PANASONIC KX-TGU433 (02) PDF Document

First, connect the AC adaptor to the unit by pressing the plug firmly. Then, fasten the cord by hooking it. Connect the AC adaptor to the power outlet. Finally, connect the telephone line cord to the unit, then to the single line telephone jack until you hear a click.

Open the battery cover on the handset. Insert the rechargeable Ni-MH batteries, size AAA (R03), ensuring the polarities are correct. Close the battery cover securely.

The batteries for the PANASONIC KX-TGU433 should be charged for about 7 hours.

Lift the handset and dial the phone number. Press the Talk button to make the call. To use the speakerphone, press the Speakerphone button instead.

When the unit rings, lift the handset and press the Talk button or the Speakerphone button.

Press the Phonebook button then Menu. Select Add new entry. Enter the party’s name and press OK. Enter the party’s phone number and press OK. Select the desired group and confirm by pressing Select twice.

If you subscribe to the service, you will hear a tone if another call comes in. Press the Flash button to answer the second call. To switch between calls, press the Flash button again.

While talking, press the Volume Up or Volume Down button on the side of the handset repeatedly to set the desired volume.

When you receive an unwanted call, press the Call Block button. Confirm the number and press Yes to store it in the block list and disconnect the call.

Press Menu then enter #101. Enter the current month, date, and year using two digits for each, then press OK. Enter the hour and minute, select AM or PM, then press Save.

On the base unit, simply press the Answer On/Off button. Alternatively, on the handset, press Menu then enter #327 to turn it on or #328 to turn it off, then press Off.

Press Menu then enter #302. Select Yes and press Select. Speak your greeting clearly into the microphone after the beep. Press Stop to end the recording.

Press Menu then enter #323 on the handset, or press the Play button on the base unit if the message indicator is flashing.

On the base unit, press the Erase button twice while the unit is idle. Alternatively, on the handset, press Menu then enter #325, select Yes, and press Select.

First, confirm the base unit is connected to power. Move the handset closer to the base unit. You may need to unplug the base unit’s AC adaptor and plug it back in to reset the connection. If these steps fail, re-register the handset to the base unit.

On the handset, press Menu then enter #130. On the base unit, press and hold the Locator button for about 5 seconds. Finally, press OK on the handset and wait until a long beep sounds.

Press Menu then enter #120. Use the navigator keys to select either Tone or Pulse as required by your service provider, then press Save.

Press and hold the zero key until the unit beeps. This will turn the ringer off. Press and hold the zero key again to turn it back on.

While on a call, press the Boost key. The unit will display the Boost icon. Use this with caution as the volume will increase substantially.

Press the Flashlight key on the side of the handset to turn it on or off. The flashlight will turn off automatically after 5 minutes.

Press the CID button. You can then scroll through the list using the navigator keys.

Press the Call Block button, select Blocked calls count, press Select. When the count is displayed, press Clear. Select Yes and press Select to confirm.

Press Menu and enter #110. Use the navigator keys to select the desired language, then press Save.

Press Menu, select Intercom, and press Select. Select the desired handset and press Select to start the call.

On the monitored handset, press Menu then enter #268. Select On and press Select. Choose the monitoring handset and press Save.

Press Menu then enter #238. Select On to activate it, press Save. You can then set the start and end time during which the phone will not ring.

Press and hold the desired speed dial key (1 through 9). Press Add, then choose either Manual to type a number or Phonebook to select an existing entry. Follow the on-screen instructions to save.

Press Menu then enter #295. Select the desired entry slot and press Add. Follow the prompts to enter the name, number, and select a ringer tone.

During an outside call, press Menu, select Intercom and press Select. Select the handset you want to join, wait for the answer, then press Menu, select Conference and press Select.

The Flash button allows you to use special features of your host PBX, such as transferring extension calls or accessing optional telephone services.

While talking, press Menu. Select Noise reduction on using the navigator keys and press Select. This reduces surrounding noise from the other party’s phone.

Yes. While on an outside call, press Menu, select 2 way recording and press Select. The recording will start, and the unit will announce this to both parties.

While on a call, press the Phonebook button. Select the entry you wish to use and press Call to dial the stored number.

Press Menu then enter #211. Select the number of rings or Toll saver, then press Save.

The handset will display a battery icon. When the icon flashes or shows empty, the batteries need to be charged.

If the handset beeps or the battery icon flashes incorrectly, clean the battery ends and charge contacts with a dry cloth, then charge the batteries fully.

Press Menu then enter #720. Select the desired alarm, then select an option like Once, Daily, or Weekly. Follow the prompts to set the time and alarm tone.

This feature identifies calls that disconnect after one or two rings as potential scam calls, helping you avoid calling back expensive international numbers.

Press Menu then enter #798. Select the desired setting like 1 ring, 1 or 2 rings, or Off, and press Save.

During an outside call, lift the handset and press the Tele.blk key. This prompts the caller to state their name before you decide to answer or block the call.

Press Menu then enter #306. Enter your new 3 digit access code and press Save.

The battery level icon on the display indicates the level: High, Medium, Low, or Empty. When the icon flashes, it needs charging.

During a call, press Menu, select Equalizer and press Select. Choose your preferred setting for a more natural-sounding voice.

Press the Volume Up or Volume Down buttons on the base unit repeatedly until the desired volume level is set.

In the caller list, select the entry, press Menu, select Edit, then press Edit repeatedly until the number is in the desired format, then call the number.

This feature screens incoming calls by playing a greeting message that prompts the caller to enter an access code, ensuring the call is not automated before it rings on your phone.

Press Menu then enter #787. Select the desired setting, such as Block or Unblock, and press Save.

Yes. In the caller list, select the desired entry, press Menu, then select Save allow name and press Select.

Press Menu then enter #345. Select Off and press Save.

Press Menu then enter #330. The speakerphone will turn on and allow you to follow the instructions for your voicemail service.

Clean the charge contacts on the handset, base unit, and charger with a soft, dry cloth at least once a month.

The total recording capacity for the PANASONIC KX-TGU433 is approximately 17 minutes, with a maximum of 64 messages.

Press the Call Block button. Select Single number or Range of numbers and press Select. Press Menu, select Unblock all, press Select, then confirm by selecting Yes.

Press the Phonebook button, press Menu, select Group, and press Select. Choose the group, select Group name, edit the name, and press Save.

Press Menu, enter #104. Enter the desired name (up to 10 characters) and press Save.

Press Menu, enter #131. Select the handset you wish to cancel, press Select, then select Yes to confirm.

Press Menu, enter #162 for the handset, or #*162 for the base unit, select On and press Save.

Press Menu, enter #305. Select the desired recording time limit from the available settings and press Save.

This feature automatically reduces handset power consumption by suppressing transmission power when the handset is close to the base unit.