PAC MCI-GM51 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD PAC MCI-GM51 (01) PDF MANUAL


PDF Content Summary: MCI-GM51 Introduction & Features Multi Camera Input Interface for select General Motors Vehicles

The MCI-GM51 will allow the addition of a reverse camera, two blind spot cameras, and one front view or trailer camera in vehicles equipped with either the 4” or 8” screen. Important Notes 1. Compatible build codes: IO4, IO5, and IO6. Incompatible build codes: IO3, IOA, and IOB. Build codes can be found on a silver sticker either in the glove box or in the trunk near the spare tire well. 2. If you change the DIP switch settings, you must disconnect and reconnect power for the change to take effect. 3. If you are installing this interface strictly to add a reverse camera, please note that the blind spot inputs will need to be deactivated (depending on the vehicle) by either: a. 8” Screen: Entering the menu and manually disabling the inputs (see page 3 for details) OR b. 4” Screen: Setting DIP switch number 4 to the down position (see page 2 for details) What’s Included 4 1 2 3 5 1 Module MCI-GM51 2 Power Harness BSM3-PTH 3 Video Input harness BSM2-CEH 4 Foam Padding Miscellaneous 5 LVDS Connectors Not available Separately

© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global. PAC-audio.com Pacific Accessory Corporation Rev. 120817 Page 1 MCI-GM51 DIP switches Set DIP switches according to the descriptions below Multi Camera Input Interface for select General Motors Vehicles DIP switch Functions: 1. Screen Size • Up for 8” screen • Down for 4” screen 2. Reverse Camera Screen Size Reverse Camera Model Year Trailer Cam Only 1 2 3 4 *DIP switch 4 only applies to vehicles with the 4” screen 3. Model Year • Up for 2015-2016 • Down for 2017 (Except Impala) 4. Trailer Camera Only (One camera only on input #3) • Up when vehicle has factory equipped reverse camera • Down when you are installing an aftermarket reverse camera Installation Steps • Up for full menu, four camera input • Down to enable one camera mode. This will disable all other inputs and show only the camera on input 3 when activated.

1. Set the DIP switches for your application based on the functions listed above. These DIP switches must be set to the proper configuration before connecting the interface to power. 2. Remove the factory screen assembly and disconnect the factory 10-pin power harness (Fig. A) Fig. A Fig. B Illustrations are typical and may not match exact vehicle details

3. Connect the MCI-GM51’s male power harness to the back of the factory screen assembly. 4. Connect the factory harness into the female connector on the MCI-GM51 power harness. 5. Locate the HMI module a. Trucks and SUVs: The HMI is located in the upper portion of the glove box opening. If your vehicle does not have an HMI module then it is not compatible. b. Passenger cars: The HMI module is located above the passenger kick panel. If your vehicle does not have an HMI module then it is not compatible. 6. Disconnect the blue LVDS connector from the HMI module. (Fig. B) 7. Connect the MCI-GM51’s male LVDS harness to the HMI module. 8. Connect the factory LVDS harness into the female LVDS connector on the MCI-GM51. 9. Connect the power harness to the MCI-GM51 module. 10. Connect the video harness to the MCI-GM51 module. 11. Connect cameras and corresponding camera power wire outputs according to the chart on the right. If the vehicle is equipped with a factory reverse camera, then Input 3 can be used for a trailer cam or not at all. Secure and insulate any camera inputs and power wires not being used to prevent any contact with metal. 12. If necessary, use the provided foam padding to insulate the module from any rattles before securing inside the dash cavity. Input Function Camera 1 Left Camera Camera 2 Right Camera Camera 3 Trailer Camera *Camera 4 Other Camera *This camera input is automatically activated when vehicle is in reverse gear, if DIP switch 2 is on. © 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global. PAC-audio.com Pacific Accessory Corporation Rev. 120817 Page 2 MCI-GM51 Operation Accessing User Interface 8” version (Fig. C-E) Multi Camera Input Interface for select General Motors Vehicles

Press and hold the “BACK” button on the factory dash panel (Fig. C) for three seconds to enter the camera menu. Press OK to accept the terms and continue. Use the touch screen to select the desired view. Press the “BACK” button to return to the previous screen. Press the gear icon in the top right corner to enter the camera setup menu (Fig. D-E). From here you can enable / disable MCI-GM51 functions. 1. Enable Front Camera Speedup Trigger - When enabled, will trigger front camera when exiting reverse and turn off after 8 mph. 2. Enable Front Camera Slowdown Trigger - When enabled, it will activate front camera when speed is reduced below 10 mph and steering wheel is turned more than 15 degrees. (This prevents unwanted front camera activation in stop and go traffic).

3. Enable Turn Signal Cameras - When enabled, blind spot cameras will activate and display on the screen when the turn signals are activated. 4. Enable Dynamic Backup Curves - When enabled, the MCI-GM51 will overlay dynamic backup guide lines over the reverse image (aftermarket cameras only). Press and hold the small lock icon in the top right corner of the camera setup menu to access additional settings. 1. Third camera in 3-way split view can be switched between inputs 3 and 4. 2. Adjustments to the dynamic curve lines can also be made from this menu (aftermarket cameras only). Input Function Camera 1 Left Camera Camera 2 Right Camera Camera 3 Trailer Camera *Camera 4 Other Camera *This camera input is automatically activated when vehicle is in reverse gear, if DIP switch 2 is on.

Fig. C Fig. D Fig. E 4” version (Fig. F)

Press and hold the “HOME” button (Fig. F) for three seconds to enter the camera view. Press and hold the “HOME” button for one second to cycle through the views. The order of views is: 1. Other Camera (Input 3) 2. Left Camera (Input 1) 3. Right Camera (Input 2) 4. Trailer Camera (Input 4) Press the “BACK” button to return to the factory screen. The camera view is accessible after 7 seconds while in reverse. Press and hold the “HOME” button on the for three seconds to access camera view. Fig. F

Illustrations are typical and may not match exact vehicle details

© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global. PAC-audio.com Pacific Accessory Corporation Rev. 120817 Page 3


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply