ONEODIO A10 (01) PDF MANUAL

Connect the included USB Type-C charging cable to the USB-C port on the headphones and the other end to a 5V/1A power source (like a USB wall adapter or computer port).

The indicator light will be red while charging and turn blue when fully charged.

A full charge takes approximately 2 hours.

Press and hold the Power button (located between the volume buttons) for 5 seconds to turn the headphones on and enter Bluetooth pairing mode. To turn the headphones off, press and hold the Power button (duration not specified, but typically a few seconds until the indicator light turns off).

1. Press and hold the Power button for 5 seconds to turn the headphones on and enter pairing mode. The indicator light will typically flash to indicate pairing mode.

2. On your phone or device, turn on Bluetooth.

3. Scan for available devices and select “OneOdio A10” from the list to connect.

1. Follow the steps to pair the headphones with the first device (Phone 1).

2. Turn off Bluetooth on Phone 1 or disconnect the headphones from Phone 1.

3. Put the headphones back into pairing mode by pressing and holding the Power button for 5 seconds.

4. On the second device (Phone 2), turn on Bluetooth, scan for devices, and select “OneOdio A10” to connect.

5. Turn Bluetooth back on for Phone 1. Go to the Bluetooth settings on Phone 1 and select “OneOdio A10” from the list of previously paired devices to reconnect.

6. The headphones should now be connected to both Phone 1 and Phone 2 simultaneously.

Play/Pause: Press the Power button once (x1).

Next Track: Press and hold the Volume Up (+) button for 1 second.

Previous Track: Press and hold the Volume Down (-) button for 1 second.

Volume Up: Press the Volume Up (+) button once (x1).

Volume Down: Press the Volume Down (-) button once (x1).

Answer Incoming Call: Press the Power button once (x1).

End Current Call: Press the Power button once (x1).

Reject Incoming Call: Press the Power button twice (x2).

When on a call (Tom) and another call comes in (Amy):

• Press the Power button twice (x2): Answer the incoming call (Amy) and put the current call (Tom) on hold (enters three-way mode).

• Press the Power button once (x1): Answer the incoming call (Amy) and hang up the current call (Tom).

• Press and hold the Power button for 2 seconds: Keep the current call (Tom) active and reject the incoming call (Amy).

During a three-party conference (one active, one on hold):

• Press the Power button twice (x2): Switch between the active call and the call on hold.

Press the Power button twice (x2).

Press the ANC button repeatedly to cycle through the different modes:

1. Press ANC button (x1): Activates Transparency Mode.

2. Press ANC button (x1 again): Activates ANC Mode.

3. Press ANC button (x1 again): Activates Normal Mode (ANC and Transparency off).

1. Press and hold the ANC button for 2 seconds: Activates Transparency Mode.

2. Once Transparency Mode is active, press the ANC button once (x1): Switches to ANC Mode.

3. Press the ANC button once (x1 again): Switches to Normal Mode (ANC and Transparency off).

Pressing and holding the ANC button for 2 seconds again will likely turn off the ANC/Transparency functions.

While the headphones are in pairing mode (after holding the power button for 5 seconds from off), press and hold the Volume Up (+) and Volume Down (-) buttons simultaneously for 5 seconds. This will reset the headphones and clear the stored Bluetooth pairing list.

Model Name:	A10
Input:	5 VDC, 560 mA
Battery Capacity:	800 mAh
Charging Time:	Approx. 2 hours
Playing Time (ANC + BT):	Approx. 40 Hours
Playing Time (BT Only):	Approx. 50 Hours
Playing Time (ANC Only):	Approx. 62 Hours
Noise Reduction Depth:	-35 dB
Driver Diameter:	40 mm
Sensitivity (Mic? Speaker? Not specified):	-42 ± 3 dB
Impedance:	32 Ω ± 15%
Frequency Response:	20 Hz – 40 KHz
Connection Distance:	10 m / 33 ft
Net Weight:	295 g

1 x OneOdio A10 Hybrid ANC Headphones

1 x EVA Case

1 x 3.5mm Audio Cable

1 x USB Type-C Charging Cable

1 x User Guide

You can contact the customer service team via:

Website: global.oneodio.com/pages/support or japan.oneodio.jp/pages/support

Phone: +862084003846 (Available Monday to Friday, 9:00 am – 6:30 pm, UTC +8 HKT)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

RF exposure statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.