PANASONIC PT-RZ21K (02) PDF Document

1. Open the cover by pressing the guide and lifting it.
2. Insert the batteries making sure the polarities are correct (insert the minus side first).
3. Close the cover.

When removing the batteries, perform the steps in reverse order.

When using multiple projectors, you can operate them individually or simultaneously by setting ID numbers.

1. Press the ID SET button on the remote control.
2. Within five seconds, press and set the one-digit or two-digit ID number set on the projector body using the number (0 – 9) buttons.

If you press the ID ALL button, you can control the projectors regardless of the ID number setting of the projector body.

Note: Replace the projection lens after turning off the power of the projector.

1. Loosen the screw fixing the lens hole cover using a Phillips screwdriver (turn counterclockwise until it turns freely).
2. Remove the lens hole cover by pressing the lens release button and turning the cover counterclockwise until the mark on the cover aligns with the mark on the projector (to the left of LOCK).
3. Insert the projection lens by aligning the mark on the projection lens (orange) with the mark on the projector (to the left of LOCK) and turn clockwise until it clicks.
4. Secure the projection lens with the supplied lens fixing screw using a Phillips screwdriver in screw hole A located to the right of the mark on the lens.

1. Remove the lens fixing screw using a Phillips screwdriver.
2. Remove the projection lens by turning it counterclockwise while pressing the lens release button. Turn untill the mark on the lens aligns with the mark on the projector.
3. Attach the supplied lens hole cover by aligning the marks and turning clockwise until it clicks.
4. Secure the lens hole cover with the screw.

For India models: Check the shapes of the AC IN terminal and connector, insert completely. To remove, confirm the MAIN POWER switch is OFF, remove from outlet, then remove from projector while pressing the lock button.

For other countries/regions:

1. Confirm the power cord holder is raised.
2. Check shapes and insert the connector completely.
3. Lower the power cord holder so it snaps onto the power cord to fix it.

1. Connect the power cord to the projector and an outlet.
2. Press the ON side of the MAIN POWER switch to turn on the power. The power indicator will light in red (standby mode).
3. Press the power on button on the remote control or control panel. The power indicator will light in green and the image will be projected.

1. Press the power standby button. The “POWER OFF(STANDBY)” confirmation screen will display.
2. Press the left/right arrow buttons to select OK and press ENTER (or press the power standby button again).
3. Projection stops and the power indicator lights in orange (fan running). Wait until the indicator lights in red (fan stopped).
4. Press the OFF side of the MAIN POWER switch to turn off the power.

You can switch the input by pressing the specific input selection button on the remote control or control panel:

• RGB1: Switches to RGB1 input.
• RGB2: Switches to RGB2 input.
• DIGITAL LINK: Switches to DIGITAL LINK input.
• DVI-D: Switches to DVI-D input.
• HDMI: Switches to HDMI input.
• SDI 1/2: Switches between SDI1 and SDI2 input.

Alternatively, press the INPUT MENU button to display the input selection list on screen, select the desired input with arrow keys, and press ENTER.

Using the Control Panel:

1. Press the LENS button. Pressing it cycles through FOCUS, ZOOM, and SHIFT adjustment screens.
2. Select the item and use the arrow buttons to adjust.

Using the Remote Control:

1. Press the FOCUS, ZOOM, or SHIFT buttons.
2. Use the arrow buttons to adjust.

Press the SHUTTER button on the remote control or control panel to temporarily turn off the image. Press the button again to display the image.

1. Press the MENU button to display the MAIN MENU.
2. Press the up/down arrow buttons to select an item from the main menu (e.g., PICTURE, POSITION).
3. Press the ENTER button to display the sub-menu.
4. Press the up/down arrow buttons to select a sub-menu item.
5. Press the left/right arrow buttons or ENTER to change or adjust settings.

Select GEOMETRY from the POSITION menu. You can choose from the following options:

• KEYSTONE: Adjusts trapezoidal distortion (Vertical/Horizontal).
• CORNER/PINCUSHION: Adjusts distortion in the four corners or pincushion distortion.
• CURVED CORRECTION: Adjusts curved distortion.

1. Connect the projector to a computer or hub using a LAN cable via the DIGITAL LINK/LAN terminal.
2. Turn on the projector and press the MENU button.
3. Select NETWORK and then NETWORK SETUP.
4. Configure settings such as DHCP (ON/OFF), IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY.
5. Select STORE and press ENTER, then select OK.

Wipe off dirt and dust from the front surface of the lens with a soft clean cloth. Do not use a cloth that is fluffy, dusty, or soaked with oil/water. Since the lens is fragile and made of glass, do not use excessive force when wiping to avoid scratching the surface.

• Is the lens focus set correctly?
• Is the projection distance appropriate?
• Is the lens dirty?
• Is the projector installed perpendicular to the screen?

• Are connections to external devices correctly performed?
• Is the image input selected correctly?
• Is the BRIGHTNESS adjustment setting at a minimum?
• Is the shutter function in use?
• Is the projection lens attached correctly?
• Is the lens cover still attached to the lens?

1. Go to the P IN P menu and select P IN P MODE.
2. Select a USER mode (USER1 – USER3).
3. Select MAIN WINDOW or SUB WINDOW and choose the input terminal for each.
4. Adjust SIZE (10-100%) and POSITION.
5. Note: P IN P may not be available for some signal combinations (e.g., DIGITAL LINK and other inputs cannot be combined).

Select PROJECTOR SETUP from the main menu, then select INITIALIZE. You can choose:

• ALL USER DATA: Returns all settings including registered signals and network settings to factory default.
• REGISTERED SIGNAL: Deletes saved setting values for input signals.
• NETWORK/E-MAIL: Returns network and email settings to default.
• LOGO IMAGE: Deletes registered user logo.