Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** OPERATING MANUAL & PARTS LIST GENERAL PURPOSE ANGLE VISES MODELS: 961 1 152 961 1253 961 1255 Read carefully and follow all safety rules and operating instructions before first use of this product. 9650001.00 – 07/14
****** Page 2 ****** Palmgren Operating Manual & Parts List DESCRIPTION Palmgren General Purpose Angle Vises are assembled in the U.S., and are constructed from fine grain cast iron with replaceable steel jaw plates. Lead screws on all models are precision cut V-thread. Palmgren General Purpose Angle Vises permit accurate positioning at any angle from horizontal to vertical. Model 9611255 comes with a 3600 swivel base with a 5/8″ keyway. Center of base is open for holding work through body of vise. Base and bed are parallel to 0.002″ on all vises. SAFETY RULES Understand and obey all safety instructions supplied with drill press, mill or other machines on which vise is used. Bolt or clamp vise to work surface in at least two mount- ing locations using mounting lugs on swivel base or angle base. Be sure workpiece is clamped securely between jaws before starting machining operation. Do not over tighten—vise can develop a large clamping force. Use only force which is needed. Do not pound or hammer on workpiece. This vise is designed to clamp the workpiece in a desired position for machining operations only. Model 9611152 9611253 9611255 Figure 1 – Dimensions 1-1/2″ 2-7/16″ 2-7/16″ B 2″ 3-3/16″ 3-1/8 11 c O c 1-1/2 2-1/2 2-1/2 D 1-1/2 1-1/2 5-3/4 7-1/2 7-1/2″ 10-3/41 11-1[2″ G 2-3/8″ 3-7/8″ 4-9/16″ Wei ht 4 lbs 10 lbs 14 lbs A B Refer to Figure 1. OPERATION Refer to Figure 2. • Mount vise to work surface in desired location. • Open jaws of vise and place workpiece between jaws in desired position. Secure workpiece between jaws by rotat- ing leadscrew with handle (Ref. No. 3). Be sure workpiece is held securely in vise before starting machining operation. Particles of metal or wood can damage machined surfaces, causing difficult or inaccurate operation. The vise is shipped with a protective coating. This coating should be removed before operation. Use penetrating oil to remove protective coating. Keep machined surfaces and all moving parts clean and free of dirt, chips and foreign materials. Keep machined surfaces and lead screws lubricated with medium weight machine oil. 2
****** Page 3 ****** Palmgren Operating Manual & Parts List 5 3 2 4 6 5 1 0 7 8 Figure 2 – Replacement Parts Illustration for General Purpose Angle Vises REPLACEMENT PARTS LIST FOR GENERAL PURPOSE ANGLE VISES Ref. No. 1 2 3 4 5 6 7 8 9 (N/A) – Description Body Follower Lead Screw Assembly Bottom Plate Kit Jaw Plate Kit Swivel Base Kit Angle Base Kit Single Side Plate Kit Palmgren Nameplate Model 9611152 N/A N/A 9610008.00 9610024.00 9610014.00 9610101.10 9610050.00 N/A Model 9611253 N/A N/A 9610010.00 9610025.00 9610015.00 9610201.10 9610051.00 N/A Model 9611255 N/A N/A 9610010.00 9610025.00 9610015.00 9610047.00 9610201.10 9610051.00 N/A Not available as a replacement part. 3
****** Page 4 ****** Palmgren Operating Manual & Parts List WARRANTY Palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended. The warranty does not cover expendable and/or wear parts (i.e. v-belts, coated screws, abrasives), damage to tools arising from alteration, abuse or use other than their intended purpose, packing and freight. The duration of this warranty is expressly limited to the terms noted below beginning from the date of delivery to the original user.The Palmgren products carry the following warranties on parts with a 1 year warranty on labor: USA Machine vises — Lifetime IQ Machine vises – Lifetime Bench vises – Lifetime Positioning tables – Lifetime Bench grinders, buffers and belt grinders — 3 years Tapping machines — 3 years Drilling machines — 3 years Finishing machines — 3 years Band saws €- 3 years Work stands 3 years Arbor presses — 3 years Milling machines – 3 years Lathes — 3 years Accessories — 1 year The obligation of Palmgren is limited solely to the repair or replacement, at our option, at its factory or authorized repair agent of any part that should prove deficient. Purchaser must lubricate and maintain the product under normal operating conditions at all times. Prior to operation become familiar with product and the included materials, i.e. warnings, cautions and manuals. Failure to follow these instructions will void the warranty. This warranty is the purchaser’s exclusive remedy against Palmgren for any deficiency in its products. Under no circumstances is Palmgren liable for any direct, indirect, incidental, special or consequential damages including lost profits in any way related to the use or inability to use our products. This warranty gives you specific legal rights which may vary from state to state. SERVICE & REPAIR 2. 3. 4. If a Palmgren product requires a repair or warranty service DO NOT return the product to the place of purchase. All warranty related work must be evaluated and approved by Palmgren/C.H. Hanson. Prior to returning any item the user must obtain factory approval and a valid RGA number. For instructions and RGA number call toll free (800) 827-3398.
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL