PANASONIC PT-MZ570 (01) PDF Document

To quickly set up and use your PANASONIC PT-MZ570 projector, follow these steps:

1. Set up the projector.

2. Connect with external devices.

3. Connect the power cord.

4. Switch on the projector.

5. Make initial settings (this step is for when you switch on the power for the first time after purchasing the projector).

6. Select the input signal.

7. Adjust the image.

The PANASONIC PT-MZ570 comes with the following accessories:

• Wireless/wired remote control unit (1)

• Power cord (Quantity and type vary by region)

• CD-ROM (1) (Operating Instructions are included)

• AAA/R03 or AAA/LR03 battery (2) (For remote control unit)

• Lens cover (1) (Only models with lens)

The following optional accessories are available for the PANASONIC PT-MZ570:

To prepare the remote control for your PANASONIC PT-MZ570, you need to insert the batteries:

1. Open the cover on the back of the remote control by pressing the guide and lifting it.

2. Insert the two AAA batteries, making sure to align the + and – terminals correctly. Insert the negative (–) side first.

3. Close the cover.

To remove the batteries, perform these steps in reverse order.

When using multiple PANASONIC PT-MZ570 projectors together, you can operate them all simultaneously or each one individually by assigning a unique ID number to each projector.

1. After completing the initial settings for the projectors, set a unique ID number (from 1 to 64) for each projector body in the [PROJECTOR SETUP] menu → [PROJECTOR ID].

2. On the remote control, press the button.

3. Within five seconds, use the number buttons (0-9) to enter the ID number corresponding to the projector you wish to control.

4. To control all projectors simultaneously, press the button on the remote control. This will control all projectors regardless of their assigned ID numbers.

The factory default ID number for both the projector and remote control is [ALL].

To use the remote control as a wired remote, connect the remote control’s wired terminal to the terminal on the PANASONIC PT-MZ570 using a commercially available M3 stereo mini plug cable. This is useful in locations with obstacles or strong ambient light. The wireless function is disabled when a cable is connected to the terminal.

The PANASONIC PT-MZ570 projector has several installation modes. You can set them in the [PROJECTOR SETUP] menu → [PROJECTION METHOD].

Setting on a desk/floor and projecting forward:

• [FRONT/REAR]: Set to [FRONT]

• [FLOOR/CEILING]: Set to [AUTO] or [FLOOR]

Setting on a desk/floor and projecting from rear (with a translucent screen):

• [FRONT/REAR]: Set to [REAR]

• [FLOOR/CEILING]: Set to [AUTO] or [FLOOR]

Mounting on the ceiling and projecting forward:

• [FRONT/REAR]: Set to [FRONT]

• [FLOOR/CEILING]: Set to [AUTO] or [CEILING]

Mounting on the ceiling and projecting from rear (with a translucent screen):

• [FRONT/REAR]: Set to [REAR]

• [FLOOR/CEILING]: Set to [AUTO] or [CEILING]

Portrait setting and projecting forward:

• [FRONT/REAR]: Set to [FRONT]

• [FLOOR/CEILING]: Set according to the image you want to project.

Portrait setting and projecting from rear (with a translucent screen):

• [FRONT/REAR]: Set to [REAR]

• [FLOOR/CEILING]: Set according to the image you want to project.

The projector has a built-in angle sensor that automatically detects its orientation when [FLOOR/CEILING] is set to [AUTO].

To adjust the projection angle of the PANASONIC PT-MZ570, install it on a flat surface. If the screen is tilted, you can extend the front adjustable feet to make the projected image rectangular. The feet can also be used to level the projector horizontally.

To extend the feet, turn them as shown in the manual’s diagram. To retract them to their original position, turn them in the opposite direction. The maximum adjustment range for each foot is 23 mm (29/32″).

To remove the projection lens from your PANASONIC PT-MZ570, follow these steps:

1. Ensure the projector is turned off and the lens is moved to the home position.

2. Loosen the top slide cover fixing screw with a Phillips screwdriver until it turns freely.

3. Slide the top slide cover open.

4. While pressing the lens release lever, turn the projection lens counterclockwise to the end.

5. Remove the projection lens from the projector body.

Store the removed lens in a place free from vibration and impact.

To attach a projection lens to your PANASONIC PT-MZ570, follow this procedure:

1. Align the mark (red dot) on the projection lens with the corresponding mark (red dot) on the projector body.

2. Insert the lens all the way into the projector.

3. Turn the projection lens clockwise until it locks into place.

After attaching, gently turn the lens counterclockwise to confirm that it is securely locked and does not come out.

To attach the optional Wireless Module (Model No.: ET-WM300) to your PANASONIC PT-MZ570, follow these steps:

1. Turn off the power to the projector following the correct shutdown procedure.

2. Loosen the top slide cover fixing screw with a Phillips screwdriver until it turns freely.

3. Slide the top slide cover until the attachment line is visible, and then remove the cover.

4. Insert the Wireless Module into the wireless module connection terminal inside the projector.

5. Confirm that the edge of the Wireless Module is aligned with the wireless module attachment line.

6. Securely fix the Wireless Module with the fixing screw supplied with the module.

7. Re-attach the top slide cover by aligning it to the attachment line and sliding it into place.

8. Securely tighten the top slide cover fixing screw with a Phillips screwdriver.

How to attach the power cord:

1. Ensure the

Switching on the projector:

1. Connect the power cord to the projector and then plug it into a wall outlet.

2. Press the side of the

When you switch on the PANASONIC PT-MZ570 for the first time, an initial setting screen is displayed. Follow these steps:

1. Focus Adjustment: A focus adjustment screen appears first. Use the arrow buttons to adjust the focus so the menu screen is clear. Press the

You can switch the input image to project on your PANASONIC PT-MZ570 using one of two methods:

Directly with the remote control:

Press the input selection button for the desired source on the remote control (, , , ,

Using the input selection screen:

1. Press the button on the control panel.

2. The input selection screen will be displayed.

3. Use the up/down arrow buttons to select the input you want to project.

4. Press the button to confirm.

You can adjust the focus, zoom, and lens shift on your PANASONIC PT-MZ570 using either the remote control or the control panel.

Using the remote control:

1. Press the specific lens button for the adjustment you want to make: , , or .

2. Use the arrow buttons (up, down, left, right) to make the adjustment.

• For FOCUS and ZOOM, typically up/down arrows are used.

• For SHIFT, all four arrow buttons are used to move the image position vertically and horizontally.

Using the control panel:

1. Press the button. Pressing the button repeatedly will cycle through the adjustment screens for [FOCUS], [ZOOM], and [SHIFT].

2. Once the desired adjustment screen is displayed, use the arrow buttons to make the adjustment.

The shutter function allows you to temporarily turn off the image and audio from the PANASONIC PT-MZ570.

1. Press the button on the remote control or the control panel. The image and audio will disappear.

2. To resume projection, press the button again. The image and audio will reappear.

While the shutter is closed, the power indicator will blink slowly in green.

Before performing any maintenance on your PANASONIC PT-MZ570, make sure to turn it off and disconnect the power plug from the outlet.

Outer case:

Wipe off dirt and dust with a soft, dry cloth. For persistent dirt, soak a cloth with water, wring it thoroughly, wipe the case, and then dry it with a dry cloth. Do not use benzene, thinner, or other solvents.

Lens front surface:

Wipe off dirt and dust with a soft, clean cloth. Do not use excessive force as the lens is fragile.

Air filter unit:

Perform maintenance when the air filter is clogged with dust, indicated by a message on the screen and the indicator lighting in red.

1. Removing the air filter unit:

• Turn off the projector power.

• Loosen the air filter cover fixing screw with a Phillips screwdriver and remove the air filter cover.

• Slightly push the grip of the air filter unit inward and pull it out.

2. Performing maintenance:

• Wash the air filter unit by soaking it in cold or warm water and then rinsing it lightly. Rinse it two to three times with fresh water.

• Dry the air filter unit naturally in a well-ventilated place away from direct sunlight. Do not use a dryer.

3. Attaching the air filter unit:

• Attach the clean, dry air filter unit back into the projector until it clicks.

• Attach the air filter cover until it clicks and securely tighten the fixing screw.

After cleaning or replacing the filter, you must reset the filter counter in the projector’s menu.

After cleaning or replacing the air filter unit on your PANASONIC PT-MZ570, you must reset the filter counter. Follow these steps:

1. Turn on the power of the projector.

2. Press the

If the power does not turn on for your PANASONIC PT-MZ570, please check the following points:

• Is the power plug firmly inserted into the outlet?

• Is the

If no image appears from your PANASONIC PT-MZ570, check the following:

• Are connections to external devices correctly performed?

• Is the input selection setting correct?

• Is the [BRIGHTNESS] adjustment setting at a minimum?

• Is the external device that is connected to the projector working properly?

• Is the shutter function in use? Press the button to check.

• If the power indicator is blinking in red, consult your dealer.

If the projected image from your PANASONIC PT-MZ570 is fuzzy, please check these points:

• Is the lens focus set correctly?

• Is the projection distance appropriate for the screen size?

• Is the lens dirty? If so, clean it carefully.

• Is the projector installed perpendicular to the screen?

If there is no audio output from your PANASONIC PT-MZ570, please verify the following:

• Is the external device connected correctly to the audio input terminal?

• Is the volume set to minimum? Try increasing the volume.

• Is the mute function used? Press the button to disable it.

• Is [AUDIO IN SELECT] in [AUDIO SETTING] correctly set?

• Is there a cable connected to the terminal? Audio is not output from the built-in speaker when a cable is connected to this terminal.

If the remote control for your PANASONIC PT-MZ570 is not responding, check these possible causes:

• Are the batteries depleted?

• Is the polarity (+/–) of the batteries set correctly?

• Are there any obstructions between the remote control and the remote control signal receiver on the projector?

• Is the remote control being used beyond its effective operation range (approx. 30 m or 98’5″)?

• Are other forms of light, such as fluorescent lighting, interfering with the projection?

• Is the [REMOTE CONTROL] setting in [CONTROL DEVICE SETUP] set to [DISABLE]?

• Is the ID number setting operation correct?

The [SELF TEST] display on your PANASONIC PT-MZ570 shows alphanumeric symbols for errors or warnings. Here are some common codes and their meanings:

Action number guide:

• 1: The operating environment temperature is too high or too low. Use the projector in an appropriate operating environment.

• 3: Battery replacement is required. Consult your dealer.

• 4: If the display does not clear after switching the main power off and on, consult your dealer.

• 5: The light source has failed to turn on. If it does not light up after turning the power off and on, consult your dealer.

• 6: Perform maintenance or replacement of the filter.