PANASONIC KX-TGU430 (02) PDF Document

Connect the AC adaptor to the unit by pressing the plug firmly. Fasten the cord by hooking it. Connect the AC adaptor to the power outlet. Connect the telephone line cord to the unit and to the single line telephone jack until you hear a click.

Open the battery cover. Insert the two rechargeable Ni-MH AAA batteries with the correct polarities as indicated by the plus and minus signs inside the compartment, then close the cover.

Charge the batteries for about 7 hours. The handset will display Charging while charging and Fully charged when finished.

Use only rechargeable Ni-MH batteries AAA size. Do not use alkaline, manganese, or Ni-Cd batteries.

Lift the handset and dial the phone number. Press the Talk button to make the call. To use the speakerphone, press the Speakerphone button.

Lift the handset and press the Talk button or the Speakerphone button when the unit rings.

Press the Volume up or Volume down button on the side of the handset repeatedly while talking.

Press the Boost button while on a call. The unit will display Boost. Use this feature with care to prevent hearing damage.

Press the Menu button during an outside call, select Hold, and then press the Select button.

Press the Mute button during a call. To return to the conversation, press the Mute button again.

Press the Menu button during an outside call and select 2 way recording. The unit will announce the start of recording.

Press the Call Block button when an incoming call is being received, during a call, or while a call is being recorded. Confirm the number and press Yes to save it to the block list.

Press the Menu button, then dial #101. Enter the current month, date, and year using two digits each, then press OK. Enter the current hour and minute using two digits each, select AM or PM, and press Save.

Press the Menu button, then dial #110. Select the desired setting and press Save.

Press and hold the zero button until the unit beeps to turn the ringer off. Repeat to turn it back on.

It allows you to hear the other person more clearly by reducing background noise from their line. Press the Menu button while talking and select Noise reduction on or Noise reduction off.

Press the Menu button, select Intercom, then select the desired unit. Press Select.

Press the Phonebook button, then the Menu button. Select Add new entry. Enter the name, press OK. Enter the number, press OK. Select the desired group and press Select.

Press and hold a dial key from 1 to 9, then select Add. Select Manual to enter information or Phonebook to select an existing contact.

On the base unit, press the Answer On/Off button. On the handset, press the Menu button, then dial #327 to turn it on or #328 to turn it off.

On the base unit, press the Play button. On the handset, press the Menu button, then dial #323.

Press the Erase button twice on the base unit while not in use, or on the handset press the Menu button, then dial #325.

It screens incoming calls. If the caller is not in your phonebook, favorites, or allowed list, the unit plays a greeting asking them to enter an access code before the unit rings.

On the handset placed in the room to be monitored, press the Menu button, then dial #268. Select On, then select the number of the handset to monitor with.

Press the Menu button, then dial #161 on the handset to select a ringer tone.

Place the handset on the base unit or charger to turn it on, and ensure the batteries are fully charged.

On the handset, press the Menu button, then dial #130. On the base unit, press and hold the Locator button for about 5 seconds. Finally, press OK on the handset.

Press the Menu button, dial #131, select the handset you want to cancel, then select Yes to confirm.

Press the Flashlight button to turn it on or off. The light turns off automatically after about 5 minutes.

Press the Menu button, dial #176, select the desired alert interval, and press Save.

This feature notifies you when returning a call that is judged as a scam call. You can adjust this by pressing the Menu button, dialing #798, and selecting the desired number of rings or turning it off.

Press the Caller ID button. Use the up and down arrows to scroll through the list.

Press the Caller ID button, select the entry, press the Erase button, then select Yes.

Press the Menu button, dial #331, enter the access number, and press Save.

The unit’s answering system answers at the end of the 2nd ring if there are new messages, or at the end of the 5th ring if there are no new messages, allowing you to hang up before being charged for the call when calling from outside.

Press the Menu button, dial #310, select On, and press Save.

The handset will display Messages full, the message counter on the base unit will flash, and the unit will play a greeting asking callers to call again later.

Press the Menu button, dial #120, select Tone or Pulse, and press Save.

You can store up to 3 favorites names, phone numbers, and ringer tones. The Favorites key indicator will flash if there is a missed call from a favorite contact.

Press the Menu button, dial #273, select On, and press Save.

Press the Menu button, dial #104, enter the desired name, and press Save.

It allows you to screen calls to stop telemarketers by asking them to say their name, after which you can decide whether to answer or block the call.

Yes, by pressing the Menu button, selecting Intercom, and choosing Voice paging. Your voice will be heard through the speakers of all registered handsets.

The battery charge is low. You should place the handset on the base unit or charger to fully charge it.

Press the Call Block button, select Blocked calls count, and press Select. To exit, press the Off button.

Press the Menu button, dial #793, and confirm by pressing Yes.

On the monitored handset, press the Menu button, dial #269, select the desired sensitivity level, and press Save.

You should regularly change the 3-digit remote access code by pressing the Menu button, dialing #306, and entering a new code.

Yes, the charger for the handset can be mounted on a wall using screws.

The unit cannot be used to make or receive calls during a power failure.