PANASONIC AW-RP50 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD PANASONIC AW-RP50 (01) PDF MANUAL


PDF Content Summary: AW-RP50 Simple Manual Getting started • Camera control has 2 kinds of protocol. – Serial(RS422) – IP(Ethernet) • Both cables are CAT5. But CAT5 has 2 kinds of interconnections. – RS422(Serial): Cross Cable because direct connection. – IP(Ethernet): Straight Cable because it is connected to HUB. • Don’t forget menu setting of RP50. – [SYSTEM] – [CAMERA CTL] – [CAM1] to [CAM100] • Select Serial or Network Note for Serial Connection

HE50: CAT5 cable must be cross type. And You need Multi-Interface Cable AW-CA20T6G and RJ-45 relay adapter HE120:CAT5 cable only. There is no need to use special cable.

Auto Setup of IP Address • IP Address Auto Setting – If you cannot connect to a camera, try to do auto setup. – [MENU] --[SYSTEM] -- [AUTO SET IP] -- [AUTO SET UP] – [RENEW IP ADR] and press the F2 dial. – Turn the F2 to select YES and press the F2 dial Manual Setup of IP Address • IP Address Manual Setting – [MENU] -- [SYSTEM] -- [NETWORK] – Press F1 dial and turn F1. – Select [IP ADDRESS] and Press the F2 dial. – Turn F2 dial. – Select IP address and press F2 Dial.

Factory Setting • Initialize – [MENU] -- [SYSTEM] -- [INITIALIZE] – Turn F2 dial and select [ALL] or [SETUP] and press F2. Outlook

Power ON/OFF of cameras

Power ON/OFF one camera 1.Select the camera. Hold down the number button. 2.Turn the F2 dial to select [ON] and Press the F2 dial. Note: Hold down the number button during setting. Power ON/OFF all cameras Menu – 8 (CAMERA) Power All Off Select POWER by F1 Press F1 Power All OnSelect ALL ON by F2 Press F2

Basic Operation 1. How to adjust a camera. 1. Press MENU button and select a function. 2. How to control Pan/Tilt, Iris and Zoom. 1. Press PC ACTIVE button, Adjust PTZ/SPEED dial, and use PAN/TILT lever, ZOOM lever, FOCUS dial and IRIS dial. 3. How to preset a camera position. 1. Select a camera (CAMERA STATUS / SELECTION), move to the specific position, press STORE button, press PAGE button, and hold down Number button. Advanced Operation 1. Camera Detailed Setting by OSD 1. Hold down the [CAMERA OSD] 2. Use F1/F2 to select an item. 3. Top Menu 1. Camera Scene 2. System 3. Maintenance MENU (Camera Adjustment) 1. Press [Menu] – If [PAGE] button lights on, you cannot switch [ON]. 2. Press number button of PRESET MEMORY/MENU area. – 1: GAIN/PED, 2: R/B GAIN, 3: R/B PED, 4: AWB/ABB, 5: SHUTTE, 6: DETAIL, 7: SCENE/MODE, 8: CAMERA, 9: SETUP, 10: SYSTEM 3. Turn F1/F2 to change mode or adjust. 4. Some settings (AWB,ABB,MODE and so on) require to execute. At that time press F1 or F2 to execute. Control Pan/Tilt • Hold down the [PT ACTIVE] • Select a Camera (SELECTION) • Adjust IRIS • Auto button lights on: Auto iris • Auto button lights off: Manual iris • ZOOM lever • Adjust FOCUS • Auto button lights on: Auto focusing. • Auto button lights off: Manual focusing – OTAF: One-touch autofocus – Press focusing dial and autofocusing works. • Adjust PTZ/SPEED dial • Clockwise: Speed increases. Counter-clockwise: Speed decreases. • Make a camera move by PAN/TILT lever PRESET (Camera Position Store) • How to store the camera position. 1. Select a camera. (1~5) 2. Adjust the camera position. 3. Press the [STORE] button. 4. Press the[PAGE] button and then press the number button. 1. This is page number. 5. Hold down the number button. 1. This is number of the page. 2. If you press 2 and 5, preset number becomes 25. PRESET (Camera Position Recall) • Executing the preset data. 1. Select a camera. (1~5) 2. Press the [PAGE] button and then press number button. 1. This is page number. 3. Press the number button. 1. This is number of the page. 4. The camera moves to the preset number position. 1. If you press 2 and 5, the camera moves to the preset number 25. Delete PRESET (Camera Position) • Deleting the preset data. 1. Select a camera. (1~5) 2. Press the [DELETE] 3. Press the [PAGE] button and then press the number button. 1. This is page number. 4. Hold down the number button. 1. This is number of the page. 5. If you press 2 and 5, the data of the preset number 25 is deleted.

Setting the USER buttons

The Movement Range of the Remote Camera (Limiter Function) Note: Move the camera to the position where you want to limit at first. Limit position becomes the position where you turn on. Appendix Camera OSD CAMERA OSD (HE120) 1. Hold down the [CAMERA OSD] 2. Use F1/F2 to select an item. 3. Top Menu Camera Scene: Scene1~4 Scene Brightness Picture Matrix System Genlock Output Other Maintenance Firmware Version IP Network Initialize 4. Press Return to return to upper menu. Camera Scene (HE120)

• Scene : Scene1 ~ 4 – Brightness • Picture Level • Iris Mode • Shutter Mode – Step/Synchro • Gain – AGC Max Gain • Frame Mix • ND Filter • Return – Picture • Chroma Level: -3~+3 • White Balance Mode : AWB A/AWB B/3200K/5600K – R Gain: -150~+150 – B Gain: -150~+150 • Pedestal – R Pedestal [#] – B Pedestal [#] • Return – Matrix • Matrix Type : Normal/EBU/NTSC/User – [Linear Matrix] – [Color Correction ½] – [Color Correction 2/2] • Scene – Matrix • Matrix Type : Normal/EBU/NTSC/User – [Linear Matrix] » Saturation Phase » R-G » R-B » G-R » G-B » B-R » B-G – [Color Correction 1/2] » Saturation Phase » B_Mg » Mg_R » R » R_Yl » Yl – [Color Correction 2/2] » Saturation Phase » Yl_G » G » G_Cy » Cy » Cy_B » B

System (HE120) • Genlock – Horizontal Phase:-206~+49 – Horizontal Phase Step:1~10 • Output – Format: 1080/59.94i/720/59.94p/1080/29.97PsF/ – Down CONV. Mode: Squeeze/SideCut/LetterBox – HDMI Color: RGB-NOR/RGB-ENH/YCbCr422/YCbCr444 – Component: Y/Pb/Pr, RGB – Frequency: 59.94Hz/50Hz – Color Bars Setup: Off/On • Other (Next Page) – Other 1/3 – Other 2/3 – Other 3/3 Other (HE120) • Other 1/3 – Install Position: Desktop/Hanging – Smart Picture Flip: Off/Auto • Flip Detect Angle: 60~120 – Preset Speed: 1~30 – Preset Scope: Mode A/Mode B/Mode C – Digital Zoom: Enable/Disable – Speed With Zoom POS. – Return • Other 2/3 – Focus Mode:Auto/Manual • Focus ADJ With PTZ.: On/Off – Digital Zoom: Enable/Disable • Max Digital Zoom:x2~x10 – Tally Enable :Enable/Disable – Wireless Control :Enable/Disable – Return • Other 3/3 – OSD Mix • SDI Out: On/Off • HDMI Out: On/Off • Component Out: On/Off • Video Out: On/Off – OSD Off With Tally: On/Off – OSD Status: On/Off – Return CAMERA OSD (HE50) 1. Hold down the [CAMERA OSD] 2. Use F1/F2 to select an item. 3. Top Menu Camera Scene: FullAuto/Manual1~3 Scene Contrast Picture Color Matrix System Genlock Output Other Maintenance Firmware Version IP Network Initialize 4. Press Return to return to upper menu. Camera Scene (HE50)

• Scene : FullAuto, Manual1~3 – Contrast • Contrast Mode – Contrast Level: -5~+5 – Shutter Mode » Step/Synchro » Frame Mix » AutoF.Mix Max Gain :0,6,12,18dB • Gain: Auto,0dB,3dB,6dB,9dB,12dB,15dB,18dB • AGC Max Gain: 6dB,12dB,18dB • Return – Picture • Chroma Level: -3~+3 • AWB Mode : AWB A/AWB B/ATW • Detail: Off/Low/High • Flesh Tone Mode: Off/Low/High • DNR: Off/Low/High • DRS: Off/Low/High – Gamma Type: Normal/Cinema//Off – Gamma Level: Low/Mid/High @Normal • Back Light Comp.: Off/Onj • Return – Matrix • Matrix Select : Normal/EBU/NTSC/USER • Scene – Matrix (You can change at USER.) • Matrix Select : Normal/EBU/NTSC/User – [1/3] » Saturation Phase » Axis01 » Axis02 » Axis03 » Axis04 » Axis05 » Axis06 – [2/3] » Saturation Phase » Axis07 » Axis08 » Axis09 » Axis10 » Axis11 » Axis12 – [3/3] » Saturation Phase » Axis13 » Axis14 » Axis15 » Axis16

System (HE50) • Genlock – Horizontal Phase:-206~+49 – Subcarrier Phase • Coarse: 0.45,90,135,180225,270,315 • Fine: =127~+127 – H Phase, SC Fine Step:1~10 • Output – Format: 1080/59.94i/720/59.94p/1080/29.97PsF/ – Down CONV. Mode: Squeeze/SideCut/LetterBox – HDMI Color: • Other (Next Page) – Other 1/2 – Other 2/2 Other (HE50) • Other ½ – Install Position: Desktop/Hanging – Preset Speed: 1~30 – Preset Scope: Mode A/Mode B/Mode C – Digital Zoom: Enable/Disable – Speed With Zoom POS. – Focus Mode: Manual/Auto • Focus ADJ With PTZ.: Off/On – Return • Other 2/2 – Tally Enable: Enable/Disable – OSD Off With Tally: Off/On – OSD Status: Off/On – Wireless Control :Enable/Disable What is SCOPE?


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply