NORDIC DELTACO ARM-0452 (01) PDF MANUAL

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your retailer for assistance. Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Deltaco or the retailer where you purchased the product.

Safety gear and proper tools must be used. This product should only be installed by a qualified person.

Ensure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Use the mounting screws provided and do not over tighten the mounting screws.

This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

Mounting the TV onto the stand (Step 6) requires two people.

Caution: Usage together with products heavier than the rated weight (do not exceed the marked max weight) may result in instability which can cause possible injury. Serious injury or property damage may occur.

1. Attach the two legs (A and B) to the central base piece (C) using the provided M8x20 screws (P-C) and the 6mm Allen key (P-G).

2. Screw the four casters (D) into the bottom of the legs. Use the provided wrench (P-E) to fully tighten them. Ensure the two locking casters are placed appropriately, usually at the front or back depending on preference.

1. Attach the lower pole (E) to the assembled base using four M8x80 bolts (P-B) and four washers (P-A). Tighten these using the 6mm Allen key (P-G).

2. Slide the plastic pole cover (G) over the top of the upper pole (F).

3. Insert the upper pole (F) into the lower pole (E).

4. Secure the upper pole (F) to the lower pole (E) using four M8x20 screws (P-C) and the 6mm Allen key (P-G).

1. Adjust the width of the brackets (H1) on the VESA plate holder (H) if necessary using the 5mm Allen key (P-F) on the adjustment screws (H2). Ensure the gap for the pole is greater than 4mm before attempting to mount.

2. Use a Phillips head screwdriver to loosen or tighten the height adjustment screws (H3) if needed.

3. Place the assembled VESA plate holder (H) onto the top of the upper pole (F).

4. Secure the VESA plate holder to the pole by tightening the clamp screw using the 5mm Allen key (P-F).

1. Hook the two vertical VESA mounting arms (I) onto the VESA plate holder (H). Ensure they are oriented correctly (check diagrams for “UP” orientation).

2. Slide the plastic end caps (J) onto the ends of the VESA plate holder (H).

3. Secure the bottom of the VESA mounting arms (I) to the VESA plate holder (H) using the safety screws (P-D) and a Phillips head screwdriver.

1. Determine the correct VESA screw size (M5, M6, or M8) and length required for your specific TV model (refer to your TV manual).

2. Ensure the VESA mounting arm assembly (“TOP” marking) is oriented towards the top of your TV.

3. For flat back TVs: Use appropriate screws (M-A: M5x14 or M-B: M6x14). Spacers (M-F) might be needed in some cases.

4. For curved or recessed back TVs: Use appropriate screws (M-C: M6x30, M-D: M8x30, or M-E: M8x50) along with the necessary combination of spacers (M-F, M-G, M-H) to ensure a secure fit without damaging the TV.

5. Attach the VESA arms to the back of the TV using the selected screws and spacers. Tighten securely with a Phillips head screwdriver, but do not overtighten.

1. This step requires two people for safety.

2. Carefully lift the TV with the attached VESA arms.

3. Hook the top of the VESA arms onto the top rail of the VESA plate holder (H) already mounted on the stand pole.

4. Lower the TV gently so the bottom of the VESA arms also rests against the plate holder.

5. Secure the TV by tightening the safety screws (H2, located at the bottom of the VESA arms) using a Phillips head screwdriver.

Route the TV cables through the integrated cable management system within the support pole. Use the provided cable clips (L) inside the pole cover to keep cables tidy. You may need the Allen keys (P-F, P-G) to access or adjust components for cable routing.

The height can be adjusted before fully securing the VESA plate holder (H) to the upper pole (F) during Step 3, or by loosening the clamp screw (using Allen key P-F), repositioning the VESA plate holder assembly along the pole, and retightening. The height range is typically between 1250mm and 1600mm (center of VESA plate). Ensure the TV is removed or adequately supported before adjusting the height.

No, this product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Check that the stand is secure and safe to use at regular intervals (at least every three months). Ensure all screws remain tight and there are no signs of damage or instability.