ONKYO TX-NR777 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD ONKYO TX-NR777 (01) PDF MANUAL


PDF Content Summary: > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Basic Manual Before Start ............................................................................2 What's in the box......................................................................2 Part Names .............................................................................3 Part Names ..............................................................................3 Install ......................................................................................7 Installation procedure...............................................................7 Step1: Speaker Layout .............................................................8 Step2: Connect the Speakers.................................................14 Step3: Connect the TV & AV Components.............................16 Initial Setup ..........................................................................23 Initial Setup with Auto Start-up Wizard...................................23 Playback ...............................................................................25 AV Component Playback........................................................25 BLUETOOTH® Playback........................................................25 Network Functions..................................................................26 USB Storage Device...............................................................27 Listening to the AM/FM Radio................................................28 Multi-zone...............................................................................30 Listening Mode.......................................................................31 The Basic Manual includes information needed when starting up and also instructions for frequently used operations. The Advanced Manual has more detailed information and advanced settings. AV RECEIVER TX-NR777 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Before Start What's in the box 1. Main unit (1) 1 2 3 4 5 6 2. Remote controller (RC-911R) (1), Batteries (AAA/R03) (2) 3. Speaker setup microphone (1) 0 Used during Initial Setup. 4. Indoor FM antenna (1) 5. AM loop antenna (1) 6. Power cord (1) 0 Quick Start Guide (1) 0 Basic Manual (This manual) 0 Connect speakers with 4 Ω to 16 Ω impedance. When connecting speakers to both ZONE 2A and ZONE 2B (P21), both sets of speakers connected in ZONE 2 should have 8 Ω to 16 Ω impedance. 0 The power cord must be connected only after all other cable connections are completed. 0 We will not accept responsibility for damage arising from the connection of equipment manufactured by other companies. 0 Functionality may be introduced by firmware updates and service providers may cease services, meaning that some network services and content may become unavailable in the future. Furthermore, available services may vary depending on your area of residence. 0 Details on the firmware update will be posted on our website and through other means at a later date. 0 Specifications and appearance are subject to change without prior notice. 2 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Part Names Part Names         (*)You can find details in the Advanced Manual.      Front Panel      turned off completely. 1. Í ON/STANDBY button 2. MUSIC OPTIMIZER button/indicator: Turns on/off the Music Optimizer function that provides better sound quality for compressed audio. 3. HYBRID STANDBY indicator: Lights if the unit enters standby mode when the features are enabled that continue to work when this unit is in standby, such as HDMI Standby Through and Network Standby. 4. Remote control sensor: Receives signals from the remote controller. 0 The signal range of the remote controller is within about 16´/5 m, at an angle of 20° on the perpendicular axis and 30° to either side. 5. ZONE 2 button: Controls the multi-zone function (P30). 6. OFF button: Switches the multi-zone function off (P30). 7. DIMMER button: You can adjust the brightness of the display in three steps. It cannot be 8. Display (P4) 9. SETUP button: You can show advanced setting items on the TV and display to provide you with an even better experience. (*) 10.Cursor buttons (⌤ / ⌃ / ⍽ / ⇪) and ENTER button: Select the item with the cursors and press ENTER to confirm. Use them to tune to stations when using TUNER (P28). 11. RETURN button: Returns the display to the previous state. 12.MASTER VOLUME 13.Press the LISTENING MODE button (above) repeatedly to select a category from "Movie/ TV", "Music", "Game", then turn the LISTENING MODE dial (below) to change the mode (P31). (*) En 3 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual. 14.You can adjust the sound quality of the front speakers. Press the TONE button (above) repeatedly to select the item to adjust from "Bass" and "Treble", and turn the TONE dial (below) to adjust. 15.PHONES jack: Headphones with a standard plug (Ø1/4"/6.3 mm) are connected. 16.Input selector buttons: Switches the input to be played. 17.SETUP MIC jack: The supplied speaker setup microphone is connected. 18.AUX INPUT AUDIO/HDMI jack: Connect a video camera, etc., using a stereo mini plug cable (Ø1/8"/ 3.5 mm) or a HDMI cable.        Display 1. Speaker/Channel display: Displays the output channel that corresponds to the selected listening mode. 2. Lights in the following conditions. Ë: When headphones are connected. Z2: When ZONE 2 is on. : When connected by BLUETOOTH. : When connected by Wi-Fi. NET: When "NET" is selected with the input selector and the unit is connected to the network. It will flash if the connection to the network is not correct. USB: When "NET" is selected with the input selector and the unit is connected by USB and the USB device is selected. Flashes if the USB is not properly connected. HDMI: When HDMI signals are input and the HDMI input is selected. DIGITAL: When digital signals are input and the digital input is selected. 3. Lights according to the type of input digital audio signals and the listening mode. 4. Lights in the following conditions. TUNED: Receiving AM/FM radio. FM ST: Receiving FM stereo. SLEEP: When the sleep timer is set. (*) AUTO STBY: Auto Standby is on. (*) 5. Flashes when muting is on. 6. Displays various information of the input signals. Characters that cannot be displayed on this unit are replaced with asterisks ( * ). 0 When playing back software which has been encoded in Dolby Digital, Dolby Digital Plus and Dolby TrueHD, sometimes you may see a brief message which will read "DialogNorm: X dB" (X being a numeric value). For example, if you see the following message: "DialogNorm:+4 dB", to keep the overall output level at THX calibrated loudness, just turn down the volume control by 4 dB. 7. This may light when performing operations with the "NET" input selector. 4 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual.  Rear Panel             90° 180°        to a monitor such as a TV or projector. 1. DIGITAL IN OPTICAL/COAXIAL jacks: Input TV or AV component digital audio signals with a digital optical cable or digital coaxial cable. 2. TUNER AM/FM 75Ω terminal: The supplied antennas are connected. 3. VIDEO IN jacks: Input the AV component video signals with an analog video cable. 4. Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTH wireless technology enabled device. Adjust their angles according to the connection status. 5. USB port: A USB storage device is connected so that music files stored in it can be played. You can also supply power (5 V/1 A) to USB devices with a USB cable. 6. ETHERNET port: Connect to the network with an Ethernet cable. 7. COMPONENT VIDEO IN jacks: Input the AV component video signals with a component video cable. (Compatible only with 480i or 576i resolution.) 8. HDMI OUT jacks: Transmit video signals and audio signals with a HDMI cable connected 9. HDMI IN jacks: Transmit video signals and audio signals with a HDMI cable connected to an AV component. 10.RS232 port: For connection to the home control system. (*) 11.AC INLET: The supplied power cord is connected. 12.GND terminal: The ground wire of the turntable is connected. 13.AUDIO IN jacks: Input TV or AV component audio signals with an analog audio cable. 14.SPEAKERS terminals: Use a speaker cable to connect multichannel speakers for the main room and speakers for a separate room (ZONE 2). (Compatible with banana plugs) 15.ZONE 2 LINE OUT jack: Output audio signals with an analog audio cable to a pre-main amplifier in a separate room (ZONE 2). En 5 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual. 16.SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a subwoofer cable. Up to two powered subwoofers can be connected. The same signal is output from each of the SUBWOOFER PRE OUT jacks. 17.12V TRIGGER OUT jack: Allows you to connect a device with 12V trigger input jack to enable link operation between the device and the unit. (*) 18.IR IN port: Allows you to connect a multiroom remote control kit. (*)           Remote Controller 1. Í ON/STANDBY button 2. Input selector buttons: Switches the input to be played. 3. Q (QUICK MENU) button: Settings such as "Tone" and "Level" can be made quickly during play on the TV screen. "Other" has settings to switch the speakers given priority for output and to switch HDMI output (P16). (*) 4. Cursor buttons and ENTER button: Select the item with the cursors and press ENTER to confirm your selection. When the folder or file lists are not shown on one screen on the TV, press ⍽ / ⇪ to change the screen. 5. button: You can show advanced setting items on the TV and display to provide you with an even better experience. (*)  6. Volume buttons 7. button: Temporarily mutes audio. Press again to cancel muting. 8. LISTENING MODE buttons: Allows you to select the listening mode (P31). (*) MAIN/ZONE 2 buttons: Controls the multi-zone function (P30). (The ZONE 3 button is not used with this unit.) 9. Play buttons: Used for play operations when playing Music Server or USB. 10. button: You can start repeat/random play of the Music Server or USB. Each time you press the button, the mode switches from (1-track repeat), to  (folder repeat), to (random). CLEAR button: Deletes all characters you have entered when entering text on the TV screen. 11. button: Switches the information on the display. 12. button: Returns the display to the previous state. 13.MODE button: Switches tuning to an AM/FM station between automatic tuning and manual tuning (P28), and also used to control the multi-zone feature (P30). 14.MEMORY button: Used to register AM/FM radio stations. Tips When the remote controller isn't working: The remote controller may have switched to the mode for controlling ZONE 2. While holding down MODE, press MAIN for 3 seconds or more until the remote indicator flashes once to switch it to  the mode to control the main room.  6 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Install Installation procedure 1 2 3 This unit can be used in a number of ways, depending on the layout of the speakers you are installing, and the connections made to external devices. Read the following to help make the installation process smoother. Step1: Speaker Layout Select the speaker layout that suits the types of speakers you have and the conditions they will be used in from the choices presented on pages P8 to P12, then install the speakers by referring to the illustrations and explanations on the relevant page. Speaker layouts include systems that use surround back speakers, systems that use height speakers, and systems that use Bi-Amping speakers. Also refer to the combinations available in "Speaker combinations" on P13. Step2: Connect the Speakers To connect the speaker systems to this unit, refer to P14 if you are using a speaker layout described on one of P8 to P11, and to P15 to use a speaker layout using Bi-Amping speakers described on P12. The connection process will be smoother if you refer to the illustrations and explanations and prepare the required cables before hand. Step3: Connect the TV & AV Components Refer to P16 to P22 to connect your external devices such as your TV, Blu-ray Disc Player, and also supplied accessories such as the antennas. Also, P20, P21 introduces the Multi-zone Connection option that allows you to play audio into rooms other than the main room. The connection process will be smoother if you refer to the illustrations and explanations, confirm the connection types on the external devices, and prepare the required cables before hand. En 7 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Step1: Speaker Layout 7.1 Channel System Front speakers output front stereo sound and a center speaker outputs center sound such as dialogs and vocals. Surround speakers create back sound field. Powered subwoofer reproduces bass sounds and creates rich sound field. This basic 5.1 Channel System with surround back speakers added is called a 7.1 Channel System. The connection of surround back speakers improves the sense of envelopment and connectivity of sound created by the back sound field and provides a more real sound field. Furthermore, by installing surround back speakers, you can select the Dolby Atmos listening mode, which realizes the *1 *2 *3 ⯋1: 22e to 30e, ⯋2: 90e to 110e, ⯋3: 135e to 150e most up-to-date 3D sound, when the input format is Dolby Atmos. The front speakers should be positioned at ear height, while the surround speakers should be positioned just above ear height. Center speaker should be set up facing the listening position. Placing the powered subwoofer between the center speaker and a front speaker gives you a natural sound even when playing music. The optimal positioning is for surround back speakers to be at ear height. 0 If you are including surround back speakers in the setup, surround speakers are required. 0 "Speaker combinations" (P13) introduces some detailed examples of speaker combinations. 1,2 Front Speakers 3 Center Speaker 4,5 Surround Speakers 6 Powered Subwoofer 7,8 Surround Back Speakers 8 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 5.1.2 Channel System-1 (Front High Speakers/Rear High Speakers) This is a basic 5.1 channel system consisting of front speakers, a center speaker, surround speakers, and a powered subwoofer, with the addition of front height 3´ (0.9 m) or more ⯋1: 22e to 30e, ⯋2: 120e *1 *2 3´ (0.9 m) or more speakers or rear high speakers, which are both types of height speakers. By installing height speakers, you can select the Dolby Atmos listening mode, which realizes the most up-to-date 3D sound including overhead sounds, when the input format is Dolby Atmos. Front high speakers or rear high speakers should be situated at least 3´/0.9 m higher than the front speakers. Front high speakers should be situated directly above the front speakers and the distance between the rear high speakers should match the distance between the front speakers. Both should be set up facing the listening position. 0 "Speaker combinations" (P13) introduces some detailed examples of speaker combinations. 7,8 Height Speakers Choose one of the following: 0 Front High Speakers 0 Rear High Speakers En 9 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 5.1.2 Channel System-2 (Ceiling Speakers) This is a basic 5.1 channel system consisting of front speakers, a center speaker, surround speakers, and a powered subwoofer, with the addition of top front speakers, top middle speakers, or top rear speakers, which are types of height speakers. By installing height speakers, you can select the Dolby Atmos listening mode, which realizes the most up-to-date 3D sound including overhead sounds, when the input format is Dolby Atmos. Fit top front speakers *3 *2 *1 ⯋1: 30e to 55e, ⯋2: 65e to 100e, ⯋3: 125e to 150e on the ceiling forward of the seating position, top middle speakers on the ceiling directly above the seating position, and top rear speakers on the ceiling behind the seating position. The distance between each pair should match the distance between the two front speakers. 0 Dolby Laboratories recommends placing this type of height speakers to obtain the best Dolby Atmos effect. 0 "Speaker combinations" (P13) introduces some detailed examples of speaker combinations. 7,8 Height Speakers Choose one of the following: 0 Top Front Speakers 0 Top Middle Speakers 0 Top Rear Speakers 10 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 5.1.2 Channel System-3 (Dolby Enabled Speakers (Dolby Speakers)) This is a basic 5.1 channel system consisting of front speakers, a center speaker, surround speakers, and a powered subwoofer, with the addition of Dolby enabled speakers (front) or Dolby enabled speakers (surround), which are both types of height speakers. Dolby enabled speakers are special speakers designed to face the ceiling so that sound is heard after bouncing off the ceiling so that sound appears to be coming from overhead. By installing height speakers, you can select the Dolby Atmos listening mode, which realizes the most up-to-date 3D sound *1 *2 ⯋1: 22e to 30e, ⯋2: 120e including overhead sounds, when the input format is Dolby Atmos. Place them either above the front speakers or above the surround speakers. 0 "Speaker combinations" (P13) introduces some detailed examples of speaker combinations. 7,8 Height Speakers Choose one of the following: 0 Dolby Enabled Speakers (Front) 0 Dolby Enabled Speakers (Surround) En 11 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Bi-Amping the Speakers With a 5.1 channel system, it is possible to connect front speakers that support Bi-Amping to improve the quality of the bass and treble. Bi-Amping compatible speakers need their terminals for the tweeters connected to one amplifier and their terminals for woofers connected to another amplifier, so it is not possible to connect height speakers and surround back speakers with this connection. Other than front speakers, you can also connect a center speaker, surround speakers, and a powered subwoofer. 0 "Speaker combinations" (P13) introduces some detailed examples of speaker combinations. *1 *2 ⯋1: 22e to 30e, ⯋2: 120e 1,2 Front Speakers (Bi-Amping) 3 Center Speaker 4,5 Surround Speakers 6 Powered Subwoofer 12 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Speaker combinations 0 In any of the combinations, up to two powered subwoofers can be connected. Speaker Channels FRONT CENTER SURROUND SURROUND BACK HEIGHT Bi-AMP ZONE 2 (ZONE SPEAKER) (P21) 2.1 ch (*1) (*1, 2) 3.1 ch (*1) (*1, 2) 4.1 ch (*1) (*1, 2) 5.1 ch (*1) (*1, 2) 6.1 ch (*3) 7.1 ch (*3) 2.1.2 ch (*4) 3.1.2 ch (*4) 4.1.2 ch (*4) 5.1.2 ch (*4) (*1) You can select Bi-AMP or ZONE SPEAKER. (*2) You can connect two sets of ZONE SPEAKER; ZONE 2A and ZONE 2B. (*3) No sound is played from the surround back speakers when playing audio from ZONE SPEAKER. (*4) No sound is played from the height speakers when playing audio from ZONE SPEAKER. En 13 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Step2: Connect the Speakers Standard Connections (Pages 8 to 11) Up to two powered subwoofers can be connected. The same signal is output from each of the SUBWOOFER PRE OUT jacks. Setup 1/2˝ (12 mm) b a a Speaker cable, b Subwoofer cable 0 Settings for the speaker configuration you have connected need to be made in "1. AccuEQ Room Calibration" in Initial Setup (P23). 0 If any of the connected speakers have an impedance of 4 Ω or more to less than 6 Ω, after completing Initial Setup, you need to make some settings in the Setup menu. Press on the remote controller, select "2. Speaker" - "Configuration" and set "Speaker Impedance" to "4ohms". Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear panel or the + and – wires touch each other, the protection circuit will be activated. 14 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Connecting with Bi-Amping Speakers (Page 12) Make sure you remove the jumper bar fitted between the woofer jacks and tweeter jacks of the front speakers. Refer to "Standard Connections (Pages 8 to 11)" (P14) to connect the center speaker, surround speakers, and powered 1/2˝ (12 mm) a For high frequency For low frequency a Speaker cable subwoofer. 0 Also refer to the instruction manual for your speakers when using connections for Bi-Amping. Setup 0 Settings for the speaker configuration you have connected need to be made in "1. AccuEQ Room Calibration" in Initial Setup (P23). 0 If any of the connected speakers have an impedance of 4 Ω or more to less than 6 Ω, after completing Initial Setup, you need to make some settings in the Setup menu. Press on the remote controller, select "2. Speaker" - "Configuration" and set "Speaker Impedance" to "4ohms". Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear panel or the + and – wires touch each other, the protection circuit will be activated. En 15 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Step3: Connect the TV & AV Components 1. Connect the TV To ARC TV *2 a b TV For a TV that supports the ARC (Audio Return Channel) (*1) feature, use an HDMI cable and connect according to illustration "a". Choose an HDMI IN jack on the TV that supports ARC when connecting. Setup 0 Settings are required to use the ARC function. Select "Yes" in "5. Audio Return Channel" (P24) in the Initial Setup. 0 Refer to the instruction manual for the TV for TV connections and instructions regarding settings for CEC features and audio output. To Non-ARC TV For a TV that does not support the ARC (Audio Return Channel) feature (*1), connect both the HDMI cable in illustration "a" and the digital optical cable in "b". If the TV doesn't have a DIGITAL OPTICAL OUT jack, use an analog audio cable and connect the TV's ANALOG AUDIO OUT jack to the AUDIO IN TV jack on this unit. 0 Connection with a digital optical cable is not necessary if you will watch TV through a device such as a cable set top box (that is, not use a tuner built into the TV) that you have connected to the input jack on this unit. (*1) The ARC feature: This feature transfers TV audio signals via HDMI cable so that you can play the audio from the TV through this unit. Connection to an ARC compatible TV is complete with one HDMI cable. Refer to the instruction manual for your TV to see if it supports ARC. (*2) Another TV or projector can be connected to the HDMI OUT SUB jack. Press Q (P6) on the remote control and use "Other" - "HDMI Out" to switch between MAIN and SUB. Note that this jack does not support ARC. a HDMI cable, b Digital optical cable 16 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 2. Connect the HDMI AV Component This is an example of connection with an AV component that has an HDMI jack. With connection to an AV component that conforms with the CEC (Consumer Electronics Control) standard, you can use features such as the HDMI CEC feature (*) that links with the input selector, and the HDMI Standby Through feature which allows you to play video and audio from AV components on the TV even when this unit is in standby mode. 0 To play 4K or 1080p video, use a high speed HDMI cable. Setup 0 When "Yes" is selected for "5. Audio Return Channel" in Initial Setup (P24), the HDMI CEC function and HDMI Standby Through function are automatically enabled. If "No, Skip" is selected, settings are required in the Setup menu after Initial Setup is complete. Press on the remote controller and make the settings in "5. Hardware" - "HDMI". 0 To enjoy digital surround sound including Dolby Digital, audio output should be set to "Bitstream output" on the connected Blu-ray Disc player or other device. (*)The HDMI CEC feature: You can control features such as linking input switching with the input selector and BD/DVD GAME Cable/Satellite set-top a Streaming media players conforming to the CEC standard, switching audio to output it from the TV or from this unit, and adjusting the volume using the remote controller of a CEC compliant TV, and automatically switching this unit to standby when the TV is turned off. player a HDMI cable box En 17 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 3. Connect the Non-HDMI AV Component This is an example of connection with an AV component that does not have an HDMI jack. Make the connections to the AV component to match the jacks it has. When video input connection is to the BD/DVD jack, the audio input connection should also be to the BD/DVD jacks, and so on, so that you connect the video input jacks to the jacks with the same name as the audio input jacks. Note that video signals input to the VIDEO IN jack or the COMPONENT VIDEO IN jack will be converted to HDMI video signals and then output from the HDMI OUT jack. 0 To enjoy digital surround playback in formats such as Dolby Digital, you need to make a connection for audio signals with a digital coaxial cable or a digital optical cable. 0 It is possible to change assignment of the input jacks you see in the illustration at left, so you can also connect to any jack other than BD/DVD. For details, see the Advanced Manual. Setup 0 The COMPONENT VIDEO IN jacks are compatible only with 480i or 576i resolution. When you connect to the COMPONENT VIDEO IN jacks, set the output resolution of the player to 480i or 576i. Select interlace if there is no option a b OR c BD/DVD for 480i, etc. If your player does not support 480i or 576i output, use the VIDEO IN jack. 0 To enjoy digital surround sound including Dolby Digital, audio output should be set to "Bitstream output" on the connected Blu-ray Disc player or other device. a Component video cable, b Digital coaxial cable, c Analog audio cable 18 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 4. Connect the Audio Component Example of a connection with an audio component. Connect a CD player using a digital optical cable or analog audio cable. You can also connect a turntable that has an MM-type cartridge to the PHONO jack. 0 If the turntable has a built-in audio equalizer, connect it to another AUDIO IN jack. Further, if the turntable uses an MC type cartridge, install an audio equalizer compatible with the MC type cartridge between the unit and the turntable, then connect to any AUDIO IN jack other than the PHONO jack. If the turntable has a ground wire, connect it to the GND terminal of this unit. a OR b CD Turntable a Digital optical cable, b Analog audio cable En 19 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 5. Multi-zone Connection-1 (ZONE 2 LINE OUT) You can enjoy 2ch audio in the separate room through speakers connected to a pre-main amplifier by, for example, playing a Blu-ray Disc player in 7.1 ch in the main room (where this unit is located) and listening to internet radio in the separate room (ZONE 2). Connect the ZONE 2 LINE OUT jacks of the unit and the LINE IN jacks of the pre-main amplifier in a separate room with an analog audio cable. 0 DSD and Dolby TrueHD audio signals are not output to ZONE 2 when selected with the "NET" input selector. Connections with an AV component When outputting the audio of an externally connected AV component to ZONE 2, you need to connect using a digital b a OR MAIN ROOM ZONE2 LINE IN coaxial cable, digital optical cable, or analog audio cable. Setup 0 Settings are required in Initial Setup, "4. Multi Zone Setup" (P24) to enjoy this feature. 0 The audio from externally connected AV components can only be played in ZONE 2 when the audio is analog or 2ch PCM audio. If you have connected to this unit with a digital coaxial cable or digital optical cable, it may be necessary to change the audio output of the AV component to PCM output. BD/DVD ZONE2 LINE OUT a Digital coaxial cable, b Analog audio cable 20 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. ZONE 2B ZONE 2A (Also act as the SURROUND BACK or HEIGHT jacks) MAIN ROOM c b 6. Multi-zone Connection-2 (ZONE SPEAKER) You can enjoy 2ch audio in the separate room by, for example, playing a Blu-ray Disc player in the main room (where this unit is located) and listening to internet radio through the speakers in the separate room (ZONE 2). You can connect up to two speaker systems and output the same audio. To connect one speaker system, use the ZONE 2A jacks, and to connect two speaker systems, use the ZONE 2B jacks in addition to the ZONE 2A jacks. When connecting two speaker systems, all speakers to be connected to the ZONE 2A/B jacks must have an impedance of 8 to 16 Ω. 0 You cannot use ZONE SPEAKER if you have connected the front speakers using Bi-Amping connection. 0 Please note that it is not possible to connect to the ZONE 2B jacks when surround back speakers or height speakers are connected. 0 No sound is played from the surround back speakers or the height speakers when playing audio from ZONE SPEAKER. Connections with an AV component When outputting the audio of an externally connected AV component to ZONE 2, you need to connect using a digital coaxial cable, digital optical cable, or analog audio cable. Setup 0 Settings are required in Initial Setup, "4. Multi Zone Setup" (P24) to enjoy this feature. a BD/DVD OR ZONE 2 SPEAKER A ZONE 2 SPEAKER B 0 To use the ZONE 2A+B output, set "Zone Speaker" in "1. AccuEQ Room Calibration" (P23) in Initial Setup to "Zone 2A + B". 0 The audio from externally connected AV components can only be played in ZONE 2 when the audio is analog or 2ch PCM audio. If you have connected to this unit with a digital coaxial cable or digital optical cable, it may be necessary to change the audio output of the AV component to PCM output. a Digital coaxial cable, b Analog audio cable, c Speaker cable En 21 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 7. Connect Other Cables Antenna Hookup Move the antenna around while playing the radio to find the position with the best reception. Use a thumb tack or similar to attach the indoor FM antenna to a wall. a d c a 2 b Network Hookup Connect this unit to the network using wired LAN or Wi-Fi (wireless LAN). You can enjoy network features such as internet radio by connecting the unit to the network. If you connect by wired LAN, connect with an Ethernet cable to the ETHERNET port as shown in the illustration. To connect by Wi-Fi, then after selecting "Wireless" in "3. Network Connection" (P24) in Initial Setup, select the desired setting method and follow the onscreen instructions to configure the connection. Power Cord Hookup This unit includes removable power cords. Connect the power cord to the power outlet after completing all other connections. Connect the power cord to AC INLET of the unit and then connect to the outlet. Always disconnect the outlet side first when disconnecting the power cord. a AM loop antenna, b Indoor FM antenna, c Ethernet cable, d Power cord 22 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Initial Setup Initial Setup with Auto Start-up Wizard 1 INPUT T V Initial Setup Starts Automatically When you turn the unit on for the first time after purchasing it, Initial Setup is automatically shown on the TV to enable you to make settings required for startup using simple operations following onscreen guidance. 1. Switch the input on the TV to that assigned to the unit. 2. Put batteries into the remote controller of this unit. 3. Press Í on the remote controller to turn the unit on. 4. Select the item with the cursors of the remote controller and press ENTER (a) to confirm your selection. To return to the previous screen, press (b). a 2 3 b 0 If you terminate the procedure on the way or want to change a setting made during Initial Setup, press on the remote controller, select "7. Miscellaneous" – "Initial Setup", and press ENTER. ∫ 1. AccuEQ Room Calibration Place the supplied speaker setup microphone in the listening position, measure the test tones emitted by the speakers, then the unit automatically sets the optimum volume level for each speaker, the crossover frequencies, and the distance from the listening position. This also automatically adjusts the equalizers for the speakers and enables correction of distortion caused by the acoustic environment of the room. 0 Calibration takes between 3 and 12 minutes to be completed. The speakers emit the test tone at high volume during measurement, so be careful of your surroundings. En 23 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Keep the room as quiet as possible during measurement. 0 If you have connected a subwoofer, check the power and volume of the subwoofer. Set the subwoofer volume to more than halfway. 0 If the power of this unit suddenly turns off, the wires in the speaker cables may have touch the rear panel or other wires and tripped the protection circuit. Twist the wires again properly and make sure they do not stick out of the speaker terminals when connecting. 0 When using THX certified speakers, THX recommends setting the crossover frequency to "80Hz(THX)". It is also recommended to manually adjust the settings for each speaker to suit the specific characteristics of each room. 1. Place the supplied speaker setup microphone in the listening position, and connect to the SETUP MIC jack on the main unit. SETUP MIC When putting the speaker setup microphone on a tripod, refer to the illustration when putting it in place. 2. Select the connected speaker configuration. AccuEQ Room Calibration The image on the screen changes as you choose the number of channels in "Speaker Channels", so refer to it when performing the settings. 3. Test tones are emitted by the speakers, and firstly the unit detects the speakers connected and the noise in the environment. 4. After the results of the above measurements are displayed, select "Next", press ENTER on the remote controller, and the test tones are emitted again, and the unit automatically makes settings such as the optimum volume level and the crossover frequency. 5. When the measurement is completed, the measurement result is displayed. Press the cursors ⍽ / ⇪ on the remote controller to check the settings. Press ENTER when "Save" is selected to save the settings. 6. Select whether to enable or disable the equalizer function that corrects for distortion caused by the acoustic environment of the room. If this is to be enabled, then normally you should select "On (All Channels)", and to disable just the front speakers you should select "On (Except Front Left / Right)". 7. Disconnect the speaker setup microphone. ∫ 2. Source Connection Check that each input source is connected correctly. Follow the guidance, select the input you want to confirm, start play of the selected player, and confirm that the images appear on the TV and that sound is played. ∫ 3. Network Connection Set up Wi-Fi connection with an access point such as a If you select "Scan Networks", there are a further two choices of connection method. Check the following. "Enter Password": Enter the password (or key) of the access point to connect. "Push Button": If the access point has an automatic connection button, you can connect without entering a password. 0 If the SSID of the access point is not displayed, then in the screen listing the SSIDs, select "Other..." with the ⇪ cursor on the remote controller and press ENTER, then follow the onscreen instructions. Keyboard Input To switch between upper and lower case, select "A/a" on the screen and press ENTER. To select whether to mask the password with "⯋" or display it in plain text, press MEMORY on the remote controller. Press CLEAR to delete all the input characters. 0 A confirmation screen asking you to agree to the privacy policy is displayed during network setting. Select "Accept" and press ENTER to indicate agreement. ∫ 4. Multi Zone Setup When you want to enjoy audio in a room other than the main room, set the audio output method for the separate room (ZONE 2). If you have connected speakers in a separate room with speaker cable, select "Using AV Receiver". If you have connected a pre-main amplifier in a separate room with an analog audio cable, select "with External Premain Amplifier". Speaker Channels Subwoofer Height Speaker Zone Speaker Bi-Amp 7.1 ch < > Yes --- No No wireless LAN router. There are the following two methods of connecting by Wi-Fi: "Scan Networks": Search for an access point from this unit. Find out the SSID of the access point beforehand. ∫ 5. Audio Return Channel If you have connected a TV that supports ARC, select "Yes". This unit's ARC setting turns on and you can listen to the TV's audio through this unit. Select how many speakers you have. Next "Use iOS Device (iOS7 or later)": Share the iOS device's Wi-Fi settings with this unit. 0 If you select "Yes", the HDMI CEC function is enabled and power consumption increases during standby. 24 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Playback AV Component Playback 1 2 INPUT T V BLUETOOTH® Playback 1 2 3 Onkyo TX-NR777 XXX Basic Operations You can play the audio from AV components such as Blu-ray Disc players through this unit. 0 When a TV is connected to the HDMI OUT SUB jack, press Q (P6) on the remote controller and use "Other" - "HDMI Out" to switch between MAIN and SUB. Perform the following procedure when the unit is on. 1. Switch the input on the TV to that assigned to the unit. 2. Press the input selector (a) on the remote controller with the same name as the jack to which you connected the player to switch the input. For example, press BD/DVD to play the player connected to the BD/DVD jack. Press TV to listen the TV's sound.To play a device connected to the AUX INPUT AUDIO/HDMI jack on the front panel, press AUX. 0 When the CEC link function works, the input switches automatically when you have connected a CEC compliant TV and player to this unit using HDMI connection. 3. Start play on the AV component. a You can wirelessly play music on a smartphone or other BLUETOOTH wireless technology enabled device. Perform the following procedure when the unit is on. Pairing 1. When you press the button, "Now Pairing..." is displayed on this unit's display, and the pairing mode is enabled. 2. Enable (turn on) the BLUETOOTH function of the BLUETOOTH wireless technology enabled device, then select this unit from amongst the devices displayed. If a password is requested, enter "0000". 0 This unit is displayed as "Onkyo TX NR777 XXXXXX". 0 To connect another BLUETOOTH wireless technology enabled device, press and hold until "Now Pairing..." is displayed, then perform step 2. This unit can store the data of up to 8 paired devices. 0 The coverage area is 48´/15 m. Note that connection is not always guaranteed with all BLUETOOTH wireless technology enabled devices. Playing Back 1. Perform the connection procedure on the BLUETOOTH wireless technology enabled device. The input on this unit automatically switches to "BLUETOOTH". 2. Play music. Increase the volume of the BLUETOOTH wireless technology enabled device to an appropriate level. 0 Due to the characteristics of BLUETOOTH wireless technology, the sound produced on this unit may slightly be behind the sound played on the BLUETOOTH wireless technology enabled device. En 25 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Network Functions 1 3 2 INPUT T V Basic Operations By connecting this unit to the network you can enjoy internet radio services such as TuneIn, streaming from Spotify Connect, and wireless playback using AirPlay® features. Furthermore, you can use the Music Server feature to stream music files stored on PCs or NAS devices that support the home network feature. The basic operations for Network Functions are introduced in the Basic Manual. For more advanced operations, see the Advanced Manual. There may also be additional network functions provided through firmware updates for this unit. Also see the Advanced Manual for information about new features. 0 The network needs to be connected to the internet in order to play internet radio services. 0 Depending on the internet radio service, the user may need to register from their computer first. 0 To enable Spotify Connect, install the Spotify application on your smartphone or tablet and create a Spotify premium account. – Refer to the following for Spotify settings: spotify.com/connect/ 0 The network servers compatible with the Music Server feature are those PCs with players installed that have the server functionality of Windows Media® Player 11 or 12, or NAS that are compatible with home network functionality. Note that with PCs, only music files registered in the library of Windows Media® Player can be played. 0 You may need to make some settings on the PC in advance to use Windows Media® Player 11 or 12 with the Music Server feature. Perform the following procedure when the unit is on. 1. Switch the input on the TV to that assigned to the unit. 2. Press NET (a) on the remote controller to display a list of Network Functions on the TV. 3. Select the Network Function with the cursors of the remote controller and press ENTER (b) to confirm your a selection. With internet radio services, follow the on-screen instructions, using the cursors b to select radio stations and programs, then press ENTER to play. With Spotify or AirPlay, select this unit with your smartphone to play. With Music Server, c select the server with the cursors, then select the desired music file and press ENTER to play. 0 To return to the previous screen, press (c). 26 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. USB Storage Device 1 3 4 2 INPUT T V Basic Operations You can play music files stored on a USB storage device. Perform the following procedure when the unit is on. 1. Switch the input on the TV to that assigned to the unit. 2. Plug your USB storage device with the music files into the USB port of this unit’s rear panel. 3. Press NET (a) on the remote controller to display the network service list screen. 4. With the cursors on the remote controller, select "USB", and then press ENTER (b). 0 If the "USB" indicator flashes on the display, check whether the USB storage device is plugged in properly. 0 Do not unplug the USB storage device while "Connecting···" is appeared on the display. This may cause data corruption or malfunction. 5. Press ENTER on the remote controller again in the next screen. The list of folders and music files on the USB storage device are displayed. Select the folder with the cursors and press ENTER a to confirm your selection. 6. With the cursors on the remote controller, select the music file, and then b press ENTER to start playback. 0 To return to the previous screen, press (c). 0 The USB port of this unit conforms with the USB 2.0 standard. The transfer speed may be insufficient for some content you play, which may cause some interruption in sound. 0 Operation cannot be guaranteed for all USB storage devices. 0 This unit can use USB storage devices that comply with the USB mass storage class standard. The unit is also compatible with USB storage devices using the FAT16 or FAT32 file system formats. c En 27 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Listening to the AM/FM Radio 1 2 3 You can receive AM and FM radio stations on this unit with the built-in tuner. Perform the following procedure when the unit is on. ∫ Tuning into a Radio Station Tuning Automatically 1. Press TUNER (a) on the remote controller repeatedly to select either "AM" or "FM" on the display. 2. Press MODE (e) on the remote controller, so that the "TunMode: Auto" is displayed on the display. 3. When you press the cursors ⌤ / ⌃ buttons (b) on the remote controller, automatic tuning starts, and searching stops when a station is found. When tuned into a radio station, the "TUNED" indicator on the display lights. When tuned into an FM stereo station, the "FM ST" indicator lights. When FM broadcasts reception is poor: Perform the procedure for "Tuning Manually" in the following section. Note that if you tune manually, the reception for FM broadcasts will be monaural rather than stereo, irrespective of the sensitivity of the reception. Tuning Manually Note that if you tune manually, the reception for FM broadcasts will be monaural rather than stereo, irrespective of the sensitivity of the reception. 1. Press TUNER (a) on the remote controller repeatedly to select either "AM" or "FM" on the display. 2. Press MODE (e) on the remote controller, so that the "TunMode: Manual" is displayed on the display. 3. While pressing the cursors ⌤ / ⌃ (b) on the remote controller, select the desired radio station. 0 The frequency changes by 1 step each time you press the cursors ⌤ / ⌃. The frequency changes continuously if the button is held down and stops when the button is released. Frequency step setting: Press the button, the cursor buttons and ENTER on the remote controller to select "7. Miscellaneous" – "Tuner" – "AM/FM Frequency Step" and select the frequency step for your area. Note that when this setting is changed, all radio presets are deleted. a b c de 28 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 1 2 3 ∫ Presetting a Radio Station It allows you to register up to 40 of your favorite AM/FM radio stations. Registration Procedure After tuning into the AM/FM radio station you want to register, perform the following procedure. 1. Press MEMORY (d) on the remote controller so that the preset number on the display flashes. 2. While the preset number is flashing (about 8 seconds), repeatedly press the cursors ⍽ / ⇪ (b) on the remote controller to select a number between 1 and 40. 3. Press MEMORY again on the remote controller to register the station. When registered, the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations. Selecting a Preset Radio Station 1. Press TUNER (a) on the remote controller. 2. Press cursors ⍽ / ⇪ (b) on the remote controller to select a preset number. Deleting a Preset Radio Station 1. Press TUNER (a) on the remote controller. 2. Press cursors ⍽ / ⇪ (b) on the remote controller to select the preset number to delete. 3. After pressing MEMORY (d) on the remote controller, press CLEAR (c) while the preset number is flashing to delete the preset number. When deleted, the number on the display goes off. En 29 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Multi-zone 1 2 3 To return the remote controller to main room control mode: While holding down MODE on the remote controller, press MAIN (c) for 3 seconds or more until the remote indicator flashes once. a b Basic Operations You can enjoy audio in the separate room by, for example, playing a Blu-ray Disc player in the main room (where this unit is located) and listening to internet radio in the separate room (ZONE 2). 0 DSD and Dolby TrueHD audio signals are not output to ZONE 2 when selected with the "NET" input selector. 0 You can only select the same inputs for the main room and separate room with the "NET" or "BLUETOOTH" input selector. If you have "NET" selected in the main room and then select "BLUETOOTH" in the separate room, the main room also switches to "BLUETOOTH". You cannot select different stations for the main room and separate room with the AM/FM radio. 0 If ZONE 2 is on, power consumption during standby becomes larger than normal. Perform the following procedure when the unit is on. 1. While holding down MODE (e) on the remote controller, press ZONE 2 (d) for 3 or more seconds until the remote indicator blinks twice. 0 The remote controller switches to the mode for controlling ZONE 2. 2. Point the remote controller at the main unit and press Í (a). "Z2" lights on the main unit display. 3. Press the input selector button (b) of the input to be played in the separate room. 0 On the main unit, after pressing ZONE 2, within 8 seconds press the input selector button to select the input to be played in the separate room. To play the same source in the main room and separate room, press ZONE 2 on the main unit twice. 4. Volume adjustment is done on the pre main amplifier for the separate room when connected via ZONE 2 LINE OUT. When outputting from ZONE speakers, adjust with volume buttons on the remote controller. 0 To control on the main unit, press ZONE 2 and adjust with the MASTER VOLUME control within 8 seconds. To turn off the function: Press Í while in the mode for controlling ZONE 2 on the remote controller. Alternatively press OFF on the main unit. c Playing in ZONE 2 only: If you turn the unit to standby during multi zone playback, the Z2 indicator is dimmed and the playback mode is switched to playback in a separate room only. Setting ZONE 2 to on while this unit is in standby will also switch the playback mode to the same setting. d e 30 > Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Listening Mode This unit is equipped with a variety of listening modes, and you can select the optimum listening mode for movies, TV, music, and games using MOVIE/TV, MUSIC, and GAME (b). The basic operations are introduced in the Basic Manual. For more details, see the Advanced Manual. 0 The listening mode last selected for the source is remembered for each of the MOVIE/TV, MUSIC, and GAME buttons. If content you play is not supported by the listening mode you selected last, the listening mode that is standard for that content is selected automatically. a b Dolby Digital/DTS Modes When the input signal is a digital surround format such as Dolby Digital or DTS, you can select the listening mode that suits the input signal. Dolby Digital is displayed for Dolby Digital and DTS-HD Master Audio is displayed for DTS-HD Master Audio. The output is Stereo for 2-channel input signals. Direct This listening mode can be selected for all input signals. It shuts down processing that affects sound quality to deliver a playback sound quality closer to sources. Speakers play the sound field according to the number of channels in the input signal, so there would be output from only the front speakers for a 2 ch signal, for example. Note that the sound quality cannot be adjusted if this mode is selected. Dolby Surround/DTS Neural:X These listening modes allow you to expand the playback signal to 5.1 channels or 7.1 channels to suit the connected speaker configuration when the input signal is 2 channels or 5.1 channels. THX surround modes Multiple surround speakers are installed in movie theaters so that the moviegoer is enveloped in a natural surround sound. Even with just two surround speakers, the THX Cinema mode achieves, with the high quality technology developed by THX, the same kind of breadth of sound you would get in a movie theater along with the natural flow of timbre with the sound field towards the front. Also available are modes such as THX Music, THX Games. Note that the sound quality cannot be adjusted if this mode is selected. Original Surround Modes You can select listening modes such as the All Ch Stereo mode where a stereo image is played from both the front and the rear, and Orchestra (only with the MUSIC button) which is best for playback of classical and opera pieces. Checking the Input Format and Listening Mode Press (a) on the remote controller several times to switch the display of the main unit as follows. Input source & volume Listening mode Signal format The display changes few seconds later. Sampling frequency Input signal resolution En 31 Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Surround, Dolby Vision and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see patents.dts.com. Manufactured under license from DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. THX and the THX logo are trademarks of THX Ltd., registered in the U.S. and other countries. THX CERTIFIED SELECT and the THX SELECT application icon are trademarks of THX Ltd. THX Select Before any home theater component can be THX Select certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Select logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come. THX Select requirements define hundreds of parameters, including power amplifier performance, and integrated amplifier performance and operation for both digital and analog domains. THX Select receivers also feature proprietary THX technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater playback. Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd. ® The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. The Wi-Fi CERTIFIED Logo is a certification mark of Wi-Fi Alliance®. AirPlay, iPad, iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. iPad Air and iPad mini are trademarks of Apple Inc. “Made for iPod”, “Made for iPhone” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone or iPad may affect wireless performance. AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain Lion or later, and PC with iTunes 10.2.2 or later. PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc. Used with permission. The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The Spotify software is subject to third party licenses found here: developer.spotify.com/esdk-third-party-licenses/ This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. Windows 7, Windows Media, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. DSD and the Direct Stream Digital logo are trademarks of Sony Corporation. "Theater-Dimensional" and "Theater-Dimensional (logo)" are trademarks of Onkyo Corporation. “All other trademarks are the property of their respective owners.” “Toutes les autres marques commerciales sont la propriété de leurs détenteurs respectifs.” “El resto de marcas comerciales son propiedad de sus respectivos propietarios”. 32 1-10-5 Yokoami, Sumida-ku, Tokyo 130-0015 JAPAN onkyo.com/ <U.S.A.> 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. For Dealer, Service, Order and all other Business Inquiries: Tel: 201-785-2600 Fax: 201-785-2650 us.onkyo.com/ For Product Support Team Only: 1-800-229-1687 us.onkyo.com/ <Germany> Gutenbergstrasse 3, 82178 Puchheim, Germany Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 eu.onkyo.com/ <UK> Anteros Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex, HA4 6QQ United Kingdom Tel: +44 (0)871-200-1996 Fax: +44 (0)871-200-1995 For Product Support only: +44 (0)208-836-3510 uk.onkyo.com/en/ <France> 6, Avenue de Marais F - 95816 Argenteuil Cedex FRANCE For Product Support only: +33 969 368 138 fr.onkyo.com/fr/ <Hong Kong> Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: +852-2429-3118 Fax: +852-2428-9039 hk.onkyo.com/ <PRC> 302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032, Tel: +86-21-52131366 Fax: +86-21-52130396 cn.onkyo.com/ <Asia, Oceania, Middle East, Africa> Please contact an Onkyo distributor referring to Onkyo SUPPORT site. intl.onkyo.com/support/ The above-mentioned information is subject to change without prior notice. Visit the Onkyo web site for the latest update. F1710-1 (C) Copyright 2017 Onkyo & Pioneer Corporation Japan. All rights reserved. onkyo.com/privacy/ Printed in Malaysia / Imprimé en Malaisie SN 29402781A *29402781A*

Adva

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual AV RECEIVER TX-NR777 Troubleshooting Supplementary Information, etc. | Advanced Manual Specifications General Specifications............................................................. 2 About HDMI ............................................................................. 4 Playback from USB storage devices ....................................... 5 Playback from the Music Server .............................................. 6 Advanced Setup Setup Menu ............................................................................. 7 Quick Menu ........................................................................... 26 Web Setup ............................................................................. 27 Control Function Settings ...................................................... 28 Firmware Update ................................................................... 29 Listening Modes Selecting Listening Modes..................................................... 32 Listening Mode Effects .......................................................... 33 Selectable Listening Modes................................................... 36 Network Functions Internet Radio ........................................................................ 48 Spotify.................................................................................... 49 AirPlay® ................................................................................. 50 Music Server.......................................................................... 51 Supplementary information for player functions .................... 53 Troubleshooting .................................................................. 54 Supplementary Information, etc......................................... 61 The Basic Manual includes information needed when starting up and also instructions for frequently used operations. The Advanced Manual has more detailed information and advanced settings. > Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

General Specifications ■ Amplifier Section Rated Output Power (FTC) (North American) With 8 ohm loads, both channels driven, from 20- 20,000 Hz; rated 110 watts per channel minimum RMS power, with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output. Surround Mode Output Power (*) (6 ohms, 1 kHz THD 0.9%) 180 W per channel * Reference output for each speakers. Depending on the source and the listening mode settings, there may be no sound output. Maximum Effective Output Power (JEITA) (North American) 7 ch × 220 W at 6 ohms, 1 kHz, 1 ch driven of 10% THD Dynamic Power (*) * IEC60268-Short-term maximum output power 250 W (3 Ω, Front) 220 W (4 Ω, Front) 130 W (8 Ω, Front) THD+N (Total Harmonic Distortion+Noise) 0.08% (20 Hz - 20,000 Hz, half power) Input Sensitivity and Impedance (1 kHz 100 W/8 Ω) 200 mV/47 kΩ (LINE (Unbalance)) 3.5 mV/47 kΩ (PHONO MM) Rated RCA Output Level and Impedance 1 V/470 Ω (SUBWOOFER PRE OUT) 200 mV/2.3 kΩ (ZONE LINE OUT) Phono Overload 70 mV (MM 1 kHz 0.5%) Frequency Response 10 Hz - 100 kHz/+1 dB, –3 dB (Direct) Tone Control Characteristics ±10 dB, 90 Hz (BASS) ±10 dB, 7.5 kHz (TREBLE) Signal to Noise Ratio 106 dB (IHF-A, LINE IN, SP OUT) 80 dB (IHF-A, PHONO IN, SP OUT) Speaker Impedance 4 Ω - 16 Ω Headphone Output Impedance 330 Ω Headphone Rated Output 85 mW (32 Ω, 1 kHz, 10% THD) ■ Video Section Signal level 1 Vp-p/75 Ω (Composite Video) 1 Vp-p/75 Ω (Component Video Y) 0.7 Vp-p/75 Ω (Component Video B/R) Maximum resolution supported by component video 480i/576i ■ Tuner Section FM Tuning Frequency Range 87.5 MHz - 107.9 MHz AM Tuning Frequency Range 530 kHz - 1710 kHz Preset Channel 40 ■ Network Section Ethernet LAN 10BASE-T/100BASE-TX Wireless LAN IEEE 802.11 a/b/g/n standard (Wi-FiR standard) 5 GHz/2.4 GHz band ■ BLUETOOTH Section Communication system BLUETOOTH Specification version 4.1+LE Frequency band 2.4 GHz band Troubleshooting Supplementary Information, etc. | Modulation method FHSS (Freq Hopping Spread Spectrum) Compatible BLUETOOTH profiles A2DP 1.2 AVRCP 1.3 HOGP-Host (Client) HOGP-HID Device (Server) HID Service (HIDS) Supported Codecs SBC AAC Transmission range (A2DP) 20 Hz - 20 kHz (Sampling frequency 44.1 kHz) Maximum communication range Line of sight approx. 15 m (*) ⯋ The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone, reception sensitivity, antenna's performance, operating system, software application, etc. ■ General Power Supply AC 120 V, 60 Hz Power Consumption 600 W 0.15 W (Stand-by) 65 W (No-sound) 5.7 W (HDMI Standby Through) 2.6 W (Network Standby) Dimensions (W × H × D) 435 mm × 173.5 mm × 378 mm 17-1/8" × 6-13/16" × 14-7/8" Weight 10.5 kg (23.1 lbs.) ■ HDMI Input IN1 (BD/DVD), IN2 (CBL/SAT), IN3 (STRM BOX), IN4 (GAME), IN5 (PC), IN6, AUX INPUT HDMI

2

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

(front) Output OUT MAIN (ARC), OUT SUB Supported Deep Color, x.v.Color™, LipSync, Audio Return Channel, 3D, 4K 60 Hz, CEC, Extended Colorimetry (sYCC601, Adobe RGB, Adobe YCC601), Content Type, HDR Audio Format Dolby Atmos, Dolby TrueHD, Dolby Digital, Dolby Digital Plus, DTS, DTS:X, DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS 96/24, DTS ES, DTS-HD Express, DSD, PCM Maximum Video Resolution 4k 60 Hz (YCbCr 4:4:4) ■ Video Inputs Component IN1 (BD/DVD), IN2 (GAME) Composite IN1 (CBL/SAT), IN2 (STRM BOX) ■ Compatible input resolutions HDMI input 4K, 1080p/24, 1080p, 1080i, 720p, 480p/576p Component input 480i/576i Composite input 480i/576i • The output from the HDMI OUT jack to the TV is the same resolution as the input. ■ Audio Inputs Digital OPTICAL 1 (CD), 2 (TV) COAXIAL (BD/DVD) Analog BD/DVD, CBL/SAT, GAME, STRM BOX, CD, TV, PHONO, AUX (front) ■ Audio Outputs Analog ZONE2 LINE OUT 2 SUBWOOFER PRE OUT Speaker Outputs FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK or HEIGHT (ZONE 2B) L/R, ZONE 2A L/R (Banana plug ready) Phones PHONES (Front, ø 6.3 mm, 1/4") ■ Others Setup Mic : 1 (Front) USB : 1 (Ver. 2.0, 5 V/1 A) Ethernet : 1 RS232 : 1 IR IN : 1 12V TRIGGER OUT : 1 (MAIN, 100 mA) ■ Power consumption in standby mode • In the following cases, the power consumption in standby mode may reach up to a maximum of 12 W: – When "Network Standby" is set to "On" – When "HDMI CEC" is set to "On" – When "HDMI Standby Through" is set to other than "Off" – When "Bluetooth Wakeup" is set to "On" – When "USB Power Out at Standby" is set to "On" Specifications and features are subject to change without notice. Troubleshooting Supplementary Information, etc. |

3

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

About HDMI ■ Compatible functions HDMI (High Definition Multimedia Interface) is a digital interface standard for connecting TVs, projectors, Blu ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video and digital audio (2 ch PCM, multichannel digital audio, and multichannel PCM). HDMI CEC functionality: By connecting devices and HDMI cables that comply with the CEC (Consumer Electronics Control) specification of the HDMI standard, a variety of linked operation become possible between devices. You can enjoy features such as linking input switching with the input selector and players, control volume using the remote controller of the TV, and automatically switching this unit to standby when the TV is turned off. The unit is designed to link with products that comply with the CEC standard, and that linked operation is not always guaranteed with all CEC devices. For linked functions to work properly, do not connect more CEC-compliant components than the quantities specified below, to the HDMI jack. • Blu-ray Disc/DVD players: up to 3 units. • Blu-ray Disc/DVD recorders: up to 3 units. • Cable TV tuner, terrestrial digital tuner, and satellite broadcasting tuner: up to 4 units. Operation has been confirmed on the following devices: (As of February 2017) Toshiba brand televisions; Sharp brand televisions; Onkyo and Integra brand RIHD-compatible players; Toshiba brand players and recorders; Sharp brand players and recorders (when used with a Sharp brand television) ARC(Audio Return Channel): By connection a TV that supports ARC with a single HDMI cable, you can not only output the audio and video from this unit to the TV, but also input the audio from the TV to this unit. HDMI Standby Through: Even if this unit is in standby, the input signals from AV components are transmitted to the TV. Deep Color: By connecting devices supporting Deep Color, video signals input from the devices can be reproduced on the TV with even more colors. x.v.Color™: This technology realizes even more realistic colors by broadening the color gamut. 3D: You can transmit 3D video signals from AV components to the TV. 4K: This unit supports 4K (3840×2160p) and 4K SMPTE (4096×2160p) video signals. LipSync: This setting automatically corrects any desynchronization between the video and audio signals based on data from the HDMI LipSync compatible TV. Copyright Protection: The unit supports Revision 1.4 and Revision 2.2 of the HDCP (High-bandwidth Digital Content Protection), a copy protection system for digital video signals. Other devices connected to the unit must also support HDCP. ■ Supported Audio Formats 2 ch linear PCM: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit Multi-channel linear PCM: Troubleshooting Supplementary Information, etc. | Maximum 7.1 channels, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit Bitstream: Dolby Atmos, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS:X, DTS-HD High Resolution Audio, DTS-HD Master Audio DSD: Supported sampling rates: 2.8 MHz Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats. ■ Supported resolutions HDMI IN1 to IN6: • Copyright protection technology: HDCP1.4/HDCP2.2 • Color space (Color Depth): – 720×480i 60Hz, 720×576i 50Hz, 720×480p 60Hz, 720×576p 50Hz, 1920×1080i 50/60Hz, 1280×720p 24/25/30/50/60Hz, 1680×720p 24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz, 2560×1080p 24/25/30/50/60Hz, 4K (3840×2160p) 24/25/30Hz, 4K SMPTE (4096×2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8/10/12 bit), YCbCr4:2:2 (12 bit) – 4K (3840×2160p) 50/60Hz, 4K SMPTE (4096 ×2160p) 50/60Hz : RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit), YCbCr4:2:0 (8/10/12 bit) AUX INPUT HDMI (front): • Copyright protection technology: HDCP1.4/HDCP2.2 • Color space (Color Depth): – 720×480i 60Hz, 720×576i 50Hz, 720×480p 60Hz, 720×576p 50Hz, 1920×1080i 50/60Hz, 1280×720p 24/25/30/50/60Hz, 1680×720p 24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz, 2560×1080p 24/25/30/50/60Hz : RGB/YCbCr4:4:4 (8/10/12 bit), YCbCr4:2:2 (12 bit) – 4K (3840×2160p) 24/25/30Hz, 4K SMPTE (4096 ×2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit) – 4K (3840×2160p) 50/60Hz, 4K SMPTE (4096× 2160p) 50/60Hz : YCbCr4:2:0 (8 bit)

4

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Playback from USB storage devices ■ USB Storage Device Requirements • This unit can use USB storage devices that comply with the USB mass storage device class standard. • FAT16 or FAT32 file system format. • If the USB storage device has been partitioned, each section will be treated as an independent device. • Up to 20,000 tracks per folder can be displayed, and folders may be nested up to 16 levels deep. • USB hubs and USB storage devices with hub functions are not supported. Do not connect these devices to the unit. • USB storage devices with security function are not supported on this unit. • If you connect a USB hard disk drive to the USB port of the unit, we recommend that you use its AC adapter to power it. • Media inserted to the USB card reader may not be available in this function. Furthermore, depending on the USB storage device, proper reading of the contents may not be possible. • Our company accepts no responsibility whatsoever for the loss or damage to data stored on a USB storage device when that device is used with this unit. We recommend that you back up your important music files beforehand. ■ Supported Audio Formats This unit supports the following music file formats. Note that sound files that are protected by copyright cannot be played on this unit. MP3 (.mp3/.MP3): • Supported formats: MPEG-1/MPEG-2 Audio Layer 3 • Supported sampling rates: 44.1 kHz, 48 kHz • Supported bitrates: Between 8 kbps and 320 kbps. WMA (.wma/.WMA): • Supported sampling rates: 44.1 kHz, 48 kHz • Supported bitrates: Between 5 kbps and 320 kbps. • WMA Pro/Voice/WMA Lossless formats are not supported WAV (.wav/.WAV): WAV files include uncompressed PCM digital audio. • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit AIFF (.aiff/.aif/.AIFF/.AIF): AIFF files include uncompressed PCM digital audio. • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/ .MP4/.3GP/.3G2): • Supported formats: MPEG-2/MPEG-4 Audio • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz • Supported bitrates: Between 8 kbps and 320 kbps. FLAC (.flac/.FLAC): • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit Apple Lossless (.m4a/.mp4/.M4A/.MP4): • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 16 bit, 24 bit DSD (.dsf/.dff/.DSF/.DFF): • Supported formats: DSF/DSDIFF • Supported sampling rates: 2.8 MHz, 5.6 MHz Dolby TrueHD (.vr/.mlp/.VR/.MLP): • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Variable bit-rate (VBR) files are supported. However, Troubleshooting Supplementary Information, etc. | playback times may not be displayed correctly. • This unit supports the gapless playback of the USB storage device in the following conditions. When playing WAV, FLAC and Apple Lossless, and the same format, sampling frequency, channels and quantization bit rate are played continuously.

5

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Playback from the Music Server ■ Supported Audio Formats This unit supports the following music file formats. Remote play of FLAC and DSD is not supported. MP3 (.mp3/.MP3): • Supported formats: MPEG-1/MPEG-2 Audio Layer 3 • Supported sampling rates: 44.1 kHz, 48 kHz • Supported bitrates: Between 8 kbps and 320 kbps. WMA (.wma/.WMA): • Supported sampling rates: 44.1 kHz, 48 kHz • Supported bitrates: Between 5 kbps and 320 kbps. • WMA Pro/Voice/WMA Lossless formats are not supported WAV (.wav/.WAV): WAV files include uncompressed PCM digital audio. • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit AIFF (.aiff/.aif/.AIFF/.AIF): AIFF files include uncompressed PCM digital audio. • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/ .MP4/.3GP/.3G2): • Supported formats: MPEG-2/MPEG-4 Audio • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz • Supported bitrates: Between 8 kbps and 320 kbps. FLAC (.flac/.FLAC): • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit LPCM (Linear PCM): • Supported sampling rates: 44.1 kHz, 48 kHz • Quantization bit: 16 bit Apple Lossless (.m4a/.mp4/.M4A/.MP4): • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz • Quantization bit: 16 bit, 24 bit DSD (.dsf/.dff/.DSF/.DFF): • Supported formats: DSF/DSDIFF • Supported sampling rates: 2.8 MHz, 5.6 MHz • Variable bit-rate (VBR) files are supported. However, playback times may not be displayed correctly. • Remote playback does not support the gapless playback. Troubleshooting Supplementary Information, etc. |

6

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Troubleshooting Supplementary Information, etc. | 1. Input/Output Assign

Setup Menu The unit allows you to configure advanced settings to provide you with an even better experience. Operation: Use the on-screen displays (OSD) that appear on the TV to make the settings. Press on the remote controller to display the Setup menu. Setup Make settings related to output to the TV, change the settings for jack allocations to the various input selectors, and set the feature for displaying operations on the TV (OSD), etc. ■ 1. TV Out / OSD Setting Item Default Value Setting Details HDMI Out MAIN Select the HDMI jack to be connected with the TV. "MAIN": When connecting the TV to the HDMI OUT MAIN jack "SUB": When connecting the TV to the HDMI OUT SUB jack "MAIN+SUB": When connecting to both the MAIN

1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Hardware 6. Multi Zone 7. Miscellaneous 1. TV Out / OSD 2. HDMI Input 3. Video Input 4. Digital Audio Input 5. Analog Audio Input and SUB jacks Dolby Vision MAIN If you want to output the Dolby Vision video from the player to a TV that supports Dolby Vision, select the HDMI OUT jack, MAIN or SUB, to which you have connected the TV that supports Dolby Vision. This setting is only necessary if you have set "HDMI Out" to "MAIN+SUB" and you have

Select the item with the cursor / buttons of the remote controller and press ENTER to confirm your selection. Use the cursors / to change the default values. • To return to the previous screen, press . • To exit the settings, press . connected a TV to both the MAIN and SUB jacks. "MAIN": To output Dolby Vision video to a TV that supports Dolby Vision that is connected to the HDMI OUT MAIN jack "SUB": To output Dolby Vision video to a TV that supports Dolby Vision that is connected to the HDMI OUT SUB jack • If you select "MAIN" or "SUB" but the video on the TV does not appear correctly, set this to "Off". OSD Language English Select the on-screen display language from the following. English, German, French, Spanish, Italian, Dutch, Swedish

7

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting Item Default Value Setting Details Troubleshooting Supplementary Information, etc. | ■ 2. HDMI Input Impose OSD On Set whether or not to display the information on the TV when the volume is adjusted or input is changed, for example. You can change input assignment between the input selectors and HDMI IN jacks. Setting Item Default Value Setting Details

"On": OSD displayed on the TV. "Off": OSD not displayed on the TV. • OSD may not be displayed depending on the input signal even if "On" is selected. If the operation screen is not displayed, change the resolution of the connected device. Mini Player OSD Always On You can play on the TV the images from another input selected immediately prior while you are playing the audio from NET or BLUETOOTH input. After switching to NET or BLUETOOTH, play the images and audio, then when you press MODE on the remote controller, the image is displayed in full-screen mode, and the audio information (Mini Player) for NET or BLUETOOTH is displayed in the corner of the screen. You can set whether to display this Mini Player on the screen all the time. "Always On": The Mini Player is displayed all the time. "Auto Off": The Mini Player turns off automatically 30 seconds after being displayed. It is displayed for 30 seconds after operations such as changing the volume. • Each press of the MODE button displays or turns off the video. • This cannot be selected if "Impose OSD" is set to "Off". Screen Saver 3 minutes Set the time to start the screen saver. Select a value from "3 minutes", "5 minutes", "10 minutes" and "Off". BD/DVD HDMI 1 (HDCP 2.2) CBL/SAT HDMI 2 (HDCP 2.2) GAME HDMI 4 (HDCP 2.2) STRM BOX HDMI 3 (HDCP 2.2) PC HDMI 5 (HDCP 2.2) "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the BD/DVD button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the CBL/SAT button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the GAME button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the STRM BOX button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the PC button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first.

CD --- "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the CD button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. 8

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting Item Default Value Setting Details TV --- "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the TV button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. PHONO --- "HDMI 1 (HDCP 2.2)" to "HDMI 6 (HDCP 2.2)": Assign a desired HDMI IN jack to the PHONO button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. ■ 3. Video Input You can change input assignment between the input selectors and COMPONENT VIDEO IN jacks and the VIDEO IN jacks. If you do not assign a jack, select "---". Setting Item Default Value Setting Details BD/DVD COMPONENT 1 "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the BD/DVD button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the BD/DVD button. CBL/SAT VIDEO 1 "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the CBL/SAT button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the CBL/SAT button. GAME COMPONENT 2 "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the GAME button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the GAME button. STRM BOX VIDEO 2 "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the STRM BOX button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the STRM BOX button. Troubleshooting Supplementary Information, etc. | Setting Item Default Value Setting Details PC --- "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the PC button. "VIDEO 1" to "VIDEO 2": Assign a desired VIDEO IN jack to the PC button. CD --- "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the CD button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the CD button. TV --- "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the TV button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the TV button. PHONO --- "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the PHONO button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the PHONO button. ■ 4. Digital Audio Input You can change input assignment between the input selectors and DIGITAL IN COAXIAL/ OPTICAL jacks. If you do not assign a jack, select "---". Setting Item Default Value Setting Details BD/DVD COAXIAL "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the BD/DVD button. CBL/SAT --- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the CBL/SAT button. GAME --- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the GAME button. STRM BOX --- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the STRM BOX button. PC --- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the PC button. CD OPTICAL 1 "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the CD button.

9

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Setting Item Default Value Setting Details ■ 5. Analog Audio Input Troubleshooting Supplementary Information, etc. |

TV OPTICAL 2 "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the TV button. PHONO --- "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired DIGITAL IN jack to the PHONO button. • Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz/16bit, 20bit, and 24bit. You can change input assignment between the input selectors and AUDIO IN jacks. If you do not assign a jack, select "---". Setting Item Default Value Setting Details BD/DVD AUDIO 1 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the BD/DVD button. CBL/SAT AUDIO 2 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the CBL/SAT button. GAME AUDIO 3 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the GAME button. STRM BOX AUDIO 4 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the STRM BOX button. PC --- "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the PC button. CD AUDIO 5 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the CD button. TV AUDIO 6 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the TV button. PHONO PHONO The setting cannot be changed.

10

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual 2. Speaker You can make changes to the connection environment of the speakers and change the volume level. Settings are automatically configured if you use AccuEQ Room Calibration. This setting cannot be selected if headphones are connected or audio is output from the speakers of the TV. ■ 1. Configuration Setting Item Default Value Setting Details Troubleshooting Supplementary Information, etc. | Setting Item Default Value Setting Details Bi-Amp No Set whether the front speakers are bi-amp connected. "No": When front speakers are not bi-amp connected "Yes": When front speakers are bi-amp connected • This item will be fixed to "No" when anything other than "No" is selected for the "Zone Speaker". • This setting cannot be selected when surround

Speaker Channels 7.1 ch Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1 ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2 ch", or "5.1.2 ch" to suit the number of speaker channels connected. Speaker Impedance back speakers or height speakers are installed. 6ohms Set the impedance (Ω) of the connected speakers. "4ohms": When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance

Subwoofer Yes Set whether a subwoofer is connected or not. "Yes": When subwoofer is connected "No": When subwoofer is not connected Height Speaker Top Middle Set the speaker type if height speakers are connected to the SURROUND BACK or HEIGHT terminals. Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High", "Dolby Speaker (Front)", or "Dolby Speaker (Surr)" according to the type and layout of the connected speakers. • If an item cannot be selected even though connection is correct, check that the settings in "Speaker Channels" matches the number of connected channels. Zone Speaker No Set the connection of speakers to Zone 2 speaker terminals. "Zone 2": When speakers are connected to Zone 2A speaker terminals "Zone 2A+B": When speakers are connected to Zone 2A and Zone 2B speaker terminals • This setting cannot be selected when surround back speakers or height speakers are installed. "No": When speakers are not connected to Zone 2 speaker terminals "6ohms": When the connected speakers all have 6 Ω or more impedance. • For impedance, check the indications on the back of the speakers or their instruction manual.

11

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual ■ 2. Crossover • If you are using THX-certified speakers, we recommend the following settings: – Set a value "80Hz(THX)" in Crossover frequency. – Set a value "80Hz" in "LPF of LFE". – Set a value "Off" in "Double Bass". Setting Item Default Value Setting Details Front 80Hz(THX) Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • If "Configuration" - "Subwoofer" is set to "No", "Front" will be fixed to "Full Band" and the low pitched range of the other channels will be output from the front speakers. Refer to the instruction manual of your speakers to make the setting. Center 80Hz(THX) Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels. Height 80Hz(THX) Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels. Troubleshooting Supplementary Information, etc. | Setting Item Default Value Setting Details Surround 80Hz(THX) Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels. Surround Back 80Hz(THX) Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Surround" is set to "Full Band". • If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels. LPF of LFE 120Hz Set the low-pass filter for LFE (low-frequency effect) signals in order to pass lower frequency signals than the set value and thus cancel unwanted noises. The low-pass filter will be effective only on sources with LFE channel. The value from "80Hz" to "120Hz" can be set. "Off": When this function is not to be used Double Bass On This can be selected only when "Configuration" - "Subwoofer" is set to "Yes" and "Front" is set to "Full Band". Boost bass output by feeding bass sounds from the front left and right, and center speakers to the subwoofer. "On": Bass output will be boosted "Off": Bass output will not be boosted • The setting will not automatically be configured even if you performed AccuEQ Room Calibration.

12

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual ■ 3. Distance Set the distance from each speaker to the listening position. Setting Item Default Value Setting Details Front Left 12.0ft/3.60m Specify the distance between each speaker and the listening position. Center 12.0ft/3.60m Specify the distance between each speaker and the listening position. Front Right 12.0ft/3.60m Specify the distance between each speaker and the listening position. Height Left 9.0ft/2.70m Specify the distance between each speaker and the listening position. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Height Right 9.0ft/2.70m Specify the distance between each speaker and the listening position. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Surround Right 7.0ft/2.10m Specify the distance between each speaker and the listening position. Surr Back Right 7.0ft/2.10m Specify the distance between each speaker and the listening position. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Surr Back Left 7.0ft/2.10m Specify the distance between each speaker and the listening position. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Surround Left 7.0ft/2.10m Specify the distance between each speaker and the listening position. Subwoofer 12.0ft/3.60m Specify the distance between each speaker and the listening position. • Distance units can be switched by pressing MODE on the remote controller. When the unit is set as Troubleshooting Supplementary Information, etc. | feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1ft. When the unit is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.

13

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual ■ 4. Level Calibration Setting Item Default Value Setting Details Front Left 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. Center 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. Front Right 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. Height Left 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Height Right 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Troubleshooting Supplementary Information, etc. | Setting Item Default Value Setting Details Surr Back Right 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Surr Back Left 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Surround Left 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. Subwoofer 0.0 dB Select a value between "-15.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. ■ 5. Dolby Enabled Speaker Setting Item Default Value Setting Details

Speaker" and Zone 2 is on. Surround Right 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. Dolby Enabled Speaker to Ceiling 6.0 ft/1.80 m Set the distance between the Dolby Enabled Speaker and the ceiling. Select between "0.1 ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units). • The unit of distance (ft/m) shown is the unit selected for use in "Distance".

AccuReflex Off You can enhance the reflection effect of Dolby Enabled Speakers from the ceiling. "Off": When this function is not to be used "On": When this function is to be used • This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker". 14

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual ■ 6. Equalizer Settings You can adjust the output volume of the range of each connected speaker. You can adjust the volume of the different sound ranges for each of the speakers. You can set three different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and nine bands for all other speakers. Troubleshooting Supplementary Information, etc. | • The result may not be as expected depending on the input source and listening mode setting. ■ 7. THX Audio Setting item Default Value Setting Details

Setting Item Default Value Setting Details Front 0.0 dB After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / . Center 0.0 dB After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / . Height 0.0 dB After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / . • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Surround 0.0 dB After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors Back Speaker Spacing THX Ultra / Select Subwoofer >4.0 ft/>1.2 m Select the distance between the surround back speakers from "<1.0 ft/<0.3 m", "1.0 - 4.0 ft/0.3 - 1.2 m", and ">4.0 ft/>1.2 m". • The unit of distance (ft/m) shown is the unit selected for use in "Distance". • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. • If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels. No Set "Yes" or "No" of the connection of the THX certified subwoofer. "Yes": When a THX-certified subwoofer is connected "No": When a THX-certified subwoofer is not connected • The setting cannot be changed if "Configuration" - "Subwoofer" is set to "No".

/ , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / . Surround Back 0.0 dB After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / . • The setting cannot be changed if anything other than "No" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Subwoofer 0.0 dB After selecting the speaker frequency from between "25 Hz" and "160 Hz" with the cursors / , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / . • This cannot be selected if "No" is set in "Configuration" - "Subwoofer". BGC Off If your listening room layout (for practical or aesthetic reasons) locates most of the listeners close to the rear wall, the resulting bass level can be sufficiently reinforced by the boundary that the overall sound becomes "boomy". THX Select receivers contain a Boundary Gain Compensation (BGC) feature to improve bass balance. "On": When this function is to be used "Off": When this function is not to be used • In the following cases, the setting cannot be changed: – "Configuration" - "Subwoofer" is set to "No". – "THX Ultra / Select Subwoofer" is set to "No".

15

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting item Default Value Setting Details Troubleshooting Supplementary Information, etc. | 3. Audio Adjust Loudness Plus On When the setting is set to "On", it is possible to enjoy even subtle nuances of audio expression at low volume. This is only available when the THX listening mode is selected. THX Loudness Plus THX Loudness Plus is a new volume control technology featured in THX Ultra and THX Make advanced settings such as those related to multiplex audio, settings for the LFE level, or those related to the volume of this unit. ■ 1. Multiplex/Mono Setting Item Default Value Setting Details

Select Certified receivers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that certain sound elements can be lost or perceived differently by the listener. THX Loudness Plus compensates for the tonal and spatial shifts that occur when the volume is reduced by intelligently adjusting ambient surround channel levels and frequency response. This enables users experience the true impact of soundtracks regardless of the volume setting. THX Loudness Plus is automatically applied when listening in any THX listening mode. The new THX Cinema, THX Music, and THX Games modes are tailored to apply the proper THX Loudness Plus settings for each type of content. Multiplex Input Channel Mono Input Channel Mono Output Speaker Main Set the audio channel or language to be output when playing multiplex audio or multilingual TV broadcasts etc. "Main": Main channel only "Sub": Sub channel only "Main/Sub": Main and sub channels will be output at the same time. • If multiplex audio is being played, "1+1" will be displayed when on the remote controller is pressed. Left + Right Set the input channel to use for playing any 2 ch digital source such as Dolby Digital, or 2 ch analog/ PCM source in the Mono listening mode. "Left": Left channel only "Right": Right channel only "Left + Right" : Left and right channels Center Select the speaker to output monaural audio in the Mono listening mode. "Center": Audio is output from the center speaker. "Left/Right": Audio is output from the front L/R speakers. • If an item cannot be selected even though connection is correct, check that the settings in "2. Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.

16

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

■ 2. Dolby ■ 5. Volume Troubleshooting Supplementary Information, etc. |

Setting Item Default Value Setting Details Setting Item Default Value Setting Details

Loudness Management ■ 3. DTS On When playing Dolby TrueHD, enable the dialog normalization function which keeps the volume of dialog at a certain level. Note that when this setting is Off, the Late Night function that allows you to enjoy surround at low volumes is fixed to off when playing Dolby Digital Plus/Dolby TrueHD. "On": When this function is to be used "Off": When this function is not to be used Volume Display Absolute Switch the volume display between the absolute value and relative value. The absolute value 82.0 is equivalent to the relative value 0.0dB. "Absolute": Absolute value such as "0.5" and "99.5" "Relative": Relative value such as "-81.5dB" and "+18.0dB" • If the absolute value is set to 82.0, "82.0Ref" will appear on the display. Mute Level -㱣dB Set the volume lowered from the listening volume when muting is on. Select a value from "-㱣dB", "-40dB", and "-20dB".

Setting Item Default Value Setting Details Maximum Volume Off Set the maximum value to avoid too high volume. Select a value from "Off", "50" to "99". (When

DTS Auto Surround ■ 4. LFE Level On When inputting DTS signals that include extended channel information, the optimum listening mode is automatically selected according to the extended information contained in the input signal and the speaker configuration of this unit when playing in the straight decoding listening mode. "On": Use this function "Off": Audio is played using the same amount of channels in the input signal according to the speaker configuration of this unit. • The ES Matrix and ES Discrete listening modes cannot be selected if this function is set to "Off". "Volume Display" is set to "Absolute") Power On Volume Last Set the volume level of when the power is turned on. Select a value from "Last" (Volume level before entering standby mode), "Min", "0.5" to "99.5" and "Max". (When "Volume Display" is set to "Absolute") • You cannot set a higher value than that of "Maximum Volume". Headphone Level 0.0 dB Adjust the output level of the headphones. Select a value between "-12.0 dB" and "+12.0 dB".

Set the low-frequency effect (LFE) level for Dolby Digital series, DTS series, Multichannel PCM, and DSD signals. Setting Item Default Value Setting Details LFE Level 0dB Select the low-frequency effect (LFE) level of each type of signal from "0dB" to "-㱣dB". If the low frequency effect sound is too strong, select "-20dB" or "-㱣dB". 17

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual 4. Source Make settings for input sources, such as volume difference adjustments for each input selector for the connected equipment. ■ 1. IntelliVolume Adjust the volume level difference between the devices connected to the unit. Select the input selector to configure. Setting Item Default Value Setting Details Troubleshooting Supplementary Information, etc. | • To name a preset radio station, press TUNER on the remote controller, select AM/FM and select the preset number. • This cannot be set if the "NET" or "BLUETOOTH" input is selected. ■ Audio Select Select the priority for input selection when multiple audio sources are connected to one input selector, such as connections to both the "BD/DVD" HDMI IN jack and the "BD/DVD" AUDIO IN jack. The setting can be separately set to each input selector button. Select the input selector to configure. Note that there are some default values you cannot change. Setting Item Default Value Setting Details

IntelliVolume 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB". Set a negative value if the volume of the target device is larger than the others and a positive value if smaller. To check the audio, start playback of the connected device. • This function is not effective in Zone 2. ■ 2. Name Edit Set an easy name to each input. The set name will be shown on the main unit display. Select the input selector to configure. Setting Item Default Value Setting Details Name Edit Input name 1. Select a character or symbol with the cursors and press ENTER. Repeat it to input 10 or less characters. "A/a": Switches between upper and lower cases. (Pressing MODE on the remote controller also toggles between upper and lower cases) "←" "→": Moves the cursor to the arrow direction. " ": Removes a character on the left of the cursor. " ": Enters a space. • Pressing CLEAR on the remote controller will remove all the input characters. 2. After inputting, select "OK" with the cursors and press ENTER. The input name will be saved. Audio Select BD/DVD: HDMI CBL/SAT: HDMI GAME: HDMI STRM BOX: HDMI PC: HDMI AUX: HDMI CD: OPTICAL PHONO: Analog TV: OPTICAL "ARC": When giving priority to input signal from ARC compatible TV. • The setting can be selected only when "5. Hardware" - "HDMI" - "Audio Return Channel" is set to "Auto" and also the "TV" input is selected. "HDMI": When giving priority to input signal from HDMI IN jacks • The setting can be selected only when the input is assigned to the HDMI jack in the "1. Input/ Output Assign" - "HDMI Input" setting. "COAXIAL": When giving priority to input signal from DIGITAL IN COAXIAL jacks • The setting can be selected only when the input is assigned to the COAXIAL jack in the "1. Input/ Output Assign" - "Digital Audio Input" setting. "OPTICAL": When giving priority to input signal from DIGITAL IN OPTICAL jacks • The setting can be selected only when the input is assigned to the OPTICAL jack in the "1. Input/ Output Assign" - "Digital Audio Input" setting. "Analog": To always output analog audio independently of the input signal • The setting can be selected only when the input is assigned to the AUDIO IN jack in the "1. Input/Output Assign" - "Analog Audio Input" setting.

18

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting Item Default Value Setting Details Troubleshooting Supplementary Information, etc. | 5. Hardware PCM Fixed Mode Off Select whether to fix input signals to PCM (except multi-channel PCM) when you have selected "HDMI", "COAXIAL", or "OPTICAL" in the "Audio Select" setting. Set this item to "On" if noise is produced or truncation occurs at the beginning of a track when playing PCM sources. Select "Off" normally. • Changing "Audio Select" changes the setting to "Off". • The setting cannot be changed when "TUNER", "NET", or "BLUETOOTH" input is selected. ■ Video Select When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the input from which video is displayed on the TV. Setting Item Default Value Setting Details Video Select Last "Last": Select the video input played immediately prior. "BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "PC", "AUX", "CD", "TV", "PHONO": Play the video from the selected input. • This setting is effective for an input selector which is assigned in "1. Input/Output Assign" - "HDMI Input" and "Video Input". Make settings related to the HDMI CEC, HDMI Standby Through, ARC features, settings related to network features, and settings related to power management of the unit, such as Auto Standby and Network Standby, and 12V Trigger jack output settings. ■ 1. HDMI Setting Item Default Value Setting Details HDMI CEC Off Setting to "On" enables the input selection link and other link functions with HDMI connected CEC compliant device. "On": When this function is to be used "Off": When this function is not to be used When changing this setting, turn off and then on again the power of all connected components. • Depending on the TV set, a link may need to be configured on the TV. • This function is effective only when the device is connected to the HDMI OUT MAIN terminal. • Setting to "On" and closing the on-screen menu displays the name of the CEC-compatible components and "CEC On" on the display. • Power consumption in standby mode may increase if "On" is set. (Depending on the TV status, the unit will enter the normal standby mode.) • If you operate the MASTER VOLUME dial on the main unit when this setting is "On" and audio is output from the TV speakers, audio will be output also from the speakers connected to the unit. If you want to output from only either of them, change the unit or TV settings, or reduce the volume of the unit. • If abnormal operation occurs when you set the setting to "On", set it to "Off". • When connecting a non-CEC compatible component, or when you are not sure whether it is compatible, set the setting to "Off".

19

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting Item Default Value Setting Details Troubleshooting Supplementary Information, etc. | Setting Item Default Value Setting Details

HDMI Standby Through Off When this is set to anything other than "Off", you can play the video and audio of an HDMI connected player on the TV even if the unit is in standby mode. Only "Auto" and "Auto(Eco)" can be selected if "HDMI CEC" is set to "On". If you select anything else, set "HDMI CEC" to "Off". • Power consumption in standby mode increases if set to anything other than "Off". "BD/DVD", "CBL/SAT", "GAME", "STRM BOX", "PC", "AUX", "CD", "TV", "PHONO": For example, if you select "BD/DVD", you can play the equipment connected to the "BD/DVD" jack on the TV even if the unit is in standby mode. Select this setting if you have decided which player to use with this function. "Last": You can play the video and audio of the input selected immediately prior to the unit being switched to standby on the TV. When "Last" is selected, you can switch the input of the unit even in the standby mode with the remote controller or the Onkyo Remote app. "Auto", "Auto (Eco)": Select one of these settings when you have connected equipment that conforms to the CEC standard. You can play the Audio TV Out Off You can enjoy audio through the speakers of the TV while this unit is on. "On": When this function is to be used "Off": When this function is not to be used • This setting is fixed to "Auto" if you have set "1. Input/Output Assign" - "TV Out/OSD" - "HDMI Out" or "Other" - "HDMI Out" in the "Quick Menu" to "MAIN" or "MAIN+SUB" and "HDMI CEC" is set to "On". If you change this setting, set "HDMI CEC" to "Off". • Listening mode cannot be changed while "Audio TV Out" is set to "On" and audio is being output through the speakers of the TV. • Depending on your TV set or input signal of the component, audio may not output through the speakers of the TV even if this setting is set to "On". In such case, audio is output from the speakers of the unit. • If you operate the MASTER VOLUME dial on this unit when audio that is being input through this unit for output from the TV speakers, audio is output from this unit. If you do not want to output audio from the unit, change the unit or TV settings, or reduce the volume of the unit.

video and audio of the input selected on the TV, irrespective of what input was selected immediately prior to the unit being switched to standby, using the CEC link function. • To play players on the TV that do not conform to the CEC standard, you will need to turn the unit on and switch to the relevant input. • When using TV that complies with the Audio Return Channel Auto (*) You can enjoy sound of the HDMI connected ARC compatible TV through the speakers connected to the unit. * To use this function, set "HDMI CEC" to "On" in advance. "Auto": When enjoying the TV sound through the speakers connected to the unit "Off": When not using the ARC function

CEC standard, you can reduce the power consumption in standby mode by selecting "Auto (Eco)". Auto LipSync On This setting automatically corrects any desynchronization between the video and audio signals based on data from the HDMI LipSync compatible TV. "On": Automatic correction will be enabled "Off": Automatic correction will be disabled

20

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual ■ 2. Network Troubleshooting Supplementary Information, etc. | Setting Item Default Value Setting Details

• When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting automatically. ("Enable" is set by default) To assign fixed IP addresses to each components, you must set "DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set information related to your LAN, such as Subnet Mask and Gateway. Setting Item Default Value Setting Details Wi-Fi Off(Wired) Connect the unit to network via wireless LAN router. "On": Wireless LAN connection "Off(Wired)": Wired LAN connection Wi-Fi Setup - You can configure wireless LAN settings by pressing ENTER when "Start" is displayed. Wi-Fi Status - The information of the connected access point will be displayed. "SSID": SSID of the connected access point. "Signal": Signal strength of the connected access point. "Status": Status of the connected access point. MAC Address - This is the MAC address of this unit. This value is specific to the component and cannot be changed. DHCP Enable "Enable": Auto configuration by DHCP "Disable": Manual configuration without DHCP • If selecting "Disable", you must set "IP Address", "Subnet Mask", "Gateway", and "DNS Server" manually. IP Address 0.0.0.0 Displays/Sets the IP address. Subnet Mask 0.0.0.0 Displays/Sets the subnet mask. Gateway 0.0.0.0 Displays/Sets the gateway. DNS Server 0.0.0.0 Displays/Sets the primary DNS server. Proxy URL - Displays/Sets the proxy server URL. Proxy Port 8080 Displays/Sets the proxy server port number when you enter "Proxy URL". Friendly Name Onkyo TX-NR777 XXXXXX Change the device name for this unit which is shown on other devices connected to the network to an easily recognized name. 1. Press ENTER to display the Edit screen. 2. Select a character or symbol with the cursors and press ENTER. Repeat it to input 31 or less characters. "A/a": Switches between upper and lower cases. (Pressing MODE on the remote controller also toggles between upper and lower cases.) "←" "→": Moves the cursor to the arrow direction. " ": Removes a character on the left of the cursor. " ": Enters a space. • Pressing CLEAR on the remote controller will remove all the input characters. 3. After inputting, select "OK" with the cursors and press ENTER. The input name will be saved.

21

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting Item Default Value Setting Details AirPlay Password You can set a password of up to 31 characters so that only registered users can use AirPlayR. 1. Press ENTER to display the Edit screen. 2. Select a character or symbol with the cursors and press ENTER. Repeat it to input 31 or less characters. "A/a": Switches between upper and lower cases. (Pressing MODE on the remote controller also toggles between upper and lower cases.) "←" "→": Moves the cursor to the arrow direction. Troubleshooting Supplementary Information, etc. | • Wait for a while if "Network" cannot be selected. It will appear when the network feature is started. ■ 3. Bluetooth Setting Item Default Value Setting Details Bluetooth On Select whether or not to use the BLUETOOTH function. "On": Enables connection with a BLUETOOTH wireless technology enabled device by using the BLUETOOTH function. Select "On" also when making various BLUETOOTH settings. "Off": When not using the BLUETOOTH function

" ": Removes a character on the left of the cursor. " ": Enters a space. • To select whether to mask the password with "*" or display it in plain text, press MEMORY on the remote controller. • Pressing CLEAR on the remote controller will remove all the input characters. 3. After inputting, select "OK" with the cursors and press ENTER. Auto Input Change On The input of the unit will automatically be switched to "BLUETOOTH" when connection is made from a BLUETOOTH wireless technology enabled device to the unit. "On": The input will automatically become "BLUETOOTH" when a BLUETOOTH wireless technology enabled device is connected. "Off": The function is disabled. • If the input is not switched automatically, set to "Off" and change the input manually.

The input password will be saved. Usage Data No As a means of improving the quality of our products and services, we may collect information about your usage over the network. Select "Yes" if you agree to our collecting this information. Select "No" if you do not want us to collect this information. • You can set this after confirming the Privacy Policy. When you select "Usage Data" and press ENTER, the Privacy Policy is displayed. (The same screen is displayed once also when setting up the network connection.) If you agree to the collection of the information, this setting also becomes "Yes". Note that if you agree to the Privacy Policy but select "No" for this setting, the information will not be collected. Network Check - You can check the network connection. Press ENTER when "Start" is displayed. Auto Reconnect On This function automatically reconnects to the BLUETOOTH wireless technology enabled device connected last when you change the input to "BLUETOOTH". "On": When this function is to be used "Off": When this function is not to be used • This may not work with some BLUETOOTH wireless technology enabled devices.

22

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Setting Item Default Value Setting Details ■ 4. Power Management Troubleshooting Supplementary Information, etc. | Pairing Information - You can initialize the pairing information saved on this unit. Pressing ENTER when "Clear" is displayed initializes the pairing information stored in this unit. • This function does not initialize the pairing information on the BLUETOOTH wireless technology enabled device. When pairing the unit again with the device, be sure to clear the pairing information on the BLUETOOTH wireless technology enabled device in advance. For information on how to clear the pairing information, refer to the BLUETOOTH wireless technology enabled device's instruction manual. Setting Item Default Value Setting Details Sleep Timer Off Allows the unit to enter standby automatically when the specified time elapses. Select a value from "30 minutes", "60 minutes", and "90 minutes". "Off": Does not turn the unit to standby automatically. Auto Standby Off This setting places the unit on standby automatically after 20 minutes of inactivity without any video or audio input. (When "USB Power Out at Standby" or "Network Standby" is on, this becomes the HYBRID STANDBY mode which reduces the increase in power consumption to a minimum.) Device - Displays the name of the BLUETOOTH wireless technology enabled device connected to the unit. • The name is not displayed when "Status" is "Ready" and "Pairing". Status - Displays the status of the BLUETOOTH wireless technology enabled device connected to the unit. "Ready": Not paired "Pairing": Paired "Connected": Successfully connected • Wait for a while if "Bluetooth" cannot be selected. It will appear when the BLUETOOTH function is started up. Auto Standby in HDMI Standby Through USB Power Out at Standby "On": The unit will automatically enter standby mode ("AUTO STBY" will light). "Off": The unit will not automatically enter standby mode. • "Auto Standby" is displayed on the display and TV screen 30 seconds before the Auto Standby comes on. • "Auto Standby" does not work when Zone 2 is active. Off Enable or disable "Auto Standby" while "HDMI Standby Through" is on. "On": The setting will be enabled. "Off": The setting will be disabled. • This setting cannot be set to "On" if "Auto Standby" and "HDMI Standby Through" are set to "Off". Off Devices connected to the USB port are supplied with electricity even when this unit is in standby mode when this function is "On". • When using this feature, power consumption increases even when the unit is on standby, however, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only essential circuits are operating.

23

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Setting Item Default Value Setting Details Troubleshooting Supplementary Information, etc. | 6. Multi Zone Network Standby On When this feature is turned "On", you can turn on the power of the unit via the network using an application such as Onkyo Remote that can control this unit. • When "Network Standby" is used, the power consumption increases even when the unit is on standby. However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating. • When the connection to the network is lost, "Network Standby" is disabled to reduce power consumption. Use the power button on the remote controller or main unit to turn the unit on if this happens. Bluetooth Wakeup Off This function wakes up the unit on standby by connecting a BLUETOOTH wireless technology enabled device. "On": When this function is to be used "Off": When this function is not to be used • Setting to "On" increases the power consumption even when the unit is on standby. Make settings related to Multi-zone Connection, such as the volume for the separate room. ■ 1. Zone 2 Setting Item Default Value Setting Details Maximum Volume Off Set the maximum value for Zone 2 to avoid too high volume. Select a value from "Off", "50" to "99". (When "3. Audio Adjust" - "Volume" - "Volume Display" is set to "Absolute") Power On Volume Last Set the Zone 2 volume level of when this unit is turned on. Select a value from "Last" (Volume level when the unit was turned off), "Min", "0.5" to "99.5" and "Max". (When "3. Audio Adjust" - "Volume" - "Volume Display" is set to "Absolute") • You cannot set a higher value than that of "Maximum Volume". ■ 2. Remote Play Zone Setting Item Default Value Setting Details

However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating. • This setting is fixed to "Off" if "Bluetooth" - "Auto Input Change" is set to "Off". • Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It will appear when the network feature is started. ■ 5. 12V Trigger Setting Item Default Value Setting Details Zone Main Set which zone to output the 12V trigger when playing. If you select "All", then the 12V trigger is output to all zones that are playing. Remote Play Zone Auto When playing using AirPlay or Spotify Connect, or when using the Music Server feature to play remotely from your PC, you can set whether to play in the main room (where this unit is) or in a separate room (ZONE 2). "Auto": When the main room input selector is NET, music is played in the main room. When the separate room input selector is NET and the main room is other than NET, then the music is played in the separate room. "Main", "Zone2": Select when limiting the play zone to a particular room. For example, when playing only in the separate room, select "Zone 2". • This feature may not work if something is already being played with the same network feature.

24

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

7. Miscellaneous ■ 3. Firmware Update Troubleshooting Supplementary Information, etc. |

Change the frequency step for the tuner, update the firmware, and perform Initial Setup, etc. ■ 1. Tuner Setting Item Default Value Setting Details Setting Item Default Value Setting Details Update Notice Enable Availability of a firmware update will be notified via network. "Enable": Notify updates "Disable": Disable notifications Version - The current firmware version will be displayed.

AM / FM Frequency Step ■ 2. Remote ID 10 kHz / 0.2 MHz Select a frequency step depending on your area of residence. Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz". • When this setting is changed, all radio presets are deleted. Update via NET Update via USB - Press ENTER to select when you want to update the firmware via network. • You will not be able to select this setting if you do not have Internet access or there is nothing to update. - Press ENTER to select when you want to update the firmware via USB. • You will not be able to select this setting if a USB storage device is not connected or there is

Setting Item Default Value Setting Details Remote ID 1 Select an ID for the unit's remote controller from "1", "2", and "3" to prevent interference between the unit and other ONKYO components that are installed in the same room. After changing the ID on the main unit, change the ID on the remote controller accordingly with the following procedure. While holding down MODE, press the following buttons for about 3 seconds. • To change the remote controller ID to "1": (The remote indicator flashes once.) • To change the remote controller ID to "2": (The remote indicator flashes twice.) • To change the remote controller ID to "3": (The remote indicator flashes three times.) nothing to update in the USB storage device. • Wait for a while if "Firmware Update" cannot be selected. It will appear when the network feature is started. ■ 4. Initial Setup You can make the initial setup from the setup menu. • Wait for a while if "Initial Setup" cannot be selected. It will appear when the network feature is started. ■ 5. Lock Setting Item Default Value Setting Details Setup Parameter Unlocked Lock the Setup menu to protect the settings. "Locked": The menu is locked. "Unlocked": The menu is unlocked.

25

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Quick Menu You can quickly adjust settings you frequently use, such as tone adjustments, etc. Operation: You can make the settings on the TV screen while playing something. Press Q on the remote controller to display the Quick Menu. Subwoofer: Adjust the speaker level of the subwoofer while listening to some sound. • The adjustment you made will be reset to the previous status when you turn the unit to standby mode. ■ AccuEQ AccuEQ Room Calibration: Enable or disable the equalizer function that corrects for distortion caused by the acoustic environment of the room. If this is to be enabled, then normally you should select "On (All Ch)", and to disable just the front speakers you should select "On (ex. L/R)". The setting can be separately set to each input selector. Troubleshooting Supplementary Information, etc. | sound of lossy compressed files such as MP3 will be improved. The setting can be separately set to each input selector. The setting is effective in the signals of 48 kHz or less. The setting is not effective in the bitstream signals. • It cannot be set if the listening mode is Direct. Late Night: Make small sounds easily heard. It is useful when you need to reduce the volume while watching a movie late night. You can enjoy the effect only when playing Dolby series and DTS series input signals. • The setting cannot be used in the following cases. – If "Loudness Management" is set to "Off" when playing Dolby Digital Plus or Dolby TrueHD – When the input signal is DTS:X and "Dialog Control"

Quick Menu Tone Level AccuEQ Other BD/DVD Bass Treble Equalizer: Select "Preset 1" to "Preset 3" configured in "2. Speaker" - "Equalizer Settings" in the Setup menu. The same sound field setting is applied all ranges when set to "Off". Re-EQ, Re-EQ(THX): Adjust the soundtrack that was processed to enhance is other than 0 dB Center Spread: Adjust the width of the sound field of the front channel when playing in the Dolby Surround listening mode. To spread the width of the sound field to the left and right, set to "On". To concentrate sound in the center, set to "Off".

Select the item with the cursor / buttons of the remote controller and press ENTER to confirm your selection. Use the cursors to change the settings. • To return to the previous screen, press . • To exit the settings, press Q. ■ Tone Bass: Enhance or moderate the bass range of the front speakers. Treble: Enhance or moderate the treble range of the front speakers. • It cannot be set if the listening mode is Direct or THX. ■ Level Center: Adjust the speaker level of the center speaker while listening to some sound. its high pitch range, in order to make it suitable for home theater. In Re-EQ, the following listening modes can be used: Dolby Digital, Dolby Digital Plus, Dolby Surround, Dolby TrueHD, Multichannel, DTS, DTS-ES, DTS 96/24, DTS HD High Resolution Audio, DTS-HD Master Audio, DTS Neural:X, DTS Express and DSD. In Re-EQ(THX), the following listening modes can be used: THX Cinema and THX Select Cinema. • It cannot be set if the listening mode is Direct. ■ Other A/V Sync: If the video is behind the audio, you can delay the audio to offset the gap. Different settings can be set for each input selector. • It cannot be set if the listening mode is Direct. Music Optimizer: Improve the quality of the compressed audio. Playback • Depending on the speaker settings, this becomes "Off". Dialog Control: You can increase the dialog portion of the audio in 1 dB steps up to 6 dB so that you can make dialog easier to hear over background noise. • This cannot be set for content other than DTS:X. • The effect may not be selectable with some content. HDMI Out: Allows you to select the HDMI jack to output video signals from "MAIN", "SUB", and "MAIN+SUB".

26

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Web Setup You can make the settings for network features for this unit in an internet browser on a PC, smartphone, etc. 1. Press on the remote controller to display the Setup menu. 2. Select "5. Hardware" - "Network" with the cursors, then take a note of the IP address displayed in "IP Address". 3. Start the internet browser on your PC or smartphone and enter the IP address of the unit in the URL field. 4. Information for the unit (Web Setup screen) is displayed in the internet browser. 5. After changing the settings, select "Save" to save the settings. Device Information You can change the Friendly Name, set an AirPlay Password, etc. Control4: Register this unit if you are using a Control4 system. Firmware Update: Select the firmware update you have downloaded to your PC so you can update this unit. Network Setting Status: You can see information for the network such as the MAC address and IP address for this unit. Network Connection: You can select how to connect to the network. If you select "Wireless", select an access point from "Wi-Fi Setup" to connect. DHCP: You can change DHCP settings. If you select "Off", set "IP Address", "Subnet Mask", "Gateway", and "DNS Server" manually. Proxy: Display and set the URL for the proxy server. Troubleshooting Supplementary Information, etc. |

27

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Control Function Settings You can enable the control functions between the unit and external devices. Special devices or cable connections are necessary to enable the functions. For more information about installation, contact a store specializing in these products. ■ RS232 port Use this port for connection with an integrated control system that can enable home automation. Some integrated control systems provide a centralized operation with a single touch panel controller in order to control audio and video home appliances and security devices together. For more information about adopting an integrated control system, contact the specialized stores. ■ IR jack If you use a commercially available multiroom remote control kit with this jack, you can operate the unit with the remote controller even when you are in a separate room, or operate the unit with the remote controller even if its remote control sensor is difficult to see. IR receiver Connecting This unit block Remote controller Main room Zone Signal flow • Other companies may use indications other than IR on their products. Confirm in the instruction manual included with your components. • Refer to the instruction manual of the IR receiver for the types of cables required for connection. Troubleshooting Supplementary Information, etc. | ■ 12V trigger output jack You can enable power link operation when you connect the unit and an external device such as power amplifier equipped with 12V trigger input jack. When the desired input is selected on the unit, the power link operation will be activated with a control signal of maximum 12 V/100 mA output from the 12V TRIGGER OUT jack. You can select the zone to output the control signal in "5. Hardware" - "12V Trigger" in the Setup menu. For connection, use a monaural mini plug cable without a resistor.

28

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Firmware Update The updating function on this unit This unit has functionality to update the firmware (the system software) over a network or by the USB port. This enables us to make improvements to a variety of operations and to add features. • For the latest information on updates, visit our company's website. There is no need to update the firmware on this unit if there is no update available. • Before updating, make sure that the speaker setup microphone is not connected. • During an update, do not – Disconnect and reconnect any cable, USB storage device, speaker setup microphone or headphones, or perform any operation on the component such as turn off its power – Accessing this unit from a PC or smartphone using concerning your use of the program or the accompanying online documentation, regardless of legal theory, and whether arising in tort or contract. In no event will our company be liable to you or any third party for any special, indirect, incidental, or consequential damages of any kind, including, but not limited to, compensation, reimbursement or damages on account of the loss of present or prospective profits, loss of data, or for any other reason whatsoever. Troubleshooting Supplementary Information, etc. | Updating the Firmware via Network Preparation: • Check that the unit is turned on, and the connection to the Internet is secured. • Turn off the controller component (PC etc.) connected to the network. • Stop any playing Internet radio, USB storage device, or server content. • If the multi-zone function is active, turn it off. • If "HDMI CEC" is set to "On", set it to "Off". – Press on the remote controller. Then, after selecting "5. Hardware" - "HDMI" and pressing ENTER, select "HDMI CEC" and select "Off". * The description may differ from the on-screen display but that will not change the way to operate or the function. ■ Update 1. Press on the remote controller. The Setup menu is displayed on the TV screen. Setup

an application • The update may take about 20 minutes to complete for either method: via network or via USB. Furthermore, existing settings are guaranteed regardless of the method used for update. Note that when this unit is connected to a network, you may see notifications about firmware updates on the 1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Hardware 6. Multi Zone 7. Miscellaneous 1. TV Out / OSD 2. HDMI Input 3. Video Input 4. Digital Audio Input 5. Analog Audio Input

display. To execute updating, select "Update Now" with the cursor buttons of the remote controller and press ENTER. The unit automatically turns itself into standby mode after "Completed!" appears on the display, and updating will be complete. Disclaimer: The program and accompanying online documentation are furnished to you for use at your own risk. Our company will not be liable and you will have no remedy for damages for any claim of any kind whatsoever 2. Select "7. Miscellaneous" - "Firmware Update" - "Update via NET" with the cursors in order, then press ENTER.

29

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Setup 1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Hardware 6. Multi Zone 7. Miscellaneous 1. Tuner 2. Remote ID 3. Firmware Update 4. Initial Setup 5. Lock Error Code • *-01, *-10: Ethernet cable not found. Connect the Ethernet cable properly. • *-02, *-03, *-04, *-05, *-06, *-11, *-13, *-14, * -16, *-17, *-18, *-20, *-21: Internet connection error. Check the following: – The router is turned on – This unit and the router are connected via the network Troubleshooting Supplementary Information, etc. | Updating via USB Preparation: • Prepare a 128MB or larger USB storage device. FAT16 or FAT32 file system format. – Media inserted in a USB card reader may not be used for this function. – USB storage devices with security function are not supported. – USB hubs and USB devices with hub function are

• If "Firmware Update" is grayed out and cannot be selected, wait for a while until it starts up. • You will not be able to select "Update via NET" if there is nothing to update. 3. Press ENTER with "Update" selected to start update. • During the update, the TV screen may go black depending on the updated program. In that case, check the progress on the display of the unit. The TV screen will remain black until the update is complete and the power is turned on again. • "Completed!" is displayed when the update is complete. 4. Press ON/STANDBY on the main unit to turn the unit into standby mode. The process is completed and your firmware is updated to the latest version. • Do not use on the remote controller. ■ If an Error Message is Displayed When an error occurs, "*-** Error!" is displayed on the display of the unit. ("*" represents an alphanumeric character.) Check the following: Try to disconnect and then connect again the power to the unit and router. This may solve the problem. If you are still unable to connect to the Internet, the DNS server or proxy server may be temporarily down. Check the service status with your ISP provider. • Others Disconnect then reconnect the AC power cord, then repeat from the beginning. not supported. Do not connect these devices to the unit. • Delete any data stored on the USB storage device. • Turn off the controller component (PC etc.) connected to the network. • Stop any playing Internet radio, USB storage device, or server content. • If the multi-zone function is active, turn it off. • If "HDMI CEC" is set to "On", set it to "Off". – Press on the remote controller. Then, after selecting "5. Hardware" - "HDMI" and pressing ENTER, select "HDMI CEC" and select "Off". * Some USB storage devices may take long to load, may not be loaded correctly, or may not be correctly fed depending on the device or their content. * Our company will not be liable whatsoever for any loss or damage of data, or storage failure arising from the use of the USB storage device with this unit. Thank you for your understanding. * The description may differ from the on-screen display but that will not change the way to operate or the function. ■ Update 1. Connect the USB storage device to your PC. 2. Download the firmware file from our company's website to your PC and unzip. Firmware files are named in the following way: ONKAVR****_************.zip Unzip the file on your PC. The number of unzipped files and folders varies depending on the model. 3. Copy all unzipped files and folders to the root folder of the USB storage device. • Make sure to copy the unzipped files.

30

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

4. Connect the USB storage device to the USB port of the unit. • If you connect a USB hard disk drive to the USB port of the unit, we recommend that you use its AC adapter to power it. • If the USB storage device has been partitioned, each section will be treated as an independent device. 5. Press on the remote controller. The Setup menu is displayed on the TV screen. Setup TV screen will remain black until the update is complete and the power is turned on again. • During the update, do not turn off, or disconnect then reconnect the USB storage device. • "Completed!" is displayed when the update is complete. 8. Disconnect the USB storage device from the unit. 9. Press ON/STANDBY on the main unit to turn the unit into standby mode. The process is completed and your firmware is updated to the latest version. • Do not use on the remote controller. Troubleshooting Supplementary Information, etc. |

1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Hardware 6. Multi Zone 7. Miscellaneous 1. TV Out / OSD 2. HDMI Input 3. Video Input 4. Digital Audio Input 5. Analog Audio Input

6. Select "7. Miscellaneous" - "Firmware Update" - "Update via USB" with the cursors in order, then press ENTER. Setup ■ If an Error Message is Displayed When an error occurs, "*-** Error!" is displayed on the display of the unit. ("*" represents an alphanumeric character.) Check the following:

1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Hardware 6. Multi Zone 7. Miscellaneous 1. Tuner 2. Remote ID 3. Firmware Update 4. Initial Setup 5. Lock Error Code • *-01, *-10: USB storage device not found. Check whether the USB storage device or USB cable is correctly inserted to the USB port of the unit. Connect the USB storage device to an external power source if it has its own power supply.

• If "Firmware Update" is grayed out and cannot be selected, wait for a while until it starts up. • You will not be able to select "Update via USB" if there is nothing to update. 7. Press ENTER with "Update" selected to start update. • During the update, the TV screen may go black depending on the updated program. In that case, check the progress on the display of the unit. The • *-05, *-13, *-20, *-21: The firmware file is not present in the root folder of the USB storage device, or the firmware file is for another model. Retry from the download of the firmware file. • Others Disconnect then reconnect the AC power cord, then repeat from the beginning.

31

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Selecting Listening Modes Select the optimum listening mode for movies, TV, music, and games by repeatedly pressing the MOVIE/TV, MUSIC, and GAME buttons. 1. During play, press one of the following three buttons on the remote controller. 2. Press the selected button repeatedly to switch the modes displayed on the display of the unit. For details on the effects of each of the listening modes see "Listening Mode Effects". For listening modes selectable for each of the audio formats in the input signals, refer to "Selectable Listening Modes". Troubleshooting Supplementary Information, etc. |

32

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Listening Mode Effects In alphabetical order ■ AllCh Stereo This mode is ideal for background music. Stereo sound is played through the surround speakers as well as the front speakers, creating a stereo image. ■ Direct This listening mode can be selected for all input signals. Processing that affects sound quality is shut down so sound closer to the original is reproduced. Speakers play the sound field according to the number of channels in the input signal, so there would be output from only the front speakers for a two-channel signal, for example. ■ Dolby Atmos This mode faithfully reproduces the sound design recorded in the Dolby Atmos audio format. The Dolby Atmos audio format has been implemented in movie theaters equipped with the latest facilities and enables a revolutionary sound experience in home theaters. Unlike existing surround systems, Dolby Atmos doesn't rely on channels, but rather enables the accurate placement of sound objects that have independent motion in a three-dimensional space with even greater clarity. Dolby Atmos is an optional audio format on Blu ray Discs and achieves a three-dimensional sound field by introducing a sound field above the listener. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ Dolby D (Dolby Digital) This mode faithfully reproduces the sound design recorded in the Dolby Digital audio format. Dolby Digital is a multi-channel digital format developed by Dolby Laboratories, Inc. widely adopted for use in movie production. It is also a standard audio format on DVD-Video and Blu-ray Discs. It is possible to record a maximum of 5.1 channels on a DVD-Video or Blu-ray Disc; two front channels, a center channel, two surround channels, and the LFE channel dedicated to the bass region (sound elements for the subwoofer). • To enable transfer of this audio format, connect via digital cable and set audio output on the player to bitstream output. ■ Dolby D+ (Dolby Digital Plus) This mode faithfully reproduces the sound design recorded in the Dolby Digital Plus audio format. The Dolby Digital Plus format is a revision based on Dolby Digital, increasing the number of channels and endeavoring to improve sound quality by giving more flexibility in data bit rates. Dolby Digital Plus is used as an optional audio format on Blu-ray Discs, based on 5.1ch, but with additional channels such as the surround back channel added for a maximum of 7.1ch. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ Dolby Surround This listening mode allows you to expand the playback signal to 5.1 channels or 7.1 channels to suit the connected speaker configuration when the input signal is 2 channels or 5.1 channels. Along with past speaker setups, this is also compatible with playback systems for Dolby Atmos that include Dolby speaker technology. ■ Dolby TrueHD This mode faithfully reproduces the sound design recorded in the Dolby TrueHD audio format. The Dolby TrueHD audio format is a reversible format expanded based on the lossless compression technology referred to as MLP, and it makes it possible to faithfully reproduce the master audio recorded in the studio. Dolby TrueHD is used as an optional audio format on Blu-ray Troubleshooting Supplementary Information, etc. | Discs, based on 5.1ch, but with additional channels such as the surround back channel added for a maximum of 7.1ch. 7.1ch is recorded at 96 kHz/24bit, and 5.1ch is recorded at 192 kHz/24bit. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ DSD Mode suitable for playing sources recorded in DSD. • This unit supports DSD signals input through HDMI IN. However, depending on the connected player, better sound is possible when output from the PCM output of the player. • This listening mode cannot be selected if the output setting on your Blu-ray Disc/DVD player is not set to DSD. ■ DTS This mode faithfully reproduces the sound design recorded in the DTS audio format. The DTS audio format is a multi-channel digital format developed by DTS, Inc. This format is an optional audio format on DVD-Video and a standard on Blu-ray Discs. It enables recording of 5.1 channels; two front channels, a center channel, two surround channels, and the LFE channel dedicated to the bass region (sound elements for the subwoofer). The content is recorded with a rich volume of data, with maximum sampling rate of 48 kHz at a resolution of 24 bits and a bit rate of 1.5 Mbps. • To enable transfer of this audio format, connect via digital cable and set audio output on the player to bitstream output. ■ DTS 96/24 This mode faithfully reproduces the sound design recorded in the DTS 96/24 audio format. The DTS 96/24 format is an optional audio format on DVD-Video and Blu-ray Discs. It enables recording of 5.1 channels; two front channels, a center channel, two surround channels, and the LFE channel dedicated to the bass region (sound elements for the subwoofer). Detailed

33

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

reproduction is achieved by recording the content at a sampling rate of 96 kHz at a resolution of 24 bits. • To enable transfer of this audio format, connect via digital cable and set audio output on the player to bitstream output. ■ DTS Express This mode faithfully reproduces the sound design recorded in the DTS Express audio format. DTS Express is used as an optional audio format on Blu ray Discs, based on 5.1ch, but with channels such as the surround back channel added for a maximum of 7.1ch. It also supports low bit rates. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ DTS-HD HR (DTS-HD High Resolution Audio) This mode faithfully reproduces the sound design recorded in the DTS-HD High Resolution Audio audio format. DTS-HD High Resolution Audio is used as an optional audio format on Blu-ray Discs, based on 5.1ch, but with additional channels such as the surround back channel added for a maximum of 7.1ch. It can be recorded at a sampling rate of 96 kHz with a resolution of 24 bits. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ DTS-HD MSTR (DTS-HD Master Audio) This mode faithfully reproduces the sound design recorded in the DTS-HD Master Audio audio format. DTS-HD Master Audio is used as an optional audio format on Blu-ray Discs, based on 5.1ch, but with additional channels such as the surround back channel added for a maximum of 7.1ch, recorded using lossless audio reproduction technology. 96 kHz/24bit is supported with 7.1ch, and 192 kHz/24bit is supported with 5.1ch. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ DTS Neural:X This listening mode allows you to expand the playback signal to 5.1 channels or 7.1 channels to suit the connected speaker configuration when the input signal is 2 channels or 5.1 channels. ■ DTS:X This mode faithfully reproduces the sound design recorded in the DTS:X audio format. The DTS:X audio format is a combination of the mixing methodology based on past channel based formats (5.1ch and 7.1ch) and object based dynamic audio mixing, and it is characterized by the precise positioning of sounds and the ability to express movement. • To enable transfer of this audio format, connect via HDMI cable and set audio output on the player to bitstream output. ■ ES Discrete (DTS-ES Discrete) This mode faithfully reproduces the sound design recorded in the DTS-ES Discrete audio format. DTS-ES Discrete is used as an optional audio format on DVD-Video and Blu-ray Discs, based on 5.1ch, but with an additional monaural surround back channel added for a maximum of 6.1ch. • To enable transfer of this audio format, connect via digital cable and set audio output on the player to bitstream output. ■ ES Matrix (DTS-ES Matrix) This mode faithfully reproduces the sound design recorded in the DTS-ES Matrix audio format. DTS-ES Matrix is used as an optional audio format on DVD-Video and Blu-ray Discs, based on 5.1ch, but with a monaural surround back channel included by matrix encoding. The matrix decoder on this unit decodes this during playback to produce 6.1 channels. • To enable transfer of this audio format, connect via digital cable and set audio output on the player to bitstream output. Troubleshooting Supplementary Information, etc. | ■ Full Mono In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room. ■ Game-Action This mode is suitable for games with a lot of action. ■ Game-Rock This mode is designed to help you enjoy games with rock content. ■ Game-RPG This mode is best for role-playing games. ■ Game-Sports This mode is great for sports games. ■ Mono In this mode, when the input signal is analog or PCM, the left and right front speakers output the sound in monaural. ■ Multich (Multichannel) Mode suitable for playing sources recorded in multichannel PCM. ■ Orchestra Suitable for classical or operatic music. This mode emphasizes the surround channels in order to widen the sound image, and simulates the natural reverberation of a large hall. ■ Stereo In this mode, sound is output from the front left and right speakers and subwoofer. ■ Studio-Mix Suitable for rock or pop music. Listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

34

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

■ T-D (Theater-Dimensional) In this mode, you can enjoy a virtual playback of multichannel surround sound even with only two or three speakers. This works by controlling how sounds reach the listener's left and right ears. ■ THX THX is a series of specifications for the accurate reproduction of movies propounded by the film director George Lucas. THX listening modes include the THX Cinema mode, and using technology such as THX Loudness Plus and Timbre Matching, the sound of a movie theater is reproduced accurately. THX technology: A movie soundtrack is mixed in large-scale theater specially made for mixing that is called a dubbing stage on the assumption that the soundtrack is played in such theaters with similar equipment and conditions. These sound tracks are recorded as is, even when recording to a DVD-Video, for example, without making any modifications to suit a home theater. THX technology is able to reproduce the theater sound in a home theater environment by minimizing acoustic and spatial deviation. • THX Loudness Plus THX Loudness Plus is a new volume control technology featured in THX Ultra and THX Select certified AV receivers. With THX Loudness Plus, home theater audiences can experience the rich details of surround sound at any volume level. If the volume is turned down below the reference level, elements of sound in a certain range are lost or the sound is perceived differently by audience. THX Loudness Plus compensates for the tonal and spatial shifts that occur when the volume level is reduced, by intelligently correcting the levels of the surround channels and their frequency response in the environment. • Re-EQ The speakers for the front channel are installed behind the screen in a movie theater. For this reason the high range is enhanced in the front channel of the sound track to take account of acoustic characteristics such as the necessity to penetrate the screen. Re-EQ adjusts soundtrack with enhanced high range to make it suitable for home theater. • Timbre Matching The perception of the human ear differs depending on the direction of the sound. Movie theaters have many surround speakers installed so they are great at surrounding the viewer with natural sound, but home theaters have only two surround speakers installed. The Timbre Matching function filters the signals sent to the surround speakers and adjusts the tonal characteristics of front speakers and surround speakers to create smooth sound movement from front speakers to surround speakers. • Adaptive Decorrelation Although movie theaters have many surround speakers to surround the room with sound, home theaters normally have only two surround speakers. Such two surround speakers give a headphone-like sound, not a broad and embracing surround sound. If the listener moves away from the middle of the surround speakers, sound from the surround speakers mixes with that from the near speakers and cannot be distinguished any more. Adaptive Decorrelation slightly changes the time axis and phase between the surround channels so you can enjoy the same kind of breadth of sound you can in a movie theater even with only two surround speakers. • ASA (Advanced Speaker Array) ASA is a technology patented by THX to provide a broad surround sound experience by adjusting the side and back surround speaker sounds respectively. When installing the surround back speakers, first select the distance between the two surround back speakers in the THX Audio settings. This setting optimizes the surround sound environment. THX listening modes: – THX Cinema: Use in a home theater environment for playing a soundtrack that was recorded with the intention of it being played in a movie theater or similar large area. In this mode, THX Loudness Plus is set to the theater level and Re-EQ, Timbre Matching, and Adaptive Decorrelation are all enabled. Troubleshooting Supplementary Information, etc. | – THX Games: Use for high-fidelity spatial reproduction of game sound. THX Loudness Plus is set to a level suited to the audio level of the game and Timbre Matching is enabled. – THX Music: Use mainly for music sources that are clearly mastered to a much higher quality than movie audio. THX Loudness Plus is set to a level suited to the playback of music and Timbre Matching is enabled. – THX S Cinema (THX Select Cinema): The THX Select Cinema mode provides a high-quality surround sound experience by expanding movie sources recorded in 5.1 ch for 7.1 ch playback. In this mode, the THX ASA processing technology gives smooth transition between side and back surround sounds creating the best atmosphere and directional sense of surround sound. – THX S Games (THX Select Games): Select the THX Select Games mode to play game sound recorded in a multichannel format. In this mode, the THX ASA processing technology creates a 360-degree sound field with game sound recorded in PCM, DTS, Dolby Digital and other 5.1 ch formats. – THX S Music (THX Select Music): Select THX Select Music to play music sources recorded in a multichannel format. In this mode, the THX ASA processing technology creates a broad and stable back sound field for music sources recorded in 5.1ch such as DTS, Dolby Digital, and DVD-Audio. ■ TV Logic Suitable for TV shows produced in a TV studio. This mode enhances the surround effects to the entire sound to give clarity to voices and create a realistic acoustic image. ■ Unplugged Suitable for acoustic instruments, vocals and jazz. This mode emphasizes the front stereo image, giving the impression of being right in front of the stage.

35

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Selectable Listening Modes You can select a variety of listening modes to suit the audio format of the signal being input. Refer to the following for the listening mode choices. • Listening modes available when headphones are connected are: Mono, Direct, and Stereo. ■ MOVIE/TV button This is a list of listening modes you can select according to the audio format of the input signal. Input Format Listening Mode Analog Direct Mono Dolby Surround DTS Neural:X THX Cinema🞵1 TV Logic🞵2 AllCh Stereo🞵3 Full Mono🞵3 T-D 🞵1 Surround speakers need to be installed. 🞵2 Surround speakers or height speakers need to be installed. 🞵3 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode Troubleshooting Supplementary Information, etc. | Input Format Listening Mode Multich PCM Direct Multich🞵1 Dolby Surround DTS Neural:X THX Cinema🞵2 THX S Cinema🞵3 TV Logic🞵4 AllCh Stereo🞵5 Full Mono🞵5 T-D 🞵1 A center speaker or surround speakers need to be installed. 🞵2 Surround speakers need to be installed. 🞵3 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵4 Surround speakers or height speakers need to be installed. 🞵5 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DSD Direct

PCM Music files (except DSD/ Dolby TrueHD) Direct Mono Dolby Surround DTS Neural:X THX Cinema🞵1 TV Logic🞵2 AllCh Stereo🞵3 Full Mono🞵3 T-D DSD🞵1 🞵2 Dolby Surround DTS Neural:X THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6

🞵1 Surround speakers need to be installed. 🞵2 Surround speakers or height speakers need to be installed. 🞵3 A center speaker, surround speakers, or height speakers need to be installed. T-D 🞵1 Cannot be selected when the input format is monaural or 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

36

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode Input Format Listening Mode Troubleshooting Supplementary Information, etc. | Input Format Listening Mode

Dolby Atmos • You can select the Dolby Digital Plus or Dolby TrueHD listening modes if surround back speakers or height speakers are not connected. Direct Dolby Atmos TV Logic AllCh Stereo Full Mono T-D Dolby D+ Direct Dolby D+🞵1 🞵2 Dolby Surround THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 DTS Direct DTS🞵1 🞵2 DTS Neural:X THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5

Input Format Listening Mode Dolby D Direct Dolby D🞵1 🞵2 Dolby Surround THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode Dolby TrueHD Direct Dolby TrueHD🞵1 🞵2 Dolby Surround THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS 96/24 Direct DTS 96/24🞵1 🞵2 DTS Neural:X THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

37

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode DTS Express Direct DTS Express🞵1 🞵2 DTS Neural:X THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS-HD HR Direct DTS-HD HR🞵1 🞵2 DTS Neural:X THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS-HD MSTR Direct DTS-HD MSTR🞵1 🞵2 DTS Neural:X THX Cinema🞵3 THX S Cinema🞵4 TV Logic🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS-ES Direct DTS🞵1 ES Matrix🞵2 ES Discrete🞵2 DTS Neural:X THX Cinema🞵3 TV Logic🞵4 AllCh Stereo🞵5 Full Mono🞵5 T-D 🞵1 This can only be selected when no surround back speaker is connected. 🞵2 Surround back speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround speakers or height speakers need to be installed. 🞵5 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode DTS:X Direct DTS:X TV Logic🞵1 AllCh Stereo🞵2 Full Mono🞵2 T-D 🞵1 Surround speakers or height speakers need to be installed. 🞵2 A center speaker, surround speakers, or height speakers need to be installed.

38

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

■ MUSIC button Input Format Listening Mode Troubleshooting Supplementary Information, etc. | Input Format Listening Mode

This is a list of listening modes you can select according to the audio format of the input signal. Input Format Listening Mode Analog Direct Stereo Dolby Surround DTS Neural:X THX Music🞵1 Orchestra🞵2 Unplugged🞵2 PCM Music files (except DSD/ Dolby TrueHD) Direct Stereo Dolby Surround DTS Neural:X THX Music🞵1 Orchestra🞵2 Unplugged🞵2 Studio-Mix🞵2 AllCh Stereo🞵3 Full Mono🞵3 DSD Direct Stereo DSD🞵1 🞵2 Dolby Surround DTS Neural:X THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5

Studio-Mix🞵2 AllCh Stereo🞵3 Full Mono🞵3 🞵1 Surround speakers need to be installed. 🞵2 Surround speakers or height speakers need to be installed. 🞵3 A center speaker, surround speakers, or height speakers need to be installed. 🞵1 Surround speakers need to be installed. 🞵2 Surround speakers or height speakers need to be installed. 🞵3 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode Multich PCM Direct Stereo Multich🞵1 Dolby Surround AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is monaural or 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode

DTS Neural:X THX Music🞵2 THX S Music🞵3 Orchestra🞵4 Unplugged🞵4 Studio-Mix🞵4 AllCh Stereo🞵5 Full Mono🞵5 🞵1 A center speaker or surround speakers need to be installed. 🞵2 Surround speakers need to be installed. 🞵3 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵4 Surround speakers or height speakers need to be installed. 🞵5 A center speaker, surround speakers, or height speakers need to be installed. Dolby Atmos • You can select the Dolby Digital Plus or Dolby TrueHD listening modes if surround back speakers or height speakers are not connected. Direct Stereo Dolby Atmos Orchestra Unplugged Studio-Mix AllCh Stereo Full Mono

39

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode Dolby D Direct Stereo Dolby D🞵1 🞵2 Dolby Surround THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode Dolby D+ Direct Stereo Dolby D+🞵1 🞵2 Dolby Surround THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode Dolby TrueHD Direct Stereo Dolby TrueHD🞵1 🞵2 Dolby Surround THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

40

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode DTS Direct Stereo DTS🞵1 🞵2 DTS Neural:X THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS 96/24 Direct Stereo DTS 96/24🞵1 🞵2 DTS Neural:X THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode DTS Express Direct Stereo DTS Express🞵1 🞵2 DTS Neural:X THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

41

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode DTS-HD HR Direct Stereo DTS-HD HR🞵1 🞵2 DTS Neural:X THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS-HD MSTR Direct Stereo DTS-HD MSTR🞵1 🞵2 DTS Neural:X THX Music🞵3 THX S Music🞵4 Orchestra🞵5 Unplugged🞵5 Studio-Mix🞵5 AllCh Stereo🞵6 Full Mono🞵6 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode DTS-ES Direct Stereo DTS🞵1 ES Matrix🞵2 ES Discrete🞵2 DTS Neural:X THX Music🞵3 Orchestra🞵4 Unplugged🞵4 Studio-Mix🞵4 AllCh Stereo🞵5 Full Mono🞵5 🞵1 This can only be selected when no surround back speaker is connected. 🞵2 Surround back speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround speakers or height speakers need to be installed. 🞵5 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS:X Direct Stereo DTS:X Orchestra🞵1 Unplugged🞵1 Studio-Mix🞵1 AllCh Stereo🞵2 Full Mono🞵2 🞵1 Surround speakers or height speakers need to be installed. 🞵2 A center speaker, surround speakers, or height speakers need to be installed.

42

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

■ GAME button Input Format Listening Mode Troubleshooting Supplementary Information, etc. | Input Format Listening Mode

This is a list of listening modes you can select according to the audio format of the input signal. Input Format Listening Mode Analog Direct Dolby Surround DTS Neural:X THX Games🞵1 Game-RPG🞵2 Game-Action🞵2 Game-Rock🞵2 Game-Sports🞵2 PCM Music files (except DSD/ Dolby TrueHD) Direct Dolby Surround DTS Neural:X THX Games🞵1 Game-RPG🞵2 Game-Action🞵2 Game-Rock🞵2 Game-Sports🞵2 AllCh Stereo🞵3 Full Mono🞵3 T-D Multich PCM Direct Multich🞵1 Dolby Surround DTS Neural:X THX Games🞵2 THX S Games🞵3 Game-RPG🞵4 Game-Action🞵4 Game-Rock🞵4 Game-Sports🞵4 AllCh Stereo🞵5

AllCh Stereo🞵3 Full Mono🞵3 T-D 🞵1 Surround speakers need to be installed. 🞵2 Surround speakers or height speakers need to be installed. 🞵3 A center speaker, surround speakers, or height speakers need to be installed. 🞵1 Surround speakers need to be installed. 🞵2 Surround speakers or height speakers need to be installed. 🞵3 A center speaker, surround speakers, or height speakers need to be installed. Full Mono🞵5 T-D 🞵1 A center speaker or surround speakers need to be installed. 🞵2 Surround speakers need to be installed. 🞵3 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵4 Surround speakers or height speakers need to be installed. 🞵5 A center speaker, surround speakers, or height speakers need to be installed.

43

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode DSD Direct DSD🞵1 🞵2 Dolby Surround DTS Neural:X THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is monaural or 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode Input Format Listening Mode Dolby D Direct Dolby D🞵1 🞵2 Dolby Surround THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode Dolby D+ Direct Dolby D+🞵1 🞵2 Dolby Surround THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

Dolby Atmos • You can select the Dolby Digital Plus or Dolby TrueHD listening modes if surround back speakers or height speakers are not connected. Direct Dolby Atmos Game-RPG Game-Action Game-Rock Game-Sports AllCh Stereo Full Mono T-D

44

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode Dolby TrueHD Direct Dolby TrueHD🞵1 🞵2 Dolby Surround THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS Direct DTS🞵1 🞵2 DTS Neural:X THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode DTS 96/24 Direct DTS 96/24🞵1 🞵2 DTS Neural:X THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

45

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual

Input Format Listening Mode DTS Express Direct DTS Express🞵1 🞵2 DTS Neural:X THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS-HD HR Direct DTS-HD HR🞵1 🞵2 DTS Neural:X THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. | Input Format Listening Mode DTS-HD MSTR Direct DTS-HD MSTR🞵1 🞵2 DTS Neural:X THX Games🞵3 THX S Games🞵4 Game-RPG🞵5 Game-Action🞵5 Game-Rock🞵5 Game-Sports🞵5 AllCh Stereo🞵6 Full Mono🞵6 T-D 🞵1 Cannot be selected when the input format is 2 ch. 🞵2 A center speaker or surround speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround back speakers need to be installed. Can be selected when the input format is 5.1 ch. 🞵5 Surround speakers or height speakers need to be installed. 🞵6 A center speaker, surround speakers, or height speakers need to be installed.

46

> Specifications > Advanced Setup > Listening Modes > Network Functions > Basic Manual Input Format Listening Mode DTS-ES Direct DTS🞵1 ES Matrix🞵2 ES Discrete🞵2 DTS Neural:X THX Games🞵3 Game-RPG🞵4 Game-Action🞵4 Game-Rock🞵4 Game-Sports🞵4 AllCh Stereo🞵5 Full Mono🞵5 T-D 🞵1 This can only be selected when no surround back speaker is connected. 🞵2 Surround back speakers need to be installed. 🞵3 Surround speakers need to be installed. 🞵4 Surround speakers or height speakers need to be installed. 🞵5 A center speaker, surround speakers, or height speakers need to be installed. Input Format Listening Mode DTS:X Direct DTS:X Game-RPG🞵1 Game-Action🞵1 Game-Rock🞵1 Game-Sports🞵1 AllCh Stereo🞵2 Full Mono🞵2 T-D 🞵1 Surround speakers or height speakers need to be installed. 🞵2 A center speaker, surround speakers, or height speakers need to be installed. Troubleshooting Supplementary Information, etc. |

47


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply