ORIGIN PRO PP50B (01) PDF MANUAL

ORIGIN PRO PP50B (01) PDF SUMMARY:

What does this instruction booklet cover?

This instruction booklet covers the necessary information for a smooth installation, including: the tools, step-by-step instructions for installation, troubleshooting tips for any errors that may occur, and all warranty information.

---

What is included with the speaker?

• Speaker (Available in Black or White)
• Cable Ties (3)
• Installation Manual
• Gripple® Suspension Kit Containing:
  • Gripple® Rope Grip (2)
  • Gripple Release Key
  • Hanging Cable (stainless steel)
  • Safety Cable (stainless steel)
• Grille Removal Key
• Guitar Pick (to turn Voltage selector tab)
• 4Pin PVC Connector Cover

---

How do 70V/100V systems work?

70/100-Volt systems are advantageous when the design calls for multiple speakers from the same amplifier and/or long-distance wire runs. These Professional Collection 70V/100V Pendant Speakers feature multiple taps off the transformer, adjusted by a rotary switch on the front face of the speaker. The higher the wattage selected, the more output will be generated by the speaker.

---

What is common in the U.S. versus internationally regarding voltage?

70V is common in the U.S. while 100V is the common voltage internationally, especially in Europe.

---

How do you calculate how many speakers can be driven on a single amplifier channel?

A simple calculation is used to determine how many speakers can be driven on a single amplifier channel. First, for safety purposes, it is recommended to make the calculations based on 80% of the amplifiers rated power.

For example, a 500-watt amplifier would safely deliver 400 watts of usable power (500 x 0.8 = 400). Now it is simply a matter of dividing 400 by the tap setting of the speakers.

For example, if the speakers are set at a 15W tap, the amplifier would be capable of driving 26 speakers per channel. At a 30W tap that would be 13 speakers. At a 60W tap that would be 6 speakers and so on.

---

What are the benefits of a 70V/100V system?

If coverage is needed over a wide area and it requires numerous speakers, a 70V/100V system presents a tremendous advantage. However, it should be noted that the higher the wattage tap, the higher the fidelity and the greater SPL that can be delivered from each speaker. It is best to determine the total number of speakers needed and set the taps as high as possible WITHIN the amplifier’s power output rating.

---

How do you adjust the tap setting?

The rotary switch used to adjust the tap setting is located on the front face of the speaker. For this reason, it is best to leave the grilles off until all of the tap settings have been properly adjusted.

---

What should you be cautious of when using the rotary switch?

There is an 8Ω setting for both voltages that bypasses the transformer entirely. Use caution to avoid this setting when connected to a 70V/100V amplifier as this can destroy the loudspeaker.

---

How do you determine the wattage draw on the amplifier when daisy-chaining multiple speakers?

When daisy-chaining multiple speakers: add the combined wattages of all tap settings, to determine the wattage draw on the amplifier. The combined total wattage should NEVER exceed the wattage rating of the amplifier.

---

What should you do if you are uncomfortable designing or installing a 70/100V system, or if you have any questions?

Contact Origin PRO Technical Support.

---

What factors determine speaker placement?

Speaker placement is determined by several factors like desired SPL, coverage requirements, variance in SPL by location, etc. When the objective is to fill a large area with very little variance (+/- 2dB), then a larger number of speakers are required.

---

How should speakers be placed for the best result?

Typically, once the number of speakers has been determined, placing them equidistant from the walls and from each other will deliver the best result. However, due to other factors this may not be possible. Also realize that the higher the ceiling the greater the conical dispersion and therefore the larger coverage area per speaker.

---

How does the distance from the listener and the proximity to a wall affect the speaker’s output?

The further the speaker is from the listener, the lower the SPL. As the speaker is placed closer to the wall, bass frequencies will be enhanced.

---

How does wire gauge affect speaker performance, and what gauges are suitable for different systems and lengths?

The gauge of wire used can have an impact on the performance of your speakers. Generally, speaker wire is determined by the length of the run and wattage utilized. The longer your run is, the smaller the wire gauge must be.

On commercial 70 Volt systems, 18 gauge, 2 conductor, stranded and jacketed without shield wire is commonly used.

In residential systems, for relatively short runs (less than 50 feet) to 8 ohm speakers, 16 gauge wire will be usually suitable.

• Wire Length Wire Gauge System:
  • 0 -200’ (0 – 60m) 18 70V / 100V
  • 200-500’ (60 -150m) 16 70V / 100V
  • Over 500’ (150m) 14 70V / 100V
  • 0 – 50’ (0 – 15m) 16 8 Ohm
  • 50 – 100’ (15 – 45m) 14 8 Ohm
  • Over 100’ (30m) 12 8 Ohm

---

How can speaker wire be routed?

• Under the Carpet: One option is to lift up the carpet and route “tape wire” under the carpet.
• Behind the Baseboard: The wire can be routed behind the baseboard by cutting a groove out of the back of the baseboard, or by buying special baseboard designed for concealing wires.
• Attic or Basement: When available, you can route the wire through an attic or crawlspace.
• Through Walls: When running wires through a wall, be sure to avoid all obstacles such as AC wiring, pipes, and ducts.

---

What is recommended if speakers are being installed in a new home during construction?

If these speakers are being installed in a new home during construction, it is recommended you purchase a bracket. Instructions on how to install the speakers are provided with the bracket, or can be found on the website. Visit http://www.originpro.com for more information.

---

What are the installation steps?

1. Insert hanging cable into the Gripple Rope Grip. Pass cable over ceiling anchor point (as shown) or through other secure anchor point of the building structure. Installer is responsible for secured anchoring.
2. Pass the returning cable through other hole in the Gripple.
3. Latch the suspension hook onto the center hole in the top bracket of the speaker. Adjust to proper height by pulling cable through either end of Gripple.
4. Latch secondary safety cable hook onto one of the side holes in the top bracket of the speaker, and loop the cable around a different ceiling support point of the building structure, per Steps 1 & 2.
5. After height adjustment is final, trim any unneeded extra cable tail wires with trimmer.
6. Make sure the weight of the load is supported.
7. Insert Release key into small hole at bottom of Gripple. Push in 1/4” to release the cable.
8. Adjust height.
9. Remove key and re-secure the load.
10. Install the 4Pin PVC Connector Cover over the wire cables.
11. Connect the wires from your amplifier to the 4Pin Terminal Connector. Strip approximately 3/16” (5mm) of the insulation off each wire. Insert the wire into the correct square opening on the connector. Use a small flat head screwdriver to tighten the corresponding screw to secure the wire.
12. Plug the male connector into the terminal connector at the rear speaker. Then, slide down the 4Pin PVC Connector Cover over the 4Pin Terminal Connector.
13. Determine the proper wattage setting for each speaker in the installation and set each speaker’s transformer tap selector on the front of the speaker accordingly. Use the included guitar pick to easily fit into the notch and turn the tap selector.
14. Fit the grille onto the speaker.

---

What are the wiring connection methods when using multiple speakers?

When using multiple speakers you can connect the speakers either in Parallel or in the Loop Through connection method.

---

What should you check if there is no sound?

• The volume may be turned down or muted. Check the volume settings on both the amplifier and the television/computer/CD player/etc.
• Make sure the proper source is selected on the amplifier or receiver.
• Check the cord connecting the amplifier with the source. The cord may be damaged or plugged into the wrong input or output.
• Check the wires connecting the amplifier with the speakers. Make sure they’re connected properly and not damaged in any way.

---

What should you check if the sound quality is poor?

• Check the audio cables. If you hear something like static, or the sound is cutting in and out, check the audio cables. If the problem increases when a cable is being moved, then the cable is most likely faulty or not connected properly.
• Check the volume on all devices. Today’s audio systems may have several places to adjust the volume, for example your MP3 player may have a volume control, and your amplifier may also have one. Check to be certain that the volume isn’t turned up past 80% on any device.
• Try changing sources. Check to be certain that the selection you’ve chosen is a good quality recording.

---

What does the Origin PRO warranty cover?

Origin PRO warrants to the original retail purchaser only that this Origin PRO product will be free from defects in materials and workmanship, provided the speaker was purchased from an Origin PRO authorized dealer. If the product is determined to be defective, it will be repaired or replaced at Origin PRO’s discretion. If the product must be replaced yet it is no longer manufactured, it will be replaced with a model of equal to or greater value that is the most similar to the original. If this is the case, installing the replacement model may require mounting modifications; Origin PRO will not be responsible for any such related costs.

---

What may invalidate the warranty?

This warranty may not be valid if the product was purchased through an unauthorized dealer. This warranty only applies to the individual that made the original purchase, and it cannot be applied to other purchases. The purchaser must be prepared to provide proof of purchase (receipt). This warranty will not be valid if the identifying number or serial number has been removed, defaced, or altered.

---

What is not covered by the warranty?

• Accidental damage
• Damage caused by abuse or misuse
• Damage caused by attempted repairs/modifications by anyone other than Origin PRO or an authorized dealer
• Damage caused by improper installation
• Normal wear, maintenance, and environmental issues
• Damage caused by voltage inputs in excess of the rated maximum of the unit
• Damage inflicted during the return shipment

---

How can you get technical assistance?

If you have any questions or concerns about installing or using this product, you can reach us through one of the following methods:

Phone: (844) 674-4461

Hours of operation: 8:00am – 5:00pm (Pacific Time), Mon – Fri

---

What should you have ready if you are having technical trouble and calling for technical assistance?

If you are having technical trouble, please have ready your model number and be prepared to briefly explain what steps you took to resolve the problem, to be best helped over the phone.

---

What is required before returning a product?

Before making any return attempts, it is required that you first contact Origin PRO.

---

What are the steps for the return process?

1. It’s required that you contact Origin PRO prior to any return attempts. This way we can determine if the issue can be resolved without returning the product, or if needed we can provide instructions and support for the return process.
2. Return product to Origin PRO or your dealer, either in person or by mail. It’s preferable if the product is returned in the original packaging. If this is not possible, the customer is responsible for insuring the shipment for the full value of the product.