surround speaker	Difference (Approx.)	Setting
30 cm (1 foot)	1ms		150 cm (5 feet)	5ms
60 cm (2 feet)	2ms		300 cm (10 feet)	10ms
90 cm (3 feet)	3ms		450 cm (15 feet)	15ms
120 cm (4 feet)	4ms
			150 cm (5 feet)	5ms

How do I select the delay time for my center speaker?

C Delay (Center Delay): 0ms, 1ms, 2ms, 3ms, 4ms, 5ms

How do I select the delay time for my surround speakers?

LS/RS Delay (Left Surround/Right Surround Delay): 0ms, 5ms, 10ms, 15ms

How do I use the test tone to listen to the speaker output to confirm speaker connections?

Test Tone: Use the test tone to listen to the speaker output to confirm speaker connections. Test tone will be output to each channel in the following order. Left, Center, Right, Surround Right, Surround Left, Subwoofer To stop the test tone, press [RETURN]D.

How do I enable the VIERA Link “HDAVI Control” function?

On: The VIERA Link “HDAVI Control” function is available.

When is audio output from the HDMI AV OUT terminal?

On: When audio output is from the HDMI AV OUT terminal. (Depending on the capabilities of the connected equipment, audio output may differ from the audio settings of the main unit.)

When is audio output NOT from the HDMI AV OUT terminal?

Off: When audio output is not from the HDMI AV OUT terminal. (The audio is output using the settings of the main unit.)

What message appears on the TV or unit’s display when the operation is prohibited by the unit or disc?

“/”

What message appears on the TV or unit’s display when you attempt to play a DVD-Video disc that does not have the same region number as the one on the rear panel of this unit?

“/ Incorrect Disc Region”

What message appears on the TV or unit’s display when the following occurs:

• You inserted a disc the unit cannot play.
• You inserted a blank disc.
• You inserted a disc that has not been finalized.

“NO PLAY”

What message appears on the TV or unit’s display when the following occurs:

• You have not inserted a disc.
• You have not inserted the disc correctly.

“NO DISC”

What message appears on the TV or unit’s display when the iPod/iPhone is drawing too much power?

“IPOD OVER CURRENT ERROR”

What should you do when you receive the following message on your TV or unit’s display, “IPOD OVER CURRENT ERROR”?

Remove the iPod/iPhone, and turn the unit off and on again.

What message appears on the TV or unit’s display when you need to check and correct the speaker cable connections?

“F61”

What should you do if you receive the following message on your TV or unit’s display, “F61”?

Check and correct the speaker cable connections. If this does not fix the problem, consult the dealer.

What message appears on the TV or unit’s display when there is a power supply problem?

“F76”

What should you do if you receive the following message on your TV or unit’s display, “F76”?

Consult the dealer.

What message appears on the TV or unit’s display when the disc may be dirty?

“DVD U11”

What should you do if you receive the following message on your TV or unit’s display, “DVD U11”?

Wipe the disc clean.

What message appears on the TV or unit’s display when the stations are set and the radio tunes to the last preset station?

“SET OK”

What message appears on the TV or unit’s display when the following occurs:

• Incorrect operation performed.
• “ERROR” is displayed when automatic presetting is unsuccessful.

“ERROR”

What should you do if you receive the following message on your TV or unit’s display, “ERROR”?

≥ Incorrect operation performed. Read the instructions and try again. ≥ “ERROR” is displayed when automatic presetting is unsuccessful. Preset the stations manually.

What message appears on the TV or unit’s display when receiving stereo broadcasting?

“TUNED/STEREO”

What message appears on the TV or unit’s display when receiving monaural broadcasting or monaural sound is selected?

“TUNED”

What message appears on the TV or unit’s display when trouble may have occurred?

“DVD H∑∑” “DVD F∑∑∑”

What do the ∑ stand for in the messages “DVD H∑∑” “DVD F∑∑∑”?

The ∑ stands for a number. The numbers following “H” and “F” depend on the status of the unit.

What should you do if you receive the following message on your TV or unit’s display, “DVD H∑∑” “DVD F∑∑∑”?

Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC power supply cord, and then reconnect it.

What should you do if the service numbers fail to clear?

Note the service number and contact a qualified service person.

What message appears on the TV or unit’s display when the HDMI connection acts unusually?

“U70∑”

What do the ∑ stand for in the message “U70∑”?

The ∑ stands for a number. The actual number following “U70” will depend on the state of the main unit.

What are the possible reasons why the HDMI connection acts unusually?

• The connected equipment is not HDMI-compatible.
• Use the High Speed HDMI Cables.
• The HDMI cable is too long.
• The HDMI cable is damaged.

What message appears on the TV or unit’s display when you need to match the modes on the main unit and remote control?

“REMOTE 1” or “REMOTE 2”

What should you do if you receive the following message on your TV or unit’s display, “REMOTE 1” or “REMOTE 2”?

Match the modes on the main unit and remote control. Depending on the number being displayed (“1” or “2”), press and hold [OK]8 and the corresponding numbered button (\ or ) for at least 2 seconds.

What message appears on the TV or unit’s display while loading?

“LOADING”

What is the RMS Output Power per channel for the following in Dolby Digital Mode:

• Front Ch
• Surround Ch
• Center Ch

160 W per channel (3 Ω), 1 kHz, 10 % THD

What is the RMS Output Power per channel for the Subwoofer Ch in Dolby Digital Mode?

200 W per channel (3 Ω), 100 Hz, 10 % THD

What is the Total RMS Dolby Digital mode power?

1000 W

What is the FTC Output Power per channel for the following in Dolby Digital Mode:

• Front Ch
• Surround Ch

60 W per channel (3 Ω), 150 Hz to 20 kHz, 1 % THD

What is the FTC Output Power per channel for the Center Ch in Dolby Digital Mode?

90 W per channel (3 Ω), 150 Hz to 20 kHz, 1 % THD

What is the FTC Output Power per channel for the Subwoofer Ch in Dolby Digital Mode?

100 W per channel (3 Ω), 50 Hz to 150 Hz, 1 % THD

What is the Total FTC Dolby Digital mode power?

430 W

How many preset memories are there for the FM Tuner?

30 stations

What is the Frequency range for Frequency Modulation (FM) in the following steps:

• 200-kHz step

• 100-kHz step

• 87.9 MHz to 107.9 MHz

• 87.5 MHz to 108.0 MHz

What is the impedance for the Antenna terminals?

75 Ω (unbalanced)

What are the sampling frequencies for the Optical digital input?

32 kHz, 44.1 kHz, 48 kHz

What size discs can be played in the unit?

8 cm (3˝) or 12 cm (5˝)

What types of discs can be played in the unit?

• (1) DVD (DVD-Video)
• (2) DVD-R (DVD-Video, JPEG§2, 3)
• (3) DVD-R DL (DVD-Video)
• (4) DVD-RW (DVD-Video, JPEG§2, 3)
• (5) +R/+RW (Video)
• (6) +R DL (Video)
• (7) CD, CD-R/RW (CD-DA, Video CD, SVCD§1, JPEG§2, 3)

**What are the following: **

• §1

• §2

• §3

• Conforming to IEC62107

• Exif Ver 2.1 JPEG Baseline files Picture resolution: 16:9 min. size 480×480, max. size (720×480)x(405×480); 4:3 min. size 480×480, max. size (720×480)x(540×480)

• The total combined maximum number of recognizable picture contents and groups: 2600 picture contents and 259 groups. (Excluding Root folder)

What is the Pick up Wavelength (DVD/CD)?

655/790 nm

What is the Laser power?

CLASS II/CLASS IIa

What is the Number of channels for the Audio output (Disc)?

5.1 ch (FL, FR, C, SL, SR, SW)

What is the Video system?

NTSC

What is the Output level and Terminal for the Composite video output?

• Output level: 1 Vp-p (75 Ω)
• Terminal: Pin jack (1 system)

What is the Terminal for the HDMI AV output?

19-pin type A connector

What HDAVI Control function does this unit support?

“HDAVI Control 5” function

What are the Surround speakers’ specifications?

• Type: 1 way, 1 speaker system (Bass reflex)
• Speaker unit(s): Full range 6.5 cm (2 1/2˝) Cone type
• Impedance: 3 Ω
• Output sound pressure: 78 dB/W (1 m)
• Frequency range: 97 Hz to 25 kHz (-16 dB) 130 Hz to 22 kHz (-10 dB)
• Dimensions (WxHxD): 80 mm x 139 mm x 70 mm (3 5/32˝ x 5 15/32˝ x 2 3/4˝)
• Mass [Weight]: 0.37 kg (0.82 lbs)

What are the Center speaker’s specifications?

• Type: 1 way, 1 speaker system (Bass reflex)
• Speaker unit(s): Full range 6.5 cm (2 1/2˝) Cone type
• Impedance: 3 Ω
• Output sound pressure: 79 dB/W (1 m)
• Frequency range: 90 Hz to 25 kHz (-16 dB) 130 Hz to 22 kHz (-10 dB)
• Dimensions (WxHxD): 146.5 mm x 84 mm x 78 mm (5 15/16˝ x 3 5/16˝ x 3 1/16˝)
• Mass [Weight]: 0.5 kg (1.1 lbs)

What are the Subwoofer’s specifications?

• Type: 1 way, 1 speaker system (Bass reflex)
• Speaker unit(s): Woofer 16 cm (6 1/2˝) Cone type
• Impedance: 3 Ω
• Output sound pressure: 78 dB/W (1 m)
• Frequency range: 40 Hz to 220 Hz (-16 dB) 45 Hz to 180 Hz (-10 dB)
• Dimensions (WxHxD): 145 mm x 289.5 mm x 259 mm (5 23/32˝ x 11 13/32˝ x 10 3/16˝)
• Mass [Weight]: 3 kg (6.6 lbs)

What is the Power supply?

AC 120 V, 60 Hz

What is the Power consumption for the main unit?

75 W

What are the main unit’s Dimensions (WxHxD)?

430 mm x 47 mm x 263 mm (16 15/16˝ x 1 27/32˝ x 10 11/32˝)

What is the main unit’s Mass [Weight]?

2.4 kg (5.3 lbs)

What is the Operating temperature range?

0 °C to 40 °C (32 °F to 104 °F)

What is the Operating humidity range?

35 % to 80 % RH (no condensation)

What is the Power consumption in standby mode?

approx. 0.2 W

Where can you find the model number and serial number of this product?

On either the back or the bottom of the unit.

What should you do if you see this symbol outside the European Union?

This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

What does the ENERGY STAR® symbol mean?

As an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

What does the FCC Note state about this product?

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

What should a user do if this equipment causes harmful interference to radio or television reception?

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

What would void the user’s authority to operate this device?

Any unauthorized changes or modifications to this equipment.

What Part of the FCC Rules does this device comply with?

Part 15

What are the two conditions for operation of this device?

• (1) This device may not cause harmful interference, and
• (2) this device must accept any interference received, including interference that may cause undesired operation.

Who is the Responsible Party for this product?

Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094

Who is the Support Contact for this product?

Panasonic Consumer Marketing Company of North America Telephone No.: 1-800-211-PANA (7262)