FREE ENGLISH NEMCO SS6L-4 (01) PDF USER GUIDE
FREE ENGLISH NEMCO SS6L-4 (01) PDF USER MANUAL
FREE ENGLISH NEMCO SS6L-4 (01) PDF OWNER GUIDE
FREE ENGLISH NEMCO SS6L-4 (01) PDF OWNER MANUAL
FREE ENGLISH NEMCO SS6L-4 (01) PDF REFERENCE GUIDE
FREE ENGLISH NEMCO SS6L-4 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH NEMCO SS6L-4 (01) PDF REFERENCE MANUAL
FREE ENGLISH NEMCO SS6L-4 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH NEMCO SS6L-4 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD NEMCO SS6L-4 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
NEMCO SS6L-4 (01) PDF SUMMARY:
What should be done before the first use of the stainless steel dispensers?
All components must be cleaned.
What should you be aware of regarding food and safety regulations?
According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Be aware of the product you are serving and the temperature the product is required to maintain.
How often should the stainless steel dispenser be cleaned?
Clean, rinse, sanitize, and dry parts at a minimum of every 24 hours. Always comply with local sanitization requirements.
How do you clean the stainless steel dispenser?
All components are dishwasher safe. Disassemble all six (6) parts. Clean with soap and hot water, rinse, sanitize and dry parts according to local sanitization requirements. Use supplied brush to scrub inside parts.
How to mount the nozzle?
Bend the outer portion of the nozzle inside out. Insert into opening. Tab of nozzle faces towards housing. Flip the outer portion of the nozzle over the end of tube.
How to insert dome?
Press the entire dome firmly, including the top portion.
How to insert the dome clip?
Ensure that the tab on bottom of the dome slides into the opening in the dome clip.
How to attach the hose to the pump housing?
Fit the holes in the hose over the pegs on the pump housing.
How to attach the connector to the hose?
Fit the bottom holes on hose over the pegs on the connector. Piercing end of the connector must face away from pump housing.
How to connect the pump to the pouch?
Place new pouch on countertop with fitment facing up. Place piercing end of connector in center of the fitment. Push firmly until pump snaps into place.
How to insert pouch and pump?
Insert into the dispenser shroud. Hold end of pouch up while guiding the pump into the slots inside the front of dispenser.
How to insert the lid?
Hold the lever up while inserting lid tabs into slots in back of dispenser shroud.
How to prime the pump?
Press lever several times until food is visible in discharge tube.
How to add corner guards?
Hook first tab into slot. Push firmly on second tab to snap into place.
How to remove the locking washer?
Use a flathead screwdriver to pry off the locking washer from the pin at the end of the link arms. Keep locking washer for step 4.
How to remove the pin?
Slide the pin out from the pair of link arms and portion holes.
How to align holes on link arms?
Select portion setting with hole for desired portion setting. Slide pin through all. Secure pin with locking washer.
How to optimize pouch evacuation?
Ensure ramp is in place.
What should you ensure when attaching the pump to the pouch?
Ensure that you hear a CLICK when attaching pump to pouch.
How can you prevent leaks?
Ensure that dome is pushed fully into pump housing.
What is a pro tip for fitting the hose onto pegs?
Clean water may be used as lubrication when fitting hose onto pegs.
CLICK HERE TO DOWNLOAD NEMCO SS6L-4 (01) PDF MANUAL