OSIGHT S (01) PDF MANUAL

The package contains the following items:

Optic

Charging Cover

Tool

Screwdriver Box (containing IPX-13, B4, IPX-40, and M3 screws)

Peach

Cleaning Cloth

USB-C Charging Cable

Table 1: Optic SPECIFICATIONS

Note: The battery life of the optic is based on its amount of use and the amount of light sensed on. For more runtime details, please visit osight.com.

Note: Please fully charge the product every three months to maintain stable power if not used.

Table 2: Osight S Charging Cover

Connect the charging cover to a power source using the provided USB-C cable. The battery icon on the cover will flash for 5 seconds and then turn off, indicating that it is charging. When charging is complete, the battery icon will be constantly on for 5 seconds and then turn off.

Note: Fully charge the product before first use.

Place the charging cover over the optic to begin charging it. The optic battery icon on the cover will flash for 5 seconds and then turn off, indicating that the optic is charging. When charging is complete, the optic battery icon on the cover will be constantly on for 5 seconds and then turn off.

Press any button (“+” or “-“) to turn the optic on. If the motion sensor function is enabled, the optic will also turn on automatically upon detecting any movement.

Press the “+” and “-” buttons simultaneously for more than 0.5 seconds to turn the optic off.

The motion sensor function is enabled by default. When active, it automatically turns the optic on when movement is detected and turns it off after 10 minutes of inactivity.

To enable or disable this function:

1. Press and hold the “-” button for over 3 seconds.

2. The reticle will flash once to indicate the function is enabled.

3. The reticle will flash twice to indicate the function is disabled.

The optic has two operation modes:

Auto Sensing Mode: This is the default mode. It uses a light sensor to automatically adjust the reticle brightness based on ambient light conditions. The brightness can also be manually adjusted up or down in this mode.

Manual Mode: In this mode, you manually set the brightness. There are 12 brightness levels available. Levels 1 and 2 are for night vision settings, and levels 3 to 12 are for daylight settings, with level 12 being the brightest.

While the optic is on, press and hold the “+” button for over 3 seconds to switch between modes.

The reticle will flash once to indicate a switch to Manual Mode.

The reticle will flash twice to indicate a switch to Auto Sensing Mode.

The optic will remember the last brightness setting used in Manual Mode.

When in Manual Mode, press the “+” button to increase brightness and the “-” button to decrease brightness.

While the optic is on, press and hold the “-” button for over 3 seconds. The optic will cycle through the three reticle types in the following order every 3 seconds: Circle -> Dot -> Circle-Dot. Release the button when your desired reticle is displayed to select it. All three reticles are available in both Auto Sensing and Manual modes.

To save power, the energy-saving function is automatically activated when the charging cover is placed over the optic. This action turns the reticle off. The reticle cannot be automatically activated again until the cover is removed. This function is disabled when the cover is not used.

After turning the optic on, press any side button (“+” or “-“) to display its battery level. An indicator light on the side of the optic will show the battery level for 5 seconds.

Green: 50%-100%

Yellow: 25%-50%

Red: <25%

Press the side button on the charging cover to display its battery level for 5 seconds. This can be done whether the optic is on the cover or not. The indicator light shows the battery level of the cover itself.

Green: 50%-100%

Yellow: 25%-50%

Red: <25%

1. Press the pawl of the cover to open the cover of the optic.

2. Use the included tool to tighten the screw and mount the optic onto the rail.

Use the included tool to rotate the adjustment screws on the optic. One click adjusts the windage (left/right) or elevation (up/down) by 1 MOA (Minute of Angle).

Do not ingest the battery, as it is a Chemical Burn Hazard.

If the small battery is swallowed, it can cause severe internal burns in just 2 hours and may lead to death. Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Do not replace the battery with a wrong type of battery that can defeat a safeguard, as this may cause an explosion or fire.

Do not dispose of the battery in a fire, hot oven, or by crushing or cutting it, as this may result in an explosion.

Avoid leaving the battery in an extremely high-temperature environment, as it may cause an explosion or the leakage of flammable liquid or gas.

A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

The WEEE (Waste Electrical and Electronic Equipment) symbol indicates that this product should not be disposed of with other household waste. To protect human health and the environment, you must dispose of your waste equipment by handing it over to a designated collection point for the recycling of WEEE, separated by the government or local authorities. Proper disposal and recycling will help prevent potential negative consequences to the environment and human health.