FREE ENGLISH PANASONIC ES-LT20 (01) PDF USER GUIDE
FREE ENGLISH PANASONIC ES-LT20 (01) PDF USER MANUAL
FREE ENGLISH PANASONIC ES-LT20 (01) PDF OWNER GUIDE
FREE ENGLISH PANASONIC ES-LT20 (01) PDF OWNER MANUAL
FREE ENGLISH PANASONIC ES-LT20 (01) PDF REFERENCE GUIDE
FREE ENGLISH PANASONIC ES-LT20 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH PANASONIC ES-LT20 (01) PDF REFERENCE MANUAL
FREE ENGLISH PANASONIC ES-LT20 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH PANASONIC ES-LT20 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD PANASONIC ES-LT20 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What important safety precautions should I follow when using the shaver?
Please observe the following safety precautions:
• The outer foil is very thin and can be damaged if not used correctly. Always check that the foil is not damaged before use. Do not use the shaver if the foil or blades are damaged, as you could cut your skin.
• Stop using the shaver immediately if you notice any abnormality or failure.
• Do not shave with soap or clean the shaver with water when the adaptor is connected and operating.
• Do not share the shaver with family or others.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.
• This shaver has a built-in rechargeable battery. Do not throw it into fire, apply heat, or charge, use, or leave it in a high-temperature environment.
What precautions should I take when charging the shaver?
• Never use the adaptor in the bathroom or shower room.
• Only use the power cord and adaptor provided (RE7-51).
• Plug the adaptor into a household outlet where there is no moisture and handle it with dry hands.
• When disconnecting the adaptor from the outlet, always hold the adaptor itself. Tugging on the power cord may damage it.
• The power cord cannot be replaced. If the cord is damaged, the entire adaptor must be scrapped.
• Charge the shaver in an ambient temperature between 15-35 °C.
How should I clean the shaver safely?
• **Warning:** Always disconnect the power cord from the shaver before cleaning it in water to prevent electric shock.
• Ensure both inner blades are inserted during cleaning. Cleaning with only one blade inserted may damage the shaver.
• If cleaning with water, use tap water or soapy tap water. Do not use salt water or hot water.
• Do not soak the shaver in water for a long period.
• Clean the shaver housing (main body) using only a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol, or other chemicals.
• For model ES-LT50, do not wash the charging stand with water.
How should I store the shaver?
• After use, store the shaver in a place with low humidity.
• Avoid storing the shaver where it will be exposed to direct sunlight or other heat sources.
• Disconnect the power cord when storing. Do not bend the power cord or wrap it around the shaver.
• Store or dispose of the plastic travel pouch properly to prevent accidents like infant suffocation. Keep the plastic bag away from infants.
• Keep the provided oil away from children.
How do I use the lock ring?
The lock ring is used to lock or unlock the power switch [0/1].
1. Rotate the lock ring until it clicks.
• **Unlock (LOCK position pointing away from the power switch):** Use this position for shaving, washing the shaver, or lubricating the shaver.
• **Lock (LOCK position pointing towards the power switch):** Use this position when carrying the shaver to prevent it from accidentally turning on.
How do I charge the shaver directly?
1. Ensure the shaver is turned off.
2. Insert the appliance plug into the shaver’s appliance socket.
3. Plug the adaptor into a household outlet.
Charging is completed after approximately 1 hour.
How do I charge the shaver using the charging stand (ES-LT50 only)?
1. Insert the appliance plug into the charging stand.
2. Place the shaver onto the charging stand.
3. Plug the adaptor into a household outlet.
Charging is completed after approximately 1 hour.
How do the indicator lamps behave during charging?
While charging:
• **ES-LT50:** The charge status lamp (plug symbol) glows. The battery capacity lamps (20-100) will light up progressively as charging progresses.
• **ES-LT20:** The charge status lamp (plug symbol) glows.
After charging is completed:
• **ES-LT50:** All the battery capacity lamps (20-100) will light up and then turn off after 5 seconds.
• **ES-LT20:** The charge status lamp (plug symbol) turns off.
Note:**
• When charging for the first time, or if the shaver hasn’t been used for over 6 months, the charge status lamp may not glow immediately but will eventually glow if kept connected.
• If there is a problem with charging, the charge status lamp (plug symbol) will blink.
Can I shave using the power cord if the battery is low?
How do I use the shaver for shaving?
1. Rotate the lock ring to the unlock position.
2. Press the power switch [0/1] to turn the shaver on.
3. Hold the shaver as illustrated (fingers on the finger rest, not covering the power switch) and shave.
• Start by applying gentle pressure to your face.
• Stretch your skin with your free hand.
• Move the shaver back and forth in the direction of your beard growth.
• You can gently increase pressure as your skin gets used to the shaver, but excessive pressure won’t provide a closer shave.
• Avoid placing fingers on the power switch while shaving, as this might turn the shaver off or activate the sonic vibration cleaning mode.
What is the sonic vibration cleaning mode and how is it activated?
How do I use the pivot action selector?
How do I use the trimmer?
1. Slide the trimmer handle up to pop up the trimmer.
2. Hold the shaver so the trimmer blade is at a right angle to your skin.
3. Move the shaver downwards to trim sideburns or shape facial hair.
How do the indicator lamps behave during use?
While using (battery):
• **ES-LT50:** Shows the approximate remaining battery charge as 20-100 (%). The corresponding lamp segment will light up (e.g., 60 lights up for 60-79% charge).
• **ES-LT20:** The battery capacity lamp (battery symbol) glows.
• The lamps turn off approximately 5 seconds after operating the switch.
While using (corded):
• The charge status lamp (plug symbol) glows.
What happens when the battery capacity is low?
• **ES-LT50:** The “20%” battery capacity lamp blinks when operating the shaver.
• **ES-LT20:** The battery capacity lamp (battery symbol) blinks when operating the shaver.
• When the low battery indicator starts blinking, you can typically shave 2 to 3 more times (depending on usage).
• A full charge provides enough power for approximately 14 shaves of 3 minutes each.
How do I clean the shaver with water (Sonic Vibration Cleaning)?
1. Disconnect the power cord from the shaver.
2. Apply some hand soap and a little water to the outer foil.
3. Rotate the lock ring to unlock the power switch.
4. Press and hold the power switch for more than 2 seconds to activate the sonic vibration cleaning mode.
• ES-LT50: The battery capacity lamps blink in order (20 -> 40 -> 60 -> 80 -> 100).
• ES-LT20: The battery capacity lamp (battery symbol) and the charge status lamp (plug symbol) blink alternately.
• The mode runs for about 20 seconds then turns off automatically, or you can press the power switch to turn it off sooner.
5. Remove the outer foil section (press the foil frame release buttons ④). Press and hold the power switch again for more than 2 seconds to activate the sonic vibration cleaning mode, then rinse the outer foil section and the main body (especially the inner blades) under running water.
6. Wipe off any water drops with a dry cloth.
7. Allow the outer foil section and the shaver main body to dry completely, preferably with the outer foil section detached.
8. Attach the outer foil section back onto the shaver.
9. Lubricate the shaver.
How do I lubricate the shaver?
To maintain shaving comfort, lubricate the shaver using the provided oil after cleaning or before use.
1. Switch off the shaver.
2. Apply one drop of oil to each of the system outer foils (②).
3. Raise the trimmer and apply one drop of oil to it.
4. Switch the shaver on and let it run for approximately five seconds to distribute the oil.
5. Switch off the shaver and wipe off any excess oil from the outer foils with a soft cloth.
How do I clean the shaver parts with the brush?
• **Inner Blades:** Use the short end of the cleaning brush. Move the brush in direction (A) as shown in the diagram (horizontally across the blades). Do not move the short brush vertically (direction B in the diagram) as this can damage the inner blades and affect sharpness.
• **System Outer Foil, Shaver Body, Trimmer:** Use the long end of the cleaning brush.
• **Caution:** Do not use the short end of the brush to clean the outer foils.
How often should I replace the outer foil and inner blades?
| Part | Replacement Frequency |
|---|---|
| System outer foil | Once every year |
| Inner blades | Once every two years |
How do I replace the system outer foil?
1. Press the foil frame release buttons (④) on the sides of the main body and lift the outer foil section (B) upwards to remove it.
2. Press the system outer foil release buttons (③) on the sides of the foil frame (①) and pull the system outer foil (②) down to remove it from the frame.
3. Align the foil frame mark (triangle on the frame) with the new system outer foil mark (triangle on the foil) and press them together securely. The system outer foil cannot be attached reversed.
4. Ensure the foil frame mark (triangle) is facing the front of the shaver, then securely attach the outer foil section back onto the shaver main body until it clicks.
How do I replace the inner blades?
1. Press the foil frame release buttons (④) and lift the outer foil section (B) upwards to remove it.
2. Remove the inner blades (C), one at a time, by grasping them firmly at both ends and pulling straight off.
• **Caution:** Do not touch the sharp edges (metal parts) of the inner blades to avoid injury.
3. Insert the new inner blades, one at a time, pressing down firmly until they click into place.
What are the replacement part numbers?
Replacement parts are available at your dealer or Service Center.
| Replacement parts for ES-LT50/ES-LT20 | Part Number |
|---|---|
| System outer foil | WES9087 |
| Inner blades | WES9068 |
How do I remove the built-in battery for disposal?
Remove the built-in rechargeable battery *only* when disposing of the shaver. Do not attempt to dismantle or replace the battery for re-use, as this could cause fire or electric shock. Battery replacement should be done at an authorized service center.
Please dispose of the battery at an officially designated location, if available in your country.
1. Disconnect the power cord from the shaver.
2. Perform steps ① to ④ as shown in the diagram (likely involving removing screws and housing parts) to access the battery.
3. Lift the battery out and remove it.
What are the specifications of the shaver?
| Product name | AC/Rechargeable Shaver |
| Product model | ES-LT50/ES-LT20 |
| Rated input | 100-240V~ 50-60Hz 180mA |
| Rated output | 5.4V === 1.2A |
| Motor voltage | 3.6V — |
| Charging time | Approx. 1 hour |
| Place of origin | Main body: Japan Adaptor: China Charging stand (ES-LT50): China |
| Date of production | See engraving on the commodity. |
This product is intended for household use only.
CLICK HERE TO DOWNLOAD PANASONIC ES-LT20 (01) PDF MANUAL