MIDEA VSS GX5 (01) PDF Document

When using your MIDEA VSS GX5, please adhere to the following safety instructions:

• This product is suitable for hard floors in an indoor environment, including waxed, stone, rubber, marble, granite, terrazzo, solid wood, composite, and bamboo floors, as well as glazed and ceramic tiles. It may not achieve the best results on uneven ground surfaces.

• Do not use this product near or on the surface of flammable and explosive objects, which may cause fire and explosion.

• Do not use this product near a working fireplace or heater to prevent deformation of the machine casing.

• Do not use it to clean high-temperature substances (unextinguished cigarette butts, matches, hot ash), ultra-fine substances (lime, cement, wood chips, gypsum powder, ashes, charcoal), dangerous substances (solvents, descaling agents), or chemical substances (acidic substances, detergents).

• Do not use this floor cleaner to absorb detergent, kerosene, gasoline, alcohol, paint, or perfume, as it may cause a short-circuit, fire, or explosion.

• Do not use this floor cleaner to absorb toner used in laser printers and copiers.

• Do not use this floor cleaner to absorb sharp or large objects like glass shards, small toys, pins, paper clips, stones, plaster, and large pieces of paper.

• Do not use this floor cleaner to absorb any burning or smoking objects, such as soot, burning cigarette butts, or matches.

• This product cannot be used to clean stains of strong grease, strong viscosity, or strong dyeing properties such as shoe polish, paint, and pigments.

• Do not touch the plug or any live part of the product with wet hands to avoid electric shock.

• Stop using the product if the plug is damaged. Please call service personnel for replacement.

• Keep airflow channels and moving parts away from long hair, loose clothing, fingers, and other body parts. Do not point the suction tube, accessory tip, or tool at eyes or ears, or put them in your mouth.

• Use only the cleaning agent produced by our company or an approved manufacturer.

• If you notice electric leakage, motor over-temperature, abnormal noise, a peculiar smell, or weak suction, stop using the MIDEA VSS GX5 immediately and call service personnel.

• After use, clean the wastewater tank promptly to avoid peculiar smells and keep the ventilation path unobstructed.

• Store the machine in a dry place after use. A humid environment can affect the insulation and service life of the appliance.

• Do not soak or rinse the floor cleaner or floor brush in water.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities if they have been given supervision or instruction. Cleaning and user maintenance should not be done by children without supervision.

• Children should not play with the appliance.

• Check the suction nozzle regularly and clear any blockages.

• Turn off the power before replacing the brush.

• Do not disassemble the enclosed machine without permission. There are no user-serviceable parts.

• Using a voltage that does not match the specifications will cause damage. The correct rated voltage is marked on the nameplate.

• Be extra cautious when cleaning stairs to prevent falling.

• Do not shake or impact the machine to prevent wastewater from flowing into the motor.

• When the motor is working, do not lift, carry, or place the machine on its side.

• To prevent tip-over, place the machine against a wall after use.

• Do not use the floor cleaner before the clean water tank and wastewater tank are installed properly.

• Do not place objects in or block the outlet.

• Do not wet the machine body, as it may cause damage and fire due to a short circuit.

• Only use the provided docking station to charge the battery.

• The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.

• Mix and clean according to instructions. It is recommended to use cleaning liquid produced by our company or manufacturers approved by our company, which do not contain acid, alkali solutions or substances harmful to the environment.

• If a large amount of cleaning liquid is added, more foam will be generated when used, which may infiltrate into the motor and cause danger.

• The cleaning liquid should be kept out of reach of children. If the cleaning liquid accidentally gets into eyes, rinse thoroughly with clean water; in case of accidental ingestion, seek medical treatment immediately. Follow local environmental protection regulations when handling wastewater and cleaning liquid.

The MIDEA VSS GX5 has the following modes:

• Auto mode: The machine wets the brush-roll to clean the floor.

• Quick suction mode: The machine stops discharging water and sucks up dry garbage or residual water.

• Electrolyzed Water: This mode uses a cleaning and disinfecting agent obtained through electrolysis of a dilute sodium chloride solution. It is harmless to the human body and friendly to the environment.

Installation:

Insert the end of the handle into the port of the main unit along the vertical direction until there is a click, which indicates the installation is successful.

Removal:

Insert a screwdriver or other tool into the disassembly hole, and pull the handle upward.

For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance. Please charge the product before the first use.

1. Insert the charging end of the charger into the rear port of the charging dock, and connect the plug to a 100V-240V power source.

2. Place the MIDEA VSS GX5 machine upright into the charging base, ensuring the bottom of the body completely falls into the base. A voice will prompt “start charging,” and the indicator light will flash.

3. It takes about 3-4 hours to fully charge the machine. When the battery is fully charged, the indicator will turn off, and the machine will automatically power off.

Only fill the clean water tank with water.

1. Hold the machine with one hand, grab the water tank with the other hand, then rotate and remove the water tank.

2. Unscrew the water tank cover, pour tap water into the tank, and add an appropriate amount of cleaning solution if desired.

3. Screw the water tank back into place on the machine. When you hear a click, it means the installation is successful.

Step 1

Step on the floor brush and pull the handle diagonally until you hear a click. The MIDEA VSS GX5 is now in standby mode.

Step 2

To start working, press the power button. Press this button again to stop the machine.

Step 3

The machine defaults to automatic mode when it starts. To switch to the sterilization mode, press the mode switch button. Press this button again to switch to the suction mode.

Attention: After using the machine, it is recommended to place it vertically on the specially designed charging base.

In a working state, you can step on the floor brush to erect the body of the MIDEA VSS GX5. The machine will stop working and enter standby state. It will automatically turn off after 2 minutes of standby.

Caution:

• During the air-drying process, the machine does not charge. After air-drying is complete, it automatically enters the charging state. It is normal for the machine to indicate low battery after air-drying in a low battery state.

• In the air-drying mode, to improve the drying effect, the rolling brush will rotate every 2 minutes with a “drip” sound, which is a normal phenomenon.

Instructions:

1. When the machine is in a charging state, short press the self-cleaning button to activate the self-cleaning and self-drying mode. During the self-drying process, the roller brush rotates for 30 seconds for centrifugal drying, followed by the low-speed operation of the fan for 90 minutes to properly dry the roller brush and pipeline.

2. When the machine is in a charging state, long press the self-clean button for 3 seconds to directly enter the self-drying mode.

3. To stop the self-cleaning or self-drying, press the self-cleaning button again.

4. After the self-cleaning is completed, please clean the wastewater tank in time. If there are residual stains on the base, please clean them in time.

Attention:

• After cleaning, it is recommended to place the machine upright in the charging base; do not place the machine in places with direct sunlight or moisture.

• To not affect the performance of the machine, it is recommended that you regularly maintain its parts.

• Before cleaning, please disconnect the power supply to stop the machine.

• Scrub with water or neutral detergent, wring out the cleaning cloth before scrubbing to avoid water leaking into the electrical components.

Cleaning Steps:

1. Press the button of the wastewater tank with your thumb and pull outward to remove the tank.

2. Hold the tank with one hand and pull out the top cover of the tank with the other hand.

3. Dump the sewage from the side of the sewage tank and rinse it clean; remove the filter from the top cover of the sewage tank, rinse it clean, and air-dry it.

4. Install the wastewater tank back to the machine until there is a click sound. When installing the wastewater tank, it is recommended to hold the body with another hand to avoid tipping over.

Attention:

• It is recommended that after each use, the roller brush and cover should be cleaned and dried in time.

• If residual stains are found on the suction surface of the floor brush, wipe it with a wet cloth. Do not rinse it with water.

Cleaning Steps:

1. Press the buckle as shown in the diagram to remove the floor brush cover.

2. Rotate the end cap knob as shown in the diagram and pull out the roller brush sideways.

3. If there is still hair or other debris tangled on the roller brush after self-cleaning, remove the tangled debris. For heavy-duty cleaning (such as tomato sauce, soy sauce, etc.), if there is still dirt residue, it can be self-cleaned again or the roller brush can be removed and cleaned with water.

4. If there is residual dirt on the roller brush cover after self-cleaning, rinse the roller brush cover with water.

5. If there are any residual stains on the suction nozzle (the part exposed after removing the roller brush) after self-cleaning, please wipe it with a damp cloth instead of washing it with water.

6. After cleaning, reinstall the roller brush. If not in immediate use, you can place the roller brush in a ventilated area to dry before installation.

7. After cleaning, cover the floor brush, align it with the installation hole, press it down, and you will hear a click when it is successfully installed.

Please check the following table for solutions to common issues with your MIDEA VSS GX5.